Search Documents

By H Jones

Closure cost estimates may be generated at any stage of a mining operationÆs life; commencing with the initial prefeasibility studies and continuing through to the final decommissioning cost estimates. However, not all mine closure cost estimates are necessarily the same. Cost estimates will vary depending on the purpose for which they are prepared, the organisations requiring or undertaking the estimate and the stage of the mining operation. Different organisations can legitimately arrive at disparate cost estimates for closing the same mine because the organisations have different reasons for requiring the estimates. Another, equally valid, reason for potentially wide variations in cost estimates by different organisations on the same mine site is the different definitions of æclosure costsÆ used by different estimators. This paper considers the different approaches by different organisations including operating companies, government authorities and financial organisations and uses a hypothetical example based on practical experience to illustrate some of these differences in estimation methods.The paper suggest that a more consistent approach to closure cost estimating in the Australian mining industry would assist mining companies, governments, the accounting industry and the broader community to better understand this complex component of mine planning. One possible approach to closure cost estimating is briefly outlined.CITATION:Jones, H, 2012. Closure cost estimation - All things to all men?, in Proceedings International Mine Management 2012, pp 115-124 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 20, 2012

By R Domotor

Brisbane’s Airport Link is Australia’s largest road infrastructure project, worth a total value of A$4.8 billion. The project is using surface and underground blasting to excavate hard volcanic rock, Brisbane Tuff. This paper tells the story of the most challenging and difficult blast of the whole project: the removal of a remnant pillar of rock (approximately 2250 m3) next to a major arterial road and within 100 m of existing infrastructure including a number of heritage listed buildings, residences and privately owned sensitive receivers. The pillar consisted of a hard rock wall (Brisbane Tuff) between 2 m and 6 m thick, 15 m high and 35 m wide; with in situ precast concrete piles embedded within 1 m of the boundary of the pillar. Orica Australia Pty Limited was contracted by Thiess John Holland, to perform the work in this area, including design, modelling, drilling and loading of the explosives, as well as blast clearance and shotfiring. Access to the area was limited so all explosives and equipment, including the 20 t drill rig, had to be lifted in and out by crane. Due to the nature of the blast, with infrastructure 5 m directly in front of the 15 m high face, there was only ever going to be one chance to get this blast right. This was an extremely complex blast which required the use of a number of different types of packaged explosives, as well as special timing techniques only made possible by using electronic initiating systems. This type of blast is high risk, and is more typical of a building demolition in the urban environment. The blast was fired on the 25 September 2010, and was highly successful. The environmental results for vibration and overpressure were well under the imposed limits, and the embedded concrete piles remained undamaged.

Nov 8, 2011

By A D. Caccioppoli

Grade control systems within Rio Tinto Iron Ore have proven to be robust, when mining full benches. The Hope Downs 1 operation hosting two Marra Mamba Iron Formation deposits (North and South Deposits) presents a new challenge, where increased mining selectivity due to moderately plunging N-verging folds has made flitch mining necessary in the South Deposit. Poor flitch blasthole sample duplicate results in South Deposit over a 12 month period, compared to North Deposit, have highlighted concerns with grade predictions. In contrast a new grade control methodology (grade splitting) was proposed to alleviate blasthole sampling bias, utilising geological mapping and mineralogical logging, currently practised throughout Rio Tinto Iron Ore Pilbara operations, to estimate theoretical grades for each flitch from a single blast cone assay. To assess this method, reverse circulation holes (RC) were twinned to blastholes establishing an ‘actual’ grade. These blastholes were assayed using current flitch sampling techniques where: flitch positions were estimated, flitch positions were marked with paint, and a full cone sample was taken for ‘grade splitting’. Using these data sets multiple grade predictions were produced, then analysed using Half Absolute Relative Difference (HARD) statistical analysis. In addition to testing these grade control methodologies two other findings were ascertained: an inherent bias in blasthole assays exists particularly in the top flitch, where an average absolute difference of 0.6 per cent in SiO2 and 0.42 per cent Al2O3 was measured; and assays derived where kaolin rich soft shales are intersected were less representative. This is likely to be due to these materials not being properly represented in blast cones. Grade splitting accurately estimated block chemistry, except for a slight under-prediction in Al2O3 and P compared to current grade control methodologies. This method is a viable alternative where grade distribution is stratigraphically controlled.

