Search Documents

By G. F. Huff, G. R. Bailey, J. H. Richards

An improved bomb-sampling technique for obtaining samples for oxygen analysis from liquid steel is described. Analyses of samples taken from open-hearth furnaces by the improved method show sufficient agreement with laboratory data to indicate the accuracy of the method is better than that of other existing sampling methods. THE bomb-sampling method of determining the oxygen content of a liquid-steel bath was studied by obtaining and analyzing more than 200 samples from normal open-hearth heats. Of these samples, about 60 were obtained with a bomb of conventional design;' the remainder were taken with a somewhat modified bomb designed to give greater protection against slag contamination. In the new device, the contacting faces of the cast-iron mold halves are machined so that they fit closely; the opening at the top of the bomb is covered with a thin steel cap; and the top of the bomb is further covered with a wood block held in place by heavy steel wire. After the bomb has passed through the slag layer and has entered the steel bath, the wire melts and the wood block floats to the surface. Thereafter, the steel melts through the thin cap and flows into the bomb cavity where it is deoxidized with aluminum wire. An assembled bomb, ready for sampling, is shown in Fig. 1. To standardize sampling procedure, the samples were usually taken through the center door and at the bottom of the furnace; that is, the bomb was on the bottom when the metal cap melted. After each addition to the furnace, at least 20 min elapsed before a sample was taken. The oxygen contents of all the samples were determined by using the vacuum-fusion method, two or more specimens from each sample being analyzed. The specimens were cubes of metal cut from a region in the interior of the bomb sample, as shown in Fig. 2. Drillings for carbon analysis were obtained immediately above the oxygen-analysis region. Reproducibility of Results In determining the reproducibility of the results obtained with the modified bomb, the following four factors were studied: 1—variation in the oxygen concentration of duplicate specimens taken from a single sample; 2—variation in the oxygen concentration of duplicate samples taken in quick succession: 3—effect of the amount of aluminum wire

Jan 1, 1953

By H. R. Peiffer

Recently artin has indicated that the recovery of resistivity at 145°C following elongation of molybdenum at room temperature was the result of the annihilation of vacancies. The activation energy for this process was, according to Martin, 1.26 ev. This energy seems to be a reasonable one for the activation energy for the diffusion of vacancies in molybdenum. However, impurity atoms such as carbon, nitrogen, and oxygen4 have an activation energy for diffusion in molybdenum of the same order of magnitude (i.e., 1.45, 1.15, and 2.09 ev, respectively). Cottrell and Churchman have already correlated the return of impurity atoms to dislocations in cold-worked iron with the return of the upper and lower yield point. According to cottrel16 the diffusion of carbon atoms to dislocations results in the return of the yield point. As the carbon atoms become trapped by dislocations, Bhatia has shown that a decrease in the electrical resistivity is to be expected. Cottrell and Churchman were able to correlate experimentally the decrease in electrical resistivity with the return of the yield point. Since one would expect strain aging to occur in molybdenum, an experiment was performed to determine whether the resistivity recovery at 150°C for molybdenum cold-worked at room temperature can be correlated with the return of an upper and lower yield point. For this experiment 3/16-in. tensile bars of Climax molybdenum, 99.961 pct pure, were used. The specimens were annealed at 1000° C for 1 hr in an argon atmosphere and then were elongated up to 10 pct on a Baldwin-Lima-Hamilton FGT

Jan 1, 1959

By R. F. Jones, N. E. Truitt, M. Prats

In most published discussions and theories of in situ combustion, the combustion fronts are assumed to be vertical. However, evidence from field tests leaves no doubt that combustion fronts often advance more rapidly along the top than near the bottom of a formation as a result of difference in density between injected air and formation liquids. The approximation proposed in this paper to determine the movement of the resultant tilted combustion surfaces states that the vertical rate of movement of combustion surfaces is proportional to the horizontal oxygen flux. Where self-ignition is possible, the proposed method demands that a secondary combustion surface exist around production wells which produce some oxygen. These secondary combustion surfaces may be formed long before the primary combustion surface can advance from injection to production wells. Heat liberated near production wells at these secondary combustion surfaces can contribute to an early increase in production rate. Results indicate that significant oil recoveries cannot be obtained from the usual flood patterns (five-spots, seven-spots, etc.) without producing large volumes of unused oxygen. Ideally, to increase oxygen- consumption efficiency, well patterns should allow oil production from a first line of production wells and gas production from more distant lines of producers. However, it may be desirable to produce some gas at all wells to support (and benefit from) active secondary combustion surfaces. Results indicate that the well spacing through which combustion can be advanced is larger than that predicted by other methods. A large number of production wells may still be desirable to take quick advantage of gravity drainage. From a comparison with results at South Belridge field, California, it appears that this method adequately describes oxygen concentration and temperature histories and combustion-front shapes. However, this method does not accurately locate the most advanced point of the combustion surface. There is some field evidence to substantiate the actual presence of secondary combustion surfaces at South Belridge. Use of the proposed method appears warranted at this time when lay-over of the combustion surface can be anticipated. INTRODUCTION The assumption of vertical combustion fronts has been embodied in all previous publicationsl-6 which use the movement of combustion fronts away from injection wells to determine the temperature and fluid distributions in the reservoir. The only paper concerned with a mathematical model of the combustion process in which a nonvertical combustion front is used was written by Gottfried.11 Actually, nonvertical combustion fronts have been observed in most in situ combustion field tests for which adequate data are available.7, 8, 6 In practice, the typical vertical extent of the burned zone decreases with distance from the injection well, and this burned zone is at or near the top of the sand body. In some cases, such as at South Belridge field near Taft, Calif., the combustion surface is almost horizontal over a very large area.8 Thus, for some years an obvious and serious gap has existed between theory (vertical fronts) and practice (tilted fronts). This is indicated in Fig. 1. Tilted combustion fronts such as observed at South Belridge8 sometimes result from the natural tendency of injected gases to rise to the top of an oil sand. An initially present gas cap, even if thin, would make apparent the effect of gravity segregation from the first, particularly since formations considered for in situ combustion field operations are generally selected for their

