Search Documents

By Verne E. Hooker

This Bureau of Mines report summarizes the results of modifications in the borehole deformation gage design and subsequent changes in the overcoring techniques. Modifications in the borehole deformation gage have greatly improved the creep characteristics and enhanced the versatility of the gage. In situ field tests in competent rock near St. Cloud, Minn., provided sufficient data to compare the reliability between gages and new techniques in obtaining good engineering estimates of stresses. Near-surface horizontal stresses at the test sites are compressive and biaxial in nature.

Jan 1, 1974

By S. P. Kinney, P. H. Royster, T. L. Joseph

"The study described in this paper, on the reactions in an iron blast furnace, is part of the investigation being conducted by the Bureau of Mines on combustion of coke and the reduction of iron oxides in the blast furnace. Previous study of the combustion zone of the iron blast furnace, by means of a series of as samples taken through the tuyeres across the hearths of 13 blast furnaces, showed that the combustion of the coke in the blast-furnace hearth is complete at a distance of 32 to 40 inches from the nose of the tuyere, measured horizontally toward the center of the furnace. The results of this previous work are sum¬marized in the curves shown in figure 1, where it will be noted that practically all of the oxygen disappears at a distance of approximately 30 inches from the nose of the tuyere.In order to determine the height at which oxygen is found in a vertical direction above the tuyeres - it had been suggested that the combustion zone turned upward near the tuyere and to obtain comparisons with the samples taken at the Bureau of Mines experimental6 (5-ton) blast-furnace at Minneapolis, the Bureau extended the gas sampling on a commercial furnace to a number of planes between the tuyere level and the stock line. The sampling was conducted on a 300-ton furnace, making foundry iron, operated by the Central Iron and Coal Co., at Holt, Ala. The furnace was smelting Southern red and brown ores and nodules from pyrite sinter. Figure 3 is a vertical section of the furnace showing the six planes sampled."

Apr 1, 1926

By J. F. Barkley

Smoke abatement is a subject of which fuel technology, although absolutely essential, is only a part. Its successful accomplishment starts and ends with human factors that must be given thorough consideration; between this "start" and "end" fuel technology is applied. Smoke abatement usually starts from the desire of some person or persons to be free from uncleanness caused by the stack of someone else and ends with the sincere desire of the operator of the fuel-burning equipment to maintain a clear stack. Although "smoke abatement been discussed for many years, it is only recently that the public has been mindful of such expressions as "air pollution" and "air hygiene." The subject has duel in common with that of supplying pure water but is more complicated. The public desires pure water, expects pure water, is willing to pay for pure water, and expects to continue to pay for it indefinitely; it is a development of civilization. It is doubtless correct to say, however, that people in general do not et realize the detriment of air pollution to their well-being or give the question enough serious consideration. This is illustrated by the fact that in city smoke abatement it is the mass of small householders that sins the most and is the hardest to handle. It is rather difficult to assemble a group of people in a room without the air becoming contaminated with smoke. Smoke abatement will lag with the lack of desire for pure air - probably the biggest human factor involved in its accomplishment.

Jan 1, 1939

By Mark I. Copeland

A study was conducted to determine if commonly used alloying additions or coating materials can prevent the formation of a liquid-copper phase during the reheating of copper-containing steels. If so, the tendency of such steels to surface-crack during hot-working might be eliminated. Steel specimens were scaled by heating them either isothermally or in a programed manner that simulated industrial furnace practice. Metallographic examination of the heated specimens showed that molten fayalite (Fe2Si04) completely prevented the formation of liquid copper at the surface. Fayalite, which melts at 2,200° F (1,205° C), was formed by internal oxidation of the silicon contained in the steel. By forming complex molten oxides, coatings of borax glass were also effective in preventing the occurrence of liquid copper at the steel surface.

Jan 1, 1972

By Will B. Jamison

An ignition detection and suppression system was developed under the scope of this contract. The objective of this machine mounted system was to detect flames caused by frictional sparking from the cutting bits of a continuous mining machine and to suppress it with sufficient speed to prevent the development of an explosion, and to keep the flame from harming the machine operator.