Aug 22, 2011

By J-P Franzidis, E V. Manlap

Froth transportation characteristics have a significant impact on the flotation recovery especially in large flotation cells. The probability of an attached particle being recovered into the concentrate depends strongly on the location where it enters the froth phase. A mathematical model for froth transportation in industrial flotation cells was proposed (Zheng et al, 2004). The model has been tested on the experimental data obtained from testwork conducted at the Western Metals Hellyer lead/zinc concentrator. The results show that the model fits the experimental data well, especially when the froth is well developed (ie for a deep froth). The model fitting can be significantly improved by incorporating an air dispersion factor. However, the models encounter some limitation, ie inconsistent prediction at different froth heights, due to change in froth viscosity which cannot be modelled at the present time.

Jan 1, 2005

By A F. D C Varajpo, R C. Weba, C Volkmer-Ribeiro, C A. C Varajpo, N S. Gomes

This study relates to the spongillite deposits from the region of Jopo Pinheiro, in the north-west of the State of Minas Gerais, south-eastern Brazil. The deposits occur in shallow ponds (with a maximum depth of 3.5 m) on a karstic planation surface developed on rocks of the Spo Francisco Neoproterozoic Supergroup. Cenozoic detritic covers are associated with this surface. The field study of spongillite deposits from the Preguita and Avipo deposits revealed sedimentological and pedological similarities between the different deposits. They have a lenticular shape and contain different layers of sedimentary spicules intercalated with layers of quartz sand and clay minerals. Representative samples from the different layers investigated by X-ray diffraction, differential and gravimetric thermal analysis and infrared spectroscopy showed a range from three to 80 per cent of amorphous silica (opal) corresponding mostly to the sponge spicules in the sediments. Optical microscopic investigation determined that the spicules predominantly belong to the sponge Metania spinata. This species is represented by smooth megascleres (alpha type), prickly megascleres (beta type) measuring 240 to 450 mm in length, as well as the spiny microscleres; whereby the smooth megascleres are larger and thinner. The morphological variation of the spicules as well as the presence of more fragmented spicules towards the base of the deposits, portray a variation in texture and in the state of their preservation along the profile, suggesting environmental variations at the time of their formation and deposition.

Jan 1, 2008

Green policies have gained momentum since the 1972 Stockholm, Environment Conference. The environmental movement has influenced political initiatives both in New Zealand and abroad. Governments and international institutions have addressed local, regional and global environmental issues with varying degrees of success. New Zealand so far has not supported the United Nations' call for sustainable development in a consistent manner. New institutions and new rules for resource management mean there are opportunities to look after the land in different and more ecologically sensitive ways than has happened in the past. The increasing influence of regional councils in resource management planning will have important implications for mining and mineral exploration. These trends are discussed and possible future events outlined. Green policies have gained momentum since the 1972 Stockholm Environment Conference. Environmental issues are now global and the twentieth year Environment Conference planned for 1992 is likely to see new commitments made by world leaders and their national governments. Green politics may be the popular trend of the moment but green principles of managing the earth's resources are here to stay. There are many businessmen, many technologists, and many politicians who have hoped that the environmental movement was a passing fad and would fade into oblivion. The evidence is otherwise. Far from passing into oblivion, the environmental movement is growing rapidly. Each year brings further scientific data that indicates mankind is on a self destructive course unless we learn how to better manage the earth's natural resources. This information has contributed to a growing population of environmentally aware people. In the last 20 years there have been messages of concern about a population increase out of control and the energy crisis which focused on dwindling oil stocks. The issues are all interrelated including the present global issues of climate change and thinning ozone layers. The attention being given the messages by the United Nations and member states requires similar attention by industry. The problems have been identified; the challenge is to determine what should be done about them. Every challenge brings new opportunities and the future need not be doom and destruction. Mining is seen by some of the environmental action groups as unnecessarily destructive of the environment, but I do not see mining ceasing in the next few decades. Rather, the rules will be clearer with some areas excluded from mining, the methods of extraction will improve, the technology of processing will become more sophisticated and restoration of mining sites will be not only normal practice worldwide, but the end result may leave no hazards, may enhance the landscape and may result in acceptance of the industry by the general public. For that to happen, commitment and cooperation is required between the industry, the government, and society. As an Officer of Parliament my role is to review the system of agencies and processes established by Government for allocating, using and preserving natural resources and to report whether the system is maintaining and improving the quality of the environment. I also have a responsibility to see that the environmental planning and management carried out by public authorities is effective. That Ineans I have a keen interest in how the mining industry is administered by New Zealand public authorities, including Ministers of the Crown and district and regional councils. Today I intend to review the approach to resource management being taken by international agencies and by the New Zealand Government, and to comment on how environmental impact assessment for mineral exploration, as well as mining, may be administered in the future.

