Search Documents

By A. McGarr

The shear stress t that can be sustained by the rock mass in the environs of a mining-induced earthquake controls the near-fault peak ground velocity v of that event according to v=0.25(ß/G)t, where ß is the shear wave speed and G is the modulus of rigidity. To estimate t at mining depths, I review the results of four studies involving Witwatersrand tremors that relate to the bulk shear strength. The first and most general analysis uses the common assumptions that the seismogenic crust is pervasively faulted, has hydrostatic pore pressure before mining, and an extensional stress state that is close to failure. Mining operations reduce the pore pressure to zero within the mine and redistribute the stresses such that, in localized regions, the state of stress is again at the point of failure. Laboratory friction experiments can be used to estimate t in the zero-pore-pressure regime. Second, model calculations of states of stress in the vicinity of mining at about 3 km depth indicated the shear stress available to cause faulting near the centre of a distribution of induced earthquakes. Third, laboratory experiments combined with microscopic analyses of fault gouge from the rupture zone of a mining-induced event provided an estimate of the average shear stress acting on the fault to cause this earthquake at a depth of 2 km. Fourth, moment tensors determined for mining-induced earthquakes usually show substantial implosive components, from which it is straightforward to estimate t. These four different analyses yield estimates of t that fall in the range 30to 61 MPa which implies that near-fault particle velocities could be as high as about 1.5 m/s. To the extent that the causative fault ruptures previously intact rock, both t and v, in localized regions, could be several times higher than 61 MPa and 1.5 m/s.

Jan 1, 2002

By A. Sariisik

This study analyses the results of a pilot trial of a newly developed armed-chained stone-cutting machine. The machine was developed in Turkey and trialed at the Kaklik/Kocaba travertine quarries in the Denizli District. An armed-chained cutting machine is an alternative to the diamond wire cutting method more frequently used in the production of natural stone quarry blocks, and increases production efficiency and quality. Since there is no need to collapse the blocks using the armed-chained cutting production process, there is no risk of the block developing cracks. This results in a considerable increase in the efficiency of natural stone block production. The armed-chained cutting machine is easier both to assemble and run when compared to other block cutting methods. This process resulted in the production of a larger number of blocks at a lower cost within the same time frame, particularly in travertine quarries and in all other natural stone quarries. The block efficiency in travertine quarries was calculated as 65?80%using the armed-chained cutting machine, compared with 7?14% using the normal diamond wire cutting method.

Jan 1, 2010

By Simon St J Tose

The objective of this paper and presentation is to review the different criteria and methodology used by AEL and other organisations to create a pre-split design which delivers a stable highwall for the life of that part of the mining operation. It will look at the need to adapt and change the way, size and direction of the production blasts as the mining phase approaches the highwall position for which a pre-split has been created. Key Words: Pre-split: Design; Highwall; Perimeter

Jan 1, 2006

By M. A. Kujoana

Following on the design of good mining layouts and regional support systems, and the implementation of sound strata control practices, stope support is the ultimate strategy to combat the hazards of rockfalls and rockbursts. The primary function of stope support in intermediate and deep level mines is to stabilize the rock mass immediately surrounding stoping excavations, that is, the zone of fractured rock which behaves in elastically around stopes. Support design is a process resulting in a support system which is both practical and meets or exceeds by a factor of safety the requirements for a particular geotechnical environment. The aim of this project was to design a support system, which accommodates the factors of rockfalls and rockbursts. The pack support unit must be easily handled, less costly and can be used in stopes without any significant convergence. The project tested the structural stability of packs to their expected deformation, in order to design a height to width ratio for stopes where little convergence is expected.

Jan 1, 2009

By A. K. Anyimadu

Ongoing development work on ultra-fine grinding for various applications at the Group?s concentrators has been conducted by Anglo Platinum over the last few years. Current potential applications for mainstream grinding and concentrate grinding are the subject of a group-wide research and development programme. The first 10 000-litre 2.6 MW IsaMill was jointly developed by Anglo Platinum, Xstrata Technology and Netszch for installation at the Western Limb Tailings Re-treatment project in Rustenburg, South Africa. The unit was commissioned in late 2003/early 2004,and has operated in an intermediate concentrate regrind application successfully since. This paper describes the operational performance to date, as compared with the original duty specifications and objectives. The first mainstream M10 000 IsaMill with a 3 MW drive will be operational in November 2006 at the Potgietersrus Platinum (PPL) ?Platreef? Sandsloot Concentrator in South Africa?s Limpopo Province. Keywords: Western Limb Tailings Re-treatment Plant, IsaMilling, Platreef, platinum, palladium, PGMs, tailings.

