Search Documents

By Fouad Faraj

For every blast pattern, zones of unique material types need to be classified before mining. Most material types can be summarized into different kinds of ore and waste. Blocks generated from blasthole assays are too small to be selectively mined, so areas with a single material classification meeting the mine’s selective mining unit must be defined. Current industry standard practices are to manually draw ore/waste dig limits, but this process is subjective and results in quantities of dilution and ore loss that can be improved upon to enhance the profitability of mining operations. In this study, two weeks of production data from a homogeneous copper (Cu) porphyry and heterogeneous manto-type Cu deposit were used to assess the variability in the hand-drawn dig limits of 20 geologists, mining engineers and ore control specialists, which were compared with the optimal ore/waste delineation. The profit for 20 distinct hand-drawn dig limits for the homogeneous mine varied by 3.7 percent, from $10.5 million to $10.9 million, averaging at $10.8 million. The percentage was nearly double for the more heterogeneous mine at 5.9 percent, from $17.9 million to $19.0 million, averaging at $18.6 million. Using the optimal ore waste delineation, the profit increased to $11.0 million (1.9 percent increase) and $19.3 million (7.0 percent increase) for the homogeneous and heterogeneous deposit, respectively. The natural variability, diggability requirement and selectivity are identified as the main drivers of ore loss and dilution. Recommendations are provided for reducing the subjectivity in manual hand-drawn dig limits by integrating dig limit optimization algorithms as a tool to assist practitioners.

Oct 1, 2024

By Richard Kastner, Emilie Vanoudheusden, Fabrice Emeriault, Jacques Robert

INTRODUCTION The subway line B of Toulouse (France) has been realized with three different tunnel boring machines (TBM) techniques: Contracts 2 and 5 are excavated with earth-pressure balanced TBM, Contract 4 with a slurry shield TBM, and Contract 3 with a compressed-air TBM. The first three machines are around 7.7 m in diameter, while the last one is 5.3 m. Moreover, a small part of the line (50 m) has been excavated by a conventional method. The tunnels run through the Toulouse molasses, composed of hard sandy clay with pockets and lenses of dense sand. Geotechnical investigations have shown that in these formations, K0 is greater than 1, around 1.8 at a depth of 25 m (Serratrice,2005) and that geotechnical characteristics are homogenous on the whole layout (? =22 kN/m3, Su = 300 kPa, c' = 30 kPa, F' = 32°). The water table is found between 2 and4 m below ground level. As geology, stratigraphy and tunnel cover (between 10 and 20 m) are almost identical, a comparison of movements induced by the excavation by each of the four excavation techniques is possible. This paper presents the soil mass movement measures in the case of the conventional excavation method and in the case of TBM sections. It shows how tunneling parameters may explain the different surface movements observed during excavation. For the sake of simplicity, only the results of Contract 2 (earth pressure balanced TBM)will be presented. MONITORING Monitoring for the Conventional Method Section For the conventional method section (Vanoudheusden et al. 2005) the mass soil movements are measured with two inclinometers and one multi-point extensometer borehole with automatic data acquisition (Figure 1). The monitoring devices include

Jan 1, 2007

By B. Radwanek-Bak

The assurance of future raw materials supply to the EU mineral industry has become, in recent years, one of the most important tasks of the EU Commission. It is focused on creation a new mineral policy within the EU zone. One of the starting points for this activity was identification of the mineral commodities that are critical for the sustainable development and technological progress. The paper presents the glance to this problem from the National Member level. Domestic mineral reserve base as a possible source of critical raw materials for the EU was shown. Poland cannot be considered as its resource base. The source of these raw materials are not only scarce in Poland, but also they are not produced, and their demand is now - and according to forecasts is going to be in the future - met by imports. The raw materials in question are not considered exactly critical for Polish economy, but they are of limited economic importance. On the other hand, their growth is a best opportunity and at once the need to the future sustainable development.

