Search Documents

By Freddie Hunter

An underground mining method for extracting an eight metre (26') coal horizon, containing a sandstone layer. A decrease in the thickness of the rock strata between the number two and number three seams of the Sasolburg Coal Field, has resulted in a total mining horizon approximately eight metres (26') thick. This parting varies in thickness and competency and in some areas is impractical to cut with a continuous miner. In addition, the general mining area is highly jointed. The top seam is first mined to a normal bord and pillar plan with a continuous miner. The bottom seam is then mined by selectively undercutting the stone parting constituting the floor of the top seam. In areas where this parting is between 0.75 - 2.50 metres (29.5" - 98") thick, it is suspended from the primary roof support installed when mining the top seam. Secondary, high extraction retreat mining is then undertaken in the coal pillars adjacent to the suspension supported headings in the bottom seam. Left in-situ, the parting provides lateral support to the pillar sidewalls in both the top and bottom seams, enabling high percentage extraction rates in what was previously thought an uneconomically mineable area. The paper proposed, presents the challenges and practical implications of executing the mining method, including the primary roof control of the top seam and the stone parting between scams.

Jan 1, 2003

By Nan Hua

As a high production and high efficient mining method, top coal caving method is now widely used in China. However, as more extra-thick coal seams are mined, it becomes more and more difficult to make the top coal fully broken up, resulting in more and more top coals flowing into the gob, rather than onto the rear AFC at the working face as designed. This research is aimed to investigate the failure mechanisms of the extra-thick top coal caving mining method.

Jan 1, 2009

By John Hoelle

Coal mines in southern West Virginia, south-western Virginia and eastern Kentucky have experienced coal bumps at least since 1933. Most of the bumps have occurred due to high cover, strong roof and floor strata and stress concentrations due to the mining sequence. A longwall mine in eastern Kentucky first experienced coal bumps on the tailgate side of the longwall face in 1989. The bumps continued until 1996. The bumps were the result of: Thick overburden up to 2200 feet Strong roof and floor (strata strengths up to 25,600 psi UCS and elasticity modulus up to 4,800,000 psi Previous over-mining in places Sandstone channels Not all characteristics occurred simultaneously. The bumps produced seismic events recorded up to 4.3 (Richter scale magnitude), and damaged pillars that were up to 147 by 152 feet in size.

Jan 1, 2008

By Qiang Fu

ABSTRACT This paper aims to identify the main issues concerning top-coal loss and the optimum drawing interval of LTCC (Longwall Top-coal Caving) mining by underground tests and DEM (Distinct Element Method) modeling. By extracting a new roadway in the goaf of the mined LTCC Panel No.4318 in Wang Zhuang coal mine of Lu-an CMA (Coal Mining Administration), and underground observation of the distribution of loss coal and broken rock in different sections of the roadway, this paper analyses the composition and presents a 3-D distribution map of the loss coal in the exploration roadway. This study indicates that the DEM modeling of broken top-coal is reasonable and scientific as it can simulate the movement of broken coal and waste rocks and determine the optimum drawing interval of top coal.

Jan 1, 2002

By W. C. Lacy

Stratabound copper ore bodies in thick Proterozoic metamorphosed sedimentary and volcanic rocks at the Tong Kuang Yu Mine in southern Shanxi Province of China were considered as possibly being amenable to block cave mining. Initial evaluation of caving characteristics was based upon old calyx drilling records, limited underground mining experience and geological mapping, a few diamond drill holes and measurements in surface subsidence features. Classification and mapping distribution of rock quality types aided in mine design, prediction of fragment sizing and explosive requirements, cave assist and ground support requirements. Comparison is made between early feasibility predictions and actual mine experience.

