Search Documents

By E. M. Murphy

(Presented by invitation at a meeting of the Spokane Local Section of the Institute, Feb. 17, 1912.) EIGHT years ago the Hecla mine, a lead-silver producer, situated at Burke, Idaho, was producing ore from but two levels, the 300- and the 600-ft. All hoisting was done with a 12- by 16-in. slide-valve, double-reel, hoist. The hoist was being worked to its capacity and was unsuitable for hoisting from greater depths. As the work of opening a new level was about to be started, it became necessary to remodel the then-existing equipment or install a new hoist. The recent advent of electricity from Spokane had made available a cheaper power than steam. By a series of tests conducted throughout the Coeur d'Alène district, it was found that it cost $109 per year to generate a horse-power with steam. Electric power was to be had for $50 a horse-power per year. It was decided to substitute for the engines a motor-drive, of sufficient capacity to operate from the 900-ft. level, and ultimately install an entirely new hoist. After disconnecting the engines, installing a new shaft, and making a few minor changes, a 300-h-p., 2,300-volt, 514-rev. per min., variable-speed motor of the induction type was geared to the reel-shaft. The reels were supplied with 3/8 by 4-in. flat rope, and the duty of the hoist was about as follows: Cage, 1,700; ore, 2,600; car, 1,400; rope, 2,250; total, 7,950 pounds. The Bristol ammeter chart, Fig. 1, shows the combined current-consumption of the hoist- and mine-motors. The large intermittent load is clearly shown ; this produced harmful fluctuations in the voltage of the long, lightly-loaded, 60,000-volt transmission-line from Spokane to the Coeur d'Alènes. The power company received no compensation for the increased cost of producing power for this intermittent or fluctuating load. In order to protect its system from similar excessive

Sep 1, 1912

By Lucien Eaton

VENTILATION in the iron mines of the Lake Superior region in nearly all cases is natural; that is, it is induced by the difference in elevation between different outlets in the mine and by the difference in temperature of the air in the mine and that outside. This difference in temperature is frequently augmented by placing a steampipe in the upcast shaft; but aside from this, artificial aids to ventilation have been rare until - recent years. In some of the older mines, as at the Cliffs Shaft mine at Ishpeming, Mich., in the 80's, fans have been used when there was only one opening to surface, but their use was abandoned as soon as a natural circulation of air started. In recent years, the Newport mine at Ironwood, Mich., was the first to use positive mechanical ventilation. The installation was not large enough, however, to give definite results, reliance being placed largely on natural ventilation. With the coming of warm weather in the spring of 1914, the necessity of positive mechanical ventilation at the Lake mine of the Cleveland-Cliffs Iron Co. at Ishpeming, Mich., became evident. The workings of the Lake mine are under the bed of old Lake Angeline, which was pumped out in 1894, and the mine had been in operation for 6 years prior to that date making a total of 26 years of continuous operation. The total production, up to 1914, amounted to over 8,000,000 tons. The ore was first mined by square-set rooms and pillars, but this was later changed to top slicing and caving. Both methods required the use of large amounts of timber, probably 80,000,000 board feet in all, practically all of which remained in the timber mat. The slow oxidation of this timber was one of the principal causes leading to the installation of mechanical ventilation. The mine was served by only one working shaft, called No. 4, a second outlet being provided by a raise to the surface from the old workings on the south side of the mine. This raise was the "down cast;" but it was very small and the drifts and raises leading to it were too small and crooked to permit an adequate amount of air to enter the mine, especially during the warmer weather. Measure-

Jan 8, 1920

By Arthur R. MacPherson

The development of a simple method to predict the autogenous grinding possibilities of new ore deposits is attained. This method employs a 45-cm (18-in.) dry grinding Aerofall mill to grind small quantities of core or crushed samples in the top size range of 2 to 5 cm (1 to 2 in.). An extensive program has been carried out to correlate the data obtained in the 45-cm (18- in.) test mill with the actual results obtained in large commercial plants or autogenous test plants. Enough evidence now exists from these correlation programs that the 45-cm (18-in.) mill can be used to grind small samples from a new deposit and correctly predict the autogenous grinding mill requirements of a commercial plant to treat this ore.