Jan 1, 2011

By José Mirão, Pedro Madureira, v Costa, Patrícia Conceição

"The exploration of seamounts south of the Azores during the EMEPC/Açores/G3/2007 campaign allowed for the collection of 30 Fe-Mn crusts from the Atlantis, Great Meteor, Small Hyeres, Irving and Plato seamounts, as well as from the East Azores Fracture Zone. These were the first samples of Fe-Mn crusts studied from these seamounts. The Fe-Mn crusts were analyzed using multiple analytical methods.The crusts are fairly homogeneous, showing typical textures for this type of occurrences. The Fe/Mn ratio, patterns and concentrations in rare earth elements, and the great homogeneity of the crusts lead to the conclusion that they have a hydrogenetic origin, precipitating directly from seawater. Although the content in Fe and Mn of the crusts is consistent with data available for the Atlantic, the mean concentration of Co is comparable to the average values for the Pacific. Cu and Ni show lower values than the ones known for the Pacific."

Sep 1, 2014

By John Sleavin

As part of the Link Light Rail project in Seattle, WA, work was completed at the Pine Street Stub Tunnel (PSST) in early 2007 for the Central Link project. This tunnel was excavated using cut-and-cover construction within the limits of Pine Street. The stub tunnel provides a turn back via double crossover for light rail trains running in the Downtown Transit Tunnel (DTT), as well as a connection point for the next phase of the project, the University Link (Fig. 1). Designing the new University Link tunnel connection to the existing PSST was a tricky task. The on-site geotechnical conditions, buried obstructions, geometry, requirements for construction and balancing operational considerations and neighborhood stakeholder concerns associated with the recently completed PSST combined to create a uniquely challenging assignment.

Jan 1, 2010

By Faruk Oksuz, Cary Hirner, William A. Rochford

Grouting is a frequently utilized remedy in the planning and implementation of ground improvement and tunnel rehabilitation practice. The state-of-art grouting application used for Chicago’s McCook Reservoir project offers a unique alternative to the tunneling industry for pre-excavation grouting as well as tunnel rehabilitation, rescue and post-excavation ground improvements. The McCook Reservoir project included a computerized grouting control and data collection system for a precise and highly effective groundwater cutoff in fractured dolomites. By using balanced and stabilized grout mixes, the effective permeability of the rock mass was reduced over two orders of magnitude to less than 0.1 Lugeon by installing a double line grout curtain. The stable grout mix designs allowed high pressure and effective grouting at depths up to 125 m (410 ft).

Jan 1, 2005

By L. G. Stolarczyk, Y. Luo, S. S. Peng

Detection and assessment of severe geological anomalies ahead of a longwall face greatly benefits the mining operation. Electromagnetic-based Radio Imaging Method (RIM) is one of the most promising geophysical methods for this task. Based on two decades of development, the latest RIM instrumentation (RIM-IV) has expanded its operational range up to 1,800ft.A site demonstration of the RIM-IV technology was recently conducted within a longwall panel. An extensive ground truth study was performed to evaluate the accuracy of the RIM survey results. This study compared the generated RIM tomograms of attenuation rate with the mapped geological anomalies. Three different approaches have been employed to examine the accuracy of the RIM results and to correlate the measured signal attenuation rates with physical properties of the coal seam. The study shows that the RIM-IV technology is able to identify and delineate those geological features that would severely affect the longwall mining operation.

Jan 1, 2004

By M. S. Miller

With prevailing assumptions that plentiful domestic coal reserves will be available for meeting our Nation’s expectations for on future low emission, coal-fired power plants, major government funding in Clean Coal Technology, and Carbon Sequestration Programs continues to be aggressive. However, after more than a decade of cutbacks in funding for domestic coal-related programs and personnel, there is a growing concern that adequate quantification and qualification of our Nation’s coal reserves is increasingly being compromised. This paper will define the growing concerns and dichotomies that continue to increase, and address the decreasing number of fossil fuel mapping and assessment programs by Federal and State programs.