Jan 1, 1990

By T Isaksson, J Anderson

The procurement process for underground construction contracts, in particular those contacts involving tunnel boring machines (TBMs), is subject to many complex and inter-related variables, including national and local politics, public policy, community involvement and media attention û as well as strict environmental and legal requirements. Other restrictions include the time available to adequately investigate geotechnical conditions and viable technical options to determine the best construction methodologies û including selection of tunnel boring machine characteristics and, those construction means and methods suitable for the specific geotechnical and environmental conditions. The latter are, most often, quite imperfectly understood. æGetting it rightÆ implies that an optimal configuration û of machine type, characteristics and associated methodologies û can be found and successfully implemented for a particular project. æFrom the beginningÆ implies that the lack of time issue can be successfully resolved. Within an international context this paper highlights a number of issues of concern which relate to tunnel procurement systems and the ways in which certain key processes are managed during planning, design and construction. The authors argue that there is considerable room for improvement in the way tunnelling projects are undertaken and an approach is discussed which has the potential for substantial gains in cost and schedule and reduction of risk. Savings, however, may only be fully realised if the new methods can be fully implemented by all parties involved. This, we believe, will require the rejection of ætraditionalÆ forms of management and procurement with associated changes in the roles and responsibilities of owner, engineer and contractor. Additionally, risk identification, assessment and mitigation are essential cost and schedule control process which have, to this point, been underutilised by the underground construction industry.

Jan 1, 1999

By M Kim, J Park, I-K Suh, E Kim, J Lee

One of the key technologies in developing hydrogen-enriched ironmaking operations is the control of the carburisation, melting, and dripping behaviour of the iron ore burden materials. When a hot compacted iron (HCI) is charged in the blast furnace or the FINEX Melter-Gasifier, iron oxide reduction, the reduced iron’s carburisation, and the melting of iron and slag occur successively. This study investigated the reduction, carburisation, melting and dripping behaviour of HCI under a COH2 gas mixture using the high-temperature X-ray radiographic technique. Under 100 per cent CO gas atmosphere, the dripping temperature was 1410°C. When 5 per cent H2 was introduced, the dripping temperature slightly decreased to 1400°C. Furthermore, the dripping temperature gradually increased as the H2 gas composition increased. As 30 per cent H2 was introduced, the dripping temperature reached 1414°C. The carbon concentration in the drained metal samples gradually increased with increasing H2 composition. It is considered that H2 decreased FeO content in the slag, yielding the increased melting temperature and viscosity of the slag. On the other hand, H2 accelerated the carburisation of the reduced iron by CO gas, enabling the homogenisation of the oxide materials to form a liquid phase. Therefore, it is considered that introducing H2 in the reactor is helpful to increase productivity and energy efficiency by accelerating the liquid phase’s formation.

