Search Documents

By L. Russell Payne

The use of shock tube in the blasting industry is relatively well characterized and understood within the realms to which it is used. Non-conventional uses of shock tube within the EOD and the Aerospace Industry however has not been as widely researched and published. Characteristics of shock tube such as its reliability, simplicity and its non-electric nature make it ideal for functioning or driving mechanical mechanisms, detonators, and timing devices. Outlined in the text are the performance characteristics of shock tube in an array of atmospheric environments including pressures ranging from ambient to 100,000 ft equivalent atmosphere. In addition the useful exit work energy or impulse of the shock tube for driving these various EOD and Aerospace mechanisms is published as a function of tube lengths and atmospheric pressures. Of particular interest to these devices is the required length of shock tube needed to produce the steady state detonation energies and the accompanying properties of the shock tube at these lengths. Various sources publish an arbitrary run distance for steady state detonation and output some where between 20 cm and 1.0 meter. Statistical and experimental evidence with in the text show these numbers to be low and provides an updated reference for shock tubes usage in nonconventional situations.

Jan 1, 2008

By Richard J. Mainiero, Marcia L. Harris, James H. Rowland

In the past several years, there have been a number of blasting-related carbon monoxide migration incidents. In each case, there have been some common factors that appear to be related to carbon monoxide migration. Geology, heavy confinement of the blast, close proximity to the affected structure, and open pathways into the affected structure are just a few. Prince William County, VA is an area undergoing a boom in suburban development. In the year 2001, more than 4,050 new homes were constructed within the county.1 In the new housing development located in Bristow, VA, trench blasting was utilized to excavate proposed sewage and utility lines. On November 8, 2002, a trench blast was conducted for the installation of utility lines. Later that evening a carbon monoxide detector alarmed in a nearby house. The gas company and fire department sampled for carbon monoxide and measured 100 ppm and more than 200 ppm on the first floor and in the basement respectively. Subsequent efforts to prevent migration of CO into the nearby homes met with mixed results. The only reliable technique for protecting neighbors from CO appears to be the placement of CO monitors in the homes. The events are presented and discussed.

Jan 1, 2004

By Chris Searing

An underground room-and-pillar limestone mine in Western Missouri acquired a new primary crusher, physically larger in every dimension than the unit it replaced. Due to the space constraints within the mine, resetting the truck dump and feeder to account for the larger crusher was unfeasible. Mine management determined the most practical solution was to increase the available area for the new crusher via blasting. Fitting the new crusher into the existing area required the removal of 6 feet (1.83m) of limestone from the original floor grade. Blast parameters had to be designed to effectively break this shallow depth of rock while controlling movement to avoid contacting the mine back 23 feet (7.01m) overhead, an apron feeder 13 feet (3.96m) above the southern extent of the area, and the original crusher which was still in place 15 feet (4.57m) from the first pattern. Additionally, work needed to be completed within an aggressive schedule set forth by the mine, allowing little room for delay or error. This paper will examine the efforts taken to safely and effectively blast the rock while protecting nearby equipment and integrity of the mine back. Subjects covered will include blast design, adjustments made to account for drilling and equipment-related constraints, and how seemingly small changes in load parameters can significantly impact performance with small-diameter blast design.

Feb 6, 2023

By Zhiwei Jiao, Ziqing Guo, Mushen Wang, Yueda Fang, Qiuming Tang

In order to achieve anti-terrorism, production safety, better explosive performance, lower cost, and environment protection, we developed HMS (emulsification in borehole).Long-process PM (plant-mixed) and SM (site-mixed) emulsion trucks are reviewed and compared to a new type of short-process HM (hole-mixed) truck for onsite emulsion manufacturing. The short-process HM truck has demonstrated many advantages over its PM and SM counterparts in areas such as process safety and security, energy efficiency and environmental impacts: 1) No emulsion matrix is manufactured in the plant, transported on public roads, or even present on the surfaces of blasting job sites. Such characteristics are certainly beneficial in eliminating risks of the product being diverted and used by unlawful players; 2) This short-process involves "micro-fluid control to form super oil phase-rich" in tubular emulsification process, making it intrinsically safe; 3) There is basically no residual matrix left in the truck or on the job site to clean up, which greatly reduces environmental impact of the process; 4) Comparing with typical PM and SM trucks, the HM truck has eliminated the needs of many power equipment and critical pump pressure for turbulent flow forming a static emulsification with super oil phase -rich is only 0.2Mpa. These is therefore quite energy efficient.

