Search Documents

By Garland Likins

High strain PDA testing has become common for verification of capacity of both driven and bored piles. It is equally applicable to Augered-Cast-in-Place (ACIP) Piles. It also evaluates other aspects of the installation such as integrity. The benefit of high strain dynamic test results for the relatively low cost of the tests compared to conventional static testing has resulted in widespread use. The method is described and specific procedures for testing ACIP piles are outlined. Example results demonstrate the application.

Jan 1, 2000

By Sam X. Yao

In construction of drilled shafts under water, placing concrete in the shafts is technically demanding and involves complex construction logistics. Past construction experience has demonstrated that high quality concrete can be placed in drilled shafts under water with a proper concrete mix and proper placement techniques. However, a significant number of failures have occurred which have resulted in excessive cost overruns and delays. These problems may have occurred because proper underwater concrete construction techniques have not been widely disseminated within the industry. This is a technical area where competent design and sound construction planning can achieve a significant reduction in both risk and cost. This paper will discuss some key technical issues in the concrete mix design, concrete production and placement for the drilled shaft construction. The paper also describes two lesson-learned case histories from drilled shaft construction projects.

Jan 1, 2013

By Alan Alhadeff

Why is mediation being hailed as the wave of the future? The high cost of putting on a trial, over-crowded court calendars and long trial delays have resulted in what prominent attorneys and leading jurists are calling a litigation crisis. In no segment of the legal world are these pressures greater felt than in the trial of the serious construction case. Furthermore, the siege mentality of both the plaintiff and defense bar often leads to a reluctance by either side to make the first reasonable offer for fear of showing weakness. Attorneys operating in the serious construction case arena express concerns that there exist insufficient opportunities for the parties to meet, tell their stories, and negotiate settlement prior to the eve of trial. Mediation, by opening lines of effective communication and encouraging meaningful settlement negotiation, has proven to be a very effective antidote to the litigation crisis.

Jan 1, 1990

By Matthew Janes

The RC Harris Filtration Plant, which treats the majority of the fresh water for over 2.5 million Torontonians, is a Canadian Architectural Heritage site demonstrating a classic example of Art Deco Architecture. The facility is undergoing an expansion to install an underground sludge treatment capability. Perched atop a bluff on the North shore of Lake Ontario the structure enjoys a commanding presence on the Lake Ontario shoreline. A series of underground tanks were proposed for the hillside below the structure, which when covered would preserve the building?s architectural presence. However, the plan required two, stepped excavations 12 m and 10m deep into compact, wet sands over stiff clays and clayey silts. Concerns regarding the original structure influenced designers to set the lateral deflection limit for the front footing of the existing structure at 4 mm, (0.03% excavation depth). The design-build team indicated at the time of tender that the movement criteria was unattainable using the tender design. Analysis indicated installation effects and overall elastic movement of the soil mass beneath the building would result in movements of 7 to 9 mm at the structure. Through extensive FLAC analysis and a novel construction geometry the design-build team crafted an alternative that produced significant savings over the original concept. Based upon the analysis the design-build team negotiated a new deflection criteria dictating a maximum of 2.0 mm of movement across the critical expansion joint between the Filter Building front footing and the tank slab beyond. The contractor invested in additional pre tender soils investigation to support the refined design process. The FLAC analyses indicated the Filter Building movements would be elastic and distributed up to 50 m back beneath the front footing of the structure. An extensive precision monitoring program proved construction related movements of 6 to 10 mm horizontal at the front footing. Extensometers placed at two locations over the critical interior tank expansion joint showed no measurable movements. The overall monitoring program, including inclinometers, tilt meters, tie back extensometers (smart cables) and tie back load cells indicated a good match between recorded movements and loads and those predicted by FLAC Analysis.

