Search Documents

By G. P. de Forest, G. O. Hiers

The object of the experiments reported in this paper is to determine the eutectic composition of copper and tin and to determine the location of the part of the liquidus line immediately above the eutectic composition in copper. Three methods were used in the investigation: (1) the method of dissolving copper in a bath of molten tin at constant temperature, with the idea that when the bath was saturated with copper its copper content, by analysis, together with the temperature at which the saturation took place would locate a point on the liquidus line; (2) the method of the differential cooling curves, and (3) the method of microscopic examination. This paper is principally concerned with the results of the last two methods mentioned. The results of the first method, that of dissolving copper in molten tin, did not agree with the results of Miller,' by the same method, nor with the results of other investigators by other methods, nor yet with the results of the cooling-curve experiments and microscopic examination reported here. Solution of Copper in Molten Tin To determine the amount of copper that would be dissolved by molten tin at a given constant temperature the apparatus shown in Fig. 1 was used. It consists of a cast-iron pot a, 6 in. deep and 8 in. dia., well cleaned inside and dressed with graphite. This pot, which holds 15 lb. of tin, g, rests on a hot plate b with resistance winding c. The thermocouple d leads to a Wilson-Maeulen temperature regulator for maintaining the temperahre at the heating coils at a fixed temperature to within ±5°C. There is a shallow bath of solder e on the top of the hot plate to improve the thermal contact between the plate and the pot. An insulating jacket f of asbestos prevents the irregular radiation of heat from the apparatus. The copper stirrer h slowly rotates in, and is dissolved by the bath of molten tin g. This bath is protected from excessive oxidation by a layer of charcoal j. The stirrer h is fixed to the lower end of the iron tube k, which is so mounted that it can be driven by a motor with reducing gear. The temperature of the bath is indicated

Jan 1, 1930

By A. S. Callen

These iron mines of Spain are located on the mountain ridge forming the boundary between the Teruel and Guadalajara provinces, called Sierra Menera. They form a property of 25 mines extending over an area of 1,677 hectares (4,140 acres) situated at a height varying from 1,200 m. (3,940 ft.) to 1,500 m. (4,920 ft.) above sea level. The deposit follows the direction north to south; huge masses of ore are being found both on the slopes and at the summit of the Sierra. The ore occurs among quartzites and magnesite limestone, in some places overlaid by quartzite 15 m. (50 ft.) thick; in some others (and this is more general) the ore is overlaid by earth and boulders of quartzite origin; this layer is about 8 m. (26 ft.) thick. The ore beds occupy the geological horizon of the Superior Trias or Muschelkask, which are here in direct contact with the Silurian quartzites. The lime-stones have been more or less transformed. There is ample evidence to show that these mines were worked in very ancient times—objects and tools employed in mining by the ancient Romans and Arabs are to be found plentifully in old workinigs which extend down into the deposits. It has been estimated that more than 10,000,000 tons of ore were mined in the old days in this district and carried to the primitive forges in the vicinity where iron of much renown in Spain was extracted. Remains of more than 20 of these forges are found in the neighborhood of Sierra Menera and are usually situated near waterfalls and forests. Much investigation has been carried on for the purpose of determining the quantity of ore to be found in these mines, but no exact calculations can be made at present. When the investigation is completed it will surely be found that the deposit contains a much larger quantity than the 100,000,000 tons indicated by the present workings. The mines are now worked as open quarries and this method can and will be followed for a long time, probably until the deposit is worked out. Figs. 1 and 2 give some idea of the quarries in operation and the reserves, the iron-ore stocks, screening installation and general arrangement. From these quarries 1,000,000 tons can be mined annually (987,000

