Search Documents

This paper describes DRA?s involvement with the expansions at Tati Nickel, Phoenix Mine, that have taken an initial plant design of 3.6 Mtpa (originally built by Murray & Roberts), up to 5 Mtpa, and eventually 12 Mtpa capacity. Initially, the plant could not achieve the design name plate capacity for the first few years of operation, as a consequence of the notoriously hard and abrasive nickel ore affecting primarily the operation of the crusher circuit. In order to extend the life of mine, Tati? assessed and then redefined the mining plan, choosing to increase the Phoenix mine reserves to a lower cut-off grade. In order to increase nickel units produced, the concentrator had to therefore treat additional tonnage at lower head grades. Site investigations and field tests around the comminution circuits are outlined, indicated that the milling circuit could be increased to 650 tph, from the initial design of 470 tph, for a similar feed grade and recovery. A project was initiated to debottleneck the crusher circuit and achieve the new target throughput. (Project 5M). This was followed by a feasibility study of the impact of pre-concentration by DMS, which after promising laboratory tests, was followed up with the installation of a 200 tph ?demonstration? plant. The success of this demonstration plant provided the impetus to expand the supply to the 5 Mtpa mill from a large preconcentration stage. A gyratory crusher (one of the largest and most powerful) will receive ore directly from the open pit operation, feeding into a secondary-tertiary crushing plant followed by a modular DMS preparation circuit. Four large DMS processing modules have been installed to treat the tonnage, with high expected rejection levels. Finally a review of the DMS process capability on an ostensibly disseminated micro-gabbro nickel ore is given, which shows the remarkable impact that preconcentration can have on an operation, both in terms of profitability and a successful process ?expansion?. The performance of the DMS plant has significantly extended the life of mine, allowing the mine to significantly reduce mine cut-off grades and curb its previously selective mining practice.

Jan 1, 2009

1. New books Extractionmetallurgy'81. London, Institution of Mining and Metallurgy, 1981. 441 pp. $40. Structures and properties of engineering alloys, by W. F. Smith. London, McGraw-Hill, 1981. 512 pp. R89,65. Rock and mineral analysis, by W. M. Johnson and J. A. Maxwell (editors). 2nd ed. New York, Wiley, 1981. 424 pp. $40. Mining methods and equipment, by Mining Information Services. London, McGraw-Hill, 1981. 218 pp. International directory of acronyms in library, information and computer sciences, by P. M. Vaillancourt. New York, Bowker Publishing Co., 1980.516 pp. 2. New journals Trends in analytical chemistry (TRAC), Amsterdam, Elsevier, 12 issues per year. Subs. for Volume I (16 issues) D.H 95.50. Engineering management international, Amsterdam, Elsevier, 4 issues per year. V.S. $32.50, D.H. 70.00. 3. Mineral policy sector publications Mineral Bulletin MR 188. Vanadium: an imported mineral commodity. $3.60. Mineral Bulletin MR 190. Canadian mines: 1980 perspective. $3.00. Canadian mineral survey 1980, by the staff of Mineral Policy and Energy Sectors. $1.00. 4. NIM reports Report 2090 Observations made during the dig-out of a 48 MV A ferrochromium furnace. Report 2110 The investigation of a fracture on one side of a skip bridle in a mine shaft. Report 2111 Pilot-plant tests for the recovery of chromite and the noble metals from the UG-2 Reef at Maandagshoek. Report 2112 The behaviour of UG-2 chromite concentrates during smeUing. Report 2113 M uUivariable control of a milling circuit at East Driefontein Gold Mine. Report 2115 Estimation of material variation in powdered materials Report 2116 Optimum operation of a direct-reading spectrometer with excitation by a 5 kW inductively coupled plasma torch. Report 2121 Five robust indicators of central value. Report 2124 The direct determination, by differential pulse anodicstripping voUammetry at the thin mercury-film electrode,of cadmium, lead, and copper. Report 2127 The preparation of a reference material of South African zirconium concentrate from Richards Bay. Report 2128 The determination, by differential pulse anodic-stripping voltammetry at the thin mercury-film electrode, of cadmium and thallium in six NIMROC reference materials Report 2130 The organizing of conferences. Research grant The Board of Directors of International Precious Metals Institute in conjunction with Gemini Industries, Inc., a California-based refiner of precious metals, recently announced a Gemini Research Grant of $3000 will be awarded annually to a graduate student who is pursuing studies in metallurgy, chemical processes as it pertains to precious metals, or materials sciences, and who is performing or planning research studies in the precious metals. Accidents and diseases The Third International Colloquium for the Prevention of Occupational Accidents and Diseases in the Iron and Metal Industry is to be held on 15th and 16th June, 1982, in Palma de Mallorca, Spain.