Jan 1, 1969

By H. F. Seifert

THE classification and preparation of non-ferrous scrap metals is a subject of interest to every individual and corporation that employs in its processes of manufacture non-ferrous metals and alloys and accumulates in such manufacture scrap from these materials for disposition in the form .of turnings, borings, short ends, punchings, clippings, grindings, washings, etc. All too frequently the disposition-of such scrap is left to individuals who have no knowledge of the subject either from a metallurgical or a commercial standpoint, or both. Much money is thus lost which with a little more intelligent effort might be saved, and in this day of fierce competition and small profits such an opportunity cannot be ignored. The Mineral Resources of the United States for the year 1925, the latest issue available (Part 1, page 221), gives the secondary non-ferrous TABLE 1.-Some. Secondary Non-ferrous Metals Recovered in the United States for the -Year 1924-25 Material Short Tons Value Copper, including that in alloys other than brass.... 250,600 8 71,170,400 Brass, scrap remelted : 242,300 56,270,800 Lead as metal : 112,420 39,477,100 Lead as alloys 112,460 Zinc as metal 61,430 11,359,000 Zinc in alloys other than brass 13,300 Tin as metal 7,950 Tin in alloys 23,000, 35,165,400 Antimony as metal 1 3,794,000 Antimony in alloys : 10,839 Aluminum as metal 17,700 24,816,000 Aluminum in alloys 26,300 Nickel as metal 191 1,518,000 Nickel in non-ferrous alloys 2,109 Total l 882,600 $243,570,700

Jan 1, 1928

By W. T. lsbell

HERCULANEUM, MO., about thirty miles south of St. Louis on the Mississippi River, is the site of the lead smelter of the St. Joseph Lead Co. The lead concentrates come by rail from the Flat River district and from three properties in Madison County, Missouri; from the Balmat division in St. Lawrence County, New York; a small tonnage from the Tri-State district; and occasionally from the Aguilar property in Argentina. The average grade is 67 to 68 percent lead and 1 to 3 oz of silver. The bulk of the material is flotation concentrate, with some gravity or table concentrate. No secondary metals, outside drosses, or any materials high in bismuth, arsenic, or antimony are treated. All concentrate is received in box-caps and is unloaded directly from a trestle into the concentrate bins at the roaster plant. Flux, coke, and any miscellaneous lead-bearing material is either unloaded directly into bins or unloaded with a locomotive crane. All moving and switching of cars is done with two thirty-ton steam locomotives. Shipping facilities for the plant are provided by the Missouri-Illinois Railroad. Water for the plant and for fire protection is obtained from a dam built in a near-by creek. Drinking water both for plant and town is obtained from

Jan 1, 1947

By C. E. Mills

STUDIES of ground movement and subsidence resulting from mining operations cover a broad field. It is also a very important consideration and one that eventually affects nearly every mining operation of any extent. The damage to surface buildings, removal of mine surface plants and replacements of main hoisting shafts must reach an astounding expenditure were these cost figures available over a period of years. Were the subject one of mathematical formula and dependent only on the angle of draw of the walls or country rocks, the problem would be relatively simple. Consideration must be given to depth and extent of workings; structural conditions of the orebodies and enclosing country rock; physical properties of these same rocks, including schistosity, bedding, jointing, slips, dikes, faults, and other structural weaknesses. The method of mining, extent of openings, supporting pillars, and amount of moisture or water underground are other pertinent factors. With such a large number of variable factors, it is apparent that the subject of subsidence is one that must be based largely on experience and results at other mines where conditions are somewhat comparable. In presenting this paper, it is the intent to describe the progressive results of past ground movements at the United Verde, to bring out physical conditions largely responsible for this movement, but to refrain from theorizing on the ultimate extent of subsidence resulting from future mining operations.

