Search Documents

By M. S. Eygi

This study covers the investigations based on the electrokinetic and rheological properties to explain the interactions between kaolin minerals and commercially available polyelectrolyte in anionic character. Additional adsorption test were also conducted to support the interaction mechanism. Adsorption tests showed that adsorption densities decrease by increasing the solid content. In-creasing the solids contents from 1% to 30% by weight resulted in the decrease on adsorption from 2.14 mg/g to 1.85 mg/g. Because of its difficulty, the solids ratio at 70% was not studied. However, following to trend of the curve plotted adsorption density-solid ratio, an estimation was made and adsorption density at 70% solid content was extracted from the curve as 1.75~1.80 mg/g. The electrokinetic studies pointed out that the presence of polyelectrolyte increase the zeta potential of kaolin from 40 mV to 60 mV which is reasonable conditions to disperse and stabilize the kaolin slurry and lower the viscosity. When these result of the different tests are combined and considered together, 2 mg/g polyelectrolyte concentration was noted as optimal concentration where adsorption density, viscosity and zeta potential of the slurries give maxima and remain constant after this concentration.

Jan 1, 2014

By Kazutoshi Haga, Atsushi Shibayama, Altansukh Batnasan

The objectives of this study were to propose a viable alternative method for recovery of precious metals such as gold (Au), silver (Ag) and palladium (Pd) from waste printed circuit boards (WPCBs) and to regenerate the spent lixiviant solution for reuse. The proposed method generally consists of several steps as follows: 1). iodine-iodide leaching for metals extraction; 2). separation and recovery of precious metals and metal impurities from a pregnant leach solution; 3). regeneration of the spent iodine-iodide solution/lixiviant. In this method, more than 99% of Au leaching was achieved in the iodine-iodide solution from the solid residue of WPCBs that was obtained via sequential processes including incineration at 800 ?C and high pressure oxidative leaching with a diluted sulfuric acid at 120 ?C, while the leaching of Ag and Pd was less than 1%, respectively. Besides Ca, Cu, Ni, Co and Zn as main metal impurities, leaching efficiency of other metals did not exceed 1%. The precious metals and base metals as metal impurities present in the pregnant leach solution were separated and recovered by precipitation using L-AA and NaOH solutions. About 99.8% Au, 81.7% Ag and 72.8% Pd were recovered from the pregnant solution at pH of 2 with the addition of 0.1 M L-AA as precipitating agent. The remained small amounts of precious metals and metal impurities were precipitated at pH 13 using 1 M NaOH. The spent lixiviant after sequential precipitation was regenerated in the presence of hydrogen peroxide, hydrochloric acid and potassium iodide. It was revealed that over 90% of gold could be extracted from the residue of WPCBs with the regenerated lixiviant solution.

Jan 1, 2018

By Nirmal S. Weerasekara, Malcolm S. Powell, Mohsen Yahyaei

"An understanding of the fundamentals of different breakage mechanisms is critical for successfully modelling comminution processes. Due to the high frequency of low energy collisions in the grinding process, superficial breakage has a significant role in size reduction in mills. To develop a scaling up methodology for characterising low energy surface damage behaviour of ores, a series of surface damage tests have been conducted using three grinding mill sizes with diameters of 1.8, 1.2, and 0.8 m. Two types of gold-copper ore with different hardness were used: C-ore and T-ore. All tests were conducted using wet mode to remove the products during grinding. To ensure low energy surface damage was the dominant mechanism, in all tests the mill speed was reduced to 40% of critical speed. A surface damage index normalised with product mass and surface based specific energy is determined from the results enabling a study of the grinding performance regardless of mill size, energy level or charge mass. Incremental breakage tests using the JKRBT indicate that the A×b values of the T-ore were 60% higher than C-ore, suggesting the T-ore is considerably softer. The fractional mass loss rate for the T-ore in the 0.8 m and 1.8 m mills started from 16 and 7 (1/kWh/m2) while for the C-ore it was 4 and 2 (1/kWh/m2). After 6 minutes the surface damage index in all tests tends towards steady state a constant value, an indication of steady state surface damage condition. It has been demonstrated that this methodology can be a useful basis for characterising superficial breakage behaviour of ores."

