Search Documents

By R. Filippone, Donald Leroux, Colin Hardie, G. Leichtle, Cesar Gomez, Jim A. Finch

"Bubble surface area flux (Sb) is the surface area of bubbles per unit time per unit cross-sectional area of flotation machine. The units are: (m2 bubble surface/s)/(m2 cell) or s -1. For bubbles of mean size db (m), s b = 6-Qg/A db where Qg is the gas rate (m3/s), and A the cell cross-section (m'). This parameter is now receiving wide attention as the possible key machine variable in flotation diagnosis and modelling. The concept is described and the potential use of sb is illustrated by work on flotation columns and mechanical cells. In column flotation of recycled paper, the dependence of ink recovery on s b was the same regardless of size of column or type of sparger. In mechanical cells, it has been established that the rate constant is related to Sb independent of impeller type.The use of s b is limited by the problem of measurement, primarily that of estimating db. A prototype probe designed to estimate db (and hence sb) based on conductivity measurements is described. Exploratory work with the probe in a mechanical cell suggests the promise of making estimation of s b routine.INTRODUCTIONFlotation is the result of interaction among variables associated with the feed particles, chemistry and the machine (flotation cell). Trying to isolate the effects of each aids in process diagnosis and is at the centre of attempts to model flotation. The machine variables that have been investigated include the air flow number, the power number and specific power (Harris, 1976). None have survived as the basis for predicting flotation response perhaps because they did not include directly the properties of the bubble swarm (or dispersion). Recently, Gorain (1 997) explored the relationship between the flotation rate constant and various ""gas dispersion"" parameters notably: superficial air rate (Jg = Qg/A, where Qg is the volumetric gas rate and A is cross-sectional area of cell), bubble size (db), gas holdup (Eg, i.e., the volumetric fraction of a cell occupied by gas) and bubble surface area flux (sb = 6.Jg/db). Of them all, Gorain et al. (1997) conclude that the latter, the surface area flux, correlated best with the flotation rate constant. This concept was adopted from column flotation where it was used to estimate, among other factors, the maximum amount of gas that could be injected (Finch and Dobby), 1990). Let's start by reviewing the concept. Following that some examples of where the concept has been applied will be described to illustrate the current interest and finally we will consider how to measure the surface area flux."

Jan 1, 1999

By James G. Lyons

All machines vibrate and make noise. An increase signals impending trouble. Vibration and noise analysis allows the condition of the machine to be determined without costly interruption in service for disassembly and physical inspection.

Jan 1, 1977

By Larry J. Hulbert, Louis J. Cabri, John L. Campbell, Gilles Laflamme, Chris G. Ryan, Soey H. Sie, Rolando Lastra