Jan 1, 1934

By W. J. Helfrich, R. A. Dodd

Binary aluminum solid-solution alloys containing various amounts of silver, magnesium, and zinc were prepared by careful directional solidification, and the hydrostatic and X-ray densities were compared. With the exception of the Al(Ag) alloys, the X-ray densities were consistently greater than the hydrostatic measurements, in agreement with earlier observations by Ellwood. In contrast to Ell-wood's interpretation in terms of vacant lattice sites associated with Brillouin zone effects, a tentative explanation based on the existence of solidification microshrinkage was favored. This hypothesis was confirmed by an examination of Al(Zn) alloys prepared by vapor diffusion of zinc into aluminum. The hydrostatic and X-ray densities were now in very close agreement, and it was concluded that the filling of Brillouin zones in aluminum solid-solution alloys does not necessarily result in the formation of defect structures containing an excess of vacant lattice sites. ThE existence of defect structures of the vacancy type in alloys in which the excess vacancies have an electronic rather than a thermal or mechanical, and so forth, origin is well recognized. Examples of incomplete lattices of this type are to be found in the Ni-Al,1-3 Fe-Ni-A1,4 c~-Ni-Al,5 Fe-Cu-Al,= and Co-A17 systems. These defect structures are of a special kind in that the intermediate phases possess an ordered atomic arrangement or superlattice, and in some instances the vacancy concentration may be unusually large, e.g., at 45.25 at. pet Ni in NiA1, approximately 8.8 pet of the lattice sites are unoccupied. Ellwood8-10 has reported similar defect structures in the aluminum solid solution alloys of the Al-Zn and A1-Mg systems and in alloys of the Au-Ni system." In Al(Zn) the (apparent) vacancy concentration rose, somewhat irregularly, to a maximum of about 2 pet vacant sites at 25 at. pet Zn, while in Al(Mg) the (apparent) vacancy concentration increased continuously to 1.7 pet at 15 at. pet Mg. An explanation in terms of Brillouin zone overlap was attempted, although Pearson12 has pointed out the difficulty of reconciling the observations with zone theory. However, the possibility of the effect being caused by the Fermi surface just touching a plane of energy discontinuity inside a prominent Brillouin zone has, in general, been accepted. In fact, Massal-ski13 has interpreted Ellwood's8 observations as confirmation of Leigh's14 theoretically predicted zone overlap occurring at approximately 2.67 electrons per atom. Unfortunately, Massalski was apparently unaware that Ellwood9 had revised his earlier results considerably, and the revised data did not confirm Leigh's analysis. Ellwood's clata were reexamined by the present authors who noted a possible correlation between the percentage defects as a function of alloy composition and the temperature interval of solidification measured from the respective equilibrium diagrams. This suggested an explanation in terms of shrinkage porosity rather than vacant lattice sites, and pointed to the desirability of reexamining appropriate alloy systems using: both Ellwood's method of specimen preparation (casting followed by wrought fabrication) and alternativ'e methods, i.e., diffusion, which might be expected to minimize, or even completely obviate, microporosity. ALLOY PREPARATION 1) Cast Allolys and Aluminum Single Crystals. Al(Ag), Al(Mg;l, and Al(Zn) alloys of various compositions up to 20 at. pet silver, 13.5 at. pet mg, and 30 at. pet Zn were prepared by melting under helium and casting into graphite molds. In the first two systems, the maximum alloying addition was quite close to the limit of solid solubility, but the possibility of transformation to a' during quenching somewhat restricted the suitable Al(Zn) composition range. The alloys were prepared from high-purity aluminum, a lot analysis showing 0.002 wt pet Cu, 0.002 wt pet Fe, and 99.996 wt pet A1 by difference. The silver, magnesium, and zinc were of 99.99+, 99.98+, and 99.998 wt pet respectively. Each composition was analyzed chemically. The as-cast ingots measured 7/16 in. diam and 5 in. length. One in. was removed from the top of the ingot, and the bottom 3 in. was machined to 0.275 in. diam; a point was also machined on the smaller diameter end. The remainder of the original ingot served as a top riser during subsequent remelting and controlled solidification. The machined ingots were now remelted using a Bridgman soft-mold technique to ensure directional solidification and, therefore, a minimum of micro-shrinkage. Alumina powder was used as mold material contained in an alundum thimble, and this crucible was placed in a helium-filled Vycor tube. The assembly was lowered through a suitable temperature gradient at approximately 0.5 in. min-l, and the risered portion of the casting was subsequently removed by sawing.