Jan 1, 1989

By David Bigby

In the UK, it is becoming increasingly necessary to open new longwall mining areas above old, abandoned workings. In such cases, strategic and gate roadways must often be driven and maintained across highly stressed areas and pre-existing and sometimes only recently formed subsidence troughs. Ground control at the edges of the subsidence trough can be particularly problematic, with complex combinations of stress and rock conditions being encountered depending upon the precise position in relation to underlying pillar edges. For economic recovery of these reserves, it is essential that rockbolt support is used wherever possible. It is therefore very important to the industry to develop its understanding of ground conditions and support requirements in these areas. This paper describes; ? the historical background to these problems and a series of documented UK case studies from the last 20 years. ? the experiences at UK Coal?s Riccall colliery, where a number of longwall panels were worked at a depth of around 800m, some 65m above previously worked longwalls. Actual experience is compared with pre-mining expectations and model predictions. ? design considerations and experience to date at UK Coal?s Welbeck and Thoresby collieries, which are embarking upon a series of longwalls in the Deep Soft seam, 30-40m above previously worked longwalls. The paper outlines numerical modelling techniques used to optimise such mine layouts within the complex geological and geometric constraints of a mature coalfield. These involve combinations of 2D and 3D finite difference and 3D boundary element models. It also discuss new modelling approaches which will be investigated in forthcoming EU funded research.

Jan 1, 2007

The scope of this paper is to introduce a mathematical model based on matrix algebra in order to determine similitude quantities, which can be arranged in specific formats to simulate the field conditions and associated behaviour. The formulation of a typical mathematical model applicable to Geomechanics is demonstrated here. The examples provided are intended to facilitate comprehension and application of the proposed model in practice.

Jan 1, 1989

By Morgan M. Sears

In recent years, one large mine collapse and numerous smaller bump events have resulted in a renewed interest in coal bump research. With numerical modeling, the Energy Release Rate (ERR) calculation quantifies the ?release? of the gravitational potential energy of the rock mass into the environment as mining progresses. This release of energy can occur passively in the form of heat and sound or dynamically in the form of pillar bumps or rock bursts. From the initial application of a calculated energy release rate in the deep hard-rock mines of South Africa, the ERR was found to have a significant correlation with the risk or potential of damaging coal bumps or rock bursts. In this research, an ERR calculation is incorporated into the modern LaModel program to facilitate the analysis for potential coal bumps. Initially the ERR calculations in LaModel are verified using a case study of cut sequences originally modeled using the MULSIM/NL program. Then, the ERR calculations are applied to a bump-prone mine in Southern Appalachia were a number of different pillar recovery cut sequences were used in order to minimize the risk of bumps.

Jan 1, 2009

By Ke Yang

In Chinese coal mines, extraction of deep, highly gassy soft coal seams sandwiched between soft floor and soft roof in complicated geology is commonly encountered. How to safely and efficiently excavate such seams is a very significant and important problem. It has been a focused research area in recent years. By combining the characteristics of fully mechanized longwall mining methods such as large cutting height and mining along the dip, an integrated method and technologies for the Zhangji Coal Mine were developed. This technology includes the design of a complicated geological exploration system, optimization of mining method and working face parameters, control of rock pressure and high levels of gas, reliability model of the production system, and selection and compatibility of equipment. Engineering practice shows that the integrated technology was successful in mining these complicated seams. This study not only enriches the mining method, but also improves the coal mining practice, especially ensuring both safety and productivity under complicated geological conditions.