Jan 1, 1916

By T. C. Russell

The Conda phosphate mine, eight miles north of Soda Springs in Caribou County, Idaho, was opened up by the Anaconda Copper Mining CO. in 1920. Except for brief periods, during the 20's and early 30's, the mine has maintained a continuous production, and 2,100,000 short tons of phosphate rock have been shipped to the company's phosphate fertilizer manufacturing plant at Anaconda, Mont., or to independent processing plants on the Pacific Coast; a small tonnage of the rock has been shipped to the Hawaiian Islands. The Phosphoria formation on the Conda property consists of two, commercial-grade phosphate beds separated by 147 ft of black to brownish colored phosphatic calcareous shales interbedded with softer mudstones, clays, and occasional narrow seams of oolitic phosphate. The main lower phosphate bed in the series averaging 7.1 ft in thickness, is called the "foot-wall bed," which lies coriformably on the Wells limestone formation, the 1atter often containing irregular bands of chert. The upper or " hanging-wall bed" of phosphate rock averaging 7.2 ft in thickness, is overlaid by thick quartzite beds, locally called the " Rex chert" member in the upper portion of the Phosphoria formation. (Fig 1.) There are two anticlines on the property with axis striking approximately parallel to the mountain range beneath which extensive development on phosphate rock has been conducted in the past, and is now in progress. The phosphate beds have been eroded to a large extent from the tops of these anticlines, leaving at least three well-pronounced outcrops of the phosphate beds exposed within the boundaries of the Anaconda Copper Mining Cornpany's properties. At present, mining operations in the Conda No. 3 mine are confined to the two phosphate beds along the east flank of the easternmost anticline, where the dips on the beds vary from 50° to 60° east, thereby affording favorable conditions for the sublevel mining system now in use. Mining operations formerly were confined to the footwall or lower oolitic phosphate bed because of its higher phosphate and vanadium contents (32 pct P²O5 and 0.29 pct V2 O 5); this bed averages 7.1 ft in thickness. The oolitic portions of the upper bed were of satisfactory grade, but the shale and clay partings (Fig 2) diluted the mined rock and could not he separated economically by selective mining or by sorting. Experiments in beneficiating this rock were carried on for a number of years. Recently, a simple washing process was adopted, which gave a satisfactory grade of concentrates and a high recovery of P² O5. In 1947 it was decided to expand Anaconda's production of treble superphosphate and phosphoric acid by approximately 90 pct. This rock will be obtained from the footwall and hanging-wall beds, and the rock from the hanging-wall bed will be benefici-ated at -Anaconda.l In order to take advantage of the previous development on the 500 secondary haulage level, short crosscuts will be driven at approximately 950 ft intervals from the existing lateral drifts through the hanging-wall shale beds. From the inner end of each crosscut, short lateral drifts will he driven in both directions, so that four working raises can he put up on the dip of the phosphate bed at proper intervals along each of the lateral drifts. The mining operation on the footwall bed at Conda

Jan 1, 1950

By S. R. Zimmerley, John Gross

The method of measurement of surface on quartz particles was given in a previous paper.' With such a method the relation of surface produced in crushing quartz can be compared to the work in crushing without recourse to sieve sizing or microscopic measurement. In crushing, the work input must be known with a fair degree of accuracy. With crushers, rolls, ball mills, and similar apparatus the measurement of the work in crushing is subject to possible errors, due to friction in the transmission as well as in the machine itself. Moreover, relatively large quantities of material must be crushed to get an average figure. In the selection of a method of crushing, simplicity in design and operation was desired and this was most readily obtained by the use of a free-falling body. A description of the apparatus embodying this principle is given herewith. The Crushing Device The apparatus used is shown in Fig. 1 and in cross-section in Fig. 2. The material to be crushed is placed in the crushing chamber C in the steel mortar M. The mortar is 3 in. dia. by 3 in. high. Two mortars are used, one having a crushing chamber 1 in. dia. by 36 in. deep, with a capacity of 4 g. of quartz, the other having a crushing chamber 1 1/2-in. dia. by % in. deep, with a capacity of 12 g. of quartz. The position of the mortar is adjusted by means of three centering screws A. The steel plunger P, which fits neatly into the chamber, is placed on top of the material to be crushed. Plungers of different lengths were tried and as they were found to give practically identical results the length adopted was equal to the depth of -the chamber. The mortar rests on a solid steel base B but is separated therefrom

Jan 1, 1930

By AIME AIME

Annual net production of crude oil from the Anglo-Iranian, Oil Company's fields in Iran for the years 1940 through 1945 amounted to: YEAR TOTAL PRODUCTION (Long Tons) 1940 8,626,639 1941 6,605,320 1942 9,399,231 1943 9,705,769 1944 13,274,243 1945 16,835,000 (preliminary figure) All developed fields were on almost continuous production throughout the war, though their operation naturally was hampered by war conditions, which affected particularly supplies of equipment.