Jan 1, 1962

By J. B. Cohen

In an investigation of the microstructure of shock-loaded metal specimens1 C. S. Smith found that there was little distortion of grain boundaries or change in external dimensions, although the hardness corresponded to that produced by severe rolling. Furthermore, the hardness of individual grains was independent of the deformation structures present; grains with no markings were as hard as those heavily populated with markings. These markings which resemble twins do not appear in copper until high shock-loads of the order of 200 kb are applied. It appears that due to the high velocity of a shock wave and its sharp front, heavy deformation takes place on a submicroscopic scale. In this work an attempt was made to examine this deformation, particularly at a load below which macroecopic markings appear. The broadening of 200 and 400 diffraction peaks was examined from the face of a poly crystalline sample normal to the direction of the shock wave. These peaks were chosen because the elastic constants in copper are such that residual strains would be greatest in the <100> directions; hence, the strain-broadening contribution to these peaks would be large in comparison to other sets. Also the broadening due to stacking faults and microtwins would be greatest with this set.2 A complete Fourier analysis of these peaks was made, as described by warren,&apos; using the Stokes correction with peaks from an annealed sample.3 With the aid of the U. S. Army Ordnance Corps EDVAC computer and a curve matching program, sixty sine and sixty cosine coefficients were obtained for each peak. The last of these was about 1.5 pct or less of the largest coefficient, indicating good representation. Transverse sections from a 1.5 in. rod of as-drawn electrolytic tough-pitch copper were reduced in cross-sectional area about 50 pct by cross rolling. Disks 1.5 in. in diam were recrystallized at 275 °C for 30 min and then at 300°C for the same time. The faces were polished and deeply etched in nitric acid to remove 25 mils. The grain size was 0.02 mm. Laue back-reflection patterns indicated the sample was well recrystallized. The two diffraction peaks from this sample were recorded on a Norelco diffractometer using filtered copper radiation. Peak intensities were kept less than 600 cps to assure linearity of the counter and circuitry. This sample was then placed between two rods of the same material and diameter. The top rod was 2.25 in. long and the bottom rod 1 in. long. (In

Jan 1, 1961

The accompanying sketch shows the interesting position of Salt Lake City with reference to Western mining areas and justifies its title "The Center of Western Mining." In the last twenty years, the area embraced within a circle of 600 miles radius with Salt Lake City as its center has produced 79.87% of the gold, 91.9% of the Silver, 77.47% of the copper, 53.61% of the lead and 26.55% of the zinc produced in the United States, including Alaska. This area also contains the greatest coal deposits of the continent, some of the greatest oil deposits, great iron deposits and many other important mineral resources. The 600-mile circle contained 69% of the active operators of other than coal mines and 40% of the men employed in mines other than coal mines of the United States, including Alaska, for the four-year period ended with 1923.

Jan 1, 1925

The Industrial Minerals Division met jointly with the Materials and Equipment Division of the American Ceramic Society at State College, Pa, Sept 24-26 Headquarters were at the Nittany Lion Inn Thurs- day afternoon was devoted to a tour of inspection of the Bell Mine, American Lime and Stone Co , Bellefonte, Pa The party returned to State College for dinner and in the evening the Division&apos;s executive committee held a brief session There were four technical sessions Friday morning, Mining, afternoon, Beneficiation, Saturday morning, Industrial Minerals and Beneficiation There was an informal banquet at the Nittany Lion Inn Friday night with 93 present Edward Steidle was toastmaster Brief talks were made by President F C Flint and Secretary Ross Purdy, of the American Ceramic Society, Oliver Bowles, Chairman, Industrial Minerals Division, Adrian Morse, assistant to the president, Pennsylvania State College, and George Otis Smith, past president A I R&apos;I E

Jan 1, 1937

On Sept. 22 to 26, the Institute will hold its 120th meeting in Chicago. The program arranged provides for technical sessions on: Mine Taxation, Non-ferrous Metallography, Coal and Gas, Milling, Oil, Industrial Organization, Geology, Non-ferrous Metallurgy, Mining and Local Resources, Iron and Steel, Symposium on Sulfur Coals, Symposium on Pyrometry. Inspection trips have been arranged to: Gary Steel Plant. La Salle District: Zinc smelters, coal mines, cement works, America&apos;s first permanganate plant, many varied industries, scenic trips. North Chicago and Milwaukee: Mining-machinery manufacturing plants, tungsten and molybdenum reduction plants. East Chicago and Whiting: Lead refinery, oil refinery. Franklin and McCoupin: Coal fields. Chicago: Nearly every kind of metallurgical and manufacturing industry. MONDAY, SEPT. 22d Morning Registration, Non-ferrous Metallurgy, Coal and Gas. Afternoon Coal and Gas Milling Industrial Geology, etc. Evening Smoker. TUESDAY Morning Gary. Afternoon Gary. Iron and Steel. Evening Oil, Iron and Steel.