Jan 1, 1976

The contract objective was to evaluate sources of airborne quartz and research control methods that would assist underground mine operators in complying with respirable dust standards which have been reduced because of quartz in the dust exceeding five percent. The work involved: Phase I -evaluate sources of quartz dust at the roof bolter work location; Phase II -evaluate the relationship between the quartz content of the coal and adjoining rock strata and quartz exposure at the roof bolter and continuous miner locations Phase III -conduct laboratory tests to determine performance parameters for roof bolter dust collector systems. The underground surveys for Phases I and II determined: (1) the continuous miner typically is the greatest source of quartz exposure for the miner and roof bolter operators when single-split ventilation is utilized, (2) a statistically significant relationship be­tween quartz content in face material and operator exposure was not determined and data suggested mining equipment and procedures may be more critical. The Phase III lab tests indicated the use of dust hog-type bits, filter cartridges, maximized collector airflow, and reduced bit rpm should be utilized to minimize dust liberation at the roof bolter.

Jan 1, 1985

By F. J. Perzak

The Bureau of Mines conducted a study to develop a standard fire test for 5-gal containers used for storing combustible fluids in underground coal mines. A standard test method was developed which evaluates the performance of the container in a 4-min tray fire. Bureau investigators used the standard test method to evaluate several types of closed 5-gal plastic and metal cans in outdoor tests. Each can tested contained 1 gal of nonfire-resistant (NFR) hydraulic oil. A container failed the test if it lost its contents in any of seven trials. Contents spilled either as a result of thermal rupture or melting. Fewer than 10 pct of the metal containers failed this criterion, but all the plastic containers failed. The metal container failures were usual-ly due to tipping over during pressure relief, which spilled the NFR oil. Replacing the NFR oil in the container with kerosene resulted in failure of more than 30 pct of the metal containers. The standard tests and preliminary tests showed that plastic containers are not equivalent to metal containers in their ability to contain combustibles such as lubricants and greases in a fire. For solvents and lubricants more volatile than NFR hydraulic oil, approved metal safety containers are recommended.

Jan 1, 1985

By Jon K. Ahlness

The Bureau of Mines investigated technologies for testing the integrity of in situ leach mining wells, as required by environmental regulations. To test for leaks, inflatable packers were used to seal the well casing. Laboratory testing determined that the packers could contain a casing pressure up to 50 to 60 psi (345 to 414 kPa) less than the packer inflation pressure. Single-and double-packer configurations were successfully field-tested in 32 wells ranging from 500 to 530 ft (153 to 162 m) in depth. A rigid pipeline and a hoist truck were used to run the packers in and out of the wells for the double-packer tests, which averaged 2-1/4 h each. In an effort to decrease the time of the rigid-pipe double-packer test. a self-contained trailer-mounted test system was designed and built. It utilizes a winch and steel cable to run the packers in and out of the well and high-pressure nylon tubing for packer inflation. This system was successfully field-tested in eight wells averaging 650 ft (198 m) in depth and resulted in a time savings of 13 pct and an operator-hour reduction of 42 pct.

Jan 1, 1985

By D. B. Taliaferro, Thomas Jennings, C. M. Keithly

"INTRODUCTION This report describes the methods of development and operation and gives the results of controlled water injection into oil sands in Illinois. It is the third of a group relating to water-flooding operations in various States; previous reports have covered projects in Oklahome 5/ and Kansas.6/ Systmatic water flooding has been in progress, in these States, for more 10 years. In Illinois the Tide Water Associated Oil Co. has been injesting water into one or two wells on each of five leases in the Robinson Acknowledgments This study was made under the general supervision of R. A. Cattell, chief engineer, and H. C. Fowler, assistant chief engineer, Petroleum and Natural Gas Division, Bureau of Mines, Washington, D. C., and N. A. C. Smith, supervising engineer, Petroleum Experiment Station, Bureau of Mines, Bartlesville, Okla., and under the direct supervision of Ludwig Schmidt, senior petroleum engineer, Bureau of Mines, Bartlesville, Okla.The cooperation of the operators who are conducting water-flooding projects and who have made this report possible by furnishing data on their operations is gratefully acknowledged. The writers are grateful also to the following members of the Bureau of Mines for assistance in preparation and criticism of the manuscript: C. J. Wilhelm, Franklin, Pa.; and Gustav Wade, R. E. Heithecker, and Peter Grandone, Bartlesville, Okla. The illustrations were prepared by Helen Cramer, Petroleum Experiment Station, Bureau of Mines, Bartlesville, Okla."