Jan 1, 1946

By B. H. Bergstrom

The Gaudin-Meloy1 size distribution equation requires the evaluation of two constants, xo and r. The common log-log representation of a screen analysis as cumulative weight percentage passing versus size, readily yields the required constants as illustrated for curves A and B in Fig. 1. The 100% passing (y = 1.0) size is simply x,. If the straight portion of the curve be extrapolated to the 100% passing (y=1.0) abscissa, the intercept is the Schuhmann size modulus, k. The ratio of xo to the size modulus, k, is r as shown: The Gaudin-Meloy equation requires that the slope, a, of the size distribution approach unity in the finer sizes, as is the case for curves A and B. Often distributions are better characterized by slopes other than unity. The schuhmann2 equation is able to represent these distributions if the upper portions of the curves are ignored. Empirically, the Gaudin-Meloy equation can be modified to yield slopes other than unity by writing it as Here, a is the familiar Schuhmann slope, and xo is the 100% passing size. The value of r is still given by Eq. 2. Eq. 4 with its easily determined constants is more versatile than either the Schuhmann or the Gaudin-Meloy equations, since a wide variety of size distributions can be closely described. It is easier to fit than the Rosin-Rammler3 equation, and has the advantage that the top size, x,, is finite. REFERENCES A. M. Gaudin and T. P. Meloy: Model and a Comminution Distribution Equation for Single Fracture, AIME Transactions, 1962, Vol. 223, pp. 40 to 43. R. Schumann, Jr.: principles of comminution, I., size Distribution and Surface Calculations, AIME Technical Publication No. 1187, 1940. P. Rosin and E. Rammler: The Laws coverning the Fineness of Powdered Coal, J. Inst. Fuel, 1933. Vol. 7, p. 29.

