Search Documents

By Jim Richards, Eli Choueiry, Brett Robinson, Amanda Elioff

The Los Angeles Metro Gold Line Eastside Extension (MGLEE) extends Metro’s light rail system to the densely populated and growing East Los Angeles communities. Much of the 6 mile alignment consists of at-grade track, but the project also features a1.7 mile underground segment in cut-and-cover and twin-bored tunnel structures. In light of past experiences with open shield construction, The Metropolitan Transportation Authority (Metro) specified, for the first time, use of Pressure Face Tunnel Boring Machines (TBM’s) to advance tunnels through soft ground. This paper describes the history of the tunnel design, construction management, and construction methods adopted that resulted in successfully completing the tunneling segment.

Jan 1, 2007

The inquiry into the explosion at the Moura No. 2 Mine in August 1994 recommended -?Emergency procedures should be exercised at each mine on a systematic basis, the minimum requirement being on an annual basis for each mine.? (Windridge et al. 1996). In December 1996 the ?Approved Standard for the Conduct of Emergency Procedures Exercises? was published and has been subsequently revised (Queensland Department of Mines and Energy Safety and Health Division 1999). This document provided guidelines for conducting mine site emergency exercises as well as the requirement for a test of state-wide emergency response by holding a Level 1 Mine Emergency Exercise at one mine on an annual basis. From 1998 to date (January 2008) ten Level 1 Mine Emergency Exercises have been held in Queensland, Australia. This paper discusses each of the exercises conducted to date as well as the logistics, scenario preparation, planning and organising required to conduct emergency exercises at this level.

Jan 1, 2009

A large lab apparatus was designed using a scale-down methodology based on the design legacy of the current FLSmidth commercial forced air flotation machines. This new apparatus, along with a new test methodology, was used to evaluate new rapid prototype concepts. The apparatus was designed to monitor bubble size, power, pumping capacity, Jg, velocity profiles, froth character, and tip speed. The methodology developed follows a sequence that goes from hydrodynamic tests and solids suspension tests to a flotation kinetic test. This methodology has been demonstrated to be a good tool to determine the effect of machine design changes on flotation.

Jan 1, 2012

By Peter Chou, Pooyan Asadollahi, Danny Lin

To maintain flexibility and ductility of tunnels crossing active faults, various mitigation measures are being utilized depending on fault offset movements and seismic design criteria. Examples of those approaches are simple bell and spigot joint, articulated joint, and complex deformable longitudinal bolt and spring joint system with seismic isolation washer. This paper presents a summary of tunnel fault crossing mitigation approaches and design considerations using previous relevant experiences in California as well as case histories from Japan, Taiwan, Turkey, Greece, and Italy found in literatures. Comparisons are made between large and small diameter tunnels, transportation, and utility tunnels, as well as bored, mined and cut-and-cover tunnels. Recent innovations, such as Japanese and Italian techniques, for tunnels crossing active faults are also discussed.

Jun 13, 2021

By Scott G. Britton

Microcomputeranalysis has long been a technique for engineering professionals to improve the theoretical and practical design of continuous mining systems. Such work has been typically composed of modeling observed events and then introducing a variety of known elements with predicted results to compare against the results of the model. Programs written in BASIC, Cobol, Fortran or other language dominated such efforts. These programs have taken years to develop and prove out. This article explores a new management tool used daily at Tanoma Mining Co. (TMC) to track and improve continuous mining systems through the use of microcomputers and Lotus l-2-3 software. Data provided by section foreman, shift foreman, and maintenance personnel are analyzed against predetermined goals. In this way, new production targets are developed, weaknesses in the current mining systems are identified, and the results of changes are measured. The current results of this system on the productive output of TMC systems is on the order of 10% improvement. Thin seam coal mining is an industry within the broader industry of coal mining. Thin seam mining faces the same cost pressures and engineering problems as its higher-seam competitors without the advantages of moving volume per foot of extracted material to stay at an economic parity with others requires additional creativity within the management teams to extract higher productivity gains from the existing workforce and mining systems. TMC operates a deep mine in Indiana bounty, PA, about one hour northeast of Pittsburgh.