Aug 21, 2024

By G S. Anderson, N W. McDonald

"The IsaMill™ was originally developed to address liberation issues at Mount Isa Mines (now Glencore) operations, McArthur River and Mount Isa in the early 1990s. Following on from the industrial success at those operations, the IsaMill™ was commercialised. In the year 2000, Kalgoorlie Consolidated Gold Mines (KCGM) became the first external user of the technology with a 1.1 MW M3000 IsaMill™ installed to supplement the roaster capacity at its Gidji Processing Plant. The IsaMill™ was used to ultra-fine grind about 10 t/h of pyrite flotation concentrate to 10–12 µm prior to gold cyanide leaching. Based on the success of the Gidji installation, another was installed at the processing plant at KCGM’s Fimiston operation in 2002 in a similar duty.In 2014, a 3 MW M10 000 IsaMill™ was selected to replace the roasters at Gidji as part of the A$98 M emissions reduction project. The mill was commissioned in April 2015 at the design 30 t/h, allowing the immediate shutdown of the two roasters. Replacement of roasting with ultra-fine grinding completely eliminated air emissions at Gidji while maintaining overall plant production rates.This paper details the history of the IsaMill™ at KCGM from the original M3000 to the latest M10 000. It covers the basis of the process selection, circuit design, operating and maintenance data.Citation:Anderson, G S and McDonald, N W, 2016. IsaMill™ at Kalgoorlie Consolidated Gold Mines - from the M3000 to the M10 000 and Replacement of the Roasters at Gidji Processing Plant, in Proceedings 13th AusIMM Mill Operators’ Conference 2016, pp 29–38 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Oct 10, 2016

By S Goff

The Northern Sewerage Project (NSP) is a $650 M infrastructure project that will increase the capacity of the sewerage system for Melbourne’s growing northern suburbs while also helping to protect the Merri and Moonee Ponds creeks by significantly reducing the number of sewage overflows that can occur after heavy rainfall. The NSP consists of two stages: Stage 1 (NSP1) will be owned and operated by Melbourne Water Corporation, and Stage 2 (NSP2) will be owned by Yarra Valley Water and operated by Melbourne Water Corporation.Glass-fibre reinforced plastic (GRP) was used on both NSP stages, however, since Stage 1’s schedule for installation of GRP was slightly ahead of Stage 2’s, this paper will only focus on Stage 1’s use of GRP.NSP1 involves the construction of 7.9 km of new sewer tunnel ranging in diameter from 1.6 to 2.5 m, five main access shafts at depths of up to 65 m, and connections to the existing sewerage system including several access manholes. Construction began in 2007, and project completion is expected in 2012.The original design for NSP1 specified the use of high-density polyethylene (HDPE-) line precast concrete pipes as the final tunnel lining and HDPE-lined reinforced concrete for the access shafts and manholes. During construction, the rising cost of precast concrete pipes and the introduction of an additional GRP pipe supplier in the market justified a review of the tunnel final lining material. The contractor-proposed GRP pipe alternative was accepted for the final tunnel lining based on time and cost savings that were possible without compromising the design intent. After gaining experience with GRP through this design change, Melbourne Water Corporation reviewed and accepted GRP as the final lining for five smaller connection manholes. The use of GRP for the manholes was particularly inventive as the redesign made use of the approved tunnel GRP pipes as both a structural and corrosion-resistant lining.This paper discusses the use of GRP on NSP1; how the change in material, from concrete to GRP, affected the design philosophies assumed during detailed design; and how construction methods were modified to handle the less rigid GRP material. Details on the structural, hydraulic and durability considerations for the design are included, as are details about the time and cost savings and the quality and safety improvements that were achieved during construction.

Mar 8, 2011

By J Allen, B Oats, S Palaniandy, M Lollback

The Julius Kruttschnitt Mineral Research Centre has conducted an intensive VertiMill® (VTM) survey program at the Cannington mine concentrator as part of the ‘collaborative research in stirred milling technology’ program funded by Metso Minerals. Since 2003, Cannington has progressively added grinding capacity into the circuit through VTMs operating in secondary and regrinding duties. Cannington was one of the first mines to adopt this technology in secondary duty by installing two VTM-1500-WBs as part of a capacity expansion to produce sub-100 µm rougher feed. Subsequently, an additional VTM-800-WB was installed in the lead regrind circuit to prepare sub-20 µm cleaner stage feed.Several surveys were carried out to evaluate the VTM performance over a range of changed conditions. Among the key changes in operating variables were circuit power draw, feed rate and water addition to the bottom of the mill. The average specific energy for secondary duty was 3.7?kWh/t. The lead and zinc regrind mills consume 8.1 and 15.3 kWh/t respectively. Generally, the VTM installations have successfully prepared feed for rougher and cleaner circuits by reducing the top size into the floatable regime with steeper particle size distribution, which has led to enhanced recovery. The survey results show the success of VTM installations in secondary (receiving feed from autogenous circuit) and regrind duties.CITATION:Palaniandy, S, Powell, M S, Hilden, M, Allen, J, Kermanshahi, K, Oats, B and Lollback, M, 2014. VertiMill® performance updates in secondary and regrind duties at Cannington mine, BHP Billiton, in Proceedings 12th AusIMM Mill Operators’ Conference 2014 , pp 263–272 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 1, 2014