Jan 1, 1967

By Robert T. Ault

The nature of fracture in unnotched tensile and notched tensile sheet and round specimens and V -notched and precracked Charpy-type sheet specimens of both wrought stress -relieved and re-crystallized molybdenum was investigated over the temperature range of -78° to 300°C. The sharp rise in fracture stress, for unnotched tensile samples, as the temperature is increased above the brittleness transition temperature (Tb), is found to be a result of an increase in flow stress due to plastic constraint and an increased strain rate which results from the onset of necking at Tb . Quasi-brittle fracture in notched tensile samples is found to occur when the tensile stress at the elastic-plastic interface, beneath the root of the notch, reaches a maximum critical value, which is independent of test temperature over the range from —78° to 25°C, but dependent on microstructure. In the temperature range between 150° and 300°C, unnotched tensile and notched tensile samples alike are found to fracture by a ductile fibrous tearing process which is discontinuous in nature, as a result of the competition between the processes of tearing, through continued plastic flow, and local work hardening. Results from the V-notched and fatigue-cracked Charpy-type impact tests demonstrate that crack initiation is the governing factor in the low-temperature (-78° to 25°C) fracture process for molybdenum. In recent years, there has been considerable interest, and a commensurate number of investigations, concerning the duc tile-to-brittle transition in refractory metals. There has not developed, however, a satisfactory explanation for the uniaxial tensile fracture-stress transition which accompanies the well-known ductility transition. This matter therefore warranted investigation. In a similar manner, the increased importance of notched tensile strength values in evaluating materials and in design criteria requires a better understanding of the factors which control the fracture behavior of notched tensile samples. In a previous investigation1 of the nature of initial yielding and fracture in notched sheet molybdenum at room temperature, it was suggested that plastic constraint was the controlling factor in governing the fracture behavior of notched samples. The final portion of this investigation was concerned with the fracture toughness of molybdenum. Of particular interest was the comparison of effective surface energies for fracture in V-notched samples with fatigue-cracked, Charpy-type samples in order to ascertain the relative importance of the initiation and propagation phases of the fracture process. MATERIALS AND TEST PROCEDURE Sheet tensile, notched tensile, and V-notched Charpy specimens were prepared from 50-mil, stress-relieved molybdenum sheet.* Half of these specimens were vacuum-annealed for 1 hr at 1200°C and 7.5 x l0-5 Torr and furnace-cooled to produce a relatively uniform grain size of 0.30 mm diameter. Round notched and unnotched tensile specimens were prepared from warm-rolled and swaged 5/8-in.-diam bar.* These specimens were vacuum-annealed for 1 hr at 1350°C and 5 x lom5 Torr and furnace-cooled to produce a grain diameter of 0.11 mm. Material analyses in ppm were: C N O H Sheet 290 10 4 1 Bar 50 30 30 2 The unnotched tensile sheet specimens had a 1/4-in. gage width and a 1-in. gage length. The unnotched tensile round specimens had a 9/32-in. gage diameter and a 1-1/4-in. gage length. The sheet and round notch tensile specimens are shown in Fig. 1. All of the notched tensile specimens tested were tandem-notched in order to study the location and mode of fracture initiation. The tandem-notched specimens were carefully machined so that the largest variation in notch depth on a single specimen was 0.001 in. Thus, when fracture occurs, the extent of plastic deformation that exists in the un-fractured notch section is that which exists just prior to fracture. All of the tandem-notched sheet specimens were electrolytic ally polished and chemically etched prior to testing. The V-notched Charpy-type specimens machined from the 50-mil sheet material had the standard dimensions of 2.125 in. long, 0.394 in. deep, and a 0.010-in. root radius. The unnotched tensile and notched tensile tests were conducted over the temperature range of -78° to 300°C, in a 10,000-lb Instron Universal Testing Machine, at a constant crosshead speed of 0.020 in. per min. The V-notched Charpy-type

Jan 1, 1964

By W. H. Blauvelt

THE subject of fuel-briquetting has attracted much attention on the part of engineers and investors for the past 15 or 20 years, and especially in recent years, during which a number of plants have been built, with more or less commercial and technical success. Our technical literature contains numerous descriptions of certain processes, and discussions of the industry in general. For a history of the development of the art in the United States, and for descriptions of many of the processes which have been tried, reference may be made to the files of our Transactions, and, for more recent information, to a paper by C. T. Malcolmson, read before the First Annual Convention of the International Railway Fuel Association in June, 1909. The purpose of the present paper is to describe the briquette-plant of the Solvay Process Co. and the Semet-Solvay Co. at Detroit, Mich., which, after a period of long and costly evolution, is now operating satisfactorily on a commercial basis. I believe that it will be of interest to some of our members to have the details of operation, lower-consumption, labor, etc., as worked out on a practical and commercial scale in a going operation. The briquette industry has had a somewhat checkered career in the United States, and much the larger portion of the failures has been due entirely to commercial causes. It seems axiomatic to say that before undertaking the installation of a plant for manufacturing briquettes it is necessary that the local situation should be carefully examined : First, to determine the kind of briquettes, if any, the local market will consume; that is-to say, whether the available fuel-supply is such that briquettes would be a welcome addition, and whether the most promising field is the industrial or the domestic market. Second, if there is an available supply of raw material, as coal,

Mar 1, 1910

By Arthur Bell

(San Francisco Meeting, September, 1915) . PRIOR to 1908 the oil production in the State of California, had been almost entirely a heavy fuel, oil, with a high flash point, hut changed within a-short period to a large percentage of refining oil with a low flash, by reason of the coming in of the Santa Maria field, the Midway field, and the increased production of the Fullerton field. This is clearly shown in the following tabulation of California's production: Year Barrels . Below -20° Be, Above 20° Be,, Per Cent_ Per Cent. 1905 48,307,000 90 10 1910 77,698,000 SO 20 1912 90,075,000 6o 31 1914 10:3,600,000 47 53 The bringing in of these high percentage's of light oil with their dangerous low flash and the increasing demand for the refined products necessitated the devising of some cheap and efficient means of quickly separating the lighter elements either in the field or at the main distributing points; also it became necessary to remove the excessive percentage of water which many of the light oils carried in emulsion.