Jan 1, 2007

By J. Morkel

During research on mainly the weathering of kimberlite, it became evident that its mineralogical composition is an important factor in the complex process of physical and chemical disintegration. The mineralogy of tuffisitic kimberlite breccias from two localities, the Cullinan and Venetia mines, is compared with special reference to the occurrence of associated clay minerals. The clay mineral composition influences the engineering properties of these rock types. It is illustrated how the presence of swelling clay components can be confirmed by ethylene glycol treatment and chlorite minerals by heat treatment using X-ray diffraction. Smectites are present in both tuffisitic kimberlites, dominant at Venetia while chlorite is more frequent at Cullinan. More tuffisitic kimberlite breccias samples from venetia were also characterized. It was found that kimberlite disintegration is correlated with the presence and abundance of smectite.

Jan 1, 2006

By J. W. van der Merwe, A. Palazzo

"Owing to the corrosiveness of the untreated brackish cooling water typically used for steel mills (and other environments), it is important to treat the water and monitor corrosion in such systems. Generally, corrosion rates are monitored with corrosion probes inserted into a pipeline or vessel. This has been standard practice for many years, and is widely accepted in industry. Typically, two kinds of probes are used - electrical resistance and linear polarization resistance (LPR) probes.In this study, the effectiveness and accuracy of the LPR technique was evaluated by comparing the electrochemical measurements with the results of mass loss tests using corrosion coupons. The corrosivity of the environment, a synthetic brackish water, was varied by varying the calcium hardness and alkalinity, and to simulate actual plant conditions temperatures of 35°C and 45°C were used. In addition to the corrosion rate measurements, the iron concentration was measured, as well as the imbalance from the probe.The corrosion rates obtained by LPR were from 57% lower to 385%higher than those from the immersion tests. Most probe measurements were higher than the immersion results, and 50% of the probe results were50% or more higher than the immersion results. The best correspondence between the two methods was obtained at low calcium levels, except for one measurement that was 93% higher than the coupon results. There was no clear correlation between parameters such as temperature and total alkalinity and the difference between the results. It would therefore appear that LPR measurements can differ significantly from immersion results, and LPR results should therefore be used with caution in industrial applications."

Jan 1, 2015

By A. K. Anyimadu

Ongoing development work on ultra-fine grinding for various applications at the Group?s concentrators has been conducted by Anglo Platinum over the last few years. Current potential applications for mainstream grinding and concentrate grinding are the subject of a group-wide research and development programme. The first 10 000-litre 2.6 MW IsaMill was jointly developed by Anglo Platinum, Xstrata Technology and Netszch for installation at the Western Limb Tailings Re-treatment project in Rustenburg, South Africa. The unit was commissioned in late 2003/early 2004, and has operated in an intermediate concentrate regrind application successfully since. This paper describes the operational performance to date, as compared with the original duty specifications and objectives. The first mainstream M10 000 IsaMill with a 3 MW drive will be operational in November 2006 at the Potgietersrus Platinum (PPL)?Platreef? Sandsloot Concentrator in South Africa?s Limpopo Province. Keywords: Western Limb Tailings Re-treatment Plant, IsaMilling, Platreef, platinum, palladium, PGMs, tailings.

Jan 1, 2007

By Darelle T. Janse van Rensburg

Some of the more recent developments in Paint Technology are solvent free materials. These coatings have mainly been formulated to overcome the negative attributes of solvent-based coatings, i.e. environmental, safety and health risks, potential for solvent entrapment and osmotic blistering, as well as the formation of micro-pores during the curing process. Two solvent free liquid epoxy coatings have been used extensively on power generation plant. However, very little is known regarding their long-term performance under different exposure conditions, as well as whether these coatings actually perform better than their solvent-borne counterparts. In addition, solvent free materials are generally used where outage periods are restricted and coatings need to be applied within a very short period. Though these materials have reportedly much shorter curing times than other conventional solvent-borne coatings, little is known regarding their limits with respect to maximum film thicknesses and being put into service while still being wet/partially uncured. The latter has become common practice at many power stations in the past two years or so. In addition, the application and curing methods of solvent free materials are different to that of solvent-borne materials, and may require equipment and application process changes. This paper covers the application and performance properties of solvent free coatings in comparison to solvent-borne materials primarily intended for immersion service. Numerous coatings were evaluated under immersed static and cyclic hydrostatic pressures. Other tests included short curing / early immersion tests, dry-to-touch and dry-through curing times, adhesion tests, surface tolerance tests, etc. The results show that the solvent free materials have clear benefits with respect to safety, health, environmental and long-term performance, but will be more difficult to apply compared to solvent-borne materials.