"Abstract- The mineralogy of samples from the Wellgreen Cu-Ni-Pt-Pd deposit, Yukon Territory, is complex and the metals of interest are contained within fme-grained minerais which vary in size and mineral associations from sample to sample.The major Ni carriers are pentlandite and violarite; the major Cu carrier is chalcopyrite. About 700Jo of the major Ni carriers and 78% of the major Cu qmier will be liberated at a grind of 80% -'}f,.7 J.Uil (-500 mesh) for typical low-grade gabbro (West zone, sample No. 1). For typical ""clinopyroxenite"" (West zone, sample No. 2) and typical ""clinopyroxene-rich peridotite"" (East zone, sample No. 3) the liberation would be 71""lo and 65% for Ni, 74% and 60% for Cu, respectively. Fine grinding, however, cannot liberate the Ni contained in silicates and pyrrhotite, estimated to total24.5% for typicallow-grade gabbro (West zone, sample No. 1), 15% for typical ""clinopyroxenite"" (West zone, sample No. 2), and 12% for typical ""clinopyroxene-rich peridotite"" (East zone, sample No. 3).The principal Pt carrier (sperrylite) varies considerably in grain-size between samples and fme grinding, required to liberate the major Ni and Cu carriers, may be counterproductive in samples where sperrylite is relatively coarse-grained, as sorne would then be unrecovered (e.g. sample No. 1). In addition, sperrylite in samples No. 2 and No. 3 is closely associated with magnetite.Palladium occurs in diverse ways. It occurs in the form of several Pd minerais (e.g. sudburyite, testibiopalladite, merenskyite), as a replacement for Ni in several tellurides, antimonides and tel­ lurantimonides (e.g. melonite), or as very low concentrations in pentlandite (up to 34 ppm), chal­ copyrite (up to 9 ppm), and pyrrhotite (up to 5.6 ppm). Palladium minerais and Pd-bearing minerals are strongly associated with chalcopyrite in sample No. 1 and will thus report to a Cu concentrate. However, 22% of the total Pd is in solid solution in pentlandite in this sample and will thus report to the Ni concentrate. In samples No. 2 and No. 3, less Pd occurs in solid solution in pentlandite, and the PGM are distributed mainly among pentlandite, chalcopyrite, and magnetite in sample No. 2, and among pentlandite, pyrrhotite, chalcopyrite, and magnetite in sample No. 3. Therefore, the feasibility of magnetic concentration should be investigated for samples like No. 2 and No. 3, in order to improve Pt and Pd recoveries.Rhodium was found to occur as rare hollingworthite, in sparse cobaltite (up to 2.7%) and, as low concentrations in chalcopyrite (to 10 ppm) and pentlandite (to 12 ppm) by proton microprobe. Iridium occurs in hollingworthite (up to 7.8%) and very rarely as the native metal or in an undefmed Re-Ir-Os-Ru alloy. Ruthenium was determined by proton microprobe analyses to occur in pentlandite (up to 13 ppm) and chalcopyrite (up to 10 ppm), in addition to rare laurite and Re alloy."

Jan 1, 1993

By Michel Jébrak, Claude Bellehumeur

Abstract - Regional and orientation geochemical stream sediment surveys were carried out by the Quebec Department of Energy and Resources in southwestern Quebec, over a part of the Mont­ Laurier Terrane of the Grenville Province. The area contains some small stratiform zinc deposits. The response of Zn mineralization to geochemical surveys is weak; the known mineralization is not defined by anomalous samples and consistent patterns. This study uses a technique that increases the geochemical signature of Zn mineralization in filtering out geochemical background components related to lithologies and surficial conditions. The background variations were modelled using principal component analysis, and the filtering technique consists of the partial reconstruction of the data matrix from results of principal component analysis . The filtering procedure considerably enhances the Zn anomalies located in the catchment basins of Zn deposits, and defines some new anomalies in proximity to the marbles of the Mont-Laurier Terrane, the principal metallotect of Zn mineralization.

Jan 1, 1993

By J. E. Danoczi

Shore Gold Inc. (Shore) is presently designing a diamond processing plant for the Star and the Orion South kimberlite deposits in the Fort à la Corne (FalC) area in central Saskatchewan. The first step in the plant is diamond liberation and occurs in the comminution section. Diamond liberation is the process of breaking up the kimberlite rock, as gently as possible so as not to damage the diamonds. Autogenous grinding mills (AG mills) use a combination of impact crushing, abrasion and attrition to break up the kimberlite. The forces that occur during the actions of abrasion and attrition cause the kimberlites to break up preferentially along lines of weaknesses which offers a ?diamond friendly? method of comminution. Hard competent kimberlite is commonly found in the diatreme zone as well as the root zone of the volcanic pipe and is the source of kimberlite for most of the Southern African diamond mines. Softer kimberlite is typically found in and around the crater area of a volcanic pipe and it is this kimberlite that makes up the majority of kimberlite for both the Star and Orion South deposits. These softer kimberlites can be readily broken up using abrasion and attrition imparted by AG mills. In order for Shore to benefit from the softer kimberlite found in the Star - Orion South diamond project, two large (10.97 m diameter x 7.10 m long) AG mills were designed for the comminution section based on extensive test work and simulations by Metso Minerals (Metso).