Jan 9, 1915

Discussion of the paper of R. H: Sweetser,. presented at the Cleveland meeting, October, 1912, and printed in Bulletin No. 71, November, 1912 pp. 1327 to 1334. See also Bulletin 11 No. 72, December, 1912, pp. 1561, 1562. J. J. HOWARD, Dover, N. J. (communication to the Secretary*) :-No doubt there are as many different methods of starting a blast-furnace as there are men who assume that responsibility. Having blown-in a furnace a few years ago in a manner similar to that outlined by Mr. Sweetser, things went along so well at the start that I had time for a little reflection on what was going on inside the furnace. I saw the wood turned to charcoal practically, and it occurred to me, why should I use wood when I could put in the charcoal in the. first place, and thus save a lot of time, and also eliminate the dangerous gas from the wood, which is the cause of most of the accidents in starting up a furnace. I had a furnace out for repairs and decided to use no cord-wood in blowing in. I put in about a carload of charcoal and used no wood except some shavings and oily waste at each of the tuyeres. The furnace had 16 tuyeres and was 100 by 22 by 14.5 ft. Hot rods were put in each tuyere' and the blast started immediately at 11 a.m. Within 5 mill. the air was all driven out of the stack and the gas lighted of its own. accord at the top of the furnace. It was allowed to burn for 5 min. longer and then the bell was closed and the gas taken to the last stove and the last boiler on the gas-main. It was all clone so quietly that it was hard to realize that the gas was down. The tuyeres were as bright as if the furnace had been in blast for a long time. I have learned since that others have used the same method, but they had not passed the good advice along.

Jan 5, 1913

By T. W. Turk, S. A. Sass

The engineering design features of the Mercur Gold Project crushing, grinding, carbon-in-leach, bullion, reagent, and tailings disposal areas will be discussed in this paper. It presents a project overview and flowsheet along with selected design alternatives. During the engineering phase, major equipment and other features were selected to optimize design within site location and environmental constraints. The project team organization and procedures were adopted to accommodate multiple optimization studies while maintaining a tight engineering schedule.

Jan 1, 1985

By R. W. Smith

IN the manufacture of portland cement, the basic and fundamental essential is a limestone uniformly rich in calcium carbonate and carrying less than 3 per cent magnesium carbonate. In searching for such a deposit, also having in mind quantity of rock, accessibility and quarrying facilities, the Pacific Coast Cement Co. discovered and developed its present quarry at View Cove on the east coast of Dall Island, Alaska. Dall Island is about 100 miles west of Ketchikan and 650 miles north from Seattle. It is 70 miles in length and 5 to 10 miles in width. The climatic conditions are much more favorable than would be expected. The temperature ranges from zero to 70 degrees. The precipitation is considerably more than at Seattle, although there was less snow during the last season than at Seattle. The island is rugged and mountainous; the vegetation is moss and grass and a large portion is timbered with spruce, hemlock and cedar. Some of this timber has market value. The limestone quarry is about 30 miles north of the extreme southern end of the island. The company acquired 240 acres which contain limestone of remarkable uniformity, the percentage of calcium carbonate being about 95. It is estimated that there is ample recover- able rock on the holdings to supply the cement plant at its maximum capacity for well over 100 years.

Jan 1, 1929

By J. Chupak, D. J. Salley, G. L. Simard

Radiotracers were demonstrated to be of considerable value in a study of the interaction of dithiophosphate with galena. The interaction had characteristics of both chemisorption and chemical reaction, being complex because of the nature of the galena surface. Sorption was rapid and markedly reversible, and flotation occurred at relatively small amounts of dithiophosphate sorbed.