Jan 1, 2006

By G. W. Plant

This paper describes the design philosophy and construction details of piles between 25m and 32m deep to support 160m high and 110m base diameter cooling rowers for a major power station. It is sited on deep expansive soil where a vast plantation of Eucalypts had been felled. The depressed water table is expected to rise, leading to swell of the soil and uplift forces on the piles. These forces, combined with the complex loading from the cooling towers, led to design tensile loads up to 20MN (2 000 tons) per pile. When competent stable material was present hand excavated underreams 3m in diameter were constructed for the piles sup-porting the shells. However, in some areas it was not possible to form an effective underream and an innovative solution was sought. This comprised unstressed dowels in the underlying sandstone which were formed by percussion drilling through void formers cast into the piles.

Jan 1, 2010

By Lucian Bogdan

On many occasions during construction and service life of the structure, it is crucial to know the load in post tensioning tendons and anchors. Although there are many methods to measure the tendon force, most of them are cumbersome, expensive and the accuracy differs depending on the method used Dyna Force sensor uses the Elasto-magnetic technology (EM) and non destructive testing (NDT) to direct measure stress level in prestressed strands or bars installed on ground anchors or post tensioning tendons. Dyna Force sensor can be used to rapidly read the change in load during proof and performance tests and compare with the pressure gauge and during the life on the anchor to monitor existing lock-off load. It can be used also to determine the load along the bonded length of the anchor allowing the contractor to increase or decrease this length. The paper presents Dyna Force operating principle and some applications. In conclusion, the Elasto magnetic technology applied through Dyna Force is a new and easy to use approach to monitor anchor load during proof test and service life of the structure.

Jan 1, 2009

By Frank Haehnig

Ground freezing is a technique which is used more and more in tunnelling under complex ground conditions. This paper will present three case studies which highlight different aspects of the ground freezing technique when applied in urban environment. The first project is the City-Tunnel in Leipzig, Germany, which is being built beneath the central station and which is the largest ground freezing project currently under construction in Germany. The second case study is part of the North-South-Line project in Amsterdam, Netherlands where ground freezing will be carried out to al-low the TBM drive through old wooden foundation piles. The freeze tubes for this project will be driven using Horizontal Directional Drilling (HDD). The last project is the Hallandsas Tunnel Sweden where the ground freezing equipment has to be installed against high water pressure. The paper illustrates that ground freezing can be implemented in difficult ground conditions such as soft ground, highly fractured rock and high water pressure. The case studies highlight the importance of good workmanship. With the increasing numbers of large tunnels being constructed in difficult ground conditions the paper concludes that the complex case studies presented will be-come more representative for future tunnel projects in urban environments.

Jan 1, 2008

By Cem Altuntas

This paper is the second in a series of two describing the design and construction of a foundation for a major high-rise real estate development on the west side of Manhattan, N.Y. The foundation members consist of large-diameter rock-socketed caissons, driven closed-end steel pipe piles bearing on rock, and a secant-pile retaining wall surrounding the entire site. This paper focuses on the Osterberg cell (O-Cell) load test completed for determining the allowable side-shear resistance between the concrete and the sides of the rock socket. Different qualities of mica schist bedrock, demonstrated by the penetration of rock with the soil auger or drill casing, were encountered. Accordingly, an additional subsurface investigation consisting of test borings at each caisson location was completed. Unconfined compressive strength tests were performed on representative rock samples. The ?soft? mica schist was observed to have vertical foliations and high mica content. For the first time in Manhattan, an O-Cell load test was performed to determine the allowable side shear resistance for both the soft and hard mica schist bedrock. The side shear resistance obtained from the O-Cell load test is compared with the side shear resistance allowed by the New York City Building Code and empirical correlations using unconfined compressive strength values for rock. The rock socket design for the caissons was refined based on the O-Cell load test results.

Jan 1, 2008

By J. G. La Fonta

The rapid development of real-time monitoring technology for the construction of large underground structures in urban areas can be attributed to: the zero-risk objective, the need for transparency between all parties involved and the control of real cost within the budget. Real-time monitoring can be an integral part of the construction contract (for example when compensation grouting is required) or independent, in particular when measurements of existing structures and buildings bordering the project are to be taken before construction starts. Three examples of extensive field instrumentation schemes are described: a large road tunnel in the Moscow suburbs, a new metro line in Amsterdam and major redevelopment works at a busy Central London rail interchange.

