Search Documents

By W. W. Krech, T. E. Perkins

As fractures are propagated through rocks, energy is absorbed near the extending crack tip. Apparent surface energies for several rocks have been measured by cleavage under dynamic con-ditions. At nominal crack velocities from 0.5 to 500 in (min, measurements showed that fractures propagated in discrete jumps. Calculated surface energies and moduli were relatively insensitive to nominal rate of cleavage. in another set of experiments, rocks were cleaved under high confining stresses. The rocks were submerged in low leak-off fluids which formed a filter cake on the freshly cleaved surfaces (similar to the hydraulic lracturing process). Apparent surface energies were increased substantially as the surrounding fluid pressure was increased. Moduli in bending increased significantly upon application of the first 1,000 psi but were insensitive to stress level at greater pressures. INTRODUCTION For almost 20 years, hydraulic fracturing processes have been utilized effectively to stimulate oil and gas wells. During this period, some process improvements have resulted from studies of fracture orientation, mechanics of fracturing, areas generated, conductivities of cracks, etc. Yet many questions remain concerning the conditions and pressures needed during fracture propagation. In this paper we will report additional studies of the mechanics of fracture extension. It was shown previously3 that large rock samples could be cleaved under controlled conditions so as to measure the apparent surface energy (that amount of energy absorbed per unit area of new surface created). In this paper we consider the effects of two additional factors on surface energies, viz.: (1) effect of cleavage rate and (2) effect of confining stress level. THEORY Cleavage experiments were conducted on rock samples similar to that illustrated in Fig. 1. Blocks of rock several inches wide, 2- to 3-in. thick, and up to 3 ft in length were grooved longitudinally with shallow guide slots. A crack was initiated and allowed to extend along the web as the top of the rock specimen was pulled (or pushed) apart. Auxiliary equipment permits the measurement of (1) force applied at the top, (2) separation at the top and (3) crack length. (Further experimental details will be given in the next section.) The rock beams created by the crack are considered ton be cantilever beams. The deflection (or separation of the rock beams) at any point is calculated 4,5 by the beam Eq. 1.

Jan 1, 1967

By L. W. Bahney

MANY methods for the determination of gold or silver, or both, in cyanide solutions have been published, which with care in manipulation, and modification in some cases, will give results that are satisfactory. It is possible to classify or group these methods as follows: 1. Evaporating the solution in a porcelain or agate-ware dish containing litharge,1 or in a "boat" made of lead foil. 2. Forming a lead sponge containing the precious metals by means of zinc shavings,2 zinc dust,3 or a piece of aluminum.4 3. Decomposing the cyanide solution with an acid and precipitating the precious metals by the use of one or a combination of some of the following: Copper sulphate,5 sodium sulphite,6 hydrogen sulphide,7 cement copper.8 4. Precipitating the silver by zinc dust held in a Hooch crucible and determination with a standard solution of sulphocyanate.9 5. Electrolysis.10 6. Colorimetry.11

Jan 2, 1915

By P. C. Hodges

WHILE there is very little romance connected with the operation of a stone quarry, yet to those who have participated in the growth and development of a business that has been a pioneer in its field and that FIG. 1.-LOCATION OF PROPERTY OF MARBLE CLIFF QUARRIES COMPANY. has been in continual operation two-thirds of a century there is bound to be a background of experience, which if properly capitalized, brings progress as well as satisfaction in its accomplishment.