Jan 1, 1981

A prize awarded by the SAIMM for outstanding academic achievement by 4th-year and 5th-year diplomates at technikons was instituted several years ago. The Senior Vice-President, Mr J.D. Austin, accompanied by the Institute's Secretary, Mrs D. Gardner, attended a prize-awarding function in the form of a luncheon at the Hotel School of the Technikon Witwatersrand on the 25th May.

Jan 1, 1984

By F. Yang, S. S. Long

Mixed fatty acids, such as oxidised paraffin soap, are frequently used as a substitute for oleic acid in flotation of scheelite in China. Not only because it is cheaper than oleic acid, but also because it is superior in flotation performance to oleic acid. This superiority is generally attributed to the mixed fatty acids' synergistic effect. In this paper, the synergistic effect of oxidised paraffin soap was investigated. We found it mainly consists of a series of saturated fatty acid salts, with six to nineteen carbon atoms. All the contained fatty acids were classified into four groups based on their chain length to make the research work practical. Also, the groups were labelled as 1, 2, 3, and 4 in order. The research was simplified into studying the synergistic effect of four equivalent collectors, instead of fourteen fatty acids. It is justified by the fact that neighbouring fatty acids are expected to have a similar flotation performance. The synergistic effect of the four groups of fatty acids was studied by single-mineral flotation with single groups, binary mixtures, ternary mixtures, and the full component, as collector respectively. The flotation performance index and synergy value were introduced to evaluate flotation performance and synergistic effect of groups, respectively. The results show that the mixture 1+2+3 has the strongest synergy of all followed by the mixtures 1+3 and 2+3. The mixture 3+4 and 1+2, on the other hand, have negative synergy. The synergistic effect of mixtures of groups indicate that being consecutive in length and a broad range of lengths are vital for fatty acids to enhance synergy. Group 3 is fundamental for the collecting action of 733 oxidised paraffin soap in the flotation of scheelite. The fatty acid soap in group 4 is not suitable for flotation due to its low solubility. Keywords: Mixed collectors, synergistic effect, scheelite

Jan 1, 2020

By M. Saghaeian, R. Hejazi, V. Sheikhzadeha, A. H. Baladastian, A. Dehghani Ahmadabadi

This paper describes research done to remove apatite (phosphorus) from hematite ultrafine (70% finer than 25 micron) concentrate, recovered by electromagnetic separators at the FST Tailing Recovery Plant located in Chadormalu Iron Ore Complex through reverse froth flotation. As a result, iron and phosphorus content in magnetic concentrate (flotation feed) were 53.52% and 0.58%, respectively. Therefore, to increase the Fe content and decrease the P content of the sample, reverse flotation tests were applied. Chemical reagents used in this research consisted of sodium silicate as a depressant, sodium hydroxide and sodium carbonate as pH regulators, Alke & Dirol as fatty acid collectors and MIBC as frother. Process parameters including dosages of collectors, depressant and frother, preparation times of depressant and collectors, steps and time of frothing and pH range were selected. After doing flotation tests, in optimum condition, dosages of collectors were 1200 g/t, depressant 1200 g/t, pH in the range of 9.5 to 10, preparation time of collectors in the first step was eight minutes and at the other steps, four minutes; the number of frothing steps 4 and frothing time in each stage was three minutes. In this case, it was observed that the amount of phosphorus in the final concentrate was reduced to 0.05%, the Fe content increased from 53.52% to 61.66% and the Fe recovery achieved was 82.21%. Keywords: Iron ore, hematite ultrafine concentrate, iron and phosphorus content