Jan 1, 1978

By George A. Jr. Dornin

A TRULY sound ingot can be made only from steel that is completely deoxidized. Given this condition, there is one further basic requirement-the steel in the ingot must solidify progressively from the bottom to the top. Any method of making the ingot that produces this type of solidification will yield sound products. Since a big-end-down ingot will not satisfy this condition, all sound steel today is produced in big-end-up ingots, the standard tool being the big-end-up mold fitted with some sort of refractory hot top. No one uses hot tops from choice, be cause of the bother and expense involved and because of the low yield resulting from their use-they are used because there has been no alternative where sound steel was required.

Jan 1, 1947

By J. C. Boswell, J. D. Crawford

IN addition to its base-metal and coal mining operations, the United States Smelting Refining and Mining Company has, for the past quarter century, been one of the few large American mining companies interested in dredging. Its activities in this field are confined to gold, and to Alaska, but it is the largest operator in that territory, with twelve huge dredges available to work during the summer on the frozen ancient beach sands at Nome and the gravels of Fairbanks. These operations will be described separately.

Jan 1, 1948

By R. V. Taborelli, P. B. Bucky

This investigation was carried on by means of models and the application of the principles of similitude to determine the effects of props, props and cribs and sand filling in longwall mining. The geologic structure and rate of face retreat were kept constant and the only change introduced was in the method of support. It is not felt necessary to repeat a description of apparatus, or to explain the fact that a scalar model made in all parts of the same material as the prototype will behave similarly to the prototype when rotated at speeds such that the centrifugal force is as many times the gravitational force as the prototype dimension is a similar linear model dimension. The reader is referred to earlier papers1,2 for further information regarding these statements. All models were made of sandstone and were as in Fig. 6. They are composed of a 3/16-in. ore body bed A, overlain by a 3/16-in. bed B, a ?-in. bed C and two ?-in. beds D and E. The model was rotated at + 2350 r.p.m. equivalent to a model ratio of 1268. It was worked back ¼ in. at a time before being replaced in the centrifuge and again rotated. Table 1 gives model and prototype dimensions occurring in this discussion, the prototype dimensions being 1268 times the model dimensions. Figs. 1, 2, 3 and 4 were taken while the model was rotating at 2350 r.p.m. One was taken for each face retreat of 26.4 ft., but for obvious reasons all are not presented. Fig. 1 (A-E) shows the behavior of this type of structure with face retreats of 26.4 ft. and no artificial support. Fig. 2(A-E) shows the behavior of this type of structure where breaker and face props were used. The props were exceptionally strong, being of steel ? in. square in cross section, and capped with 1/16 in. ± of soft wood and paper, to allow for roof deflection. The face props were

Jan 1, 1940

By P. B. Bucky, R. V. Taborelli

This investigation was carried on by means of models and the application of the principles of similitude to determine the effects of props, props and cribs and sand filling in longwall mining. The geologic structure and rate of face retreat were kept constant and the only change introduced was in the method of support. It is not felt necessary to repeat a description of apparatus, or to explain the fact that a scalar model made in all parts of the same material as the prototype will behave similarly to the prototype when rotated at speeds such that the centrifugal force is as many times the gravitational force as the prototype dimension is a similar linear model dimension. The reader is referred to earlier papers1,2 for further information regarding these statements. All models were made of sandstone and were as in Fig. 6. They are composed of a 3/16-in. ore body bed A, overlain by a 3/16-in. bed B, a ?-in. bed C and two ?-in. beds D and E. The model was rotated at + 2350 r.p.m. equivalent to a model ratio of 1268. It was worked back ¼ in. at a time before being replaced in the centrifuge and again rotated. Table 1 gives model and prototype dimensions occurring in this discussion, the prototype dimensions being 1268 times the model dimensions. Figs. 1, 2, 3 and 4 were taken while the model was rotating at 2350 r.p.m. One was taken for each face retreat of 26.4 ft., but for obvious reasons all are not presented. Fig. 1 (A-E) shows the behavior of this type of structure with face retreats of 26.4 ft. and no artificial support. Fig. 2(A-E) shows the behavior of this type of structure where breaker and face props were used. The props were exceptionally strong, being of steel ? in. square in cross section, and capped with 1/16 in. ± of soft wood and paper, to allow for roof deflection. The face props were