Jan 9, 1919

By G. W. Phelps

The field of industrial minerals is concerned with both sieve size and distribution of sub-sieve particles. A great deal of work has been reported on the techniques designed to provide information of this work. The term sub-sieve is here considered to include particular material that will pass a 325-mesh testing sieve. Plant men require rapid, precise and simple testing techniques that are, if possible, inexpensive with respect to equipment and manpower. A number of particle-size procedures have been developed, based on the Stokes equation for streamline movement of a particle of diam D, moving at velocity V through a liquid of viscosity n. 1 Particles are considered to be rigid, smooth spheres, completely dispersed at low concentration and moving at low velocity through the suspending medium with no slippage between particle and liquid. In particle size determinations the particle moves either from natural gravitational forces or those provided by centrifugal means. The diagram of Fig. 1 shows a spherical particle of density S and diam D moving downward at velocity L/T (or V) through a liquid of density So and viscosity n. The forces of gravity G (natural) or Gc (centrifugal) cause the particle to move through the liquid, thereby creating a viscous drag F or Fc. Within the streamline flow

Jan 1, 1967

By F. L. Bosqui

Discussion of the paper of F. L. Bosqui, presented at the San Francisco meeting, September, 1915, and printed in Bulletin No. 101, May, 1915, pp. 997 to 1033. H. A. WHITE, Springs, Transvaal (communication to the Secretary*). -It is, as the author points out in his valuable paper, a, fact, that in many plants the "trommel washings" are allowed to become eyesores, but the simpler system of pumping the entire product direct to the tube-mill circuit will avoid the extra expense of separation and small-scale treatment when one considers the relative distance of the points and the proportionately small amount of water. It is a matter of record that in stamp batteries the increase of weight has been developed concurrently with the increased use of tube mills, but independently and on its own merits. The satisfactory duty, excellent running time, and freedom from breakages in the newer mills, such as the Modder Deep, with 2,000-1b. stamps, will probably go far in removing some of the conservative prejudices mentioned by Mr. Bosqui. The success of the City Deep trial of the Nissen stamp cannot be entirely attributed to better feed distribution and discharge effects (published experiments on two-face discharge mortar boxes showed no advantages). Attention is directed to the treatment costs given by the author both before and after the increased capacity resulting from the addition of 16 Nissen stamps at Modder B. It will be observed that the only item of cost resisting the tendency to reduction caused by increased tonnage is that of milling, which has risen 1.3c. With reference to the provision for amalgamation in the new plans, it seems obvious that a great loss of head would be eliminated by passing the tube cone overflow over a separate top series of plates; three at the top and three at the bottom will effect the maximum amalgamation. This plan is followed at the Princess Estate and Gold Mining Co., Ltd., Modderfontein Deep Levels, Ltd., and Geduld Proprietary. Mines, Ltd., but elsewhere reliance is placed upon ample cone capacity and the underflow only is passed over three plates after going through the tube mill, while the overflow is passed direct to the cyanide works; both methods avoid the largely unnecessary elevation of considerable quantities of water, fine sand and slime involved in Mr. Bosqui&apos;s scheme.

Jan 1, 1916

By A. B. Kinzel

IT is with sincere appreciation and a deep sense of responsibility that I accept the honor of delivering the Howe Memorial Lecture. In our time metallurgical research has delved into phenomena ever more complex in character, so that much of this work must be done by organized teams. We, of the Union Carbide and Carbon Research Laboratories and the Electro Metallurgical Co., are truly a team and the lecture which is to follow is due largely to a few of the outstanding members of that team here cited and well known to you in their own right: John Lamont, whose work deserves special recognition, Walter Crafts, William Forgeng, William Binder, Robert Fowler, and David Swan. Thus it is a fitting pleasure to accept this honor for the research institution which I represent. Henry Marion Howe was truly inspirational and his breadth of view was such that he could use either the method of rigid proof or implied mechanism to further the broad understanding. But perhaps his outstanding characteristic was his sound judgment and his ability to weigh observations. The following is replete with observations and judgment as to their implication. We would like to feel that it is the type of dissertation which Howe, himself, would have enjoyed. Chromium carbides in stainless steel have, in a sense, been a key to the progress of the stainless steel industry. Brearley&apos;s first stainless steel, containing approximately 0.30 pct C, was successful because it differed from previous Fe-Cr alloys in that the carbides were present in such amount and form as to provide the stainless and cutting properties. Again, the 12 pct Cr die steels with a carbon content of 1.5 pct or more achieved their properties by virtue of the form and distribution of the chromium carbides. In the straight chromium steels with from 12 to 25 pct Cr, chromium carbide amount and distribution are once more the determinants with respect to physical properties and corrosion resistance. In each of the cases just cited the role of the carbide is in essence similar to that of iron carbide in carbon steel and this story is so well known that we need not dwell on it. In the austenitic stainless steels, the chromium carbide plays only a minor positive role with respect to mechanical properties, and for corrosion resistance the objective is to achieve maximum homogeneity. Thus the tendency has been to ever lower the carbon and correlatively the chromium carbide content of the austenitic steels. Today stainless steels with carbon less than 0.03 pct are beginning to find their true place, and this is being aided in major degree by our Company&apos;s introduction of a new type of ferrochromium having negligible carbon. The role of carbon in these austenitic steels has long been recognized, and a truly enormous amount of research has been devoted to the subject. Much has been learned about corrosion resistance, but the attack on the problem from the point of view of carbide precipitation and the nature thereof has left much to be understood. Because of its fundamental importance to the future of stainless steels, further study of the mechanism of carbide formation in austenitic steels is of interest. In the 18-8 Cr-Ni steels, which are typical of the austenitic class of steel, carbon is soluble in the aus-tenite to the extent of approximately 0.15 pct at 1832°F (1000°C). The solubility becomes less with decreasing temperature, so that at 1652°F (900°C) the solubility limit is approximately 0.06 pct, at 1472°F (800°C) it is about 0.03 pct, and at 932°F (500°C) it is approximately 0.01 pct. Obviously this is the ideal situation for the classical precipitation phenomenon. It is true that, in a sense, 18-8 austenite resulting from annealing is in a metastable state, and the phenomenon of ferritic precipitation from this austenite should be considered. However, in a so-called fully austenitic 18-8 steel this is secondary with respect to the carbides and can be neglected. A wide variety of chromium carbides is known. Only one chromium carbide, Cr,,C,,, frequently referred to as Cr,C, has been found in unmodified low carbon 18-8 steel. This, fortunately, simplifies the study of the precipitation phenomena. For this study an A.I.S.I. type 304 stainless steel of commercial quality was selected. Analysis showed C 0.07 pct, Mn 0.49 pct, Si 0.33 pct, Ni 9.34 pct, Cr 18.91 pct, and N 0.033 pct. As expected with this composition the steel was homogeneous after annealing except for a few pools of ferrite, which were disregarded in that their location was not coincident with subsequent carbide precipitation areas. On corrosion testing the steel was normal and typical of good commercial quality. Specimens 1/2xlx4 in. were annealed and subjected to precipitation heat treatment for 100 hr at 100" temperature intervals from 1000° to 1500°F and for ten selected intervals ranging from 5 min to 64 hr at 1300°F. These blocks were then cut into small pieces for metallographic studies. The first problem