Jan 1, 2020

By D. Das, B. K. Nandi

The present study focuses on utilising the electrocoagulation (EC) process for the treatment of process water generated in an iron ore beneficiation plant for safe discharge and reuse. Removal of heavy metals like Fe, Cr, Cu, Zn, Mn and Pb which was found in higher concentration along with some other impurities exceeding the permissible and discharge limit were attempted. The influence of different electrode material, current density, inter-electrode distance, and solution conductivity was explored for effective removal of the metal ions. Experimental results infer that almost 99.95% Fe, 97.77% Cr, 73.44% Cu, 99.34% Pb and 88.69% Mn was removed using aluminum electrodes at monopolar mode at a current density of 68.50 A/m2, inter-electrode distance of 1 cm and solution conductivity of 1.033mS after 60 min of EC. In addition, removal of other toxins like TDS, turbidity, salinity and conductivity etc. was also assessed during the process. Removal of such heavy metal ions by EC was found to follow 1st order kinetics with electric energy consumption of 3.93 kWh/m3, electrode consumption of 0.1191 kg/m3 and operating cost of 0.6115 US$/m3 respectively. Keywords: Fe removal, electrocoagulation, Al electrode, turbidity

Jan 1, 2020

By A. Rahmanab, A. Torpy, M. I. Pownceby, M. N. Zaman, N. Haque, W. Bruckard, J. Tardio

Ilmenite is the principal feedstock for producing TiO2 - used in paints, plastics and paper and the production of Ti metal. The Brahmaputra River system in Bangladesh represents a potentially new source of ilmenite concentrated within sandbar placer deposits and the current study presents results from beneficiation and characterisation studies conducted on Brahmaputra River Fe-Ti oxides. Characteristic of fluvial systems, the ilmenite concentration is low (~0.5 wt-%), however extensive annual dredging for waterway navigation provides the economic impetus to recover saleable ilmenite. The Fe-Ti oxide suite derived from magnetic fractionation comprises homogeneous ilmenite, titanohematite and hematite, although many grains exhibit complex exsolution within the (Ilm-Hem)ss series. The textural variability results in difficulty generating a pure ilmenite feedstock with the bulk concentrate typically being low in TiO2, containing 31.0 wt-%TiO2 and 62.7 wt-% (Fe2O3). Results are interpreted via an analysis of the implications for producing a commercial-grade ilmenite concentrate suitable for TiO2 production. Keywords: Ilmenite, titanohematite, Fe-Ti oxide exsolution, TiO2 production

Jan 1, 2020

By J. Botha

There are many underground mining software tools available to plan and schedule the development of underground mines. A shortfall of these tools is the optimization of the underground equipment and strategy in order to maximize the development rate. This paper will illustrate how the SimMine® software was used to maximize underground development at Petra Diamonds' Cullinan Diamond Mine. It will also determine the effect of various development strategies and equipment capacities on the underground development rate and pinpoint potential bottlenecks in the mine development cycle.