Process Study on Some Ag-Cu-Pb-Zn Polymetallic Ore in South China

Sep 13, 2010

By S R. Pecover

AustraliaÆs opal and sapphire mining industry has fallen from its peak in the 1980s and 1990s into a significant low today. This is not due to exhaustion of the resource, but instead an over-reliance of the Australian miner on achieving a fair price for the gemstone product from offshore middlemen dealers. Gemstone and geological research is also at a low as Federal higher education expenditure has fallen with research institutions relying increasingly on private funding in an environment of restricted autonomy and flexibility for researchers. What little remaining research skills the universities have is being bled into the private sector as a result of the mining boom and encouraged by lower than average academic salaries. Nevertheless, some highly innovative research has been taking place, often by self-funded individuals and retired academics simply with a desire to advance the understanding of the particular branch of science in which they are interested. New models for the formation of sapphire and opal are now beginning to be applied to the exploration for these gemstone commodities. This research, together with well thought out plans for managing the gemstone product through its value-adding steps to the jewellery retail level, has the potential to bring about a resurgence in the Australian gemstone industry.

Jan 1, 2008

By G Lumley

PlannersÆ optimism (or maybe commercial necessity) means that most mine plans use equipment rates that are rarely achieved (Lumley and Beckman, 2009). This lack of understanding of what equipment actually moves is causing erroneous equipment forecasts, leading to incorrect mine development plans and economic evaluations. Compounding this problem is a downward trend in actual equipment performance in some areas. Consequently, the presentation of realistic mine plans that are actually achieved in practice is not a common occurrence. However, rational, fact-based mine planning is available to those who want it. Hundreds of millions of cycles of data from open cut mining equipment has been collected from mines around the world since 1992. This unique and highly valuable databank is growing at an exponential rate and is being used by a number of our big miners to support rational and fact-based decision-making. However, neither the use nor the appreciation of the value of this data is universal. There is a challenge to everyone in the mining industry - how do you access value from it? The databank was drilled into and the results analysed for, the Australasian Mining and Metallurgical Operating Practices (AMMOP) publication (Lumley, in press). For this paper the analysis has been extended to include interpretation of trends for draglines, shovels, excavators and trucks. It investigates trends between coal and non-coal mines and across geographic areas. It is known that mining equipment performance in most sections of the industry is falling. This paper attempts to quantify the fall and provide explanations. The trends are analysed to extract the reasons behind the changes and most importantly, what can be done about it.CITATION:Lumley, G, 2012. Understanding trends in performance of open cut mining equipment, in Proceedings Project Evaluation 2012 , pp 203-224 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 24, 2012

This paper presents an overview of a program PC-BC developed for application to the design and evaluation of block cave operations. Conventional mine planning software tools are not well suited to the evaluation of this type of deposit. The paper looks at the modelling approach as applied to a block cave mining project. The following steps are described:Initial preparation of data including block models, draw point footprint geometry and draw cone geometry. Computation of individual draw point reserves. Procedure for modelling of vertical mixing of material within each draw point and subsequent determination of the best height of draw for each draw point based upon an economic cut-off value. Smoothing of draw heights amongst neighbouring draw points to produce a realistic draw envelope. Mineable reserves within the envelope are then computed. Tools for preparation and evaluation of various production schedules. This includes definition of draw rates, and rates for commissioning new draw points. In an operating mine, the capture and analysis of daily draw tonnages is important. How PC-BC accommodates this is described as well as the processes for depleting the draw column reserves. In the 12 years since the program was first developed, it has been used on a number of projects for feasibility studies and operating mines. Some practical examples of the use of the program in these projects are presented. Finally, some commentary on the sensitivity of various parameters is presented. Particular emphasis is placed on the overall footprint design.