Jan 1, 2006

By G. Ranjan

The designers and the practicing engineers have started using latest and cost effective techniques of ground improvements which utilise the weak and poor sub-soil deposits efficiently for the civil engineering construction. In the present investigation, a new concept of 'skirted granular piles' has been advocated. An effective method of construction of granular piles as an economical alternative to vibroflot, and the skirt has been developed. The construction technique is based on indigeneous know how which effectively utilises the man-power technology avoiding import of costly equipment suiting to the developing countries. Full scale insitu tests have been carried out at four sites, having different soil conditions, on virgin weak sub-soil, and improved ground by casting plain and skirted granular piles. Effectiveness of different types of skirt has been demonstrated through insitu tests. A simple analytical approach has been proposed to predict the ultimate pile capacity. The predicted values of ultimate capacity have been found to demonstrate a good correspondance. Granular pile behaviour in terms of pile depth, diameter, spacing and stress deformation characteristics of the improved ground have been discussed. A significant improvement in ultimate capacity in improved ground has been noted. This is further augmented when granular pile group is skirted.

Jan 1, 2010

By C. O. Riggs

Geotechnical exploration in North America, in particular, exploration for deep foundations analyses, is currently and generally performed following the most basic sampling and insitu testing methods and techniques. Some would surely say that the state-of-practice severely lags the state-of-the-art. Probably more than 90% of all deep foundations, both driven piles and drilled piers, installed in North America are initially analyzed and designed, i. e. geotechnically, on the basis of either the soil penetration resistance obtained by performing the "Standard Penetration Test" (SPT), or from laboratory shear tests performed on samples obtained using 76-mm (3-in.) nominal diameter, thin wall, "Shelby tube" samplers. The use of design data obtained with other exploration methods and devices, such as bore hole pressure meters, flat plate dilatometers, even cone penetrometers, occur on the fringes of practice and often in conjunction with the use of the two simpler methods of analysis. This basic approach probably represents an attempt of the profession to use, as much as possible, common, easily understood and easily communicated procedures in all geologic environments. The characteristics of drill rigs with the required drilling and samplng tools vary somewhat from region to region in North America according to the physiography of the area of use, the types of exploration data required on a day-to-day basis, the philosophy of the engineers and geologists that use the exploration data and the financial resources of the drill rig owner. The physical capability of the exploration drill rig used on a project can have a significant effect on the quality of samples or insitu tests. The physical configuration and the quality of the drill and the drilling, sampling and testing tools not only provide the mechanical capability to obtain data but affect the attitude of the field exploration crew and the quality of work. This complete presentation is taken, for the most part, from a book in preparation for publication: "Geotechnical Exploration and Site Characterization" by C. Riggs, A. Hatheway and N. Schmidt. The book is scheduled for completion during 1987.

Jan 1, 2010

By Avi Shonberg

With the advancement of offshore wind farm projects towards deeper waters and larger wind turbine generators, founda- tion solutions other than the monopile have received increasing attention over the past 5 years. Monopiles are the most commonly used foundation solution for offshore wind turbines, with 82% in European waters founded on monopile foundations (EWEA, 2019). However, 2018 saw a record number of suction bucket jacket (SBJ) structures, which consist of a three-legged jacket sup- ported by a suction bucket at each leg (Figure 1), installed for offshore wind. applications. SBJs have now been installed successfully at the Borkum Riffgrund 1, Borkum Riffgrund 2 and Aberdeen Bay offshore windfarms. Suction-installed foundations, referred to in this paper as suction buckets, suction caissons, suction piles or suction anchors, have been widely used in the offshore industry since the early 1980s for a range of offshore applications predominantly as anchors for floating offshore structures - where they are "the most widely used anchor types for deep-water mooring applications" (McCarron, 2011). Suction buckets, installed using pumps that generate suction forces by creating a pressure difference between the inside and outside of the bucket, allow for the installation to be undertaken with minimal noise and without the use of mechanical force. Therefore, a key difference between suction-installed foundations and other foundation types is that the installation design, which must consider the soil type, soil strength and installation specific risks (for example, soil stratification with significant differences in permeability) may have a direct influence on the dimensions of the foundation. While the number of SBJS installed for offshore wind applications has increased significantly in recent years, the installation process for SBJ struc- tures is yet to become standard practice and is considerably more complicated than the installation process for mon- opiles. This paper provides a brief