Jan 1, 2010

By S. Polansky, J. Kolacz

The new sorting system has been developed to achieve efficient separation at low mineral content levels. The system employs high resolution X-ray sensors providing multi-energy analysis, thus giving maximal information about processed materials measurable by X-ray radiography. It makes it possible to analyse the internal structure of the particles and directly detect inclusion of minerals and metals like copper or gold. The paper describes sorting application examples for zinc, lead, copper and gold ore with low metal content below 0.1% of Cu. The sorting system still allows high efficiency analysis, quantification and removal of rock particles representing waste fraction with no metal or a negligible amount being uneconomic to process. This brings a huge advantage during pre-concentration, where almost no losses of valuable minerals in the waste fraction can be achieved. The presented sorting system has been developed by Comex and X-MINE EU Project Consortium. Keywords: X-ray sorting, ore sorting, XRF analysis, XRT analysis

Jan 1, 2020

By M. Asghari, R. Amiri, A. Haratian, S. Haji

The aim of this investigation is the evaluation of optimising the Shahroud copper ore beneficiation plant near the Iranian city of Shahroud, by means of a sensor-based ore sorter applying X-ray transmission technology. Currently, this plant’s feed capacity of 52t/h produces 0.5t/h copper concentrate with a grade of 30% and copper recovery of 85% from a feed grade of 0.36%. By applying an X-ray transmission-based (XRT) sorter, it is possible to preconcentrate the feed and remove the gangue materials before entering the plant, enabling the production rate of concentrate to be increased. In this study, the obtained representative sample from the plant was preconcentrated in particle size of - 75+10mm by using the X-ray sorter, thus the concentrate with Cu grade of 0.85% was obtained. Therefore, by using of X-ray sorter the Cu grade of plant feed was increased to 0.48%. By increasing the feed grade from 0.36% to 0.48%, and considering a Cu recovery of 85%, the production rate will be increased from 0.48t/h to 0.61t/h. Therefore, the preconcentration by using the XRT sorter increases the production rate by 27%. Keywords: Optimisation, preconcentration, copper, X-ray, sensor-based ore sorting

Jan 1, 2020

By J. P. Garnier, T. Bhambhani, J. A. Garcia, N. Renaud

Most flotation plants use a static reagent scheme, i.e., a set combination of collectors, frothers, and modifiers. This scheme is usually developed and refined over time to deliver optimal (not necessarily the highest) performance when the major ore types are fed to the plant. However, when ore types or mineralogy coming to the plant change substantially (and this often happens as different areas of the pit(s) are mined and crushed at the same time), there are upsets in the process, typically leading to lower recoveries. Adapting to this variability is usually done only when performance drastically suffers, and the changes made may be too late and bring additional variability in performance. The premise for SmartFloat™ is that the reagent suite needs to be dynamic, adapting continuously to changes in the ore and operating conditions. Solvay has combined advanced analytics and data science techniques with its expertise in flotation reagent chemistry to systematically and automatically achieve the above, and in real time. Thus, SmartFloat™ is optimizing the reagent suite continuously, removing the additional variability created by belated human interactions resulting in a better and more stable process. In addition, this advanced approach allows for continuous improvement by identifying poor performing ore domains and improving the reagent suite using Solvay’s FM-100 approach to design appropriate solutions.