Jan 1, 1940

By JOHN A. FULTON

THE Comstock Lode is in Storey County, Nevada, and extends in a north and south direction through the towns of Virginia City and Gold Hill, with a total length of 4.27 miles. Its mines have produced silver and gold to a known value exceeding $400,- 000,000 since 1859, when the work first began. More than $126.000,000 was paid in dividends by the mining companies, although much more than this was probably realized from the ore, because many milling companies were independent companies owned by the directors and superintendents of the mines. The milling companies' contracts called for an extraction of only 65 per cent and, as much of the ore was worth $100 a ton and up- ward, they must have recovered substantial amounts for their own accounts over and above this guarantee. Gold was discovered in the spring of 1850 by a party of Normons bound for California. The discovery was made at the mouth of Gold canyon near Dayton, on the Carson River, about 10 miles south of Virginia City.

Jan 1, 1929

By J. C. Bradley

THE relation of annealing temperature to conductivity of copper wire has been determined.1 Conductivity hard was 98.26 per cent. After a 10-min. heating at 200° C. it was 98.69. By annealing 10 min. at 300° C. a large increase, to 100.93, occurred. Maximum conductivity, 101.15, was attained after a 500° C. anneal; thereafter it decreased to 100.53 after a 950° C. anneal. If copper is gassed the decrease is much more than this. MATERIAL AND METHOD The work was done on high grade electrolytic copper, 99.942 per cent. copper-plus silver, silver 0.0008 per cent. It was hot-rolled to 3 in., then cold drawn to 0.080 in. The wire was cut into 25 5-ft. lengths and numbered 1 to 25 as cut. Four samples were tested hard. The others were wound into 5-in. diameter coils. For the 100° C. heating a coil was put into water, the water brought to boiling, and the wire kept at this temperature for 10 min. For the higher temperatures the coils were placed in envelopes of sheet copper, a little water added, and the envelopes sealed by folding over the edges twice, and hammering them together. This kept the air out very well. The envelope and wire were brought to the desired temperature; this was maintained for 10 min., then the whole was water-quenched.

Jan 1, 1927

By John H. Schissler

INTRODUCTION AND SUMMARY Complex copper-lead-zinc ore is mined from underground workings high in the Western Cordillera of the Andes mountains about 100 km in a stralght line north of the city of Arequipa in southern Peru. The Madrigal mine is situated in a steep-walled canyon into which the six operating levels "daylight". Production is from cut-and-fill stopes currently producing approximately 740 dry metric tons per day. The Santa Rosa vein, the most important producer in the district, outcrops for a distance of about 4 km, bearing N 75º W and dipping about 70º NE. In places the vein splits into two or three branches; widths of each vary between 1 and 4 m and total mineralized widths of up to over 8 m occur. Principal ore minerals are chalcopyrite, galena and sphalerite. Ore reserve grades for the Madrigal mine average about 1.45% Cu, 2.6% Pb and 5.0% Zn, 2.9 ozAg per metric ton. [Compania] Minera del Madrigal is a California limited partnership; the general partner and operator is [Compania] Madrigal, a wholly-owned subsidiary of Homestake Mining Company. HISTORY Shallow workings found on the Santa Rosa vein were probably made by the Spaniards during colonial times in their search for

Jan 1, 1977

By R. E. Zimmerman

Wide attention is being placed upon various methods for cleaning the fine sizes of bituminous coals. The author describes and analyzes the results achieved on wet concentrating .tables of modern design on unclassified feeds of - 1/2 in. particle sizes, including tests on high-sulphur coals.

Jan 1, 1950

By CLARENCE WM. POY

THE most common difficulty faced by an engineer or mine operator when opening a new property in a new field is the lack of roads and of cheap transportation. This one item often swings the balance of success or failure in starting a project. In Alaska, as elsewhere, such problems are more or less serious. In the boom days around the Valdez district, as well as in other parts of this territory, freighting was accom¬plished by dog teams or horses, or even by men that were willing to put their shoulders into harness, because there were virtually no roads. More important, there was only one time when supplies could be transported, and that was when there was suffi¬cient snow on the ground following a heavy wind. Then, and only then, could one depend on the snow to support horses and sleighs, and be sure that the gulleys, streams, and crevices in the glaciers were filled with snow to avoid pitfalls. These methods were used when one had no roads, no streams in the summer to float a barge, or even a trail for a pack train. If the snow was deep and soft, trans