Feb 1, 2020

By D. Goodings, W. L. Fourney, Bonenberger, R., Uli Leiste

The problem of the maximum depth at which a mine buried in the surf zone or beach zone is a threat to landing vehicles is being studied by Naval Surface Warfare Center (NSWC), Indian Head Division, Naval Research Laboratory (NRL), and The University of Maryland Dynamic Effects Laboratory. The problem was divided into two parts: The first part involves determining how deep a pressure plate mine can be and still detect a vehicle passing over it. This requires determining the distribution of stress within dry and saturated sand when a vehicle passes over a buried mine. The results obtained from that study are presented in a related paper (1). This paper will cover the second part, which entails determining the impulse delivered to the vehicle. This is equivalent to determining the impulse delivered to a plate suspended above the detonating explosive charge and includes an investigation of the distribution of the impulse over the plate. The purpose of the research is to develop a scaling law and/or computational capability which will permit predicting impulse to be expected in the field from tests conducted in the lab. The computational effort is aimed at the development of and confidence in computer codes that can be used to predict stresses and strains in plates due to the detonation of buried mines.

Jan 1, 2004

By A K. Raina, P B. Chourdhury

Flyrock is the unwanted throw of rock fragments to excessive distances in opencast blasting. The incidence is relative in nature incorporating the distance of objects of concern like structures within and outside the mine, equipment within the mine & near the blast and persons within and off the mine. Several attempts to predict and defi ne fl yrock made worldwide could not address the problem since the phenomenon is not a regular feature in blasting. This probabilistic nature of fl yrock allows for risk calculation. CIMFR, India developed a Factor of Safety based risk criterion (10, 14) for evaluation of throw/ fl yrock in opencast mines that incorporates all the above in terms of distance and allowable limit of throw – which in turn determines the risk. The criterion provides the blaster a tool for mathematical evaluation of fl yrock risk in terms of a Factor of Safety and threat ratio (defi ned for the 1st time), thereby enhancing confidence when blasting. The method is easy to use and has been applied to several mines in India and the results are signifi cant. This paper details the evolution of the concept and its application in three limestone mines of India and the results obtained. The application of the method for defi ning a fl exible danger zone is also discussed.

Jan 1, 2008

By Unknown

[Executive Director’s note: According to 17th edition of the ISEE Blasters Handbook in its section on trench blasting, “...consideration must be given to the proper venting of gases generated from the blasting. Should those gases spread laterally rather than vent directly to the surface, the gases may travel underground and finally vent well outside of the planned area. Such events may be caused by the strata, soil conditions or root systems, or existing and/or abandoned utilities or other man-made structures. In the worst situation, gases resulting from the detonation such as CO2, CO, and/or NOx may travel through the strata and find their way into basements of nearby homes or businesses. The IME has recommendations on how to minimize this potential problem. Some of the points include removing the overburden and digging the rock immediately after the shot, and drilling vent holes periodically between the ditch and adjacent homes.” The Board of Directors of the International Society of Explosives Engineers has expressed its concern that blasters be made aware of the issue of migration of carbon monoxide resulting from blasting operations. What follows are excerpts from “Carbon Monoxide - The Silent Hazard”, an article that was recently included in the Safety Update, Vol. 20, No. 1, 2001, published by Nobel Insurance Services.]

Jan 1, 2002

By J. Sigler

A series of small scale tests have been performed to establish the effect of powder factor and initiation timing on the grindability of rocks. The blasts were performed in high quality granite blocks, which were cut from stone prepared by dimensional stone quarry operations. Three different types of granite were tested. The charge configurations included detonating cord placed in five holes with water as a coupling medium or concentrated charges of equal mass, placed in the same number of holes, fully stemmed or air decked. The powder factor was varied from 0.4 to 1.2 kg/m3. Typically all charges were detonated simultaneously; however, in some experiments, detonation waves collided in the middle of each borehole and in others a small delay was used between charges. All fragments were collected and screened, and drop weight impact tests were performed on selected size fractions, using different impact energy, to calculate the resistance of the rock to impact breakage. The work index of some of the blasted samples was measured using a standard Bond mill arrangement. The experiments generally showed increased softening of the rock with powder factor, which appeared to be the dominant factor. Charge configuration as well as in-hole collisions of detonation waves affected the initial fragmentation but had little effect on the impact breakage of the samples.