Jan 1, 2014

By Érica Linhares, Anderson Silveira Lopes, Aline Costa

In the production units of ferromanganese alloys wastewater are generated. They mainly arise from gutters of drainage water from warehouse of raw material (manganese ore, reducing agents and other), product and slag. This wastewater, in general, may contain particles that will suffer difficulty to naturally decant, giving the water turbidity and color characteristics. Thus, this study aims to characterize the effluent, the treated water and the sludge from the sedimentation tank from the one main Brazilian plant. The investigated characteristics were: turbidity, total solids (TS), suspended solids (SS), dissolved solids (DS), pH, Eh, COD (chemical oxygen demand), residue classification and chemical analysis by ICP - OES. The turbidity before treatment was 417 NTU and after passing through the tank, 44 NTU, a figure slightly higher than the emission standards for Class 1 regulated by the Brazilian environmental legislation in force. The values for TS, SS and DS of the effluent were 225, 114.3 and 110 mg/L, respectively. For the treated water the values were 93, 48.3 and 45 mg/L for TS, SS and DS, respectively. The sedimentation process was able to reduce by 21 % of the COD. In the test of loss on ignition (LOI) from the tank bottom sludge were observed losses of 29.35 %, while the volatile analysis found 20.70 % of volatiles in the sample. It was determined that the concentrations of Al, Fe, Mn and S are, respectively, 0.1875 mg.L-1, 0.3071 mg.L-1, 0,789 mg l-1 and 0.00828 mg.L-1, values above the maximum allowed by law. Based on the analysis of X-ray diffraction, the identified minerals in the sludge were quartz, muscovite, kaolinite, calcite and albite.

Jan 1, 2014

By Victor V. Karmazin

"The appearance of the precise equipment for analysis of results of the laboratory tests with using of the computer processing allows raising accuracy of the estimation of the expected indexes of the mineral processing. Certainly, laboratory tests will not be able to substitute completely industrial ones, but allow reducing the amounts of the industrial tests, that vastly reduces the cost of technological forecast and preparation of data for projection.Calculation of the potential indexes of mineral technology (mass yields and the metal content in products) is fulfilled on the base of results of measurements of the mineralogical liberation parameters using special formulas.The quality of the concentrate ßc = a + ?l • ?s • ?i (ßt - a) can be achieved on a level of the theoretical metal content of a mineral - ßt only if coefficients of mineral processing, of liberation ?l and selectivity ?s of grinding, effectiveness of separation, will reach 1 (a - metal content of the row ore).Increase ?l by overgrinding automatically decrease ?s, and only by destroying of particles of ore along surfaces of accreting of minerals (?i = 1) and when values of all three coefficients will aim to 1, then ßc ? ßt.The degree of liberation of the useful mineral is the ratio of mass of free grains of the useful mineral in the product to general mass of the same mineral in this product. The factor of the liberation, which is defined by curves of dressability by angle of slop of the curve of the elementary faction - ?, is Kr=1 – tga. Kr changes from 0 to 1 when a changes from 45o to 0o. The liberation is reached by grinding of the material, although degree of the liberation, as a rule, is lower than the degree of the grinding."

Jan 1, 2003

The Arctic is a region of special economic, geopolitical, research, socio-ethnic, and defense interests of both Russia and other countries of the Arctic zone. Introduction of innovation technologies at ore-processing factories is a direct responsibility of the state and this problem should be solved on the basis of coordination of interests of different stakeholders. The task of elaboration of scientific principles of rational state regulation in the North is very topical. Innovations require considerable investments first of all from private capital. However as an investment object innovations are not attractive for investors as they require large expenditures for long-term projects, and they are connected to high risks because market incentives form striving to get quick profits of private companies and result in a certain behaviour strategy while innovations need ?long money?. Under such conditions without state regulation of investment and innovation activities development of the mining sector in the Arctic practically has no prospects. At innovation development of mining enterprises economic growth is provided at the expense of active state innovation activities. The elaborated strategy of ore-processing enterprises should correspond to the modern paradigm of the ore-processing industry development which is not only for extraction of minerals but also for multi-profile structure having comprehensive use of the resources on the rational basis intended for rational complex utilization of mineral resources of the AZR which by the definition includes maximally full use of the whole aggregate of resources on the economically rational basis with obligatory environmental with resource reproductive and socio-economic functions and deterrents. The main principle of creation of innovation technologies is to obtain more products of higher quality with minimal costs. This allows increasing ?productivity of the resources? several times. This principle makes increasing productivity of the resources the most important and in this case efficiency of use of the resources brings extra profits at the expense of lack of new costs such as payment for protection and utilization of wastes. According to the economic theory only ratio between demand and supply is able to fix optimal proportions in economy and to give necessary signals for investment activities of mining enterprises. In this context market for minerals and increase of mineral resources productivity do not create incentives for investment activities without which neither sustainable economic growth nor solution of macroeconomic tasks are possible. Nevertheless countries should not reject this idea in spite of economic efficiency of the enterprises. Extraction degree of useful components and especially oil in the Arctic zone is one of the lowest in the world. This can lead to crisis of oil industry and other mining sectors. The reason for that is lack of a state policy of realization of innovation technologies in the mining sector in the Arctic.