Jan 1, 2012

By M. Mononen, J. Huuskonen, M. Vauhkonen, J. Kourunen, A. Lehikoinen

"A new approach to measure process conditions in flotation cells is presented. Real scale flotation cells in a Zinc circuit are imaged using Outotec LevelSense sensors based on electrical resistance tomography. The latest results from long period plant tests show that the sensors together with FrothControl analysis give new information that correlates well with other process parameters. The sensors can compensate for electrical contact contamination using an automatic calibration technique and they are basically maintenance free. The results indicate that using the LevelSense sensors and FrothControl solution, the process control and optimization can be done automatically, stabilizing and improving the metallurgical performance of the flotation process.INTRODUCTIONThe froth flotation process is widely used in mineral industry for the separation of minerals from low-grade ore slurry. Different property parameters of froth and slurry could be measured to monitor and control the flotation process: air bubble size distribution, flow dynamics, thickness of the froth bed, amount of solids in the froth, etc. Some techniques already exist that can be utilized in studying these important parameters on-line. Examples of the techniques are the high-speed video imaging, simple conductivity probes, ultrasound techniques, floats and pressure transducers (Maldonado et al., 2008). These techniques, however, often suffer from some limitations. For example, the video imaging only gives information from the surface of the froth, simple conductivity probes suffer from contamination and the floats may get stuck and therefore do not give reliable signal for process control and optimization."

Jan 1, 2013

By John McEwen, Ian R. Jonasson, David H. Watkinson

"Mine Gallen is a zinc-rich pyritic volcanogenic massive sulphide deposit that occurs in a fault-bounded block of intermediate volcanic rocks. The block is completely surrounded at the present erosion level by the eastern part of the Lac Dufault granodiorite. The volcanic succession includes a massive feldspar porphyry that is probably a subvolcanic intrusion, an andesitic flow unit and lapilli tuffs. The latter are variably sericitized and pyritic, especially in the vicinity of the massive sulphide into which they grade.The ore body is predominantly pyritewith local sphalerite contents as high as 20%; minor chalcopyrite and trace galena are disseminated, but are found mainly along late cleavage. Most ore is a breccia of massive to banded pyrite-sphalerite, veined by massive and complexly banded sulphides. These structures formed by repeated blocky jointing, cracking, sealing, healing and annealing as hydrothermal fluid repeatedly passed through a developing sulphide mound. The deposit is interpreted to have grown on the seafloor in a manner similar to active mounds in the Galapagos rift.RESUME La Mine Gallen exploite un gisement de sulfures massifs volcan géniques comprenant essentiellement de la pyrite riche en zinc. Ce gisement se trouve a /'intérieur d’un bloc de roches volcaniques de caractère dacitique a andésitique, limite par failles et entoure de tout cote par la granodiorite du Lac Dufault. La séquence volcanique comprend des coulées andésitiques et des tufs à lapilli ainsi qu'un porphyre feldspathique massif sub-volcanique. Les tufs sont sericitises et pyritises, tout particulièrement au voisinage des sulfures massifs."

Jan 1, 1990

By W. Tse, D. Wong

Dense medium separation (DMS) is one of several preconcentration methods used for early waste rejection from run of mine ores at relatively coarse particle sizes prior to additional milling and beneficiation. DMS has been used extensively in the coal, diamond and iron ore industries but lab scale and pilot test work has demonstrated successful separation and upgrading of other minerals such as lead, zinc, copper and lithium based ores using DMS. This paper reviews historical dense media systems, results from the pilot scale Condor DMS system as well as associated laboratory heavy liquid separation (HLS) test work.