Aug 1, 1944

By Andrew K. C. Wong

Hydraulic transport has been considered as one of the most economical methods in transferring granular materials over relatively long distances. In the natural world, it is used to transport basic material required for the support of life; in industry, it is a method widely adopted for handling materials. But the phenomena of hydraulic transport has not yet been thoroughly understood. As most of them are conditioned by a number of hydraulic and mechanical parameters, of which the basic relationships are not fully known, the traditional approach in relating these parameters to the energy requirement is purely empirical in nature. Empirical formulas, such as that proposed by Durand, (1) only give satisfactory results over a selected range of (particle size)/(pipe diameter) ratios and slurry concentration. When the case is more complicated or when new situations arise, the empirical formulas fail to give good predictory results. In fact, most of these formulas are based upon dimensional analysis, where the underlying physical interaction is not explicitly considered. Apart from the loosely related, non-dimensional groups incorporated in the formulas, there is practically no analytical means for modifying the formula so as to enable it to cope with more complex real physical situations. Although it seems quite remote that a complete rigorous solution to this highly complex problem could be generated in the near future, it is generally recognized (2, 3) that research in this area should be directed to more comprehensive studies of the obscure phenomena. In fact, there are a good number of very basic problems such as the effects of gradation and concentration of particles upon

Jan 1, 1972

By D. D. Bush

Based on the results of this study, the underhand cut and fill stoping method, with mass destressing, is an effective method for controlling rock bursts and falls of ground for deep mining in the Coeur d'Alene Mining District. The procedure can be utilized to pull highly stressed pillars by converting from conventional overhand stoping methods or used as a primary recovery system. During the demonstration, only one minor rock burst occurred, with no injuries. The system facilitates accurate placement of vertical boreholes for effective mass destressing. Each mining cut is filled with cemented sandfill overlying a timbered mat that forms the back for the succeeding cut. For this demonstration, a cemented fill was mixed on the surface and piped to the stone. Costs for pillar recovery by this method are comparable and are considered cost effective over conventionally timbered overhand mining as a pillar recovery method.

Jan 1, 1982

By Diane M. Doyle-Coombs

In late July 1985, air samples from a sealed portion of the Quinland coal mine in West Virginia showed the presence of carbon monoxide (CO). Mine Safety and Health Administration (MSHA) personnel concluded that a fire was burning behind the seals. Since an imminent danger existed, the mine operator was given a closure order. The gases behind the seals were monitored and almost 2 million ff of carbon dioxide (C02) gas was pumped into the sealed area to stabilize the environment. Sixteen days after the closure order was issued, MSHA allowed the mine to return to production. Approximately 1 yr later, mine management submitted a seal breaching request to MSHA in order to drive a set of entries to further develop the mine. The Bureau of Mines established a sampling strategy and monitored gases from behind the sealed area during the breaching operation until the atmosphere was safe. This report is an account of the seal breaching conducted by the mine, MSHA, and the Bureau. The logistics of this event, the sampling strategy, and the equations applied could be used by the mining industry in future breachings or mine recovery operations. Time to reenter the area was calculated by using the methane (CH4) concentrations sampled at the discharge of the seals. Tracer gas was used to verify the ventilation flows through the area.

Jan 1, 1988

By Kevin Connor

There was little change during 1988 in the production of minerals in Burundi. The Government of Burundi, which banned all commercial mining operations in the country in 1979, lifted the ban on mining of alluvial gold deposits and started a program of small-scale artisan gold mining in October. Along with the legal mining of gold, licensed gold trading counters were established. Other mineral commodities produced were kaolin clay, lime, and peat. In compliance with the Government ban, the only mineral wealth exploited for commercial sale and export was alluvial gold. Through financial assistance from the International Bank for Reconstruction and Development (World Bank) and the United Nations Development Program (UNDP), a study to inventory the country's mineral resources continued throughout the year. As part of this study, during the year, a West German company undertook a drilling program to further outline the nickel reserves of the Musongati area in central Burundi. Results of the work as of yearend were disappointing, with only 12 million tons of ore identified with better than 2% nickel content proven. Investigations also continued during the year regarding the centrally located deposits of vanadium-bearing titaniferous magnetite. A Norwegian company contracted to prepare a prefeasibility study for developing the deposit. The British Sulphur Corp. Ltd. was nearing completion of its $1.2 million2 study of the phosphatic limestone deposit at Matongo-Bandaga at yearend. Ore reserves of about 17 million tons grading 11% phosphorus pentoxide (P2O3) had been identified. The phosphate zone overlies a carbonatite rock, which could provide the basis for a cement industry. Additional drilling was planned for 1984. Exploration for gold was underway in 19S3 in northern Burundi through UNDP funding. Several primary deposits of shallow semimassive sulfides with gold values ranging from traces to 11 grams per ton had been discovered. With assistance from the Federal Republic of Germany, bastnasite reserves of 5,400 tons, with associated high europium oxide and cerium content, were verified, and the prospects for finding