Jul 1, 2022

By Walter E. Vanderpool

Type 1B micropiles (Bruce and Juran, 1997) can be installed rapidly and efficiently. During an 85-day period, 536 micropiles were installed to depths of 61 meters within a site 41 meters by 43 meters. Their performance, as measured by load test, varied even where the materials, construction procedure, and installation technique were closely monitored and controlled. The variation in displacement, as measured by the standard deviation, exceeded 50 percent of the mean test-load displacement for all loads up to the maximum load applied (2670 kN). This study provides a statistical basis to predict variability with respect to the construction method, micropile materials, and installation technique. The variability of displacement at all test loads is a fundamental characteristic of this type of drilled deep foundation system.

Jan 1, 2002

By S. R. Nandargikar

Construction of open foundations for the Second Thane Creek Bridge was indeed a challenging task. Some major problems were encountered during the construction of foundations for pier No. P22 (S/N), P.6(S) and P.12(S) of this bridge. This paper describes these problems briefly and also highlights how they were solved.

Jan 1, 1996

By Mark Johnson, Mathew Janes

"The Resonator RD 260 Resonant Pile Driver delivers ground disturbance free, high production pile driving. The Resonator has recently been used on numerous production pile driving sites in the Netherlands and Melbourne, Australia to drive piles in sensitive areas where conventional pile drivers could not be used. Two case histories are provide in this paper which demonstrate the features and benefits of Resonant pile installation.. In the Netherlands the Resonator RD 260 was used at the Vopak Oil Storage facility in the Port of Rotterdam to install pipe and sheet pile within an active pumping gallery. The site demanded vibration free pile installation to construct a cofferdam within sensitive, highly valued assets. Access was an issue and schedule demands were stringent as shutdown windows were narrow. The RD 260 provided ground disturbance free piling immediately adjacent to fragile structures. At Vopak the only site access was using a large crane positioned over 40 m from the location of pile driving. Driving was conducted amongst 900 mm dia pipes carrying heated crude oil.In Melbourne the RD 260 was used to drive GU 18 sheet piling adjacent to light rail easements. The project was the first of many grade separations being constructed within Melbourne urban areas to lower the light rail and provide quieter rapid transit. The original trial used an RGT MR105 series vibrator but noise and vibration criteria were exceeded. The RD 260 was brought in for a trial and performed with high production and produced negligible ground vibration. Up to 17 sheet piles 14 m in length were driven in a 2.5 hour window during the trial.IntroductionThe Resonant Pile Driving method is gaining acceptance around the world as a new method to rapidly drive piles free of ground borne vibrations. The high frequency vibrator resonates the pile, essentially turning the pile into a spring, to excite the toe of the pile with high accelerations and low amplitude. High acceleration with low amplitude generates high penetration rates but the high frequency stress waves are quickly dissipated in the soil. Typically ground borne vibrations are measured at below 1 mm/sec within 1 to 5 m of the pile. The Resonant method can drive a pile next to a glass of wine, without spilling, as has been demonstrated on numerous piling sites.How Does Resonance Work?The Resonant method uses a hydraulic piston - cylinder geometry to generate high magnitude, high frequency oscillating force. This is a very different mechanism than the eccentric mass technology used in conventional and variable moment vibrators.A unique valve geometry achieves the high frequency flow switching necessary to oscillate the hydraulic piston at up to 180 Hz (10800 VPM). The valve is controlled electronically for maximum accuracy of the desired frequency. The volume of hydraulic oil delivered through the valve to the piston (flow rate) determines the amplitude while the hydraulic pressure determines the peak force."