Jan 1, 2009

By Christopher C. Woomer

Cyprus Shoshone Mine uses the longwall method to extract a deep, thick, pitching coal seam in the Hanna Basin of South Central Wyoming. The immediate, and main roof rock consists of weak, thinly-bedded, silty mudstones with weak, interbedded fine-to medium-grained sandstone. Tailgate ground control has been a critical factor impacting productivity at the mine. A gateroad condition mapping program for the 11 left longwall gateroads indicated potentially severe ground control problems for the tailgate. It was predicted that the existing, secondary support pattern of wood cribs would not provide adequate support capacity. As predicted, severe deterioration of the tailgate occurred in the form of a roof cutter, sloughing ribs, and failing wood cribs. Productivity was affected and additional support was required. Shoshone personnel evaluated several options for providing the additional support needed in the tailgate. The additional support system and placement method had to satisfy several requirements with respect to access, materials handling, placement method, set-up time and support capacity. Approximately 6,000-ft. of deteriorating tailgate had to be supported. The initial wood crib support system left a 6-ft. walkway for access and construction of the additional support. This access was further reduced as the roof loaded the wood cribs. This eliminated the possibility of mechanized material handling to the construction locations. All materials would have to be transported by hand. The additional support system had to be placed quickly to stay ahead of, and keep pace with, the required longwall advance rate. It had to incorporate the existing wood cribs and provide at least 500 tons of extra support capacity. And most critically, the system could not affect longwall ventilation. Longwall coordinators and engineers made the decision to use a low density, pumpable cement known to the industry as TeksealTM, to provide the system required. A 200 psi ultimate strength mix was decided on to provide the required load capacity. The existing cribs were formed with 1-in. by 6-in. boards and brattice cloth to provide the containment. To overcome the access limitations, three boreholes were drilled from the surface to the tailgate on 2,000-ft centers. A mobile pumping station was established on the surface and the TeksealTM was pumped 900-ft. down the boreholes through a 1.5-in. steel pipe, then as much as 1,800- ft. along the tailgate entry through 1.25-in. miner spray hose. The materials required for the TeksealTM supports could all be carried into the construction locations by hand. As a direct result of incorporating relatively new methods of pumping high yield, low density, cementitious grouts, the Shoshone Mine reduced downtime due to tailgate ground control problems by approximately 70% in comparison with previous Longwall panels. The longwall set three monthly production records while mining the 11 left longwall under the deepest cover, steepest pitch, and most extreme ground control conditions ever encountered at the mine.

Jan 1, 1995

By Khaled Morsy

Cementitious seals are made of foamed cements with strength ranging from 100 to 600 psi. These cementitious seals are usually used at locations where the seal will be subjected to some convergence, assuming that this material can absorb entry closure without compromising the structural integrity of the seal. Prior to 2006, Lake Lynn Experimental Mine (LLEM) conducted full-scale tests on various cementitious seals designed to meet or exceed the 20-psi horizontal static load requirements of the old 30 CFR1 75.335. Both hydrostatic and dynamic loading tests were conducted. The structural response (pressure and displacement readings) obtained from these tests were recorded. The stability of the cementitious seal is based on balancing the load applied to the face of the seal from the explosion against the shearing resistance at the seal/rock interface. Therefore, the properties of the seal/rock interface, such as stiffness, cohesion, friction, etc. are critical to determine the stability of a cementitious seal. These properties are usually assumed by the researchers in their models. This paper emphasizes the importance of having the correct properties of seal/rock interface in the numerical modeling. FLAC 3D models were developed to simulate Celuseal2 cementitious seals subjected to both hydrostatic and dynamic loadings. Using the hydrostatic and dynamic loading test data conducted at LLEM, the static and dynamic properties of the seal/rock interface were back calculated. The FLAC 3D models showed good agreement with the test results.

Jan 1, 2009

By Abouzar Vakili

Longwall Top Coal Caving (LTCC), as the most attractive method for thick coal seams, has been suffering from insufficient geomechanical understanding for the past few years. Cavability without doubt is the most critical geomechanical issue associated with the top coal caving method. A discontinuum method has been used for comprehensive modeling of LTCC operation by using the Universal Distinct Element Code (UDEC). In addition Particle Flow Code (PFC) and Phase2 were used as support for the caving mechanics analysis. Although the previous researches of gravity flow in caving operations neglected the effect of continuous span expansion, it has been observed in this study that face advancement has a great impact on roof symmetrical behavior. The amount of symmetry fluctuates between different face distances. Horizontal displacement seems to be the best indication for roof symmetrical evaluations. Two critical caving conditions have been modeled and parameters such as horizontal displacement, caving angle and recovery rate have been compared thoroughly. Results show that unsymmetrical behavior on the roof is closely related to face stability.