Jan 1, 2000

By J Holdsworth, L Sutton, A Lavrinec, D Ilic

Air quality is a big topic of discussion in regional mining communities as well as urban environments situated close to port terminals handling bulk solids. Community perception of poor air quality can significantly affect the reputation of the mining operation and handling facilities. Dust monitoring for regulatory compliance relies on using a handful of accurate but very expensive sensors, usually situated at the boundary, relatively far from the activities that generate the airborne dust. These reference monitors measure dust leaving the site but dust mitigation and management on-site largely relies on operator judgement. At a fraction of the cost, small wireless solar powered units can be used to supplement reference monitors in real-time. Due to their compact nature, portability and low price, these units can be implemented on a mass scale to increase spatial resolution of dust measurements and, more importantly, in much closer proximity to both the dust generating activity and the sources of dust. This can provide valuable insights into the origins and timing of dust generation thus producing datadriven decision-making while minimising subjectivity. Similarly, light detection and ranging (LiDAR) is another supplemental technology that can be used to increase the spatial resolution of dust measurements in near real-time, however, the cost of commercial systems even exceeds that of regulatory monitors. LiDAR also presents difficulties in quantifying dust plume concentrations. This study presents learnings of implementing both technologies for dust emissions management. Several low-cost sensor units and a fast-scanning custom-built 3D LiDAR system operating at a range of 1.5 km with a resolution of 1.5 m were deployed on a surface mine to monitor dust emissions from different activities. The project explores the use of real-time sensor data to quantify LiDAR measurements in parallel with integration into mine planning. The approach can assist in prioritising dust mitigation activities thereby reducing instances of emissions exceedance and minimising water use through databased and targeted application. Demonstrated is an opportunity for a step-change in industry best practice as well as commercialisation and operationalisation of the method across different industries, including future mineral extraction.

Sep 18, 2023

Operating well designed and maintained surface mine haul roads is the key to minimising truck haulage costs - in itself a significant component of the total cost per tonne mined. Existing and proposed mining operations are subject to scrutiny, both from the economic and environmental perspectives. In the long run, this scrutiny returns improved efficiencies and leaner, 'greener' operations. The focus of this evolving evaluation process should and will certainly fall on haulage operations - simply by virtue of their contribution to overall cost of operations and sustainability impacts. Whilst the end result - improved efficiency and contributions to resource sustainability - is not in itself problematic, it is the route, or process followed to achieve these improvements that needs to be carefully managed. We can be guided on this journey by our understanding of how a road is designed, and, critically, the technological solutions that can contribute to a company's sustainability initiatives. This paper examines the current state of mine road design and operation, together with the economic and environmental issues associated with under-performance. The paper serves as a basis for evaluating the economic and environmental contributions that technology in road design and management can deliver to sustainable operations. Utilising innovation is the key to long-term sustainability and as a means of positioning the industry for the imminent structural changes to the economy and environment, changes which are now within the operating life of many mines, haul roads and haul trucks.

Jun 1, 2010

A new porphyry copper gold district has been discovered at Goonumbla near Parkes in central New South Wales. Endeavour 26 North is the largest deposit known to date with a possible resource of 166.4 million tonnes at 0.74% copper, 0.12g/tonne gold and 1.7g/tonne silver, using a cut-off grade 0.3% copper. Mineralisation is primarily bornite in the higher grade zones and chalcopyrite in the peripheral lower grade zones. Most of the copper, gold mineralisation is associated with potassic alteration. Two mineralised quartz monzonite porphyry intrusive stages have been identified and these are related at depth to a large monz- onite stock which may have been the source of some of the mineralisation. On the basis of detailed paragenesis studies, the potassic zone can be divided into three symmetric subzones. The low grade inner potassium feldspar subzone is confined to the later intrusive porphyry. The outer potassium feldspar subzone is the most highly mineralised alteration halo due to the focussed superimposition of two hydrothermal cycles which have overprinted intrusive and volcanic rocks. The fringing biotite potassium feldspar subzone reveals alteration minerals which are developed early in the paragenesis. Fracture controlled quartz sericite alteration with low sulphide content, fringes and, in part overprints the potassic zone. The restricted pipe-like nature of the alteration zones and related mineralisation suggests that Endeavour 26 North is repres- entative of a multiphase focussed porphyry copper gold system.

