Search Documents

By R. L. Loofbourow

Reasons for reexamining underground mining include: 1. The assurance that more deep deposits of useful minerals will be found. 2. The existence of deeply covered deposits of industrial minerals near large markets where quarries are becoming depleted or are lacking. 3. Surface property values, zoning and other limitations on open pit mining. 4. Expectation that underground space will be increasingly used for transportation, power plants, storage and similar purposes. 5. The improvements which have been made in underground mining. During the last three or four decades many changes and improvements have been made underground. All underground construction and mining has benefitted to some extent but the effect on the productivity of labor employed with some methods- has changed little and the use of these methods has declined. Productivity of labor in other methods has increased substantially. The relative usefulness of mining methods has changed and a vital industry, bituminous coal, has been returned to health. In this paper, consideration is limited to nine methods used with high productivity during the period under review. These methods are not necessarily better than others but they may be considered the prime methods in the sense that, in our economy, many, low grade ores, coal and the principal industrial minerals could hardly be produced by less productive means.2 Although most of the examples cited are from mining as such., the first four methods discussed can be used for the construction of stable excavations of various' shapes in sound rock.

Jan 1, 1967

By D. T. Iseley, A. L. Atta-alla

INTRODUCTION The extension project of the East Line Subway of Atlanta's subway network includes the construction of two single track transit tunnels under Interstate Highway 285. The project will be in DeKalb County, Georgia. The length, width, and height of each tunnel are 54.25, 6.3, and 7.2 m (178, 21, and 23 ft) respectively. The ground cover above the tunnel crown ranges from 1.5 to 3.25 m (5 to 11 ft). A soil pillar about 5.5 m (18 ft) wide will remain between the tunnels. The construction of each tunnel includes (i) installation of 21 steel soil support pipes of 75 cm (30 in) diameter, (ii) jet grouting 15 soil cement shafts of 60 cm (24 in) diameter in the soil under the pipes, (iii) contact grouting behind the tunnel lining and between soil support pipes and pavement, (iv) excavation of soil inside the soil support arch, and (v) installation of steel pile foundation, steel sets, and permanent tunnel lining of cast-in-place concrete, all as shown on the cross section in Fig. 1. The soil profile can be described from top to bottom as cement/asphalt concrete pavement, a fill layer consisting mostly of stiff sandy silt/firm silty sand, a residual soil layer consisting mostly of silty sand/sandy silt, partially weathered rock, and solid rock.

Jan 1, 1991

By Robert B. Crookston

This paper presents a resume and status report: of mining technology appropriate to commercial oil shale development in the United States today. The nature and extent of oil shale in Colorado and Utah are discussed. A look at most of the prominent activities now underway emphasizes the questions "where are we now?" and "where are we going?" Various alternate mining methods are reviewed and a bibliography of oil shale mining is included.

Jan 1, 1980

By Roger K. McLimans, Venkatramaiah N. Vasudev, Christian Knudsen, Stefan Bernstein, Dirk Frei

Computer Controlled Scanning Electron Microscopy (CCSEM) analyses of sediment samples from coastal regions of Kerala and Tamil Nadu states and the heavy mineral deposits of Chavara, South India, show large lateral differences in the titanium content in ilmenite due to varying degrees of iron leaching. As the depositional environments for the sands with varying degrees of ilmenite alteration are comparable, the cause for the different degree of alteration is due to differences in the primary source of the ilmenite or to differences in the geochemical history of the ilmenite grains during transport from source to deposit. The CCSEM analyses of the heavy mineral fractions show that source of sediments with a high content of titanium-enriched ilmenites, mainly the heavy mineral deposit around Chavara, resides in the khondalite belt of South India (granulite facies metasediments). The less titanium-enriched ilmenites are sourced from other rocks in the area such as the charnokites. Those conclusions are based on the high MgO content in the leached ilmenites, chemical composition of the accompanying garnets (low CaO and high MgO), and the concentration of aluminum-rich minerals in the sands.

Jan 1, 2005

By John Newby, Edward Kennedy, Ulf Gwildis

Alluvial deposits of major rivers often provide relatively uniform tunneling conditions. However, these conditions pose specific challenges due to the tunneling behavior of the granular soils as flowing ground, if unsupported. This paper describes the design considerations and construction experiences gained during the Tunnel Boring Machine (TBM) drives for the Annacis Island WWTP New Outfall System in the Vancouver, B.C. metropolitan area. Meeting the design criteria for connecting two (2) deep on-land shafts with an in-river riser manifold required advancing a 5-meter-diameter slurry TBM through the Fraser Rivers sands and at a tunnel invert elevation with a baseline hydrostatic head of 3.4 bar.