Jan 1, 1936

By Dorsey Lyon

I. INTRODUCTION. In presenting, this paper the writers wish to call attention first of all to the fact that the electric furnace was not developed as a competitor of the combustion furnace, but: 1. For the purpose of doing high-temperature work which it is not possible to do in the combustion furnace; and 2. For the treatment of ores from deposits which. are located in regions where fuel is scarce and costly, and where hydro-electric power is comparatively cheap, as is the case in Chili, in Canada, in certain parts of this country and Mexico.. This paper is not presented with the idea of trying to. prove that the electric furnace should replace the reverberatory or the blast furnace as used at present in the smelting of copper ores, but that it may be substituted for their in those localities which are not favorable to them,) and where either of the two following conditions may exist: (a) A district remote from railway transportation. facilities, and where there is a deposit, or deposits, containing sufficient values to warrant their being worked, but which, due to the cost of getting coke in for operating a smelter and of getting ore out to a smelter, have to remain unworked.. And where, on the other hand, there is plenty of water power which call he developed at reasonable cost for the production of electric power, by the use of which for. smelting the ores in an electric furnace, with subsequent Bessermerization if necessary, a concentrated product may be obtained, which can easily stand the necessary transportation charges. (b) Or,. comparatively speaking, the transportation facilities may be all right, but the cost of fuel be too great to permit of the ordinary methods of smelting, whereas,- on the other hand, hydro-electric power can he developed: in the district at a, low cost,, and the ores could be smelted by the electric furnace at a cost. that would make their treatment possible. With these possibilities in mind we have attempted to make a brief comparative study of the problem for the purpose of aiding those interested in the subject, in determining whether it would be possible metallurgically, and feasible commercially; to use the electric furnace-in those localities where, by reason: of excessive fuel costs, the cost, of operating the furnaces for smelting copper-ores. is either excessive or prohibitive. Although the smelting of copper ores in the electric furnace has received considerable attention and more or less experimental work has been done, so far as: we lire: aware there ate no electric furnaces in the United States which are' being worked on copper ores. In Norway, however, trial smeltings of copper ores with an electric furnace of 1,000 h. p. and an estimated producing' capacity of 2,000 tons per annum, have been

Jan 8, 1913

By D. B. RUSHhIORE

I. INTRODUCTION. OF primary importance in mine-installations is the hoist, which has a very direct bearing on the successful operation of a mine. Conditions vary greatly with different mines, and especially in different localities. Such factors as depth, incline, the number of levels, permissible or desirable speeds, conditions of ore, etc., are always more or less special in each case. Veins of ore are never exactly duplicated, and the nature of the ground through which shafts are sunk may considerably modify permissible values. As mining-laws are made by the different States, they necessarily vary somewhat, and, even when not fully observed, they introduce factors which qualify the conditions of hoisting men and ore. The amount of timbering required is often of importance as relating to hoisting-conditions. Methods of loading ore affect the time required, as also does the question of the use of cars or skips. Safety-precautions must be very carefully considered, and the number of men in each mine, the number of compartments, and often the method of removing water from the mine, must. have careful consideration. While a general discussion of the subject. of hoisting is possible, most cases are entirely special, and can be considered only in connection with the peculiar conditions pertaining to that particular installation. The cost of installation of the hoisting-plant may be an appreciable amount, while the cost of raising the ore may be but a small part of the total operating-charge. In many cases, however, the output of the mine is limited by the capacity of the hoist, and the latter thus becomes of the first importance. * Presented also, by mutual agreement, at the meeting of the American Institute of Electrical Engineers, New York, N. Y., Mar. 11, 1910.

May 1, 1910

By B. W. Prof. Frazier

I PROPOSE in this paper to treat of the chimney merely as a heat engine, as one of the devices resorted to in practice for the conversion of heat into mechanical work. For the sake of simplicity and clearness in the discussion, let us consider the subject in its simplest form. Conceive a chamber, heated from without, in free communicatioH at one end with the external atmosphere, and at the other end opening into a vertical chimney. Let the. cross-section of the chamber be so great, relatively to that of the chimney, that we can neglect the actual energy of the air passing through the chamber. We will neglect, also, all passive resistances to the passage of the air. We will assume that the cross-section of the chimney is constant, and that the air in passing through it neither gains nor loses heat. The following symbols will be employed in the discussion : Po = the normal pressure of the atmosphere, which, it is assumed, is the pressure existing at the level of the chamber. Po = 10332.96 kilograms per square meter. P2 = the pressure of the external atmosphere at the top of the chimney. To = the, absolute temperature of melting ice by the centigrade scale. This is assumed to be the temperature of the external air at the level of the chamber. To = 273°. T2 =the absolute temperature of the air as it passes from the chamber to the chimney. T3 =the absolute temperature of the air as it issues from the chimney. to, t2, t3 are the temperatures, as recorded on the centigrade ther¬mometer, corresponding to the absolute temperatures To, T2, T3 re-spectively to = 0° C. In general, t = T- 273. Io, I2, I3, represent the intrinsic energy of the air at the temperatures To, T2, T3 respectively.