Jan 1, 1953

By Kenneth M. Bravinder, Jonathan E. Koogle, Dean H. Sheldon

The solution of subsurface geological problems requires an analysis of vertical and horizontal dimensional relationships. For many, the ability to visualize structures in three dimensions is not easily acquired, and for areas where the structural conditions are complicated by faulting the need arises for illustrative models. This has led to the many forms of peg models, in which the usual course of construction includes a peg for the well bore, and the suspension of strings from peg to peg to illustrate the formation correlation between wells, thus developing the usual folds and flexures. Such models proved unsatisfactory for the analysis of fault problems. Consideration was then given to the use of transparent materials. A model of the Dominguez oil field was constructed in 1935, which consisted of a series of glass panels irom well to well on which the formations were shown in color. This model, though serving its purpose at the time, proved to be impractical from the standpoints of cost, breakage hazard, and extreme difficulty in maintenance. The cost of materials was estimated to be approxi-mately $300, and the construction required the services of one man for a period of from 10 to 12 months. Maintenance after actual construction was an additional expense. Consideration was then given to the use of celluloid, and aiter some experimental work it was found that the advantages in its use were: (I) a short construction time, (2) ease of handling the material, (3) sec-tions are easily reworked, (4) low cost. Construction It would be of little value to recount here the difficulties encountered in the building of the first celluloid model. The conclusions drawn, however, suggest the following pro-cedure for those who contemplate the construction of such a model: 1. Determilzatiolz of the Scale.—Accurate geological interpretation requires the use of the same scale horizontally and vertically. It should be emphasized that the limited size of the celluloid sheets (20 by 48 in. maximum dimensions), the area to be studied, the maximum depths to be plotted, and area of possible future development are the controlling factors in adopting a scale to he used. 2. Construction of the Base.—A satisfac-tory base may be constructed by using two pieces of three-ply wood separated by strips of I by 2-in. material. This type of construction prevents warping of the base. The size of the base is determined by the dimensions of the area to be studied plus 5 in. on all sides. A map of the same scale as that adopted for the model, indicating the lines of section to be used, should be fastened to the base. 3. Constructiolt of the Frame (Fig. I).—In the construction of the frame the use of %-in. 0.d. pipe welded in a box shape is suggested, with two horizontal rods on each of the four sides, top and bottom. The top rod should be at least r in. higher than the