Jan 1, 2007

By Hamid Maleki

Prudent design of coal pillars in any mining system requires an estimation of in-situ pillar strength, overburden lateral load transfer capability, and a failure criterion. Pillar strength is typically determined using one of several different empirical pillar strength formulas. For coal reserves in the U.S., a new pillar design method was proposed based on extensive U.S. field measurements in underground mines (7) which accounted for confinement effects. Field measurements in seven U.S. seams indicated highest strength for some Utah mines where the coal seam developed high confining stresses. Lower strength was measured in structurally controlled seams. This method is expanded here including the data from the weaker tertiary coal measure rocks and lower confinement for pillars with low width-to-height ratios. The determination of how much load a pillar is expected to take is partially dependent on the ability of overburden to transfer load laterally; this is useful for selection of panel width and barrier pillars size in select mining applications where long-term stability is required in conservative designs. In caving mining systems, caving of the strata is influenced by geologic, mining and stress conditions and the released energies influences how the pillars react at loads approaching pillar strengths. Overburden deformation and caving mechanisms are analyzed in this paper in multi-panel extractions to enhance the understanding of load transfer, seismicity and coal bump control in deep western U.S. operations.

Jan 1, 2008

By Stephen C. Tadolini

The International Ground Control Conference in Mining has always provided an open forum for the publication, presentation, discussion, and often heated debate on roof bolting systems mostly with attention to how, when, and why they work. During the last 24 Conferences at least 170 papers have been presented by International Experts on these ?simple? devices that range in length from 30-inches to 20 ft and from 5/8 to 2 inches in diameter. Roof bolts are primarily mechanically anchored, glued, cemented, or driven. Bolts are placed vertically, angled, or tied together with special fixtures (trusses and slings). They have been termed active, passive, stick-slip, and several other descriptive acronyms or mining slang expressions. This retrospective paper will present the changes in bolt types and usage, point out some of the biggest myths and hail the most significant advances (according to the authors? opinions of course).

Jan 1, 2006

By R. Karl Zipf

The sudden, violent collapse of large areas of room-and-pillar mines poses a special hazard to miners and mine operators. This type of failure, termed a "Cascading Pillar Failure" (CPF), occurs when one pillar in a mine layout fails transfering its load to neighboring pillars causing them to fail, and so forth. Recent examples of this kind of failure in coal, metal and nonmetal mines in the U.S. are documented. Mining engineers can limit the danger posed by these failures through improved mine design practices. Whether failure occurs in a slow, nonviolent manner or in a rapid, violent manner is governed by the local mine stiffness stability criterion. This stability criterion is used as the basis for three design approaches to control cascading pillar failure in room-and-pillar mines, namely, the containment approach, the prevention approach, and the full extraction mining approach. These design approaches are illustrated with practical examples for coal mining.

Jan 1, 1996

By Christopher Mark

Knowledge of in situ stresses is fundamental to many studies in earth sciences, and coal mine ground control is no exception. During the past 20 years, it has become clear that horizontal stress is a critical factor affecting roof stability in underground coal mines. The theory of plate tectonics and the World Stress Map (WSM) project has been extremely helpful in explaining the sources and the orientations of the horizontal stresses observed underground. Recently, WSM geophysicists studying deep-seated stresses have developed a model of how stress magnitudes vary with depth in the crust. They have devoted relatively little attention to near-surface stresses, however. This paper explores the relationships between deep-seated and shallow in situ stresses in several of the world?s coalfields, using a data base of more than 350 stress measurements from underground coal mines. The analysis indicates that distinct regional trends exist, corresponding roughly to the regional stress fields identified by the WSM. The paper presents equations for estimating stress magnitudes that were developed by treating depth and elastic modulus as independent variables in regression analysis. The magnitude of the horizontal stress increases with depth, at rates that range from 0.8 to 2.0 times the vertical stress, just as the WSM ?critically stressed crust? model predicts. Overall, it seems that the stress regimes encountered in underground coal mines are closely linked to those that exist deep in the earth?s crust.