Jan 1, 2014

By J. M. Whiting

"North America has entered a period when greatly increased attention must be given to energy .supply and demand by government, industry and individuals. Such increasing concern about energy will be a long-term phenomenon, accompanied by continuing examination of future resource development and utilization. Those engaged in or associated with mining, a major energy consumer, are likely to experience a variety of problems which are associated with the end of an era of low-cost, virtually unlimited energy supply. Their efforts, furthermore, may be subjected to escalating public and government scrutiny, involvement and control. However, ever-growing recognition of the real and urgent necessity to systematically develop new energy supplies within Canada and the United States will provide unusual challenges and opportunities for those companies and individuals with mining expertise. The vast deposits of coal, tar sands and oil shale provide a relative certainty of supply which only stands to gain in attractive ness with time. In order to benefit from this aspect of certain supply, nevertheless, synthetic fuels will have to be produced at a tolerable cost. This will always require excellent process design and engineering. As synfuels development expands to any significant production level, however, and Jess than ideal reserves are scheduled, the usual geologic-productivity complexities encountered in making ore out of low-value rock will tend to become of prime concern. It is for this reason that the services of experienced mining personnel will be in growing demand in energy production."

Jan 1, 1973

By D. T. White

"Metallurgical extraction processes often call for the heating of aqueous slurries. Indirect heat exchangers are generally not feasible for service with high yield stress slurries because of low heat transfer rates. It is more appropriate to heat the slurry by direct contact, typically with steam as the heating medium. Although having a long and successful history, direct-contact heat transfer to aqueous slurries has been used without the support of pilot plant research. This paper provides results of the needed research, the work being done at a scale large enough to enable direct scale up to commercial operations. A pilot plant heater was constructed and tested to develop an understanding of the slurry heating process and to ensure that commercial scale heaters were appropriately sized.INTRODUCTIONPressure Leaching OperationsPressure leaching operations are often used to oxidise sulphide gold ores, or for extraction of nickel and cobalt from laterite ores with sulphuric acid. Where there is sufficient sulphur available, the exothermic pressure oxidation reactions can be self sustaining at temperatures as high as 225 ºC, without having to preheat the feed slurry. At lower sulphur levels, slurry preheating is required. This is typically achieved by utilising the flash steam released from the slurry letdown stages and contacting this directly with cold incoming slurry ahead of the autoclave. The vessels where this slurry-steam contact is made are known as heaters or condensers, with the number of pre-heat stages varying, depending on how much heat is evolved in the oxidation reaction (Mason, 1990).In nickel laterite pressure acid leaching processes, which operate between 245 and 270 ºC, the only significant exothermic reactions are those associated with dilution of sulphuric acid in the leach. As a consequence, slurry preheating with flash steam is always used commercially. In practice the number of flash steam preheating stages required varies from 1 to 3, driven by a number of factors, including other uses for flash steam and the upper temperature limit at which preheated slurry can be pumped. A diagram of a typical pressure acid leach train is shown in Figure 1.For pressure acid leaching operations and at low sulphur levels in pressure oxidation, boiler generated direct steam addition to the autoclave is required to sustain the reaction temperature. For this reason it is imperative that the flash steam – slurry heat transfer is efficient and the slurry temperature approaches that of the flash steam closely."