Dec 1, 2022

By David A. Newman

The Geomechanics Classification (Bieniawski, 1979) was modified for entry and roof support design in underground room-and-pillar coal mines. Adjustment multipliers were introduced to incorporate the influence of strata weatherability, high horizontal stresses, and the roof support reinforcement factor into the existing classification system. Sixty-two case histories of both standing and fallen mine roof were collected from two mines in the northern Appalachian coalfield. Twenty-seven engineering and geologic parameters were recorded for each case. A partial correlation analysis was carried out on the cases to establish which parameters have a significant impact upon the supported stand-up time of coal mine roof. Survival analysis, a statistical technique used in medical research to assess the effect of a drug or treatment on a patient's life expectancy, was conducted together with stepwise multiple regression to derive values for the adjustment multipliers. A practical example is included to illustrate the application of the modified Geomechanics Classification to underground coal mine design.

Jan 1, 1985

By B. Comley, M. C. Harris

There is as yet no accepted method of predicting flotation frother performance in plant processes based on laboratory scale characterisation techniques. This paper investigates the use of dynamic surface tension, using the maximum bubble pressure method, as a means of evaluating frothers and frother mixtures. An adsorption model is presented, which has been used to quantify the role of frother type and concentration during frother bubble interaction, based on the correlation of model parameters to physical frother characteristics. This approach was found to provide useful insight with respect to blending and selection of flotation frothers to meet specified flotation performance criteria.

Jan 1, 2001

The National Mining Hall of Fame and Museum (NMHF&M) will induct its the 2014 National Mining Hall of Fame Class on Sept. 13, 2014 during its 27th Annual Induction Banquet and Ceremony at the Westin Hotel in Denver, CO. Representing the domestic and worldwide metal production, education, and health and safety sectors of the industry, this year?s four inductees cover a diverse cross-section of the mining industry. Harry M. Conger III, Günther Franz (Frank) Joklik, Ellen Swallow Richards and Dr. Alfred Weiss will join 223 other mining industry pioneers when they are formally inducted into the National Mining Hall of Fame. They were selected for being visionaries, leaders and ambassadors, both within their own sectors and across the industry at large. Conger was a great role model and strong advocate within Homestake Mining Co. and among his industry peers on behalf of environmentally responsible, safe, profitable and high-performance operations. As chairman and chief executive officer, Conger was instrumental in revitalizing and rebuilding Homestake into an industry leader in technological advances and environmental protection. Through his contributions in exploration, project development and operations management as Kennecott president and chief executive, Joklik did much to strengthen Kennecott as a company and assisted in restoring the competitiveness of the U.S. mining industry. Richards is generally recognized as the founder of ecology. She was the very definition of a pioneer in such diverse fields as chemistry, geology and mineralogy, mining and metallurgy, environmental science, public health, home economics and education. Weiss was a true visionary in using quantitative methods and digital computers to aid mineral exploration, plan and design mines, operate mineral production facilities and integrate the disparate information resources throughout a mining company into a modern management information system. NMHF&M Board of Directors Chairman, Paul C. Jones, said, ?Again this year we are honored to be able to induct an outstanding group of deserving individuals who have made exceptional contributions to the mining industry in the United States. Included are two living inductees who have made significant contributions to management in the industry. One inductee was the first female graduate from the Massachusetts Institute of Technology, its first female faculty member and the first female member of AIME who had an outstanding career as a mineral investigator in the United States. Another inductee was a lifetime innovator in bringing digital technology into common use in our industry. Each of our 2014 inductees made significant and lasting contributions to our industry and are well deserving of becoming a member of the National Mining Hall of Fame.? The Hall of Fame Induction Banquet and Ceremony is a marquee event for the National Mining Hall of Fame and Museum each year. The 27th Annual Induction Ceremony and Banquet will be held at the Westin Hotel in Denver, CO on Saturday, Sept. 13, 2014. For banquet reservations, contact the NMHF&M office at 719-486-1229. More information is available on the NMHF&M website at www.mininghalloffame.org.

By F. Shigeyoshi

The development of pelletizing during the last ten years has continued, however, self-fluxing pellets have not been regularly and commercially produced for use in blast furnaces, except as Kobe Steel, Ltd., Japan. This paper tells about unique developments for self-fluxing pellets, and their effects when used in Kobe Steel's No. 3 blast furnace at the Nadahama Works (inner volume 1845 Nm3, hearth diameter 9.5 m)., Several phases of the pelletizing process are discussed individually, and also their relation to performance in blast furnace operation. Special emphasis is placed on proper preparation of the limestone added to the raw materials, and indurating at optimum conditions. Means of improving pellet quality by correct control of size distribution of the raw materials used in pelletizing, and indurating temperatures, are also discussed. As basicity (CaO/SiO2) of pellets increased 0. 1, coke consumption decreased 3. 8 to 4. 2 kg per ton of hot metal, when using 70% pellets in the iron burden.