Jan 1, 1991

By T. S. Bomar, C. J. Wood

Heavy media cyclones (HMCs) are efficient, high-tonnage devices suitable for upgrading run-of-mine coal in the 50 to 0.5 mm size range. Unfortunately, industrial HMC circuits are often not optimized due to problems such as incorrect operating pressures, poor feed distribution, excessive media contamination, mismatched components, and improper density control. To avoid these problems, operating guidelines have been provided in this article that are useful for optimizing the performance of HMC circuits. The validity of these guidelines has been assessed by means of density tracer tests carried out at several coal preparation plants.

Jan 1, 2002

By B. G. White

Traditional interpretations of vein ore deposits in the Coeur d' Alene Mining District, such as the view that these deposits formed in a transcurrent tectonic regime during the Precambrian, are being supplanted by the view that the deposits (1) formed in low-grade metamorphic shear zones similar to those that host an important type of gold deposit, (2) display features, such as wall rock carbonate zoning and vein zoning, that are common to ore deposits elsewhere, and (3) are probably Mesozoic and possibly related to emplacement of the Idaho batholith. In recent years, new interpretations have led to major ore discoveries that are likely to extend the life of the district for decades.

Jan 1, 1998

By Steven B. Van Kouteren

Value added is a loosely used qualifier in the industrial minerals industry. What exactly does it mean? What does it take to make a value-added product? More importantly, how does a company maintain the value added to its products? Most people agree that value-added means the value of a mineral minus the cost to produce it. This is misleading, though, because producing value-added products does not necessarily guarantee the profitability of the products. In some cases, firms that make value-added products are not very profitable. It is important not only to understand how to make a value-added product but also how competitive forces in the market can erode the value added. Therefore, when looking at value-added opportunities, producers must understand how to obtain the value added and how to maintain that value. Four major factors limit a company's ability to add value to its products. This paper examines these factors. It uses the ground calcium carbonate and mica industries as examples.

Jan 1, 1990

The 28th annual American Mining Hall of Fame Awards Banquet and fundraiser sponsored by the Mining Foundation of the Southwest will be held at the Marriott University Park Hotel, Tucson, AZ on Saturday, Dec. 4, 2010. The Mining Foundation of the Southwest is a nonprofit organization whose objectives are public education about the mineral industries, and recognition of outstanding accomplishments in and contributions to the fields of mineral and fuel resources. Funds are being raised to the support the foundation?s educational programs. Among these is the Educational Outreach Program operated jointly by the foundation and the Arizona Department of Mines and Mineral Resources.

Jan 1, 2010

By S. Dixon

The Peñasquito deposit in Mexico is one of the largest grassroots precious metal discoveries developed in recent years. Goldcorp Inc. acquired the gold-silver-lead-zinc property with the acquisition of Glamis in 2006. The Peñasquito property is located in the northeast corner of Zacatecas state, Mexico. The elevation of the property averages 1,900 m (6,200 ft) above sea level. It is situated in a wide east-west valley. Minera Peñasquito, S.A. de C.V., wholly owned subsidiary of Goldcorp Inc. has operated twin SABC-flotation lines since June 2010. Each line is capable of processing 50,000 tonne per day using a SABC grinding circuit followed by flotation to produce lead and zinc concentrates. The addition of a Polysius Polycom HPGR 2417 with dual 3,000 kW drives to reduce the crushed pebbles produced by the SAG mills was planned to increase production to 65,000 tonne per day per line. The production has been limited to 100,000 tpd due to operating issues in the grinding circuit. The operating issue has been the amount of pebbles generated by the SAG mills is significantly less than originally planned. This paper describes the planned installation of a crushed augmented feed to maximize utilization of the HPGR capacity. This coupled with full utilization of the SAG and Ball Mill available energies there is the potential to achieve a 50% total capacity increase from the grinding circuit.