Jan 1, 1882

By M. A. Steinberg, J. Wulff, R. Kamm

In a previous paper1 from this laboratory, the development of a lead grid method for exploring the distribution of strain and density within metal powder compacts was described. In that work thin lead foil with rectangular holes cut at regular intervals was inserted with the powder fill, the arrangement pressed and then radiographed to permit measurement of the deformation of the lead grid. Densities at each grid element obtained in this manner were plotted as a function of the die dimensions. From such plots it was found that the densest part of a compact pressed from one side (the top) is at the top outer region and the least dense at the bottom outer region of the specimen. The axial density maximum occurs more often nearer the bottom than at the top. As a result of such exploratory measurements, it appeared reasonable to conclude that variations in density could be attributed in the main to die wall friction. Thus compacts of large diameter appeared relatively uniform in density except where the die fill had been uneven. Finally it was found that lubrication of the finely finished die cavity contributed more to magnitude and uniformity of density within the compact than interparticle lubrication. Since publication of the above results, it was found that circular-hole grids could be more accurately made and, when deformed within the powder, more readily measured and analyzed. Much of the former work was repeated and new results which include the effect of lubrication, compact height, pressure, speed of pressing and vacuum pressing are reported in the present paper. Circular-hole Grids and Analyses OF Radiographs Commercial lead sheet 0.008 in. in thickness was used in all the work reported. The 0.0938-in. diam holes were punched in the sheet on 1/8-in. centers to an accuracy of 0.001 in. The finished grid used contained eight or more holes in a row and from I to 24 rows. The lead sheet was clamped between two pairs of brass strips bolted to a small milling machine table which was itself bolted to a bench in correct position near a vise which held the punch. Travel of the lead grid in two dimensions was controlled by two steel lead screws calibrated in 0.001-in. divisions. A stripper plate was used on the punch to avoid distortion of the lead foil. A high carbon-high chromium (chrocar) one-piece steel die was used throughout the work. The die cavity was 1.125 in. in diam and the clearance between plungers and die wall was 0.001 in. The die was also used for pressing from both ends with two long plungers. Finally, lapping of die and plungers gave a surface whose rms value On an Abbot profilometer was 5 micro-in. The die walls and plungers were, except where otherwise noted, lubricated with a stearic acid suspension in benzene. This was put on in multiple layers and allowed to dry before filling the die.

Jan 1, 1949

By John Wulff, Robert Kamm, M. A. Steinberg

IN a previous paper1 from this laboratory, the development of a lead grid method for exploring the distribution of strain and density within metal powder compacts was described, In that work thin lead foil with rectangular holes cut at regular intervals was inserted with the powder fill, the arrangement pressed and then radiographed to permit measurement of the deformation of the lead grid. Densities at each grid element obtained in this manner were plotted as a function of the die dimensions. From such plots it was, found that the densest part of a compact pressed from one side (the top) is at the top outer region and the least dense at the bottom outer region -of the specimen. The axial density maximum occurs more often nearer the bottom than at the top. As a result of such exploratory measurements, it appeared reasonable to conclude that variations in density could be attributed in the main to die wall friction. Thus compacts of large diameter appeared relatively uniform in density except where the die fill had been uneven. Finally it was found that lubrication of the finely finished die cavity contributed more to magnitude and uniformity of density within the compact than interparticle lubrication. Since publication of the above results, it was found that circular-hole grids could be more accurately made and, when deformed within the powder, more readily measured and analyzed. Much of the former work was repeated and new results which include the effect of lubrication, compact height, pressure, speed of pressing and vacuum pressing are reported in the present paper. CIRCULAR-HOLE GRIDS AND ANALYSES OF RADIOGRAPHS Commercial lead sheet 0.008 in. in thickness was used in all the work reported. The 0.0938-in. diam holes were punched in the sheet on 1/8-in, centers to an accuracy of 0.001 in. The finished grid used contained eight or more holes in a row and from I to 24 rows. The lead sheet was clamped between two pairs of brass strips bolted to a small milling machine table which was itself bolted to a bench in correct position near a vise which held the punch. Travel of the lead grid in two dimensions was controlled by two steel lead screws calibrated in 0.001-in. divisions. A stripper plate was used on the punch to avoid distortion of the lead foil. A high carbon-high chromium (chrocar) one-piece steel die was used throughout the work. The die cavity was 1,125 in. in diam and the clearance between plungers and die wall was 0.001 in, The die was also used for pressing from both ends with two long plungers. Finally, lapping of die and plungers gave a surface whose rms value on an Abbot profilometer was 5 micro-in. The die walls and plungers were, except where otherwise noted, lubricated with a stearic acid suspension in benzene. This was put on in multiple layers and allowed to dry before filling the die.