Jan 1, 2004

By G. F. Jenkins, P. S. Hobden

Toronto as a geographical area provides an exceptionally wide variety of subsoil stratiphication. Tunneling consequently required a very wide range of adaptabilities to meet its changing conditions. This discussion will provide a summary of work performed in both earth and rock formation using three of our recent works to describe a Contractor's experience. The general subsoil stratigraphy is known to consist of deposits laid down during the Illionian Glaciation followed by the Samgamon Interglacial Stage and finally the Wisconsin Glaciation. All these deposits are underlain by shale bedrock of the Dundas formation. As a whole the Dundas formation is predominantly a greyish blue, thinly bedded shale. The engineering characteristics of the shale vary considerably, however, between a blue clay (argillaceous) shale and a much lighter (in colour) silty and sometimes sandy (arenaceous) shale, and occasional limestone layers. The Illionian deposits are usually found to be layers of pebbly clay till and an overlaying layer of contorted varved-clay. These glacial deposits can be overlain by a thick layer of sandy silt to silty sand which is identified as the Samgamon Interglacial sediments. Because of the action of erosion the Wisconsin till sheets, many times separated by interstadial sands, can vary greatly in their number of layers from zero to three or more.

Jan 1, 1997

By Borje Bjorkvall

At LKAB's plants in Lappland, Sweden, sintered pellets are manu-factured according to three different industrial processes, viz. shaft furnace at Malmberget, straight-grate at Kiruna and grate-kiln at Svappavaara. At present the total annual capacity amounts to 4.7 million tons. However, since it has been decided to erect a new straight-grate plant (2.5 million tons) at Malmberget, and because of the decision to extend and rebuild the existing plants, it is estimated that the annual capacity will be increased to somewhat over 8 million tons by 1973. The great majority of the pellets produced is exported. They are thus reloaded several times and generally speaking roughly handled, resulting in larger or smaller product losses on arrival at the point of use. It is there-fore of great economical interest to have a good control over the transport strength of the pellets by appropriate quality testing at the point of production. In addition to good transport strength, further demands are ob-viously made on pellets destined for blast furnace operation. The blast furnace burden must maintain a good permeability for the gas. The pellets must thus have a favourable size distribution and must not be so weakened by reduction that they disintegrate under the stresses and clog the blast furnace shaft. Furthermore, the burden must have good reducibility. An increase of the rate of reduction can obviously mean increased blast furnace capacity and reduced coke consumption. In order to optimise the properties of the pellets in these respects, the producer must also be thoroughly familiar with their behaviour during reduction, particularly as the customer's interest in the reduction properties of the pellets' has increased over the last few years. Up to now the only quality demands the customer has made have generally had to do with the cold strength and the screen analysis. Thus a quality control of in addition to good transport strength, further demands are obviously made on pellets destined for blast furnace operation. The blast furnace burden must maintain a good permeability for the gas. The pellets must thus have a favourable size distribution and must not be so weakened by reduction that they disintegrate under the stresses and clog the blast furnace shaft. Furthermore, the burden must have good reducibility. An increase of the rate of reduction can obviously mean increased blast furnace capacity and reduced coke consumption. In order to optimise the properties of the pellets in these respects, the producer must also be thoroughly familiar with their behaviour during reduction, particularly as the customer's interest in the reduction properties of the pellets' has increased over the last few years. Up to now the only quality demands the customer has made have generally had to do with the cold strength and the screen analysis. Thus a quality control of