Jan 1, 2008

By Andreas Hucke

For the roadway design in the German hard coal mining industry, an advanced combined planning system has been applied during the past 20 years. The German mining industry is working with single entry roadways system. After first longwall passage the roadways will be stabilised with side wall building material packages. Later this roadway will be used again for the second retreating longwall. The intention of the implementation of several different design methods for the planning of the roadways is to enhance the reliability of the results. On one hand the planning system uses numerical simulation and physical modelling in addition to analytical and empirical methods. On the other hand in-situ monitoring and analysis during the roadway development will be used to verify and calibrate the numerical and physical models. Especially before the implementation of new support elements in underground, this system is suitable and reasonable because the new support elements will be tested in the physical and numerical simulation prior to cost intensive underground tests. The interaction between the numerical and physical modelling in comparison with underground monitoring and analysis during development and the later use of roadways will be shown with some examples. The first example shows a rock bolted rectangular roadway which will be mined at both sides of the roadway. Different support and roadway building material package systems are investigated under various stress conditions. The results are utilised to optimise the roadway support and the roadway side package systems. The influence of different points in time of the installation of several support elements in a combined arch and bolted roadway is shown as another example. Two different types of support systems are compared within the physical models. These models are used as a base for ongoing numerical analysis and simulation to find out the ideal point of time to assemble the different support elements. The last example handles the influence of slickensides in the roof of arch shaped roadway on their stability. Different slickenside positions and densities are investigated and classified.

Jan 1, 2006

By Fan Shaogang

In this paper, the airbags' structure and technical characteristics and its applications in China are described. Based on the practice of the airbags in mining thin seams, the effects on ground control are discussed. This paper also analyzes the interaction mechanism between the airbag and surrounding rocks.

Jan 1, 1997

By John D. VandeKraats

Yielding rock bolt support systems have been developed to accommodate ground movement in shifting ground such as in coal operations; in creeping ground such as salt, trona, and potash; and in swelling ground associated with some clays. These systems, designed to remain intact despite ground movement, should enhance mine safety and help contain costs in areas where rebolting of rigid non-yielding systems is typically required. Four such systems were tested in straight tensile pulls in the laboratory. They include the Slip Nut System from Dywidag Systems International USA, Inc., Ischebeck's bolt mounted Titan Load Indicator, Rocky Mountain Bolt Company's Yielding Cable Bolt, and a rock bolt installed variation of the yielding steel post developed by RE/SPEC Inc. The first two systems are currently marketed products and the latter two are prototype systems. Each system responds to load and displacement by yielding in a unique manner. All are designed to yield at predetermined loads. A description of each system and its yield function is provided. Each system was tested over its prescribed yield range in a test machine. At least five tests were performed on each system. Each system yielded and continued to provide support according to its design. Each shows promise for ground control use in shifting or creeping rock. This work helps to illustrate the comparative differences in performance between these specialized systems and the applications where they may be most useful.

Jan 1, 1996

By Dan Payne

The Crinum mine has recently completed workings in the southern area of the mine. Over the 10 years of longwall production 40 million tonnes have been extracted and the mine has experienced over 40 longwall face, 3 main gateend, and 2 tail gateend roof falls as well as 5 roadway roof falls away from the longwall. Weak roof (less than 10MPa (1450psi) in the bolted horizon) has been the principal roof control issue at the mine. However, weak, highly cleated coal, water inflow from overlying aquifers, some minor structure and a diatreme in the main headings have also contributed to the challenges at the mine. This paper describes the geotechnical experience over the 10 years, the mine?s approach to addressing the issues and the relative success of these approaches.

Jan 1, 2008