Jan 1, 2012

By R. Gunda

Due to the rapidly increasing production rates and deepening of mine working areas, there is a drastic rise in the number of thermal issues to be addressed for maintaining a safe mine environment. As high temperatures and humidity in underground mines could affect the health and performance of workers, and ultimately the production rate, it is necessary to provide a properly controlled safe environment. The backfilling of stopes in metal, non-metal mines results in different thermophysical properties for the hanging, side and foot walls, modeling of which is not provided by any existing mine climate simulation software. This paper presents the modeling of such a single stope using the MULTIFLUX (MF) software, developed at University of Nevada, Reno. A special case is presented in this paper, where a case study from the Homestake mine in the US with a drift and ramp connected to a stope with high Virgin Rock Temperature (VRT) and various spot heat sources is modeled in MULTIFLUX and CLIMSIM, and the results are compared against each other. Another case is presented in which the stope of the previous cases is modeled with walls, each having a different set of thermophysical properties. These results are compared with the former results to analyze the effect of anisotropic properties.

Jan 1, 2011

By Christian Maguire

Tunnel contracts in New York have in recent years had few bidders with the bids received being much higher than anticipated. Since 9/11, security has become a key issue in planning key infrastructure projects in New York. This is especially true in the case of large water supply tunnels. Striking the right balance between cost and security was the major factor in determining the best configurationfor the Kensico-City Tunnel. This paper outlines the efforts made to determine realistic probable bid costs for the tunnel contracts, and the innovative approaches taken to deal with security issues.

Membrane technology has been available for over 36 years, but has been used sparingly in the general mining industry. However, recent developments in polymer chemistry, spiral wound element construction, pretreatment equipment and techniques and an expanded understanding of membrane fouling and cleaning techniques have dramatically improved the reliability and robustness of membrane based systems in the mining industry. Harrison Western has expanded the use of this “new” technology to enhance the use of membrane technologies to separate metals from large volume heap leach mining solutions containing copper, zinc, and iron, gold or silver. Moreover, membrane technologies are ideally suited to fractionations that add value to processing fluids from refineries like separating metals from acids or concentrating acids and producing high quality process fluids. Finally, wastewater from Acid Mine Drainage (AMD) or, as in the case of the Newmont Yanacocha Mine in Peru, the treatment of excess barren leach solution created during the rainy season, can be cost effectively processed to meet World Bank Standards for surface discharge. Polymeric membranes, specifically thin-film composites, have been developed that will purify, fractionate or concentrate gold, silver, copper, zinc or nickel. Recent applications have been developed for spiral wound modules that operate across the pH spectrum from 0 to 14. Systems using membranes have been constructed that operate on feed streams from 140° C to 300 centipoise. Opportunities exist to apply membrane technology to concentrate gold, silver, copper, zinc or nickel using thin film composite membranes. Engineered membrane types can operate across the spectrum from low pH (<2) acid applications to high pH > 10 cyanide applications. Incorporating HW EMS™ membrane technologies into current mining operations could allow one to increase production because the membrane technology would be used to pre-concentrate heap leach solutions, and therefore, increase utilization of existing extraction and refinery capabilities.

Jan 1, 2007

By Wilhelm Knickmeyer, Johannes Henneke

PREFACE For about 1 year Bergbau-Forschung GmbH, central research institute of the German Coal Mining Industry, undertakes full size tests for waterjet assisted tunnel¬boring in German coal mines (Fig. 1). These tests are performed with a tunnelborer of 2.6 m diam in an upper [ ]