Jan 1, 2012

By A. K. Chetin, W. W. Fitkin

"The reservoirs of Mississippian Mi-dale beds and Frobisher beds found in the Weyburn field lie at the north-western termination of a broad productive belt extending 120 miles along the northeastern rim of the Williston basin. These carbonates, and inter-bedded evaporites, originated during cycles of marine transgression and regression, and were deposited as rock types characteristic of shoal, lagoon, and basinward shelf environments. The Frobisher-Alida Beds, which form a secondary reservoir to the main Midale Beds of producing zone are composed of oolit1c, fragmental-bioclastic, vugular limestone capped by an impervious dolomitic mudstone. Production is controlled by localized structural features resulting from de-positional build-up. Excellent reservoir conditions are accompanied by an active water drive. The Frobisher Evaporite, consisting of massive primary anhydrite with dolomitic veinlets, forms the floor seal for the Midale beds oil accumulation. A significant facies transition into an oolitic, bioclastic, vugular limestone characterizes this unit. Beyond the depositional margin of the evaporitic facies, marked increases in porosity and permeability of the en-tire reservoir are noted. Carbonate units overlying the areal extent of the Frobisher Evaporite exhibit a greater degree of metasomatism, dolomitization, and more abundant secondary anhydrite.Porous carbonates comprising the producing zone of the Midale beds are divided into an oolitic, fragmental bioclastic, vugular limestone, and an overlying granular marly lime-stone unit, capped, by the Midale Evaporite. Oil is accumulated in a stratigraphic trap bounded above and be-low by primary anhydrite and truncated by the post-Mississippian erosional surface. Mississippian strata dip basinward from this erosional surface in a broad homocline exhibiting only minor irregularities. Rapid lateral and vertical porosity and permeability variations are common. Localized, separated, porous lenticles contain interstitial water in areas where the Midale beds are underlain by the Frobisher Evaporite. The major portion of the field, however, is capable of water-free production. Bottom and edge waters are found in certain portions of the field. Productive limits are tentatively defined around most of the present field perimeter. A large area along foe southern edge of the field remains open to future development. Probable ultimate remaining recoverable crude oil reserves, as of September 30th, 1958, were estimated by Mc-Daniel Consultants Ltd. to be in excess of 330 million barrels."

Jan 1, 1959

By Stanley G. Butcher

"Introduction Many operators in western Canada, with a background in the minerals industry, talk of ""coal beneficiation"", whereas the coal industry generally uses the term ""coal preparation"" . The sophisticated cleaning circuits and thermal drying units found in western Canada makes the term beneficiation particularly appropriate. This chapter uses standard coal preparation terminology(l,2J and assumes general knowledge of coal preparation unit processes and equipment(3,4,5). The geologic setting and mining methods of western Canada, described elsewhere in this volume, present for preparation run-of-mine coals which have particular problems. As a result the cost of preparation is a higher proportion of the total minesite production costs than in other coal fields . Preparation requirements are determined by the types of coals being produced and the markets in which they are sold. Western Canadian coals have a low sulphur content and do not require cleaning on this account. Prepared coal from western Canada has to be shipped vast distances -to the Pacific Rim countries and Ontario in particular -and the savings in transport costs justify the high costs of preparation. Factors which dictate selection and operation of the preparation processes are: i) Market specifications and coal rank. ii) Size distribution of particles and particularly the liability of coal and refuse particles to degrade during handling and processing. iii) Quantity and characteristics of the associated refuse. iv) Washability characteristics (the distribution of particles by specific gravity within each size fraction). v) Surface characteristics of the fines. vi) Variability of the raw coal. Where the product (coal or discard) has a high fines content special consideration must be given to dewatering, the removal of surface moisture, to give acceptable handle ability characteristics. In the severe winter climate of the western foothills and mountains thermal drying is necessary to prevent freezing of washed coal in stockpiles and railcars."

Jan 1, 1985

By P. Kawulka

An integrated pilot plant for the development of the S-C Copper Process was constructed at Fort Saskatchewan in 1975 and operated in 1976. The pilot plant was designed to treat 9 tonnes per day of a pyritic copper concentrate. A demonstration run conducted during the last quarter of 1976 averaged 90% on-stream time, and confirmed that the process is operable as a stable and integrated unit. The paper describes the parameters and equipment developed for thermal activation of chalcopyrite copper concentrates to make them amenable for the dissolution of iron and zinc, and their subsequent separation and recovery. The resulting high-grade copper sulphide was leached with return electrolyte and oxygen to extract 98.5% of the copper into solution. The copper was electrowon at 650 amps per square metre from purified solution, to produce cathodes analyzing 0.1 ppm Se, 0.1 ppm Bi, 4 ppm Pb and 10 ppm S. The electrical conductivity was >101% lACS and the spring elongation value [ ]350 mm. Elemental sulphur and gangue are removed from leach residues to make a concentrate containing over 95% of the silver and gold and most of the unleached copper. Conventional construction materials such as stainless steel, titanium, Hastelloy, acid brick, rubber and plastics performed well. The containment inherent in hydrometallurgy provided high standards of hygiene and safety.