Jan 1, 2014

By A. Güney

Currently, recycling technologies use relatively homogeneous plastics because hand-sorting waste feed is too expensive. Many promising technologies for separating mixed thermoplastics are being investigated, but they are still uneconomical and unreliable. Burning plastics for recycling is not used because of poisonous gases released when their burning. PET and PVC cannot be separated using conventional gravity separation techniques because their specific gravities overlap; PET density changes from 1.33 g/cc to 1.37 g/cc and PVC density is between 1.32 g/cc and 1.37 g/cc. For this reason, plastic recycling needs new techniques. Among these techniques froth flotation, also used in mineral processing, can be useful for its cost and simplicity. In this method, a plastic is selected from mixture, tried to regain its natural property, hydrophobicity. In this study the experiments were applied by using plasticizer reagents to make the selected plastics hydrophobic and us-ing NaOH to render the other hydrophilic. Post-consumed PET and PVC are evaluated by concerning the effects of selected parameters (particle size, concentration of plasticizer reagent, amount of NaOH, conditioning time and the effect of conditioning temperature). At the end of the experiments, optimum parameters for selective flotation of PET from PVC was found as particle size of -4.76 + 3.36 mm, NaOH amount of 30 kg/t, conditioning temperature of 75°C, conditioning time of 30 minutes, reagent amount of 300 mg/L. Consequently, PET was re-covered with 99.7% purity and 57% efficiency.

Jan 1, 2014

By Rodney J. Hundermark, Sharif Jahanshahi, Shouyi Sun

"The major platinum producers in South Africa make use of electric furnaces for the melting of platinum group metal (PGM) bearing nickel – copper concentrates. To gain better understanding of the furnace operation, research was conducted at CSIRO Minerals in Melbourne, Australia. One aspect of the research project was the investigation of the factors affecting the electrical conductivity of melter type slags.Electrical conduction in slags can occur through two mechanisms: ionic and electronic. There is good understanding of the ionic mechanism. In slags containing high levels of iron, the dominant mechanism is electronic as a result of charge hopping (electrons or holes) between ferric and ferrous ions. There is limited understanding of the electronic mechanism and one of the aims of the research was to investigate this mechanism further.Experimental work was carried out at 1450 °C on Al2O3–CaO–FeOx–MgO–SiO2 slags similar in composition to the melter slags (typical composition range (wt%): Al2O3: 5, CaO: 5-15, FeOx: 10-30, MgO: 15-25, SiO2: 40-60). The approach was to vary the oxidation state of three different basicity slags and measure the conductivity response. The slags had molar (CaO+MgO)/(Al2O3+SiO2) ratios of 0.43, 0.64 and 0.94 and FeOx contents of up to 40wt%. A twoelectrode technique was employed with a shallow layer of slag contained in a magnesia crucible. The small amount of slag facilitated relatively quick equilibration (up to one hour) with the gas atmosphere. Experiments were typically started in air and sequentially reduced using different ratios of CO and CO2 gases.Conductivity increased with increasing basicity and increased significantly with iron oxide content. Above 20wt% FeOx, electronic conduction was significant and the conductivity varied with the oxidation state of the slag. The typical response of the conductivity to the change in oxidation state was the following: starting in air, as the slags became more reduced, the electrical conductivity increased to a maximum at around pO2 = 10-7 to 10-4 atm and then decreased with further reduction. The value of the pO2 at which the maximum occurred was dependent on the total iron oxide content and basicity of the slag. The magnitude of the conductivity of the slags increased with increasing FeOx content in a range of 20 to 170 S/m for 20 to 40wt% FeOx. For a given FeOx content in the slags, the oxidation state dependence of the conductivity varied with slag basicity. The trend observed was that the maximum in the conductivity occurred at higher oxygen partial pressures for the lower basicity slags."