Jan 1, 2023

By A. S. Geldenhuys, L. S. Leal Filho, D. A. Deglon, T. C. Souza Pinto

The Brucutu iron ore mine (Minas Gerais, Brazil), is Vale`s largest iron producing operation achieving around 21 million tons by flotation of iron ore pellet feed per annum. The run of mine is mainly composed of hematite (70%) and quartz (30%). After preparation (comminution and sizing), the slurry is submitted to reverse cationic flotation of quartz under basic conditions (pH=10.5). Corn starch (500g/t) is used to depress Fe-bearing minerals and alkyl (C10) ether amine is the collector for quartz. The flotation circuit is arranged in a “coarse” section utilizing dated 28m3 square Wemco cells, and a “fine” section utilizing modern 160m3 tank cells. The “coarse” flotation circuit treats material from the deslime cyclone underflow while the “fine” circuit treats material from the deslime cyclone overflow and the pulp product from the “coarse” circuit scavenger 2 bank. Evaluation of process performance is of high importance as even small gains can lead to large improvements for this high throughput plant. Cell-by-cell samples of the froth products, selected feed and pulp-products were analyzed for flow-rate, overall chemical composition, and particle size distribution. Bank-by-bank samples of the feed, froth and pulp products were analyzed on an assay-by-size basis. In addition, the flotation cells were hydrodynamically characterized and gas dispersion parameters assessed. The detailed experimental program resulted in a thorough characterization of the process and enough information to produce a calibrated floatability component model. Longer mainline residence time results in significant Fe2O3 losses while yielding little benefit in terms of SiO2 grade. Scavenger 2 has twice the residence time of scavenger 1 while having to treat only 10% of the SiO2; resulting in high Fe2O3 recoveries to the froth and poor separation. In addition, it is shown that the Fe2O3 exhibits true flotation behavior resulting in increased Fe2O3 losses. The detailed data collection campaign coupled with in depth data analysis and modelling gives unprecedented information and highlights avenues for optimization that was previously unknown. Keywords: Froth Flotation, Process modelling, Process evaluation, Metallurgical survey

Jan 1, 2020

By H. Laitala, M. Lampi

Metso Outotec has developed a wide range of solvent-extraction technologies over decades and has introduced Metso Outotec VSF®X solvent-extraction plant. Standardized and modularized, Metso Outotec VSFX Plant provides a novel way to design, manufacture, transport, install, operate, and maintain solvent-extraction plants far better than in the past with highly sustainable and safe methods. For the customer, this means fast-track projects with savings in means of time, costs, quality, and operation. Sicomines and Metso Outotec have together implemented and commissioned a modern and efficient copper solvent-extraction plant. Plant commissioning and ramp up of the plant were fast and the plant is now operating efficiently. This paper presents Sicomines’ VSFX copper solvent-extraction project and gives a sight into operating figures for the plant.

Jan 1, 2023

By Y. Tanaka, H. Miki, Y. Aoki, H. Okamoto, G. P. W. Suyantar, T. Hirajima

Due to environmental limitations and the scarcity of freshwater, flotation using seawater or desalinated seawater as process water becomes more common for mining operations. On the other hand, seawater has been reported to affect the flotation behavior of sulfide minerals. Few reports are available on influence of pyrite depression, recycled seawater and lime consumption on flotation by using seawater. In this study, the flotation tests were performed using ore sample to investigate the effect of pH with seawater and process water used in plant on the flotation behavior in a laboratory-scale flotation cell and a pilot plant-scale. The results of laboratory scale flotation indicated that copper and molybdenum flotation kinetics decreased with increasing pH. Furthermore, the iron (mainly pyrite) recovery decreased with increasing pH. The pilot plant-scale flotation test showed that water with a higher concentration of magnesium and calcium (plant processes water) consumed a higher amount of lime. Because of low lime consumption and high copper and molybdenum recovery and grade, pH 8 is suitable compared with pH 8.5 for flotation. Keywords: seawater, process water, copper-molybdenum rougher flotation, pH, pilot test

Jan 1, 2020

By R. T. Rudd

DISCUSSION R. T. RUDD I have the following comments on Mr Bosman's paper. Before giving the company permission to discharge neutralized mine drainage containing 1800 mg/l of dissolved solids into a public stream, my Department had to consider the matter from both the legal and the practical viewpoint.

Jan 4, 1974

By A. Mainza, I. Govender, Elbasher M. E. Ahmed

A mechanistic description of axial segregation in rotating drum flows remains an open question. Consequently, optimal mixing of grinding balls and rocks for efficient breakage, maximum production of fines, and slurry transport is seldom achieved. Experimental and numerical studies of granular mixtures in rotating drums identify alternating axial bands that eventually coarsen in the long-term limit. Most models of axial segregation are limited to binary mixtures and cannot always predict the logarithmic coarsening effects observed experimentally. A key missing factor is a robust description of the axial free surface profile that is valid across a wide range of flow regimes. We present a practical model of the axial free surface profile by linking it to readily-derived geometric features of the cross-sectional S-shaped free surface profile. A parametric study shows good agreement with experimental measurements reported in the literature and heuristically valid trends.