Jan 1, 1950

By John D. Price

R. W. Campbell (Jones and Laughlin Steel Carp., Pittsburgh)—As usual John Price has presented an excellent paper. I know of no one who has devoted more time and conscientious thought to this subject than he has, and his efforts have produced scientific data and conclusions of real value. Results of similar studies made by the Jones and Laughlin Steel Corp. on the blending of Pennsylvania coals may be of interest. During 1935 the late F. W. Wagner and the present writer developed an empirical physical fuel value formula for evaluating the combined physical tests of metallurgical coke, see Table IV. In the development of the formula, the tumbler test, shatter test, screen test, and porosity of coke have been taken into consideration. Each of these tests brings out some physical property not expressed by the others, and in estimation of the importance of these tests as a medium for evaluating coke for the blast furnace, their worth has been graded as follows: It was thought that some additional penalty should be applied to cokes that do not show a uniform screen size, assuming that coke larger than 4 in. was not desirable and that this size was an indication of irregular size. Therefore the screen test factor is further corrected by applying a penalty of 1 pct for each 1 pct material greater than 4-in. size as shown by the screen test. The physical fitness of coke for blast furnace use depends upon four fundamental characteristics: l—gen-era1 strength, as indicated by the shatter test; 2— abradability, or the resistance of cell walls to reduction in size by attrition, as indicated by the tumbler test; 3—porosity; and 4—size and uniformity. Each of these characteristics is not of equal importance, but surely, in an attempt to determine an accurate physical value, the individual value of each should be taken into consideration. The formula is used as a yardstick, so to speak, in determining variations in the normal production of metallurgical coke and in making comparisons between normal coke and experimental blends with other coals. Table IV gives results of coking tests on raw and washed high volatile coals and these same coals with blends of coke breeze, anthracite coal, char and low volatile coals, all from Pennsylvania. The table also gives the source of the coals and coke breeze, as well as their proximate analyses. It will be noted that the washing of the raw high volatile coal increased the physical fuel value from 26.17 to 39.16, showing the effect of removing shale and slate which produces a detrimental fracturing and weakening of the coke. It is a well known fact that many Pennsylvania high volatile coals contain an excess of resinous material or binder which has a tendency to weaken the coke, owing to its high evolution of gases during carbonization. Tests were therefore made with coke breeze, an inert material, in an attempt to alleviate this condition. Blends of washed coal with 5 pct and 7.5 pct coke breeze collected from the coke plant quenching sump (82.9 pct through 1/8-in. screen) resulted in cokes with a physical fuel value of 20.75 and 16.73 respectively, lower than results obtained from 100 pct raw high volatile coal. It will be noted that the percentage of + 4-in. coke increased but that the tumbler test was very low. Undoubtedly better results could have been obtained if the coke breeze could have been crushed extremely fine. During World War II the government asked the coking industry to consider the use of anthracite coal as a substitute for high quality low volatile coal, which was extremely scarce at the time. The next series of tests was made with blends of raw and washed high volatile coals and 5, 10, and 15 pct Pennsylvania No. 5 buckwheat anthracite (100 pct through l/8-in. screen). It was necessary to use some raw high volatile coal in these blends because of insufficient washer capacity at the time. It will be noted that the physical fuel values

Jan 1, 1954

By J. B. Morrow

BITUMINOUS COAL production for 1937 up to Nov. 27, was 400,000,000 ions, an increase of 3.43 per cent over the comparative period in 1936. The in- crease in consumption, however, was not so great as the increase in production. Stocks of coal, mostly in the hands of consumers, on Nov. 1 were 57,000,000 tons, compared to 44,400,000 tons at the same periods in 1936. The prospects were that both production and consumption for December, 1937, would be lower than for the corresponding month of 1936. , Anthracite production for the period ending Nov. 20 was 43,900,000 tons, com- pared to 48,500,000 tons for the corresponding period in 1936, or a decrease of 9.5 per cent. Production of mechanically loaded coal in. 1936 was approximately 57,000,000 tons, an increase of 17.5 per cent over