Jan 1, 1935

By E. Marburg

Most ingots complete solidification vertically rather than transversely. This conclusion is based on complete solidification patterns of big-end-up and big-end-down ingots developed from dumped and split ingots. New mechanisms for segregation in ingots are proposed. Internal soundness in ingots is found to depend upon adequate width of vertical core. A LTHOUGH it has long been recognized that the A internal soundness of ingots is principally been recognizedthatthedependent on the process of solidification, knowledge of this process is still only fragmentary. The mechanisms causing the several types of segregation in ingots, which mechanisms are necessarily related to the solidification process, are not well understood. In absence of a better conception of the solidification process, it seems hardly surprising that mold design varies widely. Guiding principles for mold design are needed. At stake in the improvement of ingot quality are not only improved properties of steel but also appreciably higher yields of sound steel, which would considerably decrease manufacturing costs. In the present study, following a general description of the several types of segregation in ingots, Fig. 1, complete solidification patterns of a big-endup and a big-end-down ingot, including the zones of accelerated solidification, have been reconstructed. In both ingots, a core of vertical solidification extends from the base cone to the hot-top junction. Based on the finding that ingots complete solidification vertically rather than transversely, as has been previously assumed, new mechanisms for segregation in ingots are proposed. Internal soundness in ingots is found to depend upon the width of the vertical core, which in turn depends principally upon the width to height (w/h) ratio of the ingot. Solidification patterns of ingots are of three general types: 1—those in which vertical solidification does not reach the top, 2—those in which vertical solidification just reaches the top of the ingot, and 3—those in which vertical solidification reaches the top some time before transverse solidification would reach the middle of the ingot, so that a vertical core of definite width at the top of the ingot is developed. Axial defects vary characteristically with the solidification pattern. Examples of ingots of each type are presented. Dumped ingot data reported by Nelson' have been used in developing families of curves of transverse and vertical solidification, and in deriving the effect of the w/h ratio upon the solidification pattern. Photographs of many ingots split at Homestead and at Duquesne Works, United States Steel CO., as well as those published by the British Iron and Steel Institute,' have been studied and analyzed. In the interest of brevity, only typical ingots of each type or classification from the above sources have been reproduced. Segregation in Ingots Segregation in ingots falls into three principal classifications: 1—lamellar segregation, as revealed in sulphur prints (Figs. 2 and 3); 2—zone segregation, or broad variations in composition; and 3— interdendritic, or microsegregation. The last class, of minor importance, is not considered here. When liquid metal cools, according to the theory of differential or selective solidification,2 metal of relatively high purity selectively solidifies first. Liquid segregates (principally carbon, phosphorus,

Jan 1, 1954

By E. G. Dahlgren, Dan O. Howard

THE West Edmond oil field, which covers parts of Oklahoma, Canadian, Kingfisher, and Logan Counties in the State of Oklahoma, is in geographical extent the largest single oil field found in the state. At the present time, its area of 26,800 acres is almost twice as large as the Oklahoma City field, which hitherto was the state's largest field. Many authorities believe that the West Edmond field is the most important oil pool found in the United States since Pearl Harbor. The discovery of the field without the help of geological, geophysical, or other recognized technical information, the fact that the oil and gas accumulated in a stratigraphic or wedge-type trap, and the rapid development of the productive area under wartime conditions are some of the interesting features of the field. The West Edmond field lies west of the Oklahoma City, Britton, and Edmond fields. The field is in an area that has been considered on the west flank of the Granite Ridge line of folding, on which a number of Central Oklahoma's most important oil fields are located. Over a period of years, especially since the discovery of the new pools such as Oklahoma City, Edmond, Britton, and Crescent, the general area of the West Edmond field has been explored intensively by geological and geophysical methods. This led at times to the drilling of a few dry Wilcox sand tests.

Jan 1, 1945

By Joseph H. Allen

In the old Kentucky reports, made by the Survey of which Prof. Owen was director, the veins of the Western Kentucky coal-field were numbered from 1 up to 12. Later Prof. Shaler used letters, beginning at the top. For instance, Owen's 12 is Shaler's A.