Jan 1, 1948

By John G. Tate, George W. Nicolson, James L. Bruce

FOR more than 25 years modern mining has been carried on in the Island of Cyprus, Mediterranean Sea, by the Cyprus Mines Corp. of Los Angeles, Calif. The general features of these operations have been described.1 From 1935 to June 30, 1940, top slicing in the Mavrovouni mine produced in excess of 2,000,000 long tons. The rate for the last part of this period was approximately 50,000 tons per month. DESCRIPTION OF ORE BODIES The shape of the ore body now being top sliced in the Mavrovouni mine is an inclined irregular pyritic pipe or chimney of large dimensions, extending from unknown depths below the bottom level at elevation 250 ft below sea level, to the highest level at elevation 400 ft above sea level. The present surface above the ore body lies between 550 and 650 ft elevation. Undoubtedly the ore body extended to surface and was mined by the ancients by opencast and underground methods. The old pits were gradually filled up by erosion until now they show as slight depressions in the topography. The largest area of the ore body is at elevation 170 ft below sea level, where the horizontal section is almost elliptical, with a width of 600 ft and a length of 1000 ft. Below this elevation the shape of the ore body continues to be elliptical but with reduced dimensions. Above this elevation it rises flatly towards the south with a substantial depression in the upperside of the chimney and irregular ridges or wings rising on each side. It gradually grows smaller as it rises. The ore body is a pyritic replacement of andesitic extrusives which occur as flows and pillow lavas. With the exception of the upper portions of one or two small offshoots rising from the main ore body, all ore is completely surrounded by andesite. Most of the andesite lying above the ore body is covered by marl and clay sedimentaries of Miocene and later age. The Miocene is presumed to be older than the ore mineralization. That portion of the andesites which lies between the sedimentaries and the ore body has been broken by slumpage, and weathered, and iron-stained by the descending meteoric waters. It is a mass of crushed material that caves and follows downward readily as the top-slice stopes retreat. The main ore body is a heavy cupreous pyrites mass assaying on the average about 4.0 pct Cu; 48.0, S; and 42.0, Fe. In places the copper drops below 1.0 pct. On the borders of this heavy sulphide ore body lie disseminated cupreous pyrites ore deposits of large dimensions. Some portions of these appear to be closely related to the heavy sulphide ore, as the ratio of copper to pyrite is about the same. The greater part of the disseminated ore, most of which lies immediately to the east of the main ore body, contains less than 0.10 pct Cu and about 25.0 to 30.0 pct S. This probably can

Jan 1, 1947

By Henry S. Washington

Introduction. It Still Rains On The Choco ! I Well Remember One Evening A Dozen Years Ago, While. Traveling Toward The Town Of Negua In A Small Champa Or Dug-Out Canoe, The Rain Fell So Heavily That I Had To Work My Hardest To Bail Out The Water With A Large Totuma Or Gourd In Order To Keep The Canoe Afloat, The Senegambian Meanwhile Plying His Paddle In The Stern. If Any One Thinks Bailing Is Easy Work, Let Him Scoop Out A Quart Or More At A Stroke, 40 Times A Minute For Half An Hour, And I Venture That He Will Change His Opinion. These Small Canoes Required Only One Paddler, To Make The 3 Miles An Hour Which Is The Standard Rate Of Aquatic Progress On The Choco. Another Time, On The Atrato River, About Six O'clock In The Afternoon, The Rain Fell So Heavily Than An Empty Gourd, 9 In. In Diameter And 4.5 Deep, Was Filled To The Brim In 90 Sec., Timed By A Watch. Such Downpours Are Typical, But Unless Caught In One It Is Not Specially Noticed. These Downpours Seldom Last More Than An Hour, And Frequently Cover Only A Limited Area, Occasionally Falling On One Bank Of A River And Not On The Other. During The Night-Time,' The Rain, If Gentle, Will Usually Last Until Dawn, And Sometimes An Intermittent Drizzle Will Keep Up All Day As Well, Although, As A Rule, It Rarely Rains During The Day. The Rise Of The Rivers, Due To The Rain-Fall, Varies From A Few Inches To Several Feet. One Night In August, 1899, The Spuds Of The Dredge Margaret, Operating On The Atrato River, Showed A, Rise Of 16 Ft., And For 3 Days Thereafter Occurred The Greatest Flood Known In That District For 32 Years. The Dredge Had All Three Spuds Clown, And The 2-Yd. Shovel Dragging On The Bottom. A 0.75-In. Cable Fast To A Stout Tree, 700 Ft. Away, Stretched Tight