Jan 1, 1978

By P. Mundell, R. Torbin

"There are many physical and operational obstacles in pipelines that make the passage of inspection robots impossible including:•,Small radius bends•,Low operating pressure•,Plug valves•,Large changes in pipe size•,No permanent access to the pipeline.The inspection of unpiggable pipelines requires the marriage of a highly agile robotic platform with NDE sensor technology operating as an integrated system. Foster-Miller and GE/PII are developing a robot that is essentially a battery powered, train-like platform. Both front and rear tractors propel the train in either the downstream or upstream direction. Like a train, the platform includes additional ""cars"" to carry the required payloads. The cars are used for various purposes including the NDE sensor module(s), the power supply, and data acquisition/storage components. The robot is designed with a slender aspect ratio and the ability to change shape as required by the physical obstacle presenting itself. The MFL sensor module must also morph itself through the physical obstacles, and thus, will require some level of segmentation. The segmented MFL magnetizers and transformable sensor module represent a major advance in the science of sensor technology and pipeline inspection."

Jan 1, 2005

By L. H. Van Loon

INTRODUCTION THE property of Madsen Red Lake Gold Mines, Limited lies between Russet and Faulkenham lakes in Baird and Heyson townships, district of Patricia, Ontario. It is about six miles south west of the town of Red Lake, with which it is connected by an all-weather road. All orebodies found to date at the property are silicified lenticular bodies which lie within tuff beds. The ore bas a specific gravity of 2.95. It consists of mica and chlorite schist, silicified and containing a considerable amount of disseminated carbonate, and mineralized with pyrite, pyrrhotite, magnetite, arsenopyrite, and chalcopyrite. Of these, pyrite, in coarse to fine disseminated grains, is by far the most abundant. Pyrrhotite occurs in ?the gangue material as medium to fine disseminated grains. A very small amount of arsenopyrite, in small crystals, is associated with the pyrite, and small grains of chalcopyrite occur in both gangue and pyrite. Although some of the gold present in the ore is quite coarse, a good deal of it is extremely fine.

Jan 1, 1951

By R. F. Favreau, L. C. Lang

"In modern blasting technology blasts are designed and analysed on an energy-mass-time relationship. The energy of the explosive is derived by computer analysis and the work potential of the available energy is expressed in numerical values. The mass involved in the blast is determined by the geometry of the blast and by the rock density. Time is also a relevant parameter, because time is required to complete the three basic stages of the breakage process.For successful application of the blasting parameters the basic mechanism of the breakage process must be understood.The physical-mechanical properties of the rock, local structural geology and the thermodynamic properties of the explosives can be brought together to create a computer model of a blast with which it is possible to predict separately the results of each parameter and to express the predicted degree of change in any parameter by actual numbers.A long-range project has started to create a ""bank"" of rock properties for as many Canadian and foreign mines as possible. A computer model has been successfully applied to predicting the effect of varying the ratio of spacing to burden at constant rock volume and significantly improved results are achieved, as the S/B ratio is increased up to about 2 to 2.5.High-speed photography has been applied to determine the time that has elapsed between zero time and the beginning of movement of the mass. The results assist in determining minimum and optimum delay time required for multiple-row blasting.The approach as described in the paper is now well proven and is clearly superior to previous methods based on powder factors and human assessment."