Jan 1, 2003

By Hideki Yamamoto, Norihiro Murayama, Junji Shibata

"Hydrothermal syntheses of zeolite from coal fly ash were carried out by using various alkali sources. NaOH, Na2CO3, KOH, K2CO3 and their mixture were applied for an alkali source of zeolite synthesis. The various physical properties of the reaction product, such as the kind of zeolite crystal, cation exchange property, surface texture and so on, was investigated through the zeolitization reaction from fly ash. The mechanism of zeolitization reaction was considered from these results.Zeolite P(NaP), hydroxysodalite(HS) and chabazite(K-CHA) are synthesized as zeolite species, when fly ash hydrothermally reacts in various alkali solutions at 393K. The crystal structure of the products obtained in NaOH solutions for 3h changes from NaP to HS with increasing NaOH concentration. K-CHA formation in KOH solutions needs 10h of reaction time, which is longer than that of NaP or HS.Dissolution, condensation and crystallization steps exist in the zeolitization reaction from fly ash, and the particle surface of products remarkably changes in each step. The fly ash is spherical particles and the surface is smooth(Fig.1(a)). The dissolution of fly ash occurs in the heating process until 393K, and the particle surface changes like unevenness(Fig.1(b)). In case of NaP, the condensation of aluminosilicate ions takes place at 373-393K, and the amorphous aluminosilicate is deposit on the unreacted fly ash(Fig.1(c)). The crystallization of NaP already begins to occur at 393K and the surface is covered with fine zeolite crystals for 24h(Fig.1(d))."

Jan 1, 2003

By P. A. Harvey

Previous studies have reported that inorganic electrolytes can enhance floatability of coal. The research has shown that the enhancement, if any, is highly dependent on changes in solution pH, type of electrolyte, and electrolyte concentration. The reasons for this are still not clear. In this study the floatability of coal particles in mono and divalent salt solutions was investigated. The zeta potential and hydrophobicity of the coal was measured experimentally, and a modified Hallimond tube was used to determine the floatability of coal particles by single bubbles, where the collision efficiency was equal to unity. The experimental information was used in conjunction with the Hogg-Healy-Fuerstenau equation to quantify the electrical double layer interaction. It was found that for low electrolyte concentration (less than 0.1 M) solutions the flotation recovery of coal particles was less than that for distilled water, and decreased with increase in concentration. Conversely, at electrolyte concentrations above 0.1 M, flotation recovery increased with increasing concentration (Figure 1). Both of these results are consistent with previous observations, but are inconsistent with expectations when considering the possible influence of electrical double layer interaction. Modelling of the system indicates that the electrical double layer is compressed with increasing electrolyte concentration, resulting in an increase in flotation recovery due to a diminishing of the (electrical double layer) repulsion between the bubble and the coal particles. Moreover, for electrolyte concentrations above about 0.1 M the electrical double layer is completely depressed and would have little further influence, if any, on the flotation process. Therefore, the electrical double layer interaction is not the principal determining factor for the flotation of coal in electrolyte solutions.

Jan 1, 2003

By J. D. Miller, C. L. Lin

In general, x-ray computed tomographic (CT) techniques are able to provide 3D images of the internal structure of opaque materials in a nondestructive manner. The unique cone beam geometry allows acquisition of all 2D projections with only one rotation of the sample thus providing for fast data acquisition and better x-ray utilization, as a complete 2-D detector array receives the cone-shaped flux of rays. Thus, an isotropic 3D volume can be reconstructed without the mechanical translation and the stacking of sequential slices as is the case for more conventional CT scanners. In this regard, a state-of-theart, custom designed x-ray microtomography facility to provide very detailed 3D spatial analysis of multiphase particles has been installed and is in operation at the University of Utah. The reconstructed 3D tomographic volume allows for an adjustable spatial resolution from 5 to 20 microns for sample dimensions from 10 to 40 mm in diameter, respectively. For example, a packed bed of coal particles is shown below in which different crystalline froms of pyrite are distinguished in 3D.