Jan 1, 1888

By John M. Hartman

An examination as to irregularity of wear around the nose of the Witherbee tuyeres showed a section through the nose near the top as per Fig. 1, and a section only a half-inch beyond as per Fig. 2. The molten iron flowing over the nose of the tuyere had melted off the metal until the water in the tuyere prevented further melting. These tuyeres have a division in the annular water-space (see Fig. 2) to turn the current of water at the top, and the watersupply pipe is carried to within 1 inch of the nose. The constant supply of cold water in the nose of the tuyere kept it well cooled and preserved. But half an inch on the other side of the division the metal had melted off, as is shown by Fig. 1. There was no means of effecting a circulation at this point so long as the water was discharged from the butt of the tuyere. A pipe having been placed on the discharge-side of the division, the same as on the supply-side, in order to secure a circulation of the water at the nose on the discharge-side, it was found that the metal did not burn off. The nose being found to give out at the bottom, a division was placed in the annular water-space at the bottom, terminating 1 inch from the nose. This made a sharp current of circulation in the nose at the bottom, and prevented the burning of the metal there. A positive circulation at the nose, top and bottom, is a necessity with the present fast driving of furnaces, and prolongs the life of the tuyeres. The proper metallic composition of tuyeres is a question constantly agitated. A trial of ordinary yellow-metal* tuyeres was made 12 years ago. They did their work just as well

Jan 1, 1899

By S. W. Poole, J. A. Rosa

The object of this investigation was to determine the distribution of chemical elements within a large, killed alloy-steel ingot, by sulphur printing and quantitative chemical analysis. With regard to segregation in steel ingots, the factors of melting practice, pouring temperatures, mold design, etc., and the mechanics of solidification and its attendant functions, have been the subject of intensive study over a period of years by many investigators. Notable among these is the Sub-committee of the No. 5 Committee of the British Iron and Steel Institute. For an exposition of the many problems awaiting the researcher on the heterogeneity of steel ingots, the methods of attacking these problems, together with some of the answers, the reader is referred to the nine reports and numerous papers of that committee and its membership. Steelmaking Data Melt.—The heat was made in a 70-ton direct arc-type basic electric furnace. Furnace charge consisted of nickel-chromium-molybdenum steel, most of it in the form of heavy mill scrap. All of the scrap was charged cold. The standard double-slag method was employed, the heat being finished under a strong carbide slag. Aluminum was used as the deoxidizing agent. Tapping tempera- ture, as observed with an optical pyrometer, was 3000°F. Detail of Mold and Ingot Size.—Details of the ingot mold and the ingot itself are given in Fig. I. Teeming.—Teeming temperature of the subject ingot as observed with an optical pyrometer was 2830°F. The ingot was top-poured directly through a 1 1/2-in. nozzle and required 7 min., 44 sec. to fill up to the hot top. An additional 2 min., 30 sec. were required to fill the hot top. The ingot was stripped hot and charged with the remainder of the heat into an annealing furnace. There it was given the standard annealing cycle used for these ingots. Subsequent heat-treatments are described elsewhere in this paper. Sectioning and Preparation for Sulphur Printing Because of previous favorable experience in sectioning ingots up to 21 1/2 in. square with an oxyacetylene torch, it was decided to use this method to section the subject ingot. The ingot was preheated to 900°F. for 12 hr. It was then placed on a steel bed in a horizontal position so that the longitudinal axis was level and parallel to the track of the motor-driven torch carrier. Two cuts were made, one 2 in. above the longitudinal axis and the other 2 in. below. The time required to make each cut was approximately 75 min. The cutting operation is shown in Figs. 2 and 3. The 4-in. thick slab was mmediately charged into a furnace standing at 1200F.