Sep 1, 1908

By S. F. Radtke

The properties and characteristics of lead and zinc have made these metals useful to man in many ways since the days of antiquity. Despite their long history of use, however, these metals have proved to be extremely resilient and responsive to modern needs. New alloys and compounds continue to be developed, adding to the growth of these metals. Consumption data is given for 1969 and compared with one and two decades ago. Trends in major markets also are cited and explained. Uses for lead and zinc which have come into prominence within the past few years are described and explained, with emphasis on the role played by the industry's cooperative research program. Current efforts in the research phase are discussed, with details given on major efforts for both metals, including new alloys, process developments, applications research, finishes, coating, paints and pigments, batteries and fundamental research. A forecast is given of promising new areas and a projection made on a longer term of new applications that may emerge from current research.

Jan 1, 1970

By A. Timur

Fluid flow properties of porous media have long been of interest in such varied disciplines as geology, geophysics, soil mechanics, and chemical, civil, and mechanical engineering. This interest has resulted in numerous models of porous media that have been proposed, tested, and found to be useful under, at best, only special circumstances. A critical review of most of these models is given by Scheidegger. 1 The application of each new tool to the study of porous media has helped to test some of the existing theories and to form new ideas based on the new parameters being measured. In the application of nuclear magnetic resonance (NMR) techniques to the study of the properties of fluids in porous media, the theoretical studies of Korringa et al.2 resulted in a model for the relaxation of spin polarization of protons in a hydrogenous fluid in a pore of a solid. Seevers3,4 verified this model, established a method for measuring the surface-to-volume-ratio distribution in a porous medium, and proposed a technique for determining specific permeability in sandstones. In the present investigation, the uses of NMR methods are extended and a simple model of porous media is developed from an analysis of pulsed NMR measurements. In this model, the pore spaces of a porous medium are divided into three groups on the basis of their surface-to-volume ratios. To evaluate predictions of the NMR model, laboratory measurements of spin-lattice relaxation time, porosity, permeability, and residual (irreducible) water saturation were conducted on more than 150 sandstone samples obtained from four oil fields in North America. Applications are discussed for estimating the volume of movable fluid, ?p, and the specific permeability, k, of sandstone samples. The former parameter, which can be considered as producible porosity, is expressed by ?p = [1 -- (Swr/100)]? , .... (1) where + is porosity in percent of bulk volume and Swr is the residual (irreducible) water saturation in percent of pore volume at a capillary pressure of 50 Psi. Fast, nondestructive laboratory methods are described for determining porosity, movable fluid, and permeability of sandstone samples from measurements with a pulsed NMR (spin-echo) apparatus. Procedures are given for adapting these methods to samples of irregular shape and small size. Theory General In the Korringa, Seevers, and Torrey2 (KST) model the observed decrease in the spin-lattice relaxation time, T1, of protons of a hydrogenous liquid contained in the pore spaces of a porous solid is attributed to an increase in the correlation time for the random motion of the water molecules and to the presence of paramagnetic centers at the liquid-solid interface. This KST model predicts the observed relaxation time of a hydrogenous liquid in a pore of a solid through

Jan 1, 1970

By T. L. Johnston

MUCH has been said and written about deep mine shafts and deep drill holes as man in his search for mineral wealth digs deeper into the earth's crust. Each year some new extra depth is heralded as a record, but with unlimited possibilities of going still deeper. In contrast to "digging deep," "mining high" is limited by the height of the mountains (Mt. Everest being the maximum with its 29,000-ft. elevation) and also by the extent of human endurance. An ex- ample of what might be called near- stratosphere mining in what is probably the highest mine worked by compressed air in the world is seen in a recent project in the Andes mountains of southwestern Bolivia.