Jan 1, 2008

By P. R. Mohanty, Kaushik Dey

Blast-induced tunnel overbreak prediction in the past has been based on peak particle velocity measured far from the blast site with necessary extrapolation. This has often resulted in suggesting higher damage threshold levels of Acceleration/PPV for overbreak prediction (Bogdanhoff, 1995, Holmberg and Persson, 1997, Murthy and Dey, 2002). These, site-specific far-field blast vibration studies, have also revealed that predicted PPV levels for overbreak could lie in the range of 700-5000 mm/s, an extremely wide range to generalize. Experimental blasts were conducted, in an underground metal mine located in eastern India, with an objective to study the level of acceleration /peak particle velocity generated in tunnel blasting. Accelerometers and tri-axial geophones with measuring ranges upto 500 g, 254 mm/s respectively, were mounted on the tunnel floor close to the blast face, with sensor distances varying from 15.25m to 36.10m. Due to straight faces the measuring distance could not be reduced further anticipating, in particular, cable damage. The equipment used was of M/s Instantel Inc., Canada. The blast pattern used was burn cut with large dia relief holes providing the required free face. The blast hole depth was 1.8m. Tunnel overbreak was measured using a telescopic offset rod fabricated at Indian School of Mines, Dhanbad, India.

Jan 1, 2004

By Christian Dye

"The following paper focuses on the developing relationship between the members of theInternational Society of Explosive Engineers (ISEE), and the mining students from the BritishColumbia Institute of Technology (BCIT). During the past two years mining students and theISEE members have worked closely in developing a student chapter within the society and onFebruary 1st 2015, the first Canadian Student Chapter was recognized at the annual generalmeeting in New Orleans. This paper discusses the benefits that both the industry and studentsgain with a strong relationship. The mining students recognize the importance for filling the rolesof retiring members of the society and industry. Prior to 2015 the school had only offered a twoyear diploma program in mining and mineral exploration methods. That included a brief sectionin the use of explosives in the mining industry. In September of 2015 students were recruited forthe first ever Bachelors in Mining and Mineral Resource Engineering program. This engineeringdegree includes a full four month course in advanced blasting and rock fragmentation. Studentssuccessfully completing the diploma program will have an entry level of technical understandingin how blasting is conducted. The students successfully completing the bachelor degree will havean in depth technical understanding of explosives and rock fragmentation. Having this uniqueand dynamic multi-level program provides the explosives industry with a pool of talent that canbe used to fill positions with graduates for all levels of the blasting industry."

Jan 1, 2016

By Gour Sen, Peter Bellairs

Blasting conducted in rock temperatures greater than or equal to 55°C (13 1 “F) and / or in rock containing sulphide minerals and their oxidation products can result in unplanned detonations. Blasting practices involving the identification of the affected areas together with the use of speciality explosive products and rigorous attention to quality control are required to safely blast in these types of environments. Sulphide dust explosions occur in some underground mines where the primary blast results in a secondary explosion of the sulphide rock dust which propagates some distance from the primary blast area. This phenomena results in considerable damage and the generation of significant volumes of toxic gasses delaying re-entry to the affected area of the mine thereby increasing both costs and safety concerns. The exothermic reaction between ammonium nitrate based explosives and rock types containing partially oxidised sulphides have resulted in numerous high risk blasting incidents. These reactions can occur at ambient temperatures and often result in premature detonations / deflagrations causing a great deal of consternation at the affected minesite resulting in lost production and considerable expenditure to solve the problem. Rock masses at elevated temperatures can also result in unplanned detonations unless appropriate precautions are taken. This paper discusses each of these hazards, cites some case studies and details appropriate generic safe and efficient blasting techniques for each of the above applications using appropriately formulated explosive products.