Jan 1, 1972

By Jayant Khambekar

In a typical mining operation, run-of-mine (ROM) ore is crushed and screened to achieve a desired particle size distribution and then fed to processing equipment for further refining. For an operation to be profit-able, the ore handling system from the mine face to final product loadout must be reliable. However, the handling system components do not always perform as expected and production problems related to material flow occur. These problems include flow stoppages, limited live storage capacities, uncontrollable flow, segregation, spillage and dust emissions. These result in lost production, excessive maintenance, safety and environmental issues, and even structural failures, in some cases. Flow patterns Flow problems and their solutions can be best understood by first learning how bulk solids flow. As bulk solids discharge by gravity from a storage system, primarily two types of flow patterns can develop: funnel flow and mass flow. Figure 1 shows a schematic of these two flow patterns. In funnel flow, only a portion of the material is in motion during discharge, which flows toward the outlet through a channel that forms within the stagnant material. Funnel flow occurs when a hopper is not sufficiently steep and smooth to ensure flow along the walls or when the outlet is not fully effective. In mass flow, all of the material is in motion whenever any is discharged ? there is no stagnant material. Mass flow occurs when the hopper is sufficiently steep and smooth to ensure flow along the hopper walls. Shallow valleys are not permitted and the outlet must be fully effective. A third type of flow pattern, called expanded flow, can develop when a mass flow hopper (or hoppers) is placed beneath a funnel flow hopper or bin. The mass flow hopper is designed to activate a sufficiently large flow channel in the funnel flow hopper to avoid flow problems due to a rathole. The flow pattern in which a bulk solid discharges from a storage system strongly influences the flow problems that may occur in that facility.

Jan 1, 2009

By W. L. Hollinshead, Alwin Poltinger

GENERAL Tunneling by hand digging is as old as the history of humans. Mechanized tunneling did not begin to replace manual methods until around the beginning of the 19th century(Brunel patent, 1818). It brought with it a higher degree of safety for the workers and a much higher rate of boring. But for any kind of tunneling, an accurate and feasible method of survey must be accomplished during mining. That means, that for each tunnel project the most efficient survey method must be devised. The method to be defined depends on the spatial curve, diameter, speed of tunneling method, purpose of tunnel and contractual accuracy. The final accuracy of a finished tunnel is heavily dependent upon three critical elements: 1. Quality of the above ground survey 2. Tunnel traverse and directional transfer from above ground 3. Guidance for the mining job. Combining The Survey And The Guidance System Since the guidance system (GS) is one of the critical factors in the determination of the tunnel final accuracy, it is necessary to analyze how the directional control and tunnel traverse measurements can be effectively integrated into a GS. Any guidance system, whether manual or high technology, must continually detect and compensate for movement of its theodoliteor laser station standpoint. Movement beyond a preset allowable amount must generate a warning or error message to the user. Additionally, optical refraction can interfere with the results. Refraction will have an effect on any kind of optical GS. Therefore, careful selection of target and standpoint locations can minimize, but not completely eliminate, the influence of refraction. Some GS technologies, such as Gyro-based systems, are immune to the effects of refraction, but have other, methodical errors which will be described later in this paper. GUIDANCE Overview Why is a guidance system necessary? A GS, whether manual or automatic, compares the design direction and slope of a tunnel with the current position of the mining

Jan 1, 1997

By Graham Davey

High-speed stirred milling is a relatively new method of grinding in the metalliferous process industries. However, it has been widely used in the industrial mineral field for more than 30 years. Many existing metallurgical operations are looking to maximize economic return from existing deposits this requires new thinking and technologies. The operating experience of two copper operations is discussed here to show the effect of the introduction of the Metso Stirred Media Detritor (SMD), a new type of high speed stirred mill. Both operations have derived significant metallurgical benefits from this new technology. The benefits and process difficulties are explained. The initial drive in high speed stirred milling technology was toward ultra fine grinding where the mill product has an 80 percent passing size of 15 µm (937mesh) or less. More recently, a number of installations have occurred in a more conventional regrind setting. Few conventional copper concentrators require such fine grinding to attain satisfactory copper grades and recoveries. So other advantages must be considered here rather than just the ability to grind fine with good power efficiency.

Jan 1, 2004

By B. S. Van Gosen

In recent years, U.S. regulatory agencies have placed emphasis on identifying and regulating asbestos dust exposures in the mining environment, with a particular focus upon industrial mineral deposits in which asbestos occurs as an accessory mineral. Because asbestos minerals form in specific geologic environments, only certain predictable types of industrial mineral deposits can potentially host asbestos mineralization. By applying a basic knowledge of asbestos geology, the costly and time consuming efforts of asbestos monitoring and analyses can be directed towards those mineral deposit types most likely to contain asbestos mineralogy, while saving efforts on the mineral deposits that are unlikely to contain asbestos. While the vast majority of industrial mineral deposits in the Western United States are asbestos-free, there are several types that can, in some instances, host asbestos mineralization, or be closely associated with it. These industrial mineral deposits include a few types of aggregate, dimension, and decorative stone, and some deposits of chromite-nickel, magnesite, nepheline syenite, olivine, rare earth elements, talc, vermiculite, and wollastonite.