Jan 1, 2003

By Jia Muxin

The adsorption behaviors of metal ions on a silicate mineral and the flotability of a metalized silicate mineral with sodium oleate as collector are closely related to the structure of the silicate mineral. The adsorption isothermals of the metal ions on different silicate minerals are studied, the parameters of the isothermal give the information how many surface oxygen anions a metal ions is attached to, from this information and the structure of the mineral the site where a metal ion is attached can be guessed (The adsorption isothermals and adsorption behaviors with pH are fitted with Temkin, Frenudlich and Kurbatov equations respectively). Metal ions as Cu2+, Ni2+, Zn2+ are attached to the oxygen anions of surface species –Si-O– on the quartz surface, most of them coordinate to only one surface oxygen, their adsorption ability on quartz is low, but this metal ions on quartz surface protrude out of the surface perfectly, so their ability to combine with oleate acid radical is excellent. Quartz can be activated well by such metal ions. The isothermal of Fe3+ on quartz indicates these cations coordinates with more than two surface oxygen anions. This means the Fe3+ nucleates on quartz surface in the form of Fe(OH)3 colloid particles. The isothermals of Cu2+, Ni2+, Zn2+ Fe3+ on spodumene shows such ions coordinate with more than two surface oxygen anions, it indicate these ions may attach to the position where Li+ is formerly exists, such metal ions stay in a cave on the mineral surface, their adsorption abilities on spodumene are quite well, but they are affect by the oxygen anions of the two Si tetrahedron chains, the can almost not activate this mineral. These cations may attach on the site where Al3+ exists on the muscovite surface, just like spodumene, muscovite can not be activated well by such cations. Pt2+ has a large ion radius, as Pauling’s rules depicts polyhedron can not attach to Si tetrahedron well, the adsorption ability of Pt2+ on quartz is low and quartz is activated badly by Pt2+. On the other Pt2+ can adsorb well on spodumene and muscovite well and activated them well because it is not affected so bad by the tetrahedron oxygen anions of the minerals for their its large radius. The isothermal of Ca2+ on quartz indicates a Ca2+ coordinates with less than one surface oxygen anion, this means Ca2+ attaches on quartz mainly by physical adsorption. The adsorption abilities on mineral surface and the interaction abilities with oleate acid radical of the transition metal ions with the same valence are guessed to be determined by their d electron number, the rules should be d1<d2<d3<d4>d5<d6<d7<d8<d9>d10. Hydrogen bond may play an important rule in the activation of the mineral by HF and the interaction of the HF activated silicate mineral with collectors. The general rule is high bond valence and small metal ion radius surface species –Me-O can be activated well by HF with sodium oleate as collector. For example – SiIV-OH is neutral while –SiIV-FH+ and –SiVI-FH+0.33 are positively charged, the positively charged surface species are more likely to connect oleate acid radical via hydrogen bonds.

Jan 1, 2003

By Gus Van Weert, Samuel A. Bolorunduro, David B. Dreisinger

"INTRODUCTIONAcid pressure oxidation of high-grade natural acanthite was investigated in the range of 110-150°C and in the sulphate media. High acidity and low pulp density were used to prevent the precipitation of silver.RESULTS AND DISCUSSIONTwo sets of acanthite specimens were obtained from La Valenciana and Ingleterra mines, Mexico. Pressure oxidation tests were conducted on 1 litre scale in a standard 2-litre Parr titanium autoclave.EFFECT OF TEMPERATURE ON THE REACTION OF ACANTHITEThe effect of temperature on the rate of oxidation is presented in Figure 1. The rate of reaction increased with increasing temperature."

Jan 1, 2003

By Filippov. L. O.