Jan 1, 2000

By Sehoon Lee, Duhwoe Jung, Eunsu Cha, Kyeonghwan Jeong

This case study presents the effectiveness of underground rock blasting to facilitate the trench cut in the hard rock layer using a conventional trench cutter for the construction of a diaphragm wall. Rock blastings are pre-performed up to the scheduled depth and then the fragmented rocks can be easily cut using a conventional trench cutter. Two trial underground rock blastings have been performed and the effectiveness of pre-blasting is presented in terms of a cutting rate, a loss of cutter heads and an amount of overbreak. Based on the results obtained from the trial underground rock blastings, the following conclusions can be appropriate: 1) A pre-blasting of hard rock layer located in depth can help to overcome the limitation of the trench cut using a conventional trench cutter. If the hard rock layer is fragmented after blasting, the fragmented rocks can be easily cut using a conventional trench cutter, 2) The speed of cutting works was accelerated and the loss of cutter heads was significantly reduced in the sections where the blastings were applied prior to cutting. 3) The amount of overbreak, expressed in terms of the amount of poured concrete, can be reduced to some extent. However, the location of blast holes in the trench can also contribute to the amount of overbreak. The closer the location of blast holes to the edge of the trench, the more extensive fractured and cracked zone can be formed on the face of the trench. This can increase the amount of overbreak if the trench is left empty for a while.

Jan 1, 2000

By Thomas A. Gelormino, Ulrich La Fosse

"Deep blasting was used to densify foundation soils for a large manufacturing facility inChicopee,Massachusetts. A 360,000 square foot building, whose construction began inthe summer of 1990, is founded on alluvial deposits up to 90 feet in depth. These deposits are comprised of saturated very loose to loose fine to medium grained sands with traces of silt and gravel. During the building foundation design it was found that to withstand earthquake forces without soil liquefaction, it would be necessary to improve portions of the alluvial deposits by densification. The zone in need of densification extended from approximate depths of 20 to 50 feet. Several conventional densification methods, including vibrocompaction and deep dynamic compaction, were evaluated along with deep blasting. Detonation of 1-3/4 inch diameter charges of 65 percent gelatin dynamite (Atlas Power Primer) installed inside 2-inch diameter PVC casings to a depth of up to 40 feet, was used to achieve the desired densification. This method was selected over others due to its lower cost and decreased construction time. Although used in New England once in1940 for a dam and once in 1960 for a transmission line tower to improve foundation soils, there is no precedent found in the literature for densification by blasting to improve liquefiable soils below a proposed building. Details of a test program and the production blasting, including vibration data are presented. Pre-and post-blasting data conclusely shows an increase in the density of the sand deposit after blasting."

Jan 1, 1991

By Lewis L. Oriard

Ground vibrations associated with blasting are generally in a higher frequency range and of shorter duration than those generated by earthquakes, and the intensity scales for earthquakes cannot be applied directly to blasting vibrations without modification. Further, the profession does not need an intensity scale merely to estimate vibration intensity. If the blasting in question was not monitored instrumentally, it is a simple matter to estimate the range of intensities based on published prediction formulae or data from various sources such as Oriard (1), Nicholls et al (2), Hendron and Oriard (3), Siskind et al (4), and others. However, the profession has a serious need, for purposes of evaluating damage claims, to understand the relationships between vibration intensities and the levels of observed effects. The criteria for threshold damage do not apply to typical cases which usually involve structural damage. If the damage in question would have required ground vibration with a particle velocity of, say, 20-120 ips, damage is not verified by showing that the vibration merely approached a suggested limit to avoid threshold damage. That is not the question. This paper provides some guidelines for comparing severity of damage to intensity of vibration which would be required to cause such damage, much as is done when determining earthquake intensities. In addition, this paper includes a discussion of strain amplitudes induced by environmental forces, the predominant causes of damage to structures. Also, certain popular myths regarding blasting damage are discussed in the paper. Due to space limitations, the paper will not include a discussion of airblast effects.