Jan 1, 2009

By Scott Ellenbecker

The formation in Newmont Mining?s Phoenix Mine near Battle Mountain, NV contains high levels of abrasive quartzite as well as gold, copper and silver. Newmont started mining operations at Phoenix (formerly Battle Mountain Gold) three years ago and the planners knew they were working with a challenging geological formation. But as it turned out, it was more challenging than anticipated. Mine manager Mark Evatz said, ?Anything that touches Phoenix rock wears fast. The rock fights back here.? To contend with the hard conditions, Newmont uses Atlas Copco?s Pit Viper 271 (PV-271) blasthole drill. Because of the hardness of the rock, drilling at Phoenix requires hammer drilling and the mine uses Atlas Copco TD65 hammers with 171 mm (6.75 in.) bits. The mine?s PV-271?s are outfitted with a single 41 m3/min (1450 cfm), 2.4 MPa (350 psi), oil-flooded air compressor. Phoenix has six Atlas Copco PV-271 drill rigs plus an Atlas Copco DML and a DM45 midrange blasthole rig. The mine?s goal is to keep 3.6 Mt (4 million st) of muck in inventory to stay ahead of the shovels and support needed operational flexibility (ore control related). Drilling efficiency has been a continuous point of improvement since operations began at the mine. The single-pass depth capability of 16.5 m (55 ft) on the PV-271 helped with that. Originally, the plans called for 6-m (20-ft) bench heights, supported by 7-m (23-ft) drill depths, and time spent moving from hole to hole was eating up productivity. Drilling on that plan resulted in drilling an average of 14 m/h (47 ft/hour). When depths were changed to 13-m (44-ft) drill depth, supporting blasting of 12-m (40-ft) benches, they were able to use the single pass capacity of the PV-271. Performance increased to more than 18 m/h (60-ft/hour) an hour. Although the drill depth change largely supported the improvement, other aspects of continuous improvement associated with improved knowledge of the Pit Viper drills helped as well.

Jan 1, 2009

By T. Rasmussen, T. G. Jørgensen, T. Fischer, R. K. McLimans, C. Knudsen, D. Frei

Ilmenite-bearing paleo-beach deposits were discovered in Jylland, Denmark using a combination of Ground Penetrating Radar (GPR), portable X-ray fluorescence (XMET), bulk XRF analyses, Computer Controlled Scanning Electron Microscopy (CCSEM), and wire line logging. The Miocene-age paleo-beach deposits are located below a thin Quaternary cover in a region of very moderate relief and essentially no outcrop demanding unique approaches in exploration. Initially, an isopach map of the Quaternary is prepared from existing water well data. A geological model for likely occurrence of Miocene paleo-beach deposits is generated and the coincidence of thin Quaternary cover and potential paleo-beach deposits define targets for detailed exploration. The defined targets are traversed with GPR to identify paleo-beach structures which are then used to define a drilling program. This methodology located a paleo-barrier island at the Vorslunde location with more than 10% ilmenite in the sand. During the drilling process, the TiO2 and heavy mineral contents of the sand were logged every meter with a portable XRF unit (XMET) and subsequently calibrated more accurately by comparison to bulk XRF and CCSEM analyses for selected samples. The bulk XRF data also provided more complete compositional information. Insitu determination of geology, heavy mineral abundance, and corroboration of the XRF logging was done using wire line logs, a combination of spectral gamma and induction conductivity logs. Detailed characteristics (abundance, grain size, shape) and chemical composition of minerals was determined by the GEUS CCSEM methodology (Frei et al, this vol.). The average weight percent TiO2 for all Ti-minerals is 62%, 60% excluding rutile. That elevated TiO2 content (>> ilmenite stoichiometric value, ca. 50 %) indicates that ilmenite experienced an iron-leaching environment. The source of the sand deposit was investigated by dating contained zircon. The results show that the likely sources of zircon are in southern Norway and southwestern Sweden with common zircon ages of ca 1100 Ma. and 1500 Ma.