Jan 1, 1941

By Kenneth M. Bravinder, Jonathan E. Koogle, Dean H. Sheldon

The solution of subsurface geological problems requires an analysis of vertical and horizontal dimensional relationships. For many, the ability to visualize structures in three dimensions is not easily acquired, and for areas where the structural conditions are complicated by faulting the need arises for illustrative models. This has led to the many forms of peg models, in which the usual course of construction includes a peg for the well bore, and the suspension of strings from peg to peg to illustrate the formation correlation between wells, thus developing the usual folds and flexures. Such models proved unsatisfactory for the analysis of fault problems. Consideration was then given to the use of transparent materials. A model of the Dominguez oil field was constructed in 1935, which consisted of a series of glass panels irom well to well on which the formations were shown in color. This model, though serving its purpose at the time, proved to be impractical from the standpoints of cost, breakage hazard, and extreme difficulty in maintenance. The cost of materials was estimated to be approxi-mately $300, and the construction required the services of one man for a period of from 10 to 12 months. Maintenance after actual construction was an additional expense. Consideration was then given to the use of celluloid, and aiter some experimental work it was found that the advantages in its use were: (I) a short construction time, (2) ease of handling the material, (3) sec-tions are easily reworked, (4) low cost. Construction It would be of little value to recount here the difficulties encountered in the building of the first celluloid model. The conclusions drawn, however, suggest the following pro-cedure for those who contemplate the construction of such a model: 1. Determilzatiolz of the Scale.—Accurate geological interpretation requires the use of the same scale horizontally and vertically. It should be emphasized that the limited size of the celluloid sheets (20 by 48 in. maximum dimensions), the area to be studied, the maximum depths to be plotted, and area of possible future development are the controlling factors in adopting a scale to he used. 2. Construction of the Base.—A satisfac-tory base may be constructed by using two pieces of three-ply wood separated by strips of I by 2-in. material. This type of construction prevents warping of the base. The size of the base is determined by the dimensions of the area to be studied plus 5 in. on all sides. A map of the same scale as that adopted for the model, indicating the lines of section to be used, should be fastened to the base. 3. Constructiolt of the Frame (Fig. I).—In the construction of the frame the use of %-in. 0.d. pipe welded in a box shape is suggested, with two horizontal rods on each of the four sides, top and bottom. The top rod should be at least r in. higher than the

Jan 1, 1941

By Stuart St. Clair

EARLY in 1936, when the American Petroleum Institute issued -J "American Petroleum Industry," which was a survey of the current position of the petroleum industry, and its future outlook, and the figures for petroleum requirements .for 1950 and 1960 were widely publicized by the several oil journals, the impression was given that the petroleum- industry must be nearing maturity and would by 1950 have passed the high&apos; point of its obligations to business progress in the United States.`&apos; Let -us look at the figures which might conduce, this thought. Referring to p. 32 of the report, the total indicated crude-oil requirements in 1940 are 1,099,000,000 bbl-; for 1950, the peak, 1,109,800,000 bbl.; for 1960 a decline to 1,071,020,000 bbl. This downward trend, then established, is probably expected to continue. And this in the face of a crude production in 1935 of 993,942,000 bbl., 38,858,000 bbl.

Jan 1, 1936

By E. Miller, K. L. Komarek, M. Ettenberg

The activity of aluminum in solid Co-A1 alloys has been measured by an isopiestic technique between 850° and 1200°C from 45 to 80 at. pct Al. The activity shows a Precipitous decrease around the stoichzornetric composition of CoAl. Free energies of mixing have been calculated over a limited composition range. Considering an antistructure-vacancy defect mechanism, the degree of intrinsic disorder, a , in CoAl was related to the alunminum activity. Excellent agreement between the calculated and experimental activity curves was obtained for a = 1.25 x 10-4. ThERMODYNAMIC properties of solid aluminum-transition metal alloy are being studied in an investigation of disordering in ordered compounds. In a continuing series of investigations, activities of solid Fe-1,&apos; Ni-A1, kd r-A13 alloys have been measured. From the results for Fe-A1 and Ni-A1, the degree of intrinsic disorder for the equiatomic compounds was calculated2 using equations derived by Wagner and chottk. From the results for Cr-A1 the degree of intrinsic disorder was calculated from equations derived by Orr.&apos; In this paper, the results of the study of Co-A1 alloys are described. Published activity data in the Co-A1 system has been limited to liquid alloys at 1600°C.° A heat capacity study7 of stoichiometric CoAl indicated that a second-order phase transformation occurs at 790° C, attributed to an order-disorder reaction. Oelsen and Middel,&apos; employing the calorimetric mixing of pure liquid metals, obtained heats of formation for compositions from 6 to 90 at. pct Co. Heats of formation for 50 and 78 at. pct Co alloys have also been measured by acid solution calrimetr. The Co-A1 phase diagram, as compiled by Hansen and Anderko,lo is in good agreement with more recent X-ray evidence. The method for measuring activities of aluminum in this study is essentially that employed in the studies of the Fe-1,&apos; i-Al, and r-A13 systems. This isopiestic method entails placing cobalt specimens, in a temperature gradient, in a sealed alumina system containing a pure liquid aluminum source of fixed vapor pressure. The specimens are equilibrated, cooled to room temperature, and their final compositions determined. From the measured temperature of the specimens and the known vapor pressure of pure aluminum the activities of aluminum in the alloy can be calculated. EXPERIMENTAL PROCEDURE The cobalt was 3-mil-thick sheet of 99.9 pct purity (herritt Gordon Mines Ltd., anada). The major impurities were 0.1 pct Ni, 0.014 pct C, 0.018 pct Fe, 0.004 pct S, and 0.005 pct Cu. The aluminum metal had a purity of 99.99 pct (Aluminum Corp. of America) and all alumina parts were 99.7 pct A1,O3 (Triangle RR Grade, Morganite Refractories, Inc.) with major impurities 0.05 pct SiOz, 0.1 pct Fe203, 0.2 pct NazO, and 0.05 pCt K20. Runs 1 to 3 were made with annular cobalt specimens (12 mm ID by 21 mm OD) punched from the sheet. The specimens were deburred and degreased in carbon tetrachloride and in acetone. The samples, each weighing about 150 mg, were then positioned along an alumina rod, a in. OD by 14 in. long, separated by alumina spacers, i in. ID by | in. OD by & in. long. The lower end of the rod was placed in a hole drilled in the center of an 80-g aluminum cylinder. This assembly was put into an alumina crucible, 1+ in. ID by 13 in. OD by 3+ in. high, and the position of each sample was measured to within 50.5 mm relative to the bottom of the crucible. An alumina tube, 28.5 mm ID by 35.5 mm OD by 14 in. long, closed at the top, was slipped over the whole assembly, so that it fitted snugly into the bottom crucible. The entire reaction assembly was tied with molybdenum wire and lowered into a mullite tube, closed at the bottom. A quartz thermocouple tube, closed at one end, containing a t/Pt-10 pct Rh thermocouple, calibrated according to the specifications of the National Bureau of standards,&apos;&apos; was placed along the reaction assembly inside the mullite tube. The temperature of each specimen could be determined by gradually raising the thermocouple and measuring the temperature gradient along the reaction assembly. The combined error in temperature measurement and sample position resulted in a total error of Q°C in the recorded temperature of each sample. The mullite tube was sealed at the top by a water-cooled brass head, connected to a conventional glass vacuum system. The aluminum reservoir is heated to its melting point sealing the alumina system containing the samples. During this process the pressure is maintained below 0.01 li Hg. During subsequent heating to establish the proper temperature gradient and throughout the entire run the pressure is maintained below 2 1 Hg by means of a two-stage mechanical pump. Equilibration runs lasted from 4 to 6 weeks and were terminated by air cooling. The temperature of the liquid aluminum reservoir was brought below its melting point in less than 20 min. For runs 4 and 5, alloy buttons with 49 and 69 at. pct A1 were prepared from the initial high-purity metals by arc melting under purified argon. The alloy buttons were comminuted to powder with an alumina mortar and pestle until the powder passed through a 400-mesh screen, particle size 0.0014 in. Portions of this powder weighing between 50 and 200 mg were placed in small alumina trays, 25 by 15 by 5 mm, which were then