Jan 1, 1969

By J. Drelich

An improved experimental procedure to measure contact angle has been consolidated with coal surface preparation involving polishing with abrasive paper, alumina powder, and a cloth, followed by ultrasonic and mechanical cleaning. Specifically, the captive-bubble measuring technique has been compared with the sessile-drop technique and the former has been recommended for the examination of the hydrophobic properties of coal surfaces. Results of the research program, which is currently under way, on the examination of the effect of the nature, amount, size and distribution of mineral inclusions in coal on its wettability are briefly reviewed.

Jan 1, 1999

By Y. J. Wang

The selection of a shaft size for ventilation purposes is a classic problem of concern to mining engineers. This presentation is concerned with the sizing of conventionally-sunk circular shafts with concrete or shotcrete linings. Costs of sinking shafts of three different depths (from 500 feet to 1000 feet) and six different diameters (from 14 feet to 24 feet) were obtained through questionnaires to shaft contractors. The primary objective of the economic model presented is the balancing of detailed annual capital and operating costs to achieve the minimum overall cost of the shaft installation over its life. The economic model is similar to previous analyses but treats several of the individual cost categories in an updated fashion. Included in the paper is a detailed analysis of the effects of varying power costs on optimal shaft size. Also included are a statistical analysis of current shaft costs and comments on the choice between shotcrete and concrete linings.

Jan 1, 1977

By C. A. Rowland

Wet grinding rod mills have been used for 50 years to grind ores and to make specification sand. The application of wet grinding rod mills is well understood. Until recently, there have been very few installations of dry grinding rod mills. The basic principles learned from wet grinding rod mills that were used in the application of dry grinding rod mills are 1. It is possible to extrapolate the performance of 5' and 6' diameter wet grinding rod mills into larger diameter rod mills with the larger mills performing as predicted. Wet grinding rod mills as large as 14' diameter (inside shell) by 20' long using 19.5' long rods are in use operating satisfactorily. 2. Wet grinding rod mills generally grind more efficiently when the fines are left in the mill feed than when the fines are removed from the feed. 3. Wet grinding rod mills produce little tramp oversize and generally can be operated in open circuit except when very close control on the top size in the product is required. When operated in closed circuit, the circulating load is normally less than 100%. 4. The power required for the desired grind can be accurately determined from the work indices obtained from rod mill grindability tests on the material to be ground. Where required it is necessary to, apply inefficiency factors for oversize feed and for larger or smaller than normal- ratios of reduction. Recent applications for rod mills have developed where it is required that dry grinding be used. These recent applications cover the grinding of 1. Lead sinter, lead slag and limestone. 2. Iron ore. 3. Silica for making glass sand. 4. Cement clinker. 5. Coke.

Jan 1, 1968

By B. Law, M. Menabde, B. Baird

Blasor is a new mine planning tool which is being used in the long and medium-term optimization of multi-open-pit operations throughout BHP Billiton’s Base Metals and bulk commodities portfolio. It is not just a scheduler, nor even only a schedule optimizer—although this function lies at the heart of the tool’s functionality—but a pit development plan optimizer, used from ultimate pit design and process plant capacity sizing right through to mining phase design and optimal panel scheduling. The tool uses a mixed-integer-linear-programming optimization engine to determine when material should be excavated and where it should be sent to optimize discounted operating cash flow over the life of operation. The core software design concept of Blasor is to provide a tool which is intuitive and flexible enough so that a competent mine planner can perform a pit development plan optimization without assistance from optimization specialists. To this end, a generalized graphical user interface has been implemented which allows full configuration of the optimization problem, including the definition of all inputs and constraints, specification of the material flow topology, bin and destination class definitions and full specification of the economic model encompassing prices and costs. This paper describes the capability of Blasor and outlines the design concepts underlying its design philosophy.

Jan 1, 2007

By Magnus Ericsson

The unexpectedly quick recovery in world crude steel production in the second half of 2009 was due almost entirely to increased production in China that began in late 2008. Previous peaks in monthly production in China were matched by April 2009. The rest of the world had still not reached pre-crisis production rates by May 2010. Chinese production drives growth, but there has been some growth in most other larger crude steel producing countries as well, compared to production in 2009. If the production rate of the first four months of 2010 continues, the total output of crude steel in 2010 will be somewhere around 1,410 Mt (1.5 billion st), the same as in the record year of 2007.