Jan 1, 2006

By J. Danoczi

Specially designed X-ray machines are used extensively on diamond mines for the recovery of diamonds from ores. These machines are extremely expensive and, at present, there are no reliable methods of determining if the equipment is performing efficiently. The objective of this work was to manufacture translucent X-ray diamond simulants, which would emit varying but known luminescence signals when exposed to X-rays. These X-ray diamond simulants could then be used to determine the efficiency of diamond recovery operations.

Jan 1, 2008

By C. Kloppers

The aim of this investigation was to reduce the cost of primary steel de-oxidation by substitution of aluminium primary de-oxidation with a practice that uses carbon. The cost of carbon is four times lower than that of aluminium. The application of carbon would directly result in raw material cost savings. Investigations were conducted at Iscor?s Newcastle steel plant on various steel grades. Specific production aspects were emphasized to ensure that the cost savings accrued would not create secondary expenses. These production aspects entailed: ?Yields on de-oxidation elements ?De-oxidation capabilities ?Alloying yields (Mn and Si) ?Carbon-pickup ?Nitrogen-pickup ?Temperature loss during tap ?Steel cleanliness ?Slag morphology. This project proved that carbon de-oxidation, apart from reducing de-oxidation raw material cost due to cheaper raw materials being used and lower consumption rates, resulted in steel that is cleaner and has lower nitrogen concentrations. Carbon primary de-oxidation has been implemented at Iscor?s Newcastle plant on a large range of steel grades, ranging from ultra-high carbon (> 0.60% C) to ultra-low carbon (< 0.03% C) grades. A net saving of between R100 000 and R200 000 per month was achieved.

Jan 1, 2001

By J. E. Nesset

The bubble size, together with the gas rate, determines the bubble surface area flux in flotation machines and, therefore, impacts directly on the kinetics of flotation. Understanding the variables that influence bubble size is one of the keys to understanding flotation recovery. Surprisingly, these relationships are poorly understood, largely due to the difficulties associated with gas dispersion measurements in industrial environments. The McGill gas dispersion sensors (bubble size, gas rate, gas holdup) are capable of reliably making such measurements. This paper reports on a study, using the McGill sensors in a 0.8 m3 Metso RCSTM pilot cell, which investigated the effect on bubble size of frother type and concentration, gas rate, temperature and rotor speed. A Denver laboratory cell was used to investigate the effect of elevation above sea level. Frother concentration proved to have the predominant influence on bubble size, and the effect of frother type can be normalised as a function of the critical coalescence concentration (CCC). Measurements made at many plant sites worldwide are compared to the model developed using the Metso RCSTM unit.

Jan 1, 2007

Analysis for pillar extraction potential (A-PEP) is an intelligent tool, which could be used as a preliminary output indicator when considering the secondary extraction of regional support pillars in the Witbank and Highveld coalfields of South Africa. The safe and economic extraction of underground coal pillars is of paramount significance and importance to the South African coalmining industry to ensure continuity of supply of this fossil fuel. Pillar extraction practices in South Africa have been responsible a significant proportion of safety and fatality statistics in relation to its relative output (less than 5 per cent of total South African coal production) and, as a result, research was undertaken in local pillar extraction operations and extended to similar operations in New South Wales, Australia to assess a way forward for pillar extraction in South Africa. It was found that, although little in the way of new technologies has emerged in this field in the recent past, significant contributions could be made in the field of risk analysis to obtain a generic design methodology for pillar extraction in South Africa. The resultant A-PEP tool to assess pillar extraction potential is based on certain physical, risk and economic factors, which combine to indicate operational success in terms of economic, health and safety attributes. At the time of A-PEP?s development there was alack of operating underground coal pillar extraction operations, which made it difficult to validate its applicability. Since then, however, A-PEP has been successfully tested and validated against two unique underground coal pillar operations, which is the discussion of this paper. One operation is situated in the Witbank coalfield and is extracting pillars, which are 20 years old and at a depth of 80 metres below surface, while the other operation is situated in the Highveld coalfield-which is extracting 6 month-old-pillars underneath a massive dolerite sill at a depth of 220 metres. A-PEP has shown that its predictive nature is consistent the workings at both operations, irrespective of their unique conditions, and as such it can be successfully used as a mine planning tool. The A-PEP mine planning tool thus represents a positive step toward an integrated approach to underground coal pillar extraction when considering legal and operational aspects, which could form the basis for legislative guidelines when considering the future of pillar extraction in South Africa.