Jan 1, 1938

By A. F. Banks

INTRODUCTION Selective flocculation-flotation as a method of desliming potash flotation feed has been practiced in the Cominco Ltd. potash plant since November. 1974 when it was installed to replace a less efficient mechanical desliming process. The plant was designed for a consistent feed containing 4.5% insolubles. In practice the quantity and quality of the insoluble material is quite variable. This variability led to serious problems in the deslime circuit and consequently had an adverse effect on sylvite flotation performance. A costly mechanical solution to the problem was being seriously considered when it was drawn to our attention that a selective flocculation-flotation process had been developed. The process was tried first in the laboratory on the Cominco Ltd. ore, then on a pilot basis on 25% of the mill feed and finally full scale. The time from being informed of the process to full scale operation was 18 months. It has since been incorporated into a tailings regrind circuit. The original mine design called for the mining of an 11 foot height up to the top of the three clay seams. These had to be taken as they were a zone of structural weakness. It also assumed that the beds would be uniform with only a few disturbances. Very soon after the initial start up it was found that permanent openings had to take in the layers right up to the upper clay seams and because of the mining process that this material would have to be milled when encountered. The number of disturbed areas in the mine is greater than the design anticipated. In operation the insoluble content of the mill feed varies from 4.5% to 8% plus with the peaks being very short- term to relatively long, from hours to day. In terms of quality, the insolubles in the mining horizon are relatively soft and easily liberated, whereas those above are hard and liberate slowly.

Jan 1, 1979

By E. D. Hummer

During the planning of the fine coal cleaning addition at the Gary, W. Va., Coal Preparation Plant of United States Steel Corp. careful consideration was directed toward the problem of minus 48 mesh refuse disposal. The plant flow sheet included wet screening the raw coal at ¼ in., pumping the minus ¼ in. raw coal to bowl desiltors for desliming, and then cleaning the deslimed raw coal on tables. The material to be removed from the circuit as minus 48 mesh refuse consisted of the minus 100 mesh desiltor overflow thickened in two 120 ft diam thickeners and minus 1 mm screened from the table refuse. Later a flotation plant was added to recover coal from the desiltor overflow, and a classifier replaced the screens to make a sharper size separation of the table refuse at 48 mesh. Today the minus 48 mesh refuse at Gary consists of thickened flotation tailing and thickened spiral classifier overflow. The transportation of large quantities of fine, wet refuse filter cake mixed with jig and table refuse over existing conveying equipment would have been neither dependable nor economical. Filtration was therefore impractical, and disposal of the fine materials was a problem. The decision was to pump the material to storage ponds.

Jan 3, 1965

By J. J. Foster

MOST of us will, I think, agree that never before in the history of the coal industry has the human side of our business been so important as today. Since, even in wholly mechanized mining, labor cost is such a large percentage of out total cost we are all deeply concerned not only about the present attitude of our employees but particularly about the future, when the industry returns to a "survival of the fittest" basis. Many things could and should be done about our employee relations in the coal business. Failure to recognize these obligations and do something about them may lead to serious consequences, the least serious of which will be the loss not only of many of our better employees but a large portion of our potential employees, as they graduate from our schools to other in¬dustries. Some of these things should be handled by the industry as a whole whereas others should be done by individual companies. Due to varying conditions and size of organizations it would, at best, be necessary to vary a program to meet the individual needs of each operator.