Jan 1, 1979

By A. Mahmoudkhani

There has been a continuous interest in chemical aids for processing Canadian oil sands by hot water extraction process since the first commercial industry operation in 1967. Several inorganic and organic chemical systems have been introduced, of which sodium hydroxide is the most widely used extraction process aid by major producers. Use of NaOH, however, results in accumulation of sodium ions in recycled water, causing higher clays dispersion and producing tailings with poor geotechnical properties that turn into mature fine tailings. This is especially true for low grade and oxidized ores, which present the greatest challenges in bitumen recovery and produce the major portion of fine tailings. In this paper, we are presenting a novel method based on use of inorganic polymers as process aids for various low grade oil sands ores. Denver flotation cell and a laboratory scale hydrotransport loop were utilized to evaluate the effect of chemical dosage and operating parameters on the processability of oil sands samples from Athabasca region. Process tailings were examined for properties such as water chemistry, suspended solids, settling rate and the ease of tailing treatments. Our results demonstrate that the use of inorganic polymers during the froth process lead to a significant improvement in bitumen recovery from low grade oil sands and can improve further tailing treatments. This offers a viable solution that can be easily incorporated into current processing facilities and deliver several operational and economical benefits. Advantages in use of inorganic polymers versus sodium hydroxide are presented in details.

Jan 1, 2012

By M. H. Basiri

The application of aluminum matrix composites, due to their unique properties, is significantly growing in the variety of industries such as aerospace and automobile. In comparison to other light metals, such as magnesium and titanium, aluminum is lower in price. These are the advantages that this metal dominates the others. In this research, first by applying the lost foam casting method, the SiCp/A356 composite was cast in the bottom and side gate conditions with 690°C and volume fraction of 10%. Furthermore, the effects of reinforcement particles (60 µm, 75 µm) were examined. The results present the particles distribution in the side gate methods is more homogeneous than the bottom gate casting method. Also, by increasing the particles sizes, the fading rate in the side gate are reduced from 22% to 19%, as well as from 26.4% to 25.4% in the bottom gate. Key words: Carbide-Silicone Particle, Gating System, Composite Micro-Structure, Foam Casting

Feb 27, 2013

By S. K. Gilman

Zircon (ZrSiO4) sand production of about 1.1 Mt/a(1.2 million stpy) predominates the global supply of zirconium minerals. Baddeleyite (ZrO2) contributes less than 1 percent of supply. Zircon is almost exclusively produced as a co-product from the mining of titanium minerals, mainly from mineralized beach sands. In 2004, there were a number of new projects under consideration that were more dependent on zircon revenue than for titanium minerals. This reflected sustained higher zircon prices and forecast ongoing supply shortages in the absence of major new discoveries.

Jan 1, 2005

By S. Addie

In the early 1990’s the British Columbia (Canada) mineral industry frequently discussed the need to participate in, and compromise with, public environmental interests in order to ascertain long-term stability. However, as the decade progressed the mineral industry withdrew from almost all meaningful public participation. As government protected areas policy in the past year has illuminated, there is a continued need for long-term land access stability. This paper historically analyses the public engagement policies of the British Columbian mineral industry while it participated in long-term consensus-based multi-stakeholder land-use planning processes. From this analysis the paper recommends that the mineral industry reengage the public and institute a new working relationship with environmental advocacy groups so as to ensure British Columbia becomes the most sustainable mineral producing jurisdiction in the world.

Jan 1, 2011

Characterization of ore and waste-rock material using automated quantitative micro-mineralogical techniques (e.g., QEMSCAN® and MLA) has the potential to complement traditional acid-base accounting and humidity cell techniques when predicting acid generation and metal release. These characterization techniques, which most commonly are used for metallurgical, mineral-processing, and geometallurgical applications, can be broadly applied throughout the mine-life cycle to include numerous environmental applications. Critical insights into mineral liberation, mineral associations, particle size, particle texture, and mineralogical residence phase(s) of environmentally important elements can be used to anticipate potential environmental challenges. Resources spent on initial characterization result in lower uncertainties of potential environmental impacts and possible cost savings associated with remediation and closure. Examples illustrate mineralogical and textural characterization of fluvial tailings material from the upper Arkansas River in Colorado.

Feb 27, 2013

By R. B. Crookston

This paper presents the status and mining method chosen by each of the active underground oil shale projects in the united States today. Potential improvements in equipment and methods on the near-term horizon are discussed. The problems and potentials that lie in the long-term future of oil shale mining are examined in light of the demands which must be met by this developing technology.

Jan 1, 1981