Jan 1, 1989

By S. Evans, J. Phillips-White, D. Morton

The partnership between Orica and MMG at the Dugald River Zinc mine in Australia has led to the first global field trials and deployment of Orica’s Subtek™ 4D™ (hereafter referred to as 4D) Bulk Systems underground bulk emulsion blasting technology. This technology offers advantages over conventional bulk explosives by extending the range of energy and length of explosive column that can be charged in underground production. 4D gives blast designers energy options between Relative Bulk Strength (RBS) 50 - 150, delivered uniformly along the entire column in most blasthole conditions along with the ability to instantaneously modify the energy within an individual blasthole. During Phases 1 – 3 of the project from October 2022 to January 2023, over 57 tonnes of the 4D Underground emulsion were loaded in 17 stopes. The primary objectives of this phase were to reduce hanging wall dilution and improve stope recovery. While drilling and other parameters remained unchanged, the energy selection was tailored for specific situations, guided by a revision to the site's drill and blast standard. The design used low energy (RBS 50 - 70) in holes adjacent to the hanging wall and high energy (RBS 130 - 150) where stope recovery had historically been challenging, such as at the toes of long downholes. Initial results of the project focused on five stopes selected for their similarity to those used for the baseline data set. Although the 4D data set was small, the post-blast scans indicated favourable results for recovery and dilution. This suggests that selecting and delivering bulk explosive with tailored energy levels can improve stope performance.

Jan 1, 2024

By Cathy Aimone-Martin, Kristin Dunlap Kolden

Blasting was conducted for the Army Corps of Engineers (Corps) in the Columbia River near Saint Helens, Oregon during 2009 and 2010 to deepen the navigation channel as a final phase of a dredging project to accommodate larger container ships. The Columbia River Channel Improvement Project (CRCI) required 4 months to blast and dredge 300,000 yd3 (229,366 m3) of basalt from the bottom of the channel to allow Post-Panamax vessels with drafts up to 50 ft (15.2 m) access to the Ports along the River. Explosives charges were limited to 90 lbs (40.8 kg) per delay for the protection of fish and marine life in the area. A fish mortality study and marine mammal monitoring program was also required by the Corps. Underwater overpressure monitoring was required for each blast and peak overpressures measured 10 ft (3.1 m) above the river bottom 140 ft (42.7 m) from the closest blast hole were not to exceed 70 psi (483 kPa) with a cautionary level of 40 psi (276 kPa). Specifications required sampling rates of 500k S/s and PCB Peizotronics tourmaline pressure sensors. The Corps granted permission to co-locate additional ceramic-type sensors at different sampling rates to design redundant monitoring systems 140 and 300 ft (42.7 and 91.4 m) from blasting and develop a site-specific overpressure attenuation model for the project. This paper presents the correlations of overpressure with cube-root scaled distance factors, a comparison of measurements using three different pressure sensor systems, and a discussion of blast design influence on overpressure measurements.

Jan 1, 2014

By Robert C. Fouchard, Gordon Chalmers, David E. G. Jones, Ivana Alilovic, Phillip D. Lightfoot

There have been numerous international instances over the last several years in which pumping emulsion explosives has resulted in accidents, apparently as a result of increased thermal sensitivity under these conditions. The key questions for the explosive industry are (1) what are the parameters that influence the sensitivity of emulsion explosives and, (2) how do these various parameters interact. To address the sensitivity of emulsion explosives to various parameters, a study was undertaken using an accelerating rate calorimeter (ARC) and a heat flux calorimeter (HFC). The effects ofthe addition of ammonium nitrate (AN) prills and different grades of aluminum (Al) on the thermal behaviour of emulsion explosives were determined. Additionally, changes in pressure, atmosphere (inert or oxidizing) and sample vessel material were assessed for their impact on thermal sensitivity. Addition of AN prills, fine granular Al or atomized Al did not affect the onset temperature for exothermic decomposition, so that the maximum “safe” temperatures for emulsions containing these additives will be similar. There were differences in the rates of self heating, however: AN prills decreased the rate of self heating, whereas atomized Al increased it. The emulsion formulations containing atomized Al produced small holes in titanium vessels. This phenomenon did not occur in Hastelloy C vessels, providing a reminder that materials of construction need to be carefully considered for equipment used to manufacture or handle emulsion explosives.. Both ARC and HFC experiments gave lower onset temperatures in air than in argon. We attribute this to oxidation of the oil phase by air. This result is significant for dry-running pumping conditions, where emulsion is heated in the presence of excess air.