Jan 1, 1900

By Abolfazl Eslami, Fatemeh Valikhah

"Complexity in soil-foundation interaction and subsoil nonlinear behavior cause difficulties and uncertainties in evaluating the actual values of foundation design factors such as settlement. The acquired continuous records of Cone Penetration Test (CPT) can be used to determine the soil profile and characteristics those are applicable in the geotechnical design. In this paper, it has been attempted to present a new non-linear stress-strain approach to estimate the foundations settlement by using CPT data in the form of soil behavior classification charts. This new approach is based on Janbu method (1960s and also 1998). Instead of using fixed and constant values for stress exponent (j) and modulus number (m), continuous coefficient variations can be used. The proposed approach also can be used as a new method to predict pile group settlement. A data bank has been compiled containing twenty-two practical case histories to investigate the accuracy of the predictions made by the proposed and available common methods. The comparisons indicate that the proposed approach is relatively able to predict the settlement close to their real values. Therefore, it can be considered as an alternative method based on valuable CPT data and nonlinear stress-strain approach for foundations and pile groups settlement estimation.INTRODUCTIONComplexity in soil behaviour for settlement analysis is the result of non-linear and time dependent stressstrain behaviour of soils, their elasto-plastic performance under loading and unloading situation and also effects of stress history (Holtz et al., 2011; Fellenius, 2015). Hence, many relations and equations have been proposed to predict foundation settlement, where most of them are based on typical different parameters such as soil stiffness (E), foundation width (B), contact pressure (q) and pressure developing in depth (Janbu, 1967 also 1998; Briaud and Gibbens, 1999; Uzielli and Mayne, 2012).The Janbu approach for settlement estimation, proposed by Janbu in the early 1960s, combines the basic principles of linear and non-linear stress-strain behaviour of material. The method is applied to all types of soils. The relation between stress and strain is a function of two non-dimensional parameters which are unique for any soil: a stress exponent, “j”, and a modulus number, “m”. The Janbu relations are derived from the definition of tangent modulus by the following expression:"

Jan 1, 2017

By KeerthiRaaj Subrmanian, Muthukkumaran Kasinathan

"A railway embankment is under construction between Nagapattinam to Thiruthuraipoondi covering 36.5 km. The sub-soil strata comprises of soft clay extending up to 10 m below existing ground level, which is subjected to stability and settlement problems. A trial stretch covering about 5 kilometer was improved using Prefabricated Vertical Drains (PVD) with surcharge was recommended to accelerate the consolidation settlement. The geotechnical characteristics of the subsoil are examined through laboratory tests on representative soil samples. Recent improvement in the finite element analysis has facilitated modeling of PVD in finite element software for computing the settlement magnitude and time rate of consolidation. In this study the theoretically predicted settlement magnitude and time rate of consolidation from Terzaghi.s vertical consolidation, Barron's radial consolidation are compared with the analyzed FEM results for both the cases with and without PVD improved embankment. The comparative analysis between FEM and predicted data hold good for stresses and the associated deformations. The excess pore water pressure was significantly lower and their dissipation was faster in case of embankment with vertical drains. Thus PLAXIS 2D tool shows fairly convincing results in comparison to the theoretical solutions.1. INTRODUCTIONFrom the earlier times civilization has been developed in a fashion either at the banks of river or near to the shore region, because of the easier availability of food and water. This over centuries made them as huge cities, consequently population rise made the increased necessity of highway, railways, port and even more ground for construction. As a stake researchers are pushed to make a low bearing ground into a massive carrier of skyscrapers, embankment, bridges etc. These low bearing ground suffers from total and differential settlement, slope instability. Hence, numerous ground improvement techniques were followed to eradicate these concerns which include preloading, piling, stone column, vertical drains and geosynthetic reinforcement. Among them Prefabricated vertical drain (PVD) are often used to accelerate consolidation of soft subsoil and has been the main soil improvement method used in improving the soft marine clay deposit (Chu et al.(2004); Chai (2001) and Arulrajah et al.(2003)). Literature review of embankment over soft clay deposit reveals that combination of PVD with preloading is widely considered as an economical and less time consuming ground improvement technique."