Jan 1, 2005

By F. Bonnet, J. Lehmann, H. Gaye

A review of thermodynamic information and models of slags, including associated software when available, is presented. The pertinence and accuracy of these models is discussed by comparison of their predictions for various slag thermodynamic properties with the available experimental data. Practical industrial applications will be illustrated by a literature review of the dephosphorization process of ferromanganese alloys and by the description of Ti behavior during silico-manganese alloys production. This latter example will show how the thermodynamic models have been used to propose a flotation treatment at low temperature to enhance TiC removal.

Jan 1, 2004

By I. A. Mwamba

Plain and alloyed titanium aluminides of composition Ti-47.5 at.% Al were prepared by melting commercial-purity titanium and aluminium with additions of 1 at.% precious metal. The as-cast alloys were subjected to potentiodynamic scans in 5, 15, and 25 wt% HCl aqueous solutions at room temperature and compared for their abilities to spontaneously passivate. Addition of precious metals resulted in a general improvement of corrosion resistance by increasing the open circuit potential to more noble values. Addition of 1 at.% gold or silver to titanium aluminide did not significantly increase the corrosion potential (Ecorr) above that of the plain titanium aluminide alloy, indicating that gold and silver are not sufficient cathodic modifiers to improve the corrosion resistance of titanium aluminide in all the solutions tested. However, platinum, palladium, and iridium additions shifted the corrosion potentials to the position of the passive region of plain TiAl for all solution concentrations. This indicated that TiAl alloyed with these platinum group metals would passivate spontaneously by cathodic modification. TiAl alloyed with palladium performed the best in 5 wt% HCl solution with the most positive corrosion potential. In 15 wt% HCl solution, alloys with platinum exhibited the most positive corrosion potentials, while alloying with iridium or palladium revealed more negative corrosion potentials. Thus, palladium alloying led to the best cathodic modification of titanium aluminide in low-concentration HCl solution, whereas platinum and iridium alloying additions resulted in the best cathodic modification of titanium aluminide in high-concentration HCl solutions.

Jan 1, 2013

By G. Lyman

The cross-belt sampler is a device that is very widely used even though it has not been ratified by the Standards associations. This paper is concerned with the bias testing of two cross-belt sampler designs against stopped belt samples and a cross-stream cutter at the belt end. The bias analysis is carried out using size distribution as the analyte and conventional t-testing and the Hotelling T squared test, which are compared for their effectiveness. The paper considers the issue of detectable bias and the statistical planning of bias tests.

Jan 1, 2010

By N. Anacleto, S. Ganguly

Reduction of Groote Eylandt (Australia) and Wessels (South Africa) manganese ores using CH4-H2-Ar gas mixture was investigated in a fixed bed laboratory reactor in the temperature range 1000?1200oC. The extent and kinetics of manganese ore reduction as a function of gas composition and temperature were determined by on-line off-gas analysis using mass-spectrometer and dew point sensor. Morphology of ores and its change in the course of reduction was examined by optical and scanning electron microscopy. Phases of raw materials and reduced samples were analysed by XRD and EPMA. Manganese oxides were reduced to carbide Mn7C3. High extent and rate of reduction by methane-containing gas in comparison with carbothermal reduction were attributed to high carbon activity in the reducing gas, which was in the range 15 - 50 (relative to graphite). The reduction rate of Wessels manganese ore increased with increasing temperature. Reduction rate and extent of Groote Eylandt manganese ore achieved maximum at 1050oC. The decrease in rate and extent of reduction of Groote Eylandt ore at higher temperatures, particularly at 1150-1200oC, was due to sintering and formation of semi-liquid silicate slag. The optimum conditions for the reduction of manganese ores were established as follows: a) temperature: 1150-1200oC for Wessels and 1050-1100oC for Groote Eylandt ores, b) methane concentration: 10-15 vol%, c) hydrogen concentration: above 30 vol%, (d) size: 1-3 mm. An addition of lime (10-15 wt% CaO) to the Groote Eylandt manganese ore increased melting temperature of slag and significantly increased the rate and extent of reduction at elevated temperatures.