Metallurgical results for the copper-nickel disseminated ores were improved by using ultrasonic treatment. This has been demonstrated by processing of bubble-pulp flow in the reactor zone of a reactor-separator flotation machine. It can be explained by changes in mineral and size composition of the concentrates. Thus, the selectivity of Cu/Ni flotation for different values of the hydrodynamic parameter increases considerably. Additional effect of the ultrasound treatment has been noticed under conditions when the detachment of the gangue minerals from bubbles can be controlled. Reactor-separator has advantages over other types of flotation cells for this purpose. In fact, the weak diameter of reactors make more efficient the ultrasound effect than in conventional impeller or column flotation machines. A combination of ultrasonic treatment with original organization of gas pulp flux in the reactor-separator allows to obtain significant effects in the flotation attachment/detachment subprocesses, enhancing the process selectivity and/or recovery of substances. Increase of total recovery of copper and nickel into bulk concentrate at constant grade is 8.5% for coarse disseminated ores. For copper ore, copper recovery increased by 10% at unchanged grade of 11.7% and nickel recovery gained 17% at the constant grade of 2%.

Sep 1, 2012

By P. Prakash

A dual-drive planetary mill, which has a rotating shaft that sweeps a circle of diameter 750 mm, has been designed. The planetary mill is powered by a 5 hp motor to rotate the main shaft and a 3 hp motor to rotate the jars. The charge dynamics inside the horizontal-axis planetary ball mill was established using three-dimensional DEM simulations. The simulation results provided data to determine the impact energy distribution and the effect of process parameters such as mill speed and filling. It has been observed that the mean impact energy per unit time increases with rotation-to-revolution ratio, whereas the average number of inter-particle impacts per unit time decreases. The mill was also used to synthesize a variety of powders. Here three case studies of reaction milling are briefly presented: (i) cementite and silicon carbide, (ii) oxide dispersed strengthened (ODS) steel, and (iii) magnetite from blue dust. In each case, the powder was produced by mixing and then milling the corresponding pure components. The phase evolution, particle size distribution, and morphology of particles during milling were studied for various samples collected at different milling times using laser size analyzer, SEM, TEM, and Mössbauerspectroscopy. The results established a convenient way to produce powders of high technological and commercial value.

Sep 1, 2012

By Fu Ping-Hao, J-P Franzidis, Sergio Mauricio Vianna, Ewen Silvester, Emmy V. Manlapig

"Over the last 5 years, an ambitious project has been undertaken at the Julius Kruttschnitt Mineral Research Centre (JKMRC) aiming to isolate, study and, if possible, model the effect of particle size, liberation and collector adsorption density on the floatability of mineral particles. As part of this project, we have conducted highly controlled flotation test-work, combined with state-of-the-art solution and surface analytical techniques such as High Performance Liquid Chromatography (HPLC), Time of Flight Secondary Ion Mass Spectroscopy (TOF-SIMS) and detailed mineralogical analysis to fully characterize the flotation behavior of a natural ore.The flotation tests were undertaken using a high-grade lead-zinc ore from BHP-Billiton's Cannington mine (Australia) in a specially designed continuously operated laboratory scale flotation rig. Solution and adsorbed collector concentrations were measured independently during the course of the flotation tests using HPLC based ex-situ techniques. Liberation studies were performed using the JKMRC Mineral Liberation Analyser (MLA) on selected size intervals of different streams to estimate the specific surface area of galena. These results were used to calculate the collector adsorption density (collector coverage) on galena particles, with the eventual aim of developing a mathematical model describing the relationship between pulp chemistry, feed mineralogy, and floatability of galena particles."

Jan 1, 2003

By Luis Bergh, Francisco Díaz, Isabel Panire, Juan Yianatos, Luis Vinnett

"In this paper, industrial data of residence time distribution (RTD) in mechanical flotation cells is presented, which were measured in several plants using the radioactive tracer technique. Results include mechanical flotation cells of 100 - 300 m3, which were operated with effective residence times from 2 to 7 min. Tests were developed in forced air and self-aerated cells for liquid and solids (non-floatable) per size classes. Different RTD model structures including perfect mixer, Large and Small Tanks in Series (LSTS) and by-pass flow plus perfect mixer were evaluated and compared for single cells. The actual mixing regime was related to the effective residence times and cell designs based on the model fitting. By-pass flow percentages were typically lower than 10%, therefore the perfect mixer model plus a dead time was a suitable model structure in most cases. On the other hand, the arrangement of cells in series was effective in reducing the bypass flow observed in single cells (by-pass flow percentage greater than 5%). In addition, the N perfectly mixed reactor in series model was used to represent the mixing regime along flotation banks, which were operated with mean residence times in the range of 18 - 53 min. Results showed that N tanks in series plus dead time were closer to the actual values in most cases."