Jan 1, 2015

By R. A. Fraser

Large diameter (1.0 to 2.5m) bored piles have been widely used to support buildings and elevated roadways in Hong Kong. Most of these piles are founded on a hard bearing stratum such as granitic or volcanic bedrock, in the newly reclaimed areas along the water-front, the bedrock stratum can be as deep as 70-80 metres below ground surface, and construction of bored piles to bedrock in this case is difficult and unjustified. Nevertheless, Building Ordinance Regulations in Hong Kong require piles to be founded on bedrock. To overcome this problem for elevated roadways, trial piles have been designed founded on dense, completely decomposed granite. A number of piles have been constructed and subsequently load-tested to allow the rate of mobilisation of skin friction to be measured. This paper outlines the design, construction and testing method, and comments on the test results from several trial piles. GEOLOCICAL CONDITIONS The geology of Hong Kong consists predominantly of acid volcanic rocks intruded by granite. The granite has been deeply weathered, and variations in sea level have produced a drowned coastline with sequences of alluvial, colluvial and marine deposits overlying the weathered bedrock. Reclamation has extended this coastline. Typical site conditions are described later in the paper.

Jan 1, 2010

By Adel Hanna

Earth pressure acting on piles driven in sand is playing a major role in estimating pile capacity. In literature, researchers entertained simplifying assumptions in estimating the earth pressure acting on the pile's shaft, ignoring the effects of pile installation and pile size. Empirical formulae were introduced based on laboratory or field test results, where major discrepancies can be found among these formulae. In this paper, the theory of cavity expansion and the finite element technique will be used to establish the effects of pile installation technique and pile's diameter on the earth pressure acting on the pile's shaft and accordingly on the values of the existing coefficient of passive earth pressure and overconsolidated ratio. It is of interest to note that pile driven technique and pile's diameter have significant increase on the earth pressure acting on the pile's shaft and accordingly on the overconsolidation ratio in case of loose or medium sands, while they may cause crushing and dilation in case of dense sand. Keywords: Single pile, Cavity expansion, Cohesionless soil, Driven piles, Numerical modelling, Finite element technique, Earth pressure.

Jan 1, 2003

By Mohab Sabry, Emre Biringen

"Over the past decades, there has been an increasing recognition of the strategic use of pile-supported rafts in design of heavily-loaded structures to reduce total and differential settlements. However, such a hybrid foundation construction method has not been widely utilized in many countries, including the U.S., due to code limitations. In current practice, the foundation design is based on either (i) the bearing capacity of the raft supported by the subgrade soils, or (ii) solely the pile capacity. This paper addresses the potential use of such hybrid piled-raft systems, where the structural load is shared by both by the piles and the subgrade soils directly beneath the raft, in foundation design of power plant structures. The study assessed some of the characteristics of piled-raft behavior by undertaking three-dimensional finite element analyses of two raft sizes, and various pile layout patterns, including the rafts with piles distributed evenly and only in the central area of the raft. The computer software PLAXIS 3D with the Mohr-Coulomb constitutive soil model was used to facilitate the modeling of such cases. The results presented in this paper indicate how strategically locating the piles could reduce the differential and total settlements.INTRODUCTIONUnder the high applied loads coming from the superstructure, the addition of piles is primarily required to improve the factor of safety against failure when a raft does not provide adequate bearing capacity. If the bearing capacity of the raft is sufficient to carry the total load with a reasonable safety margin, then the addition of piles is usually intended to reduce the settlements to an acceptable amount. In current practice, the design process for pile-supported raft foundations conservatively concentrates on providing solely the pile capacity to carry the total structural load without taking the contribution of the raft into account. This paper addresses the potential use of hybrid piled-rafts in controlling foundation settlement of power plant structures by considering the support of both the piles and the subgrade soils beneath the raft to carry the load."

Jan 1, 2017