Jan 1, 2010

By L. G. Hagenbuch

Several factors need to come together in creating an integrate mining equipment dispatching system. At the hub of these factors ace the central dispatching formulas. This paper details the development of these central dispatching formulas and explores the combining of these formulas with other elements to create an integrated dispatching decision. WHY DISPATCHING? Truck dispatching implies and in reality should equate to mine equipment efficiency. Good truck dispatching will yield good mine equipment efficiency while poor truck dispatching will yield the alternative. Truck dispatching can either be automated through a computerized, process or it can be manual. Every mine with haul trucks has a truck dispatching system whether it is recognized or not. Even a system wherein the hauler operators determine where they are going for their next load is a truck dispatching system.

Jan 1, 1987

By Don L. Deardorff

The Deserado Mine and transportation system is the fuel supply portion of the Bonanza Power Plant project. Deserado Mine con¬sists of an underground mine with a capacity of 1,224,700 tonnes (1,350,000 tons) of clean coal per year, a 649 tonne (715 tons) per hour closed water circuit jig type preparation plant, a 5.6-kilometer (3 ½ -mile) overland conveyor with covered slot storage, a unit train rail load-out and 59.5 kilometers (37 miles) of totally independ¬ent, captive electrified railroad. Planning and exploration started in March of 1978. Construction of all facilities was completed in April of 1984, approximately six years after initial planning was commenced. This paper will discuss exploration, environmental permitting, mine planning, engineering and construction of the Deserado Mine project.

Jan 1, 1984

By T. R. Ellis

Regulation of mineral property valuation methodology by governments and others is due to frauds, condemnation and takings, banking industry problems, and litigation. Definitions of "reserves," "resources," and "qualified person" continue to evolve, along with guidelines to the data and disclosure required to support valuations. A less recognized but vital issue relates to the regulatory acceptability of alternatives to the comparable sales method. Comparable sales generally work well for surface real estate, and sometimes for precious metal deposits, but not at all for most industrial mineral properties. Alternative methods, such as net present value, or a geoscience rating system, often provide better valuations. Yet US regulations dictate comparable sales as the preferred method. The task of convincing regulators of the inapplicability of comparable sales to mineral properties, particularly those lacking reserves, may be as important as the valuation itself.

Jan 1, 1999

By George Hope, Edward H. Smith

In late 1989, LAC Minerals purchased 65% of Bond International Gold and as a result became controlling shareholder of the El Indio Mine through Bond and San Jose. El Indio is a world class, complex sulphide gold deposit located in the hydrothermal alteration belt of the Andes mountains in the 4th Region of Chile. The mine is located in the high Andes about 185 km east of La Serena at an elevation of 4000 meters. The 1450 workers at El Indio live in the mine camp at 3200 m and on days off are bussed to La Serena. The El Indio mine was started in 1979 by St. Joe Minerals Corp., bought by Bond in 1987 and subsequently by LAC in 1989. The mine has produced 2.7 million oz. of gold, 9. 5 million oz. of silver and 170,000 t of copper since start of operation. The mill is currently operating at a rate of 2850 t/d and producing a copper/gold concentrate which is roasted to produce a copper/gold calcine and high quality, saleable crude As203• A small proportion of the precious metals are also produced as bullion from the leach circuit. Total production during 1989 was 224,197 ounces of gold, 1,309,342 ounces of silver and 26,968 tonnes of copper. The average cash cost of production for the period was U.S. $96 per ounce of gold, net of by-product credits. The average realized price was $5.30 per ounce of silver and $1.14 per pound of copper.

Jan 1, 1990

Critical safety tools to locate miners underground are featured by several exhibitors at MINExpo. Communication was the buzzword for health and safety products at the 2008 MINExpo, and it is still important in 2012. Products unveiled following the Miner Act in 2006 have been upgraded and improved. Saving lives and reducing injuries through better leadership, planning and practice is the goal of every mine professional.

Jan 1, 2012

By J. W. Cash

The mineralogy and textures of cyclone dust, sludge, and occasional build-ups in the American Iron and Steel Institute (AISI) direct iron making pilot plant at Universal, Pennsylvania have been studied by reflected light, transmitted light, and cathodoluminescence microscopy, and phase compositions have been determined by SEM-EDS. The cyclone dust consists of particles of carbon, metallic iron, sulfur-bearing iron, and wustite. Measurements of particles in the sludge indicate that 69% are less than 2.5 µm across, 21 % are 2.5-5 µm, and 10% are larger than 5 µm. Mineralogically the sludge particles are mainly carbon and metallic iron, with minor wustite and sulfur-bearing iron. Build-ups that sporadically develop in the furnace consist of olivine, hercynite spinel, metallic iron, wustite, pyrrhotite, pseudobrookite, akermanite-ferroakermanite and gehlenite. The microtextures shown by the build-ups indicate that much of that material has precipitated at the build-up loci. This study has been supported by AISI and the U.S. Department of Energy.

Jan 1, 1995