Jan 1, 1969

By John B. Hastings

THE origin of the watery vapors of vulcanism has always been an object of interest and speculation to the seismologist, and as theories of the genetic origin of ore-deposits have of late years been pretty well narrowed down to the expiring forces of plutonic action, the same question has had a lively interest for mining engineers and geologists, as is well shown by the discussions of the subject in our Transactions. The important part taken by volcanic emanations in the origin of pegmatites and quartz-veins, described in my paper, Origin of Pegmatite,1 and their latent power to concentrate into useful deposits such scattered gold as occurs in the Hartsel granite, make a discussion of their derivation but a natural third and final step. It is conceded that enormous amounts of vapor accompany volcanism, though perhaps we are apt to forget that steam has 1,700 times the volume of water, besides which the column seen over Vesuvius and other volcanoes is greatly mixed with air; the immensity of such volumes compared with solids and liquids is shown by the experiment of Gautier, who, by heating dessicated granite to 100° C., evolved from it uses 20 times, and steam 90 times, its own volume. Dana appraised the average amount of water left in ordinary rocks as 2.5 per cent. T. M. Read estimated that the Mississippi river carries to the sea annually 150,000,000 tons of rock material. If these Mississippi sediments, as deposited, contained 20 per cent. of water, it would be 600,000,000 cu. ft., or 4,500,000,000 American gallons, annually. Allowing the vapor suspended over a volcanic cone to be mixed with 80 per cent. of air, this amount of water converted into steam would replenish anew, every 9 min., a column 15,000 ft. high, 2,000 ft. in diameter at the base, and 10,000 ft. at the top. Read&apos;s estimate is only half of the amount given in a more recent and probably correct one .2

Jan 5, 1908

By A. W. Brune

Conventional methods of calculating the duty cycle of a mine hoist are awkward in that a number of items must be remembered or that they must be collected together in order to have all the calculated data in one place. A more convenient way is to tabulate all factors involved, permitting a ready evaluation of the problem. An example illustrates the convenience of such a table for either of two types of drums, cylindrical and conical. Assume the following conditions: The hoisting depth is 600 ft. Balanced hoisting is used. The weights of empty skip and ore are 6000 lbs and 12,000 lbs, respectively. Production is 3600 tons per shift. Net hoisting time per shift is six hours with a rest period of eight sec, top and bottom, per trip. Acceleration and retardation are each six sec. The diameter of the drum is seven ft; its face is four ft. The sheave has the same diameter. The equivalent effective weight of the drum reduced to rope center is 15,400 lbs. The weight of each sheave is 2100 lbs. 1 The rope is 1 1/4-in. improved plow steel weighing 2.50 lb per ft.

Jan 9, 1961