Jan 1, 1945

By L. T. Larson

The spectral reflectivity of zirconium in light of 441 to 668 nanometers (nm) wavelengths and air immersion has been determined. Bireflectance and apparent-angle -of-rotation measurements show zirconium to be optically isotropic when examined in light of approximately 484 nm wavelength. There is a direct relationship between bireflectance and the tilt of the basal pole of zirconium from the surface normal. This relationship allows the determination of the spatial orientation of the basal pole of an individual single crystal within a coarse-grained poly crystalline section to within± 2 to 3 deg for angles of basal pole tilt from 0 to 90 deg. In recent years considerable attention has been given to the quantitative determination of optical properties of opaque minerals by use of vertically incident, plane-polarized light. In particular, Cameron' and Cameron et a1.2 have developed criteria for the identification of a large number of anisotropic ore minerals based upon measurement of the apparent angle of rotation and the ellipticity or phase difference of the reflected light. It was shown by Larson and Pickle-simer3 that apparent-angle-of-rotation measurements may also be used to determine crystallographic orientations of grains of noncubic metals. In particular, it was shown that the basa.1 pole orientation in space of zirconium grains can be determined to ±3 deg for those grains with basal pole tilts of 10 to 90 deg from the plane of the section. Another, even more widely studied, optical property is reflectivity. cameron4 has commented upon measurement of the reflectance of plane-polarized, vertically incident light and Bowie and Taylor5 have made such measurements an integral part of their system of ore-mineral identification. Leow6 has reported on the spectral reflectivity of molybdenite and has used reflectivity values to calculate refractive indices and absorption coefficients. Cameron7 has made use of reflectivity values to ascertain aniso-tropic ore mineral symmetry and Piller and v. Gehlen8 have evaluated sources and importance of errors in reflectivity measurements as applied to calculation of optical constants. cambon9 has shown that reflectivity measurements using vertically incident, plane-polarized light are useful in the investigation of metals and in the identification of phases present in alloys. Bronson10 has made preliminary measurements on the optical anisotropy of beryIlium and Mott and Haines11 have published qualitative data on the intensity of light reflected from sections of bismuth, tin, and aluminum when these metals are microscopically examined under crossed polarizing plates. Koritnig12 has correlated the reflectivity of homogeneous solid solutions with their chemical compositions. From the above work and investigations in progress by this author, it is apparent that accurately determined values for the reflectance of vertically incident, plane-polarized monochromatic light from carefully polished surfaces of noncubic metals can prove useful in identification, composition determinations, and crystallographic orientation applications. Finally, reflectivity values, when measured in two media of differing refraction index and related to standards whose spectral reflectivities in these media are known, can be used to calculate optical constants such as refractive index and absorption coefficient. These constants may prove of use to those concerned with problems of electron band configuration. This paper reports the spectral reflectivity of zirconium measured in light of 441 to 668 nanometers (nm) wavelengths and air immersion. It also gives maximum bireflectance values for a prism section of zirconium in these wavelengths and shows how bire-flectance may be used to determine the crystallographic orientation of zirconium single crystals. Because of the lack of information on the reflectivities of the standards in oil immersion, no attempt is made to calculate the refractive indices or absorption coefficients although it is recognized that such values may be of fundamental importance. METHOD Single crystals of zirconium were cut by electro-discharge machining from a single-crystal rod grown from iodide bar by an electron-beam zone-melting process.13 The crystal sections were mounted in cold-setting epoxy resin and mechanically polished to a plane, uniform, bright surface. Each crystal was then chemically polished in a 26/26/43/5 mixture (by vol) of water, nitric, lactic, and hydrofluoric acids to remove the mechanically damaged and smeared surface layer. Final polish was obtained by electropolishing at 30 v in a bath of methyl alcohol and perchloric acid (98/2 by vol) at -70oc.14 Reflectivity measurements were made using a photometer system designed and developed at Oak Ridge National Laboratory and described in detail by Larson.15 Briefly, the reflectivity measuring system consists of a reflecting microscope; a double-beam, null-balancing photometer array; a mechanically driven microscope stage; and a direct X-Y readout of the reflectivity of the specimen relative to its orientation on the microscope stage. The measuring photometer receives its signal from the specimen through a slotted Wright occular placed on top of the photovisual head of the microscope. The reference photometer receives light through a flexible glass "light pipe" from a mirror in the reflecting system of the microscope. Monochromatic light is attained through use of interference filters (15-nm half-peak width pass bands) placed in front of a stabilized Vickers 12 v, 100 w, tungsten-filament, quartz-iodide lamp.