Jan 1, 1986

The Sams Creek gold deposit near Takaka in northwest Nelson was discovered in 1974 by CRA Exploration (CRAE) geologists. CRAE recognised the potential of the area and subsequently undertook a comprehensive exploration programme of geological mapping, soil and rock-chip sampling, geophysical surveys and diamond drilling. Exploration defined sporadic gold mineralisation contained entirely within a deformed and hydrothermally altered, peralkaline granite porphyry dyke with a seven kilometre strike length, and up to 60 m thickness. Rock chip samples indicated extensive and economically significant gold grades over approximately one kilometre strike of the dyke at Main Zone prospect. CRAE completed 30 diamond drill holes at this prospect and defined a limited resource. Oceana Gold Limited recommenced active exploration at the Sams Creek Project in late 2002, focusing on improving the geological understanding and known resource at Main Zone. Completion of 1041 m diamond drilling successfully increased the estimated resource to 10.7 Mt @ 2.12 g/t Au containing 729 000 oz at a 0.7 g/t cut off. A further campaign of 1560 m diamond drilling was undertaken in 2003 - 2004 to extend the resource and test the continuity of high grade mineralised zones. Deeper intersections of the porphyry dyke indicated geometrical complexity and grade variability similar to that observed at shallow levels. Recent research suggests that Sams Creek can be geologically classified as a variant of intrusion-related gold systems, and therefore comparable to some other, very large gold deposits. However, due to the rugged terrain and dyke geometry, surface drilling is reaching the limits of viability at Main Zone. If infill drilling continues to be successful then an underground decline may be developed to facilitate further exploration. Potential also exists along strike, where other significant gold anomalies are known but largely untested by drilling.

Jan 1, 2004

By D P. Blair

There are two major aspects to wall control blasting – the potential for any blasthole to cause wall damage and the potential for a delayed sequence of blastholes to cause damage. The damage potential of individual blastholes is governed by standoff distance and charge weight. However, for locations sufficiently close to a highwall, dynamic finite element models and field measurements show that there is also a critical nature to those blastholes very close to the wall, over and above standoff distance. At many mine sites, the charge weight/standoff-distance is set by trial and error. Thus, a significant aspect of the present work is the determination of dynamic stress radiating from a blasthole. Unfortunately, the modelling and measurement of this dynamic stress is still faced with many difficulties. Typical models have questionable aspects, which casts serious doubt over their predictions, and it is shown that the Hustrulid Bar experimental technique does not correctly account for stress wave attenuation in extended media. In an attempt to solve the dynamic stress problem, the present work describes a model based on an exact solution under the assumption of viscoelastic material. The model takes full account of the rock mass elastic/viscoelastic properties, the explosive type, geometry and primer location and predicts a dynamic stress for direct comparison with the unconfined compressive strength of the local rock mass. This model predicts the standoff distance required to avoid damage due to a single blasthole. The behaviour of a delayed sequence of blastholes is analysed using an upgraded waveform superposition model, covering a range of initiation delay combinations, which predicts the peak particle motion (PPM) induced in the wall for each combination. This approach shows that there is no need to fire dedicated trim shots close to walls; all that is required is a carefully modified production shot. The mechanism of vibration screening is discussed, and its use in a superposition model highlights the potential of reverse firing (shield blasting) to reduce wall PPM. A conceptual model is also introduced to give a further insight to vibration screening and damage (via ground heave). This model predicts that a centre-lift blast will have a central heave profile and that a reverse-fired shot will produce a smaller power trough than that produced by a standard shot. It is demonstrated that the mechanism of presplit formation is not well understood; nevertheless, experimental evidence shows that presplits can be an effective method for reducing wall vibrations.CITATION:Blair, D P, 2015. Wall control blasting, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 13–26 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015