Jan 1, 1939

By Robert R. Brookshire

Brush plating has been thought of by many as black magic bordering on alchemy. Actually it is a science that uses both electro-chemical and mechanical engineering skills and technology. We are not sure when brush plating was first used or by whom. I do know that many times when we would put in for patents on things we thought of as new and innovative, we would find that someone had done it many years before. It took World War I1 to get brush plating off and running. Now at this point, someone may be asking just what is brush plating? And why are we plating brushes? One way of describing what brush plating is, is by telling what it is not such as tankless plating. Brush plating-is an electro deposition of an electro-platable element or alloy onto a conductive surface. To do this a source of direct current is required; this can vary widely. I prefer stepless voltage control from 0-35 volts with a capacity depending on the size job to be done. This can vary up to 500 amps for normal applications. In one case we have used 7500 amps.. In the beginning a brush was actually used with a wire in the middle of the bristles and a jelly-like paste made up from tank plating solutions. The bristles were saturated with the gunk and the spot to be plated was muddled with the concoction at a potential which was the same as the applied tank Voltage. Metal was deposited but only thin coats were achieved. Today we use graphite wrapped or covered with cotton to form a Q-tip type anode. By using graphite rather than a specific metal we are able to either plate, de-plate or strip, electro- mill, electropolish, or anodize--all with the same equipment. Only the electrolyte needs to be changed.

Jan 1, 1984

By K. Reinhardt

THE idea of burning blast-furnace gases directly in gas-engines, instead of under steam-boilers, as had previously been done, was first put into practice barely ten years ago, almost simultaneously in Great Britain, Germany and Belgium. The pioneers of this movement made their first experiments with small engines. After these experiments had given satisfactory results, and it had been shown that the thermal value of the poor blast-furnace gases, in spite of defective scrubbing, could with safety be directly transformed into mechanical work in the gas-engine, there very soon arose a considerable demand for gas-engines of large power, similar to the large steam-engines employed in metallurgical works. In face of these sudden requirements, the gas-engine builders were placed in a difficult position; for up to that time the gas-motor was considered as suitable for small engines only, and it was generally believed that the limit of size bad been attained with 100 to 150 effective h.p. in a single cylinder. Manufacturers of gas-motors, however, did not underrate the advantages offered by this new field for their manufactures, and it so happened that in Germany the Berlin-Anhaltische Maschinenbau-Gesellschaft, of Dessau, was the first to undertake the construction of a 600-h.p. two-cycle gas-engine, with two cyl¬inders of the Oechelhäuser-Junkers type, for the Hoerder Mining & Smelting Company. The engine was started in 1898, and, with a few improvements and alterations, is still working satisfactorily. This engine worked with astonishingly high of efficiency, considering the period. The builders were therefore

Nov 1, 1906

By James M. Link

Slurry transport of industrial minerals has proven to be practical, economical, and efficient. Industrial minerals currently being pumped for long distances include cement, clay, phosphate, sand, and various waste product from industrial mineral processing operations. This paper will touch upon the basic theory of hydraulic transport of solids and then consider the economic and engineering considerations upon which construction and operation of such a line would be based. Where possible, actual cost data will be presented.

Jan 1, 1974

By D. F. Hewett

CONTENTS PAGE Introduction 1 Geologic features of eastern Oregon 2 Geology of the Sumpter quadrangle 2 Rocks older than the ore deposits 3 Rocks younger than the ore deposits 8 Lodes of the Sumpter quadrangle 8 Areal distribution 8 Geologic distribution 9 Major features of the veins 9 Mineralogy and texture of the veins 13 Ore deposits zonally disposed around the Bald Mountain batholith . . . . 13 Summary of mineralogy and texture 32 Zonal relations 33 Ore deposits zonally disposed around Greenhorn Mountain batholith . . . 36 Zonal relations 37 Relation of textural features to zonal arrangement of veins 37 Summary of zonal relations 38 Comparison with similar districts 39 Outlook for the district 40 INTRODUCTION IN an earlier report on the Sumpter quadrangle1 it was briefly stated that the quartz lodes of that region might be separated into several groups or belts on the basis of the kind and abundance of the minerals of which they are composed, and that these belts were disposed as areal zones around the principal intrusive mass of the region. When the opportunity to revisit the region was offered in 1929, as a result of a cooperative agreement between the State Mining Board of Oregon and the United States Geological Survey, it seemed advisable to pay particular attention to this feature of the lodes, in the hope that if the idea of zonal relations was confirmed it might serve as a guide in exploitation.