Jan 1, 1970

By W. C. Ellis, M. E. Fine

INTRODUCTION IN the iron-cobalt system there are several property-composition relationships of theoretical importance. The alloys are ferromagnetic exhibiting a maximum saturation at approximately 33 at. pct cobalt;1 the interatomic distances at room temperature show large positive deviations from Vegard's rule;2 and in the region of 50 at. pct cobalt there is an order-disorder transition which has a large effect on other properties. The thermal expansion data for the system have been reported3,4.5,6 only from room temperature to 100°C, and for this temperature range a minimum in coefficient in the region of 50 at. pct cobalt is well established. 3,4,6 This paper reports the expansion properties in the iron-cobalt system for temperatures from 30 to 850°C, shows the correlation with other physical properties, and proposes an explanation for the interrelation. EXPERIMENTAL PROCEDURE The thermal expansivities of iron-cobalt alloys in 10 pct steps in composition were determined from 30 to about 850°C. The major series of alloys was prepared by induction melting from Armco iron and cobalt rondelles with the addition of about 0.6 wt pct manganese. This series was supplemented by three compositions: high purity electrolytic iron, high purity electrolytic cobalt, and an alloy of 52.1 wt pct cobalt prepared from the high purity electrolytic iron and electrolytic cobalt by vacuum-melting. The compositions of both series of alloys are given in Table I. The specimens for measurement were prepared from the cast ingots by first hot-swaging followed in most instances by cold-swaging to 0.180-in. diam rod. Some alloys in the region of 50 pct cobalt, because of inherent cold-brittleness, were swaged hot to the final diameter. The expansion specimens were approximately 2 ½ in. long with flat-ground and polished ends. Before measurement they were annealed in hydrogen for r hr at 900°C. In the apparatus used for the thermal expansivity measurements (Fig I), a modification of that designed by Hidnert and Sweeney,7 the differential expansion between the specimen and vitreous silica was measured by a dial micrometer reading to 0.001 mm. An invar fixture supported the dial gauge, and this fixture, in turn, was connected to a split invar collar which supported the outer silica tube. A pyrex "T" was placed over the outer silica tube and was sealed to the invar collar by Apiezon Q sealing compound. A movable hollow vitreous silica rod which rested on top of the test specimen slid through a flexible rubber diaphragm cemented to the top of the pyrex "T." The specimen rested on a vitreous silica pedestal fused into the outer tube and was kept centered by a silica sleeve. A non-oxidizing atmosphere was obtained by admitting hydrogen into the

Jan 1, 1948

By Earl S. Greiner, Eric R. Jette

ALTHOUGH the mechanical and chemical characteristics of certain iron-nickel-silicon alloys have been investigated,1 the available literature shows no results of a systematic investigation of the constitution of this system. This paper describes the results of an X-ray investigation of the constitution of the iron-rich iron-nickel-silicon alloys at 600°C. Data on the constitution of the included binary systems obtained in other investigations have been correlated with the structure of the ternary alloys. Jette and Foote2 have presented a tentative constitutional diagram of the iron-nickel system following X-ray studies on quenched specimens. This diagram shows that the alloys at 600°C. containing from zero to approximately 4 atomic per cent nickel consist of a body-centered cubic (alpha) phase, the alloys containing 4 to 24 atomic per cent nickel consist of body-centered cubic (alpha) and face- centered cubic (gamma) phases, and the alloys containing from 24 to 100 atomic per cent nickel consist of a face-centered cubic (gamma) phase. These investigators recognized that it was not possible to retain the gamma phase in equilibrium by quenching alloys containing less than approximately 25 atomic per cent nickel and that high-temperature X-ray methods were desirable to determine the gamma-phase solubility limit. In a later investigation of the iron-nickel alloys, Owen and Sulley3 determined the alpha-phase solid solubility limit to be 3.5 atomic per cent nickel at 600°C. High-temperature X-ray methods showed the solid solubility limit of the gamma phase to be 14 atomic per cent nickel at 600°C. Since the high-temperature X-ray method should reveal equilibrium conditions in these alloys better than the quench method of other investigators, the results of Owen and Sulley pertaining to the gamma-phase boundary are to be preferred. As the result of an X-ray investigation of quenched iron-silicon alloys, Greiner and Jette4 have shown these materials to consist of a body-centered cubic (alpha) phase containing from o to 26.4 atomic per cent silicon at 600°C. The alloys containing from 26.4 to approximately 50 atomic per cent silicon consist of two phases at 600°C.; namely, alpha and eta. The eta phase corresponds to the stoichiometrical formula FeSi (33.4 wt. per cent Si).* The literature pertaining to the constitution of the nickel-silicon alloys has been reviewed by Ackerman,5 who found disagreements in the results of various investigators on several parts of the system. Subsequent data on the constitution of the nickel-silicon alloys were reported by Osawa and Okamoto.6

Jan 1, 1943