Jan 1, 2005

By Robert Labbe

The final tunnel lining for this project involved pumping vast quantities of concrete over large distances under the extremely busy streets of lower Manhattan. Approximately 68,000 cubic meters (89,000 cubic yards) were pumped from various locations over 152 meters (500 feet) below ground (Figure 1) to create nearly 14.5 kilometers (9 miles) of 3.05 meter (10 foot) diameter tunnel. Total distances pumped exceeded 1,645 meters (5,400 feet) horizontally after a vertical difference of over 152 meters (500 feet). The urban setting of the operation, coupled with the long distances over which concrete was pumped, created many problems which had to be dealt with along the way. A three-shift labor operation was implemented to allow sequential pouring of tunnel sections nearly every day. The fine tuning of the mix design was critical to make this operation successful.

By H. Sevim

The utilization of high sulfur Illinois coal by utility plants has been decreasing since the enactment of 1990 Clean Coal Air Act Amendment. Illinois coal producers can make their coal saleable by offering the choice of taking the combustion by-products from the utility plants and placing them in the abandoned sections of their mines. To be competitive, however, coal producers need to select an environmentally acceptable transportation-handling-placement system through which the cost-per-ton of by-product disposed can be minimized. In this paper, a few such systems are presented. The favorable operating range of each system is determined in terms of distance and tonnage. A case study is given whereby cost analysis is conducted for an underground coal mine receiving by-products from two Illinois utility plants.

Feb 24, 1997

By Georgene Renner, William R. Yernberg, Steve Kral

ABB provides integrated pro-cess control, optimization and information systems, drives and power-distribution equipment as well as other services and support to the mining industry. ABB also supplies electrical equipment and control systems for the openpit mining industry. This includes products for the automation of electrical equipment in mine shovels. The company offers low- and medium-voltage drives for various mineral- industry applications. And ABB provides gearless mill drives for equipment, such as semiautogenous grinding mills that are too large for conventional drives. ABB Industrial IT provides innovative hardware and software systems that cover all the requirements of the modern mining and processing plant.

Jan 1, 2004

By M. I. Al-Wakeel

Nile sediment was collected as a waste from one of the water treatment plants in Cairo, and subjected to petrographical investigation and granulometric, chemical, and mineralogical analyses. It was expected to find diatomite in that sediment but it was a surprise to find that the diatomite content amounted to about 52.01% by volume in addition to quartz, orthoclase and clay minerals. The latter are represented by montmorillonite and illite minerals. The sediment is light gray in color, soft and has low density and high surface area, such density and surface area generally decrease with temperature. The sediment absorbs 317% of its weight in water. The diatomite skeletons are the main factor responsible for its high porosity producing microporosity and low density, and these particles are concentrated in the very fine silt size fraction (11x2µm). The common diatoms in such sediment include Cyclotella ocellata Pant, and Melosira granulata (Ehr.) Ralfs. It seems that this Nile diatomaceous sediment has many advantages over the fossil diatomite, such as Fayium diatomite in Egypt, with the absence of carbonate minerals that require grinding and calcination those cause destruction of the cellular structure and energy consumption. This Nile diatomaceous sediment can be processed using sequential classification to obtain diatomite concentrate of 88.8% grade at 90.6% recovery, and a middling product of 19.4% grade and 5.8% recovery. The suggested flow sheet is quite simple to produce diatomite product for different industries at a low cost. The unusual particulate structure and chemical inertness make diatomite an ideal mineral to be used as functional filler in a wide range of industries, and as catalyst carriers and insulating material. Key words: Egypt, Nile sediment, Diatomite, Beneficiation, Sedimentation, Classification.

Jan 1, 2008