Jan 1, 1945

By J. F. K. Brown, E. E. Roecker

For three years The Hudson Coal Co. has used egg anthracite instead of coke in its foundry cupola. It has long passed the stage of being told it cannot be done—the metal would be cold, of poor quality, or the speed of operation would be low. From observation, from use and from test. we know that our metal is about average; the cast iron invokes no adverse comment from the machine shop and the speed suits our foundry requirements. We have there-iore resolved into practice anthracite combustion processes in an industrial furnace formerly using coke, under conditions suitable to our needs. When it comes to translating what we know into use in another cupola, however, where operating conditions may be different, or to explaining why, with seemingly the same conditions in our own cupola, we have attained sometimes a temperature of 2800° in the metal and at another time 2600°, or a speed of 5 tons per hour against 2 35 tons per hour, we cannot do it. We cannot do this because there seems to be an unbridged gap between laboratory ideas on combustion and practical ideas on com-bustiqn, which we have been unable to cross in terms understandable to us as practical consumers. This gap or bridge centers around the problem of how combustion actually takes place; and we believe it is controlled by two factors: (I) the character of the surface of the fuel and (2) the space provided and needed within which the oxygen of the air is allowed to or can act on that surface. It has long been contended on behalf of coke that porosity is an important factor in combustion, although, admittedly, there are two schools of opposing thought on this question, as revealed in technical literature. It has been understood generally that a light, porous coke is the best metallurgical fuel because there are more square inches of carbon exposed to the blast of air, therefore more useful carbon-dioxide reactions can take place in the given space between the entrance of the air and the point where useful work is done. It is now our general idea that the heavier and the harder the coal, the better the metallurgical fuel, provided the surface of that fuel is suitable for fast reaction with the oxygen. Time and Space A cupola is loaded in layers of fuel and iron. The horizontal line where the first charge of iron rests on the coal is the top of the bed coal. With us that is 22 in., usually, above the tuyeres where the air enters. This means 600 lb. of coal. Every subsequent coal layer is 100 to 125 lb. of coal, and that 100 to 125 lb. of coal melts 1000 lb. of iron at around 2700° in the ladle. This quantity of coal represents a 3-in. layer spread across the cupola. The question arises: If this 3 in. of coal will melt 1000 lb. of metal, why was it necessary to use 600 lb., or 22 in., of coal beneath and between the first charge of iron and the air entrance?

Jan 1, 1944

By E. E. Roecker, J. F. K. Brown

For three years The Hudson Coal Co. has used egg anthracite instead of coke in its foundry cupola. It has long passed the stage of being told it cannot be done—the metal would be cold, of poor quality, or the speed of operation would be low. From observation, from use and from test. we know that our metal is about average; the cast iron invokes no adverse comment from the machine shop and the speed suits our foundry requirements. We have there-iore resolved into practice anthracite combustion processes in an industrial furnace formerly using coke, under conditions suitable to our needs. When it comes to translating what we know into use in another cupola, however, where operating conditions may be different, or to explaining why, with seemingly the same conditions in our own cupola, we have attained sometimes a temperature of 2800° in the metal and at another time 2600°, or a speed of 5 tons per hour against 2 35 tons per hour, we cannot do it. We cannot do this because there seems to be an unbridged gap between laboratory ideas on combustion and practical ideas on com-bustiqn, which we have been unable to cross in terms understandable to us as practical consumers. This gap or bridge centers around the problem of how combustion actually takes place; and we believe it is controlled by two factors: (I) the character of the surface of the fuel and (2) the space provided and needed within which the oxygen of the air is allowed to or can act on that surface. It has long been contended on behalf of coke that porosity is an important factor in combustion, although, admittedly, there are two schools of opposing thought on this question, as revealed in technical literature. It has been understood generally that a light, porous coke is the best metallurgical fuel because there are more square inches of carbon exposed to the blast of air, therefore more useful carbon-dioxide reactions can take place in the given space between the entrance of the air and the point where useful work is done. It is now our general idea that the heavier and the harder the coal, the better the metallurgical fuel, provided the surface of that fuel is suitable for fast reaction with the oxygen. Time and Space A cupola is loaded in layers of fuel and iron. The horizontal line where the first charge of iron rests on the coal is the top of the bed coal. With us that is 22 in., usually, above the tuyeres where the air enters. This means 600 lb. of coal. Every subsequent coal layer is 100 to 125 lb. of coal, and that 100 to 125 lb. of coal melts 1000 lb. of iron at around 2700° in the ladle. This quantity of coal represents a 3-in. layer spread across the cupola. The question arises: If this 3 in. of coal will melt 1000 lb. of metal, why was it necessary to use 600 lb., or 22 in., of coal beneath and between the first charge of iron and the air entrance?

Jan 1, 1944