May 1, 2021

By K. W. Falconer

The Witbank-Middelburg Branch of The South African Institute of Mining and Metallurgy celebrated 100 years of coal mining in the Witbank area with a function held at Douglas Colliery on the 5th December, 1989. Two hundred guests associated with the industry attended the occasion, at which Mr A.A. Sealey, Chairman of Rand Mines, Coal and Base Minerals Division, unveiled a plaque presented to the municipality.

Jan 1, 1990

By John Freer

As an innovation on the annual programme, the Excursions Sub-Committee organized a social get together of the Institute's Councillors and their families on Sunday, 27th February, 1983. Asian Mining - change of date The Second Asian Mining Conference, previously announced as being held in Manila, The Philippines, from 5th to 8th November, 1984, will now be held in Manila from 11th to 14th February, 1985.

Jan 1, 1983

By H. Ogasawara

Information on rock stress is important for safe mining in seismically active ground. On a major gold mine, a few tens of crews are continuously conducting geological drilling with small pneumatic machines. However, stress measurements are not often carried out in South African deep-level gold mines. One of the reasons is the drilling diameter that overcoring requires, which is much larger than the diameters used in regular geological drilling, e.g. Boart Longyear Metre Eater, which drills AQ or BQ holes. Larger diameter holes result in slower drilling advance, more load in transportation and handling at sites, and higher cost. In order to enable overcoring in BX size (60 mm diameter), we modified the compact conical-ended borehole overcoring (CCBO) technique that has been suggested by International Society for Rock Mechanics (ISRM) and was originally designed for NX drilling (76 mm diameter). With a single overcoring, the 3-D stress tensor can be determined. We tested this modified method at a depth of about 3 km at Moab Khotsong mine in South Africa. We worked with drilling crew who usually work at geological drilling with the Metre Eater. In January 2011, we tried using regular geological drilling tools (a sequence of a normal BX bit, reamer, and rod) without success. In August and September 2011, introducing stabilizers and thin BX bits, we succeeded. We could complete a cycle of procedures necessary for an overcoring, including shaping the borehole-end conically, glueing a 16-element strain cell, and overcoring, within 2.5 hours. Only 10 cm overcoring is needed, which increases the chance of successful overcoring in heavily fractured conditions. This modified method is suitable for up-dip holes to depths of 10-15 m from tunnels, and has the potential to be widely used at the initial stage of geological exploration drilling at many localities.

Jan 1, 2012

By K. H. Zhang, Y. P. Gao, J. Q. Zhao, Q. Li, J. C. Ma

Compared with sinusoidal oscillation, non-sinusoidal oscillation enhances the ability to control waveform and meets different oscillation requirements by adding an independent parameter, which is the key technology for high-efficiency continuous casting. A new waveform of mould non-sinusoidal oscillation is proposed in this paper, that is, a velocity waveform that is composed only of straight lines and parabolas, which not only has good dynamic characteristics, but also further enhances the feature of non-sinusoidal oscillation. Compared with sinusoidal oscillation, the negative strip time is reduced by 15.9%, the maximum negative strip velocity difference is increased by 38.3%, and the maximum positive strip velocity difference is decreased by 27.8%. The formulas of oscillation process parameters can be clearly deduced, and the isoplethic curves of oscillation process parameters when multi-parameter simultaneously changes are drawn. The negative strip time decreases as the modification ratio, frequency, and casting speed increase, but increases as stroke increases. In order to maintain the stability of negative strip time, an oscillation synchronous control model for optimising oscillation basic parameters was developed. Through practical application, the mean oscillation mark depths decreased by 10.1 μm and the flux consumption is increased from 0.37 kg/t to 0.45 kg/t in the non-sinusoidal oscillation model, which meets the requirements of normal production.

Oct 24, 2025