Jan 1, 1985

By Robert P. Bruno

This report covers the study of the feasibility of using a hand-held infrared viewer as a methane indicator to observe methane gas at the face of an underground coal mine. The objective of this program was the development of a hand-held device to remotely detect the presence of concentrations of methane gas in underground coal mines. Convenient "mapping" of methane from a remote location would allow rapid and safe corrective procedures for working personnel. Modified commercially available equipment was evaluated both in the laboratory and in a working mine. Although readings were obtained and the general principle of operation demonstrated, the power levels necessary, and protective enclosures required, would raise the weight of the instrument beyond practical limits of portability. Based on currently available technology, it is the conclusion of the investigations that a practical, portable, hand-held visual methane indicator is beyond the state-of-the-art. The recommendation was, therefore, made that work be suspended, and the results and data compiled and presented in a final program report.

Jan 1, 1979

By F. A. Rutledge

The Batesville district in north central Arkansas is one of the important sources of manganese ore and ferruginous manganese ore in the United States, with a history of production dating back to 1849. From studies by the Federal Geological Survey, it was recognized that the district probably still contains substantial reserves of low-grade ore. It was natural, therefore, that the deposits in this area should be among the first investigated by the Bureau of Mines under the Strategic Materials Act of June 1939, by which the Bureau was authorized to explore domestic deposits of strategic minerals, at that time designated as those of antimony, chromium, manganese, mercury, nickel, tin, and tungsten. The field work of the Bureau of Mines in the Batesville district was done in two distinct phases. Under project 308, active from August 1940 to June 1941, carbonate-oxide ores were investigated at five separate areas in which 100 trenches, test pits, shafts, and edits aggregating 4,364 linear feet were excavated and 839 samples were taken and assayed. Under project 323, in progress from February 1941 to January 1942, wad deposits were explored at 10 separate areas by 408 prospect shafts, churn-drill holes, and bucket-drill holes aggregating 23,680 linear feet from which 285 samples were taken and assayed. Processes for beneficiating the wad ores were investigated at ore-testing laboratories of the Bureau of Mines.

Jan 1, 1952

By H. P. Rue

The Bureau of Mines has recently collected two samples of crude oil from wells in the Greasewood Flat area of northeastern Colorado. Sample 31310 was taken from the Continental Oil Co.'s well Briggs No. 1 which care in or September 27, 1931, with a maximum production of 940 barrels per day. Sample 31311 was taken from tie Reiter-Foster Oil Co. Is well Ida Johnson No. 1 which came in on August 24, 1931 with a maximum production of approximately 1000 barrels per day.

Jan 1, 1932

By Edward L. Tullis

Numerous widely distributed pegmatites of the southern Black Hills of South Dakota contain small amounts of beryl, and two minor deposits are known in the northern Black Hills. Few mines have produced more than 50 tons, and the current, rate of production for the area is about 100 tons annually. Total production, since the first records, is 2,358 tons. Most of the deposits contain less than 1 percent beryl, although the beryl zones in several deposits contain 2 percent beryl or more. Estimated reserves of beryl total 11,824 tons, and an additional 234 tons has been measured; there are other unestimated reserves. The pegmatites are in a belt about the margin of the Harney Peak batholith in the southern Black Hills, although they fail into three districts. The most important, from the point of view of production and reserves, is the Keystone district. Many deposits also are found in the vicinity of Custer and Pringle. Small amounts of beryl occur in the dikes near Hill City. A little beryl has been produced from the Tinton district in the northern Black Hills, and an undeveloped dike has been discovered on Whitewood Peak near Deadwood. The beryl-bearing pegmatites are principally coarse-grained intergrowths or massive segregations of feldspar, quartz, and mica. Some of them contain notable amounts of lithium minerals, as well as some tantalite, columbite, and cassiterite.