Jan 1, 1972

By H P. Tardif

This paper briefly describes some of the phenomena encountered when materials are submitted to extremely high pressures, such as those produced by the detonation of an explosive charge placed in contact with the material. It was found that extensive changes take place in the? microstructure of iron and steel. Diffusion-controlled processes, such as the transformation of lamellar pearlite, the recrystallization and grain growth of ferrite, and the homogenization of the pearlite-ferrite structure, can take place within micro-or milliseconds. Mechanical twins can propagate without deviation from ferrite to pearlite, thus indicating a proeutectoid ferrite-pearlite-ferrite orientation relationship. The propagation and interaction of intense stress waves in materials was demonstrated with the use of Armco iron. Finally, a comparison is made of the damage produced in metals by the formation of craters made by explosive shock and by hypervelocity impact. D DRING the last few years, exceptional development has taken place in the field of explosive metallurgy, i.e., the

Jan 1, 1964

By J. Chlopas, D. J. Barratt, M. V. Sharp

"This paper describes the modifications made to the Fox Mine copper concentrate bin in order to obtain a continuous flow condition. The design of these modifications is based on test results obtained on Fox Mine concentrate using the flow factor testing machine in the research facilities of Cominco at Trail, B.C.The original design consisted of a cylindrical steel bin on a concrete slab with two slot-discharge openings. Based on predictions of the maximum mass flow hopper angle for conical and wedge shaped hoppers for the concentrate on various potential bin lining materials, Ultra-High Molecular Weight (UHMW) Polymer was selected as a liner.Using the recommended angles for conical and wedge shaped hoppers, the profile of the bin base was changed to suit the existing slot openings.The initial method of fastening the liner resulted in failure of the connections. Subsequent modification to the zinc concentrate bin fastener system proved satisfactory and it has now been in operation for over one year without any separation of the lining material.Utilization of flow testing procedures on concentrate samples has demonstrated that proper design of storage bins or hoppers to achieve continuous flow can be incorporated into the design of new plants."

Jan 1, 1978

By J. E. Gill

"The name 'Canadian Shield' is used for a vast area; largely in northeastern; Canada; underlain by Precambrian rocks. The part in Canada has an area; of about 1; 790; 000 square miles. Extensions in Greenland; Labrador; Newfoundland; and the United States bring the total area to around 2; 800; 000; square miles. The boundaries of the Canadian part are shown in Fig. 1.; At its margins; the Precambrian rocks can be seen at many places to; extend beneath a cover of flat-lying Palxozoic or later sediments. Information; from borings in the Plains and natural exposures in mountain-built belts; show that similar rocks form a large part of the continental platform. The; Shield; therefore; is a large exposure of what may be regarded as the foundation; of the continent."

Jan 1, 1954

By L. Frost

Physical Conditions Great Britain The physical conditions in the mines investigated in Great Britain are similar to those found in the mines of the Dominion Steel and Coal Corporation, with the important difference that many of the coal seams visited were interspersed by a large number of heavy faults, making the development of a continuous face operation difficult, and in many cases the life of a unit development was exceptionally short, adding to unit cost; but in spite of these difficulties, a great deal has been accomplished in the application of mechanical loading units in a number of the mines in the areas visited. The coal-bearing measures, as in Nova Scotia, consist of shales and sandstones, and in some sections mussel bands overlie the coal seams making roof conditions difficult'. In several mines, the main roof consisted of weak shale bind, being held by a coal roof of varying thickness. This shale bind had a tendency to flow when the coal roof was broken. The floor, in some cases where cutter loaders were operated successfully, consisted of weak, flaky shales with very little resistance and a tendency to disintegrate into powder when broken. The depth of cover under which these mines were operating varied from 250 feet to 2,340 feet, with an average of 1,700 feet. The coal seams varied in height from 3 feet to 8 feet 6 inches, and the gradients from level to 33 per cent. The seams vary in hardness, but all-with the exception of one seam, the 'Morrison Busty'- presented a cutting problem similar to that found in Nova Scotia. The structure and cleavage of the coal was well defined and uniform. Some of the seams visited were gassy, ?but the temperature of the workings generally was not in excess of 70°F.

Jan 1, 1948