Jan 1, 2000

By Dr. Zach Agioutantis, Elliott Morgan

The explosives, mining, and heavy civil industries consistently battle the uncertainty that is associated with working with a heterogenous medium like rock in blasting. This has led to studies to increase fundamental understanding of material response under dynamic loading that is associated with blasting. This study looks at the dynamic strain associated with blasting the lab Split-Hopkinson Pressure Bar (SHPB) testing while also building off of previous studies with the goal of better understanding the dynamic forces that are enacted on a geologic body during a blast loading event. This is required in order to advance geologic blast response modeling. This is achieved through analyzing the stress and strain values for each specimen that are calculated from strain data collected with a SHPB. Based on this data, the dynamic material response characteristics are able to be determined. Tests were conducted on five Berea Sandstone specimens with a rough length to diameter ratio (L/D) of 1.0. The strain data from these tests were then used to create stress strain curves as well as charts depicting failure stress to both strain rate and failure particle velocities. The tests conducted returned similar results to previous tests results on Berea Sandstone while also showing a correlation between strain rate at failure and failure particle velocities. While further research is needed, there is evidence that SHPB test data could be used in conjunction with the MBF model. The MBF model states that the peak particle velocity (PPV) of blast vibrations can be correlated with deformation (strain) at a given point. With a further understanding of dynamic material response correlated to PPV measurements, further refinement could allow for better prediction of blast performance.

Jan 21, 2025

By Piyush Rai

Proper use of fi ring pattern vis-à-vis the blast requirements can provide optimal blast performance in terms of fragmentation. Further to this, each fi ring pattern has its own characteristic, for instance, although V-type and diagonal fi ring pattern provide same Se/Be ratio, the V-type fi ring pattern increases the opportunity for in-fl ight collision amongst broken rock fragments during their movement. Similarly straight V-type and skewed V type fi ring patterns (V1,V2 etc.) have their own characteristic strengths and weaknesses. In this light the present paper highlights the application of three different types of fi ring pattern on two different type of sandstone overburden benches of a large coalmine in India. The study reveals that Firing pattern infl uences the effective spacing to burden ratio at the time of detonation. By changing the fi ring pattern, effective burden (Be) changes and the ratio of effective spacing (Se) to effective burden (Be) during the fi ring is also subject to change in comparison to drilled spacing to burden ratio (S/B) Hence, the Se/Be ratio vis-à-vis fi ring pattern must be used to design the blast rounds. The results have been derived on the digital image analysis based fragment size characterization, excavator performance and evaluation of powder factor values on blasted muck piles. Skewed V- type fi ring yielded the best results in comparison to straight v-type and normally practiced diagonal fi ring pattern on the moderately strong sandstone benches, whereas, the existing diagonal fi ring pattern appears to be satisfactory on weak (weathered and gritty) sandstone benches. The presence of geological anomalies has also been investigated.

Jan 1, 2008

By Martin Langenderfer, Sergii Chertopalov, Catherine Johnson, Vadym Mochalin, William Fahrenholtz

The high temperature and high pressure of an explosive detonation can be used for the production of nanomaterials. The controlled detonation of explosive compositions along with the collection and characterization of reaction products encompasses a process known as detonation synthesis. The primary advantage of the method of detonation synthesis is the possibility for producing monocrystalline nanoparticles with diameters of less than 10 nm. In order to successfully synthesize nanomaterials via the detonation process, it is necessary that the explosive detonation is conducted in a sealed environment. This environment when pulled to a vacuum or purged with inert gas such as argon will reduce the oxidation of detonation reaction products. Detonation synthesis testing is currently being conducted in a 1.8 cubic meters (m3) (64.3 cubic feet (ft3)) ellipsoidal pressure vessel consisting of two interlocking half shells. The testing involves the controlled detonation of cast mixtures of Cyclotrimethylene-trinitramine (RDX) and 2,4,6-Trinitrotoluene (TNT) in conjunction with siliceous compounds to produce nanocrystalline diamond and silicon carbide. Alternative detonation environments including the presence of a cooling medium such as water or dry ice to absorb residual, post detonation, thermal energy and enhance the stability of the materials being produced have improved yield. Modifications to the explosive charge composition have an effect on the type and quantity of materials that can be produced. Doping of explosive charges with various organic and inorganic compounds has shown promise in the synthesis of materials that are difficult or uneconomical to produce through other methods. This paper outlines the process development of detonation synthesis facilities. Preparation of the pressure vessel to create a suitable detonation environment for the production of nanomaterials is examined. Formulation of explosive charge compositions and considerations involving test charge initiation are discussed in detail. Experimental results and analysis from initial testing as well as plans for future research are also evaluated.

Jan 1, 2018