Jan 1, 1931

By Francis Foley

INTRODUCTION DURING the summer of 1919, the late Dr. Henry M. Howe, then Chairman of the Division of Engineering of the National Research Council, organized a committee to obtain a better insight into the behavior of carbon steels under the influence of various treatments by a proper control of the time and temperature factors. During part of 1919 and 1920, work in connection with this investigation was carried on at Dr: Howe's laboratory at Bedford Hills, N. Y. During 1921 there was an enforced hiatus in the work, occasioned by the illness which resulted in Dr. Howe's death in 1922. At that time one of the present authors compiled the results of the work which had been done and this was published in 1923.1 Following the publication of this work, it seemed desirable to carry on in the same manner an investigation of steel of C 0.75 per cent., which steel had not been as fully treated as had the other steels of C 0.34 and 0.52 per cent., used in the published work. Furthermore, certain unusual results have been obtained in the treatment of C 0.52 per cent. steel by quenching and drawing, and repetition of this part of the work seemed advisable. This has been done during the past year at the School of Mines and Metallurgy of the University of Missouri at Rolla, Mo., by a cooperative undertaking of the School and the Bureau of Mines, working in conjunction with the Committee on Heat Treatment of Carbon Steels of the National Research Council. The present paper is a report of the results obtained in this work.

Jan 2, 1926

By ERNEST F. . SURCEIARD

work have been published from time to time by the Survey.' A detailed report on the Birmingham district, with maps, has been completed, and will be published within the next year." In the following paper it is aimed to present only an outline of the geologic relations of the ores, since the Appalachian geology of Alabama has been discussed by many previous writers, but to describe rather fully the ore of the Birmingham district, and to discuss its relations and probable extent. IT. OUTLINE OF THE GEOLOGY. 1. Stratigraphy. The pre-Pennsylvanians rocks exposed in and along the borders of the valley-regions of Alabama, range from middle Cambrian to Mississippian (Lower Carboniferous), and at the SW. extremities of the valleys these rocks are overlain by coastal-plain deposits of Cretaceous and Tertiary age. A generalized section of the pre-Pennsylvanian Paleozoic rocks for the valley-regions is given in Table I. TABLE I.-Section of Pre-Pennsylvanian Paleozoic Rocks in Valley-Regions of Alabama. System. Formation and character. Thickness. Ft. Shale and sandstone 300 to 2,200 Carboniferous (Mississippian- Limestone and shale 300 to 800) I Sandstone and shale 50 to 200 1 Fort Payne chert and limestone 100 to 300 Devonian Chattanooga shale 0 to 30 Silurian Clinton (" Rockwood ") shale, sand¬ stone, and iron-ore 200 to 700 Ordovician Chickamauga ("Trenton") limestone.. 200 to 800 Cambro-Ordovician Knox dolomite and chert 1 2,200 to 2,700 basal dolomite 500 to 600 Cambrian Conasauga shale and limestone 1,000" to 1,500 - I a Base not. exposed.

Nov 1, 1908

By E. C. Olsen

This paper describes the unusual hazardous conditions encountered in mining thick, inclined coal beds under heavy cover in Carbon County, Utah. This description includes heavy roof conditions, sloughing ribs, steep pitches, and severe bouncing experience. Emphasis is placed on the top bench system of mining and development in the top half of a 16-ft seam, under the roof rock, which is bolted, and the recovery of the bottom coal on retreat; success of bolted roof and ribs; and shuttle car haulage on pitches up to 25%. The use of protective cages for operators of face equipment, the guarding of belt conveyor systems to prevent injury associated with deliberate entry, and the positive lockout of electrical equipment is described and illustrated. Most coal mining areas of the Western United States are characterized either by thick beds, steep pitches or heavy cover. Individually, each of these may present inherent safety hazards that in- fluence mining. When all are met at one location, the combined effect is to make the safe operation of the mining property a challenge to management. These combined conditions are met in the coal mines of the Columbia-Geneva Steel Div. of the United States Steel Corp., in southeastern Utah. This coal bed measures up to 16 ft in thickness, the pitch is as much as 25% and mining is under a cover approaching 3000 ft. The Sunnyside coal bed is found in the Book Cliff Mountains, a great escarpment extending from west of Castle Gate, Utah, some 180 miles to Grand Junction, Colo. West of Green River, Utah, the Book Cliffs swing sharply to the north because of the domelike uplift of the San Rafael Swell to the southwest. It is in this northerly extension of the Book Cliffs that the Sunnyside coal in the Blackhawk Formation of the Mesa Verde Group, Upper Cretaceous Age is found. The strata are transected by numerous faults with from a few inches to as much as a hundred feet of displacement. All of these faults have had some effect on the mining operation, either in roof control or, in the case of major faulting, the pattern of mine development. MINING PRACTICES Mining has generally been confined to the Lower Sunnyside Seam which measures from 7 to 16 ft in

Jan 1, 1963