Jan 1, 1952

By C. H. Manney

This report deals with the feasibility of the use of vocoders as an integral part of a mine electromagnetic voice communication system. Limitations imposed by the nature of the transmission path, background noise and equipment are examined. Some properties of vocoders and apparent advantages of the use of vocoders in a mine communication are discussed. The conclusion is reached that the man-made noise level will ultimately determine the workability of such a system.

Jan 1, 1972

By F. J. Perzak

The Bureau of Mines conducted a flammability study of plastic ventilation ducts. Six rigid 16-in-diam fiberglass-reinforced plastic ducts from five manufacturers were examined using laboratory-scale, large-scale, and full-scale fire tests. The laboratory-scale tests included the American Society for Testing and Materials E162 radiant panel test, the E2863 oxygen index test, and the standardized small-scale flammability test (S3FT) developed by the Mine Safety and Health Administration (MSHA), U.S. Department of Labor, and replicated by the Bureau of Mines. Ten-foot lengths of the same ducts were also subjected to a large-scale vertical fire test, and 20-to 30-ft lengths were tested in a full-scale in-mine fire test at the Bureau's Lake Lynn Laboratory mine. The data from the laboratory-scale radiant panel test and oxygen index test indicated that the ducts were fire-resistant, However, five of the six ducts failed the S3FT and vertical fire tests, and four of the ducts failed the full-scale in-mine tests with flame propagation rates that ranged from 3 to 10 ft/min. The results indicate the need for improved fire-resistant plastic ducts. The good agreement between the S3FT re-sults and the vertical and full-scale tests show that the S3FT provides a good indication of the flammability of fiberglass-reinforced plastic ducting under realistic fire conditions.

Jan 1, 1987

By Jeffrey P. Schubert

The study site in northeastern Illinois underwent surface mining for coal in 1943 and was reclaimed by the state of Illinois in 1972-1973. Additional soil amendments and seed were applied to the spoil surface in 1975-1980. Previous studies in 1975-1978 had shown that the surface spoil materials and five final-cut lakes at the site were quite acidic and the lakes contained high concentrations of sulfate and dissolved metals. Surface runoff water from monitoring plots in 1976 were only moderately acidic and the mean concentrations of most dissolved metals and sulfate in the runoff waters were less than 25% of the concentrations found in Lake B. By 1980, vegetation had become well established over most of the mined area. However, the five final-cut lakes (Lakes A-E) remained acidic. The purpose of the study reported here was to determine the physical and geochemical subsurface conditions of the spoil materials, the hydrologic flow system within the spoils, and the magnitude of acidic spoil leachate migration into the lakes and into the wetland prairie north of the mine site. Lakes A, B, C, and E were still very acidic in 1980-1981 (pH range: 2.9-3.4; aridity range: 110-860 mg/L as CaCO3). Lake B had the worst water quality, with mean concentrations of dissolved aluminum, iron, manganese, and sulfate of 75, 25, 37, and 3340 mg/L, respectively. Shallow groundwaters in spoil materials around Lake B had a lower pH and about two to four times greater concentrations of aridity, aluminum, manganese, zinc, and other metals and nearly 20 times greater dissolved iron than the water in Lake B. The shallow groundwaters in undisturbed soils and bedrock 10-30 m north of the mine site spoils generally were alkaline, but did contain occasional moderately high sulfate and metal concentrations. Pumping tests and recovery tests conducted in piezometers showed hydraulic conductivities of spoil materials ranging from less than 10- to 10-5 m/s; hydraulic conductivities of natural soils and bedrock were measured between 10-10 to 10-7 m/s. Water levels in spoil materials increased rapidly in response to rainstorm events and the recession curves were relatively quick to decline, lasting only two or three days. Quick infiltration of rainfall into the spoil surface and percolation down to the water table caused a rise in groundwater levels and movement of spoil groundwater into the lakes. This groundwater component in the lake water budgets could account for most of the water quality problems occurring in the acid lakes.

Jan 1, 1984