Jan 1, 2014

By D. B. Sundar Ramam

In the recent past, a paradigm shift in terms of resource utilization and beneficiation practices is experienced by the Indian mining and mineral sector. Depleting iron ore reserves coupled with increasing demand for low-alumina iron ore fines to improve blast furnace performance in terms of productivity and reduced slag rate necessitate intensive beneficiation of iron ore. The task is even difficult for Indian iron ores, which are generally high in iron content and at the same time characterized by aluminous gangue. In 2006, M/s Tata Steel commissioned a state-of-the-art Jigging Plant (Batac Jig) at Noamundi Iron Mine (NIM), mainly to reduce alumina in iron ore fines. The jigging plant is incorporated in the existing beneficiation circuit to treat ?10+0.5mm size fraction of classifier fines. Over the course of plant stabilization while the plant could deliver desired ore upgradation and average product alumina, variability in terms of alumina content has been a concern. This paper discusses a case study of process parameters optimization in jigging operation to achieve consistent product quality while improving the effectiveness of gravity concentration for the beneficiation of Noamundi iron ore also to take care of inferior plant feed (input) grade year on year. The operating variables used to optimize jigging operations include bed height, pulsion and suction time, particle size, strokes, and plant throughput rate.

Sep 1, 2012

By Y. Nahmad- Molinari

We present a novel on line inductive sensor for the determination of the quality of the concentrates of iron ores. This device is coupled with a cheap USB Data Acquisition System that makes it versatile enough to simultaneously control up to seven fluxes at a very low cost (< $300 US dollars), and achieves a resolution better than 0.5 % on the determination of the magnetic iron content in the concentrate. A RLC circuit with its inductive element placed surrounding a sample of pure magnetite concentrate is tuned at its resonance frequency, by means of adjusting, the feeding voltage of a voltage-controlled oscillator (VCO) and several samples with mixtures of different contents of silica and magnetite are placed in order to get a calibration curve. After some signal conditioning, a National Instruments USB-DAQ NI-6008, acquires the amplitude of the signal via USB port on a PC using a Lab-View program designed for such purpose, in which the calibration curve is used for on-screen data presentation directly in percent of magnetite content. The implementation of this device for control purposes on line directly placed on the concentrators would allow better efficiency of the process and higher quality of the final concentrate by con-trolling; the rotation speed, the rising or dilution water fluxes or bypasses towards milling recirculation cycles.

Jan 1, 2014

By Hakan Gürsoy, Kemal Bilir, Bahri Öteyaka, Ali Uçar, Oktay Sahbaz

"Jet diffuser flotation column (JDFC) is a flotation device resembles Jameson flotation cell (JFC) in terms of operational principles, but it has significant difference structural points of view. This difference is an essential change in the downcomer to provide an increase of performance of the cell for the coarse particles. By using the hydrodynamic and fluid mechanics principles (Sahbaz et al., 2013) downcomer was changed as a diffuser, therefore turbulence at the end of the downcomer was reduced to provide better aggregate stability and homogeneous dissipation of the bubbles in the separation tank. According to experimental results carried out in pilot scale JDFC, not only higher flotation performance comparing with Jameson cell was obtained specifically for coarse talc particles in a certain condition, but also quiescent froth layer was acquired. In these tests, vertical pipe of JDFC having inlet diameter of 6 cm and outlet diameter of 11.5 cm was used with separation tank having the diameter of 39 cm. By using the data, pilot scale JDFC having 410 cm vertical pipe integrated with separation tank was produced and flotation tests were carried out by using the naturally hydrophobic mineral (talc). Finally, the talc recovery obtained as 94% by the use of JDFC, while Jameson cell has the recovery of 77% for the particle size of 250 µm."

Jan 1, 2014