Jan 1, 2004

By J. Daraisme

Société le Nickel (SLN) exploits the Dôme lateritic nickel orebody at its Tiébaghi operations in New Caledonia. The site geology has an obvious bearing on recovery and metallurgical performance, and the controls are extremely complex at all scales: lithology, oxidation-reduction conditions, mineralogy, and multivariate geochemistry. In that context, establishing an adapted recoverable resource estimation method that is efficient and transparent proves an interesting challenge. The method must address the key notions of: ? Support effect: the exploration data-set can only warrant the estimation of large panels 20×20×3 m3, which are much larger than the selective mining units (SMUs) of 5×5×3 m3 ? Information effect: the selection at production stage uses estimates based on information much denser than that available for mine planning. The problem is rendered more complex in this type of deposit by the fact that the additive variables used for any estimation process (metal accumulation and ore tonnage) are not the ones used to establish the selection at mining stage (i.e. the nickel grade of SMUs, which is the ratio of accumulation on tonnage). Eventually, the selection criteria involve not only Ni grades but also other constituents such as Al2O3, Fe2O3, MgO, and SiO2. The solution presented in this paper is the construction of a platform of SMU multivariate simulations in the saprolitic horizon, together with efficient post-processing aimed at producing the multivariate recoverable resource estimates. The efficiency constraints imposed by the number of blocks to be simulated (1.5 million) lead to resorting to direct block simulations. The underlying multivariate discrete Gaussian model (DGM), the validity of which is tested beforehand, is put to good use to mimic the selection process at the mining stage, by offering the ability to simulate in each block a composite value located at random within the block. Finally, the paper presents the application of a scenario reduction algorithm to pick a representative subset of a few simulations to help appraise the risk attached to the downstream phases (reserve optimization, mine sequencing) of the project. The implementation presented here is for the first generation of the Scenario Reduction plugin built in Isatis software, where measuring the distance between the initial set of scenarios and the reduced set is based on Ni quantities only. Research is under way to adapt the measure to the true multivariate nature of the problem.

Jan 1, 2014

By M. Mostert

Mining companies sponsor a range of non-core, corporate social responsibility projects to adhere to social and labour plans and environmental management prerequisites that form part of a mining licence application. Some companies go above and beyond such projects, sponsoring initiatives that generate renewable energy through solar power, wind energy, natural gas, etc. The challenge for these companies is to choose between a variety of projects to ensure maximum value, especially in times when the economic climate might be less favourable for such projects. The focus of this research was to analyse the concept of sustainability as it exists today, and to apply that to the triple bottom line accounting method in an attempt to quantify the sustainability of a project. Research was done on the methane burn-off project at Sibanye Gold?s Beatrix Mine to establish how such projects are planned and financed, and what impact they have on the triple bottom line of a company. The financial bottom line is, by definition, one that executives understand. This paper also proposes a quantitative method for defining the social and environmental bottom lines as well. By considering the financial, social, and environmental values, the study attempts to determine a monetary value for a sustainable renewable energy project. This monetary value can be compared to similar values obtained for other sustainable renewable energy projects under consideration. The research suggests that monetary value alone is not enough to base a sustainable decision on, and qualitative measures are suggested for use in conjunction with quantitative methods. The selection method proposed should assist the board of a mining company to choose the most sustainable option and the project that will add the greatest value to the company across all three bottom lines. It will also provide increased justification for such renewable energy projects, even in periods of harsh or uncertain economic climates.

Jan 1, 2014

By C. Musingwini

The Bushveld Complex is economically significant and strategically important to South Africa, thus it is imperative that optimal extraction of platinum group metal (PGM) resources on the Bushveld Complex is achieved. Optimal extraction broadly requires that the maximum amount of ore is extracted by excavating and hauling the minimum amount of waste in the shortest possible time, at the least cost, and in the safest and most environmentally acceptable manner. In open-pit mine planning this entails among other things, minimizing the waste stripping ratio, whereas in underground mine planning it includes minimizing the metres of waste development. In conventional mining, the main development that is in waste or partly in waste and defines the mining grid pattern includes levels and raises. It was prudent to consider optimizing level and raise spacing in conventional mining because the method is a prevalent mining method on the Bushveld Complex accounting for nearly 70% of platinum production.

Jan 1, 2010