Search Documents

By J. B. Platt

Many utility fuel choices 1990-95 defied expectations, with utility decisions and coal market developments ever more closely linked. The Central Appalachian coal boom never occurred; clean-enough coal was developed in the hard-hit Midwest; Colorado-Utah coal surged; Pittsburgh seam production strengthened; utilities embraced Powder River Basin coal; and emission allowance prices collapsed. Competition drove productivity gains, but the future is not a simple repeat. Phase 2 brings fewer viable compliance options. Mega-railroad pricing has become a key risk factor -- will this be countermanded by merging utilities and power market competition? Revenue losses from vintage contracts are problematic. Uncertainty also plagues natural gas, in spite of unanimity across major forecasts, since recent experience has been so heavily influenced by the gas bubble.

Feb 24, 1997

By M. J. Little

Potgietersrust Platinums Ltd (PPRust) is Anglo Platinum?s only open pit operation. The major slope stability concern at PPRust is rapid, small-scale brittle failure on the west wall of Sandsloot open pit. In order to improve safety and mine more economically, a comprehensive slope monitoring strategy has been implemented. In the last 3 years four new state-of-the-art monitoring systems have been installed namely an ISSI microseismic monitoring system, a GeoMoS automated prism monitoring system, prismless Riegl laser scanners and a GroundProbe slope stability radar (SSR). Groundwater monitoring and visual monitoring have also been improved over the same time period. To complement the visual inspections, SiroVision digital photogrammetry is now used for predicting where future failures may occur. All these monitoring tools provide primary monitoring which is used to identify high risk areas. The SSR is then set up in that area to provide early warning of failure so evacuation can be successfully done. Fault tree analysis has proved that with this comprehensive slope monitoring strategy the geotechnical risk at PPRust is greatly reduced, allowing mining to continue safely and economically in challenging conditions.

Jan 1, 2006

THE slide-rule, as a quick and convenient instrument for performing approximate calculations, is steadily growing more and more into favour with the engineer, and results obtained by it are considered close enough to enable him to satisfactorily dealwith a considerable portion of his work. To the surveyor, however, whose ordinary computations must be as precise as his measurements, the present makes of rule are insufficient, except for a very narrow margin of the scales and for rough work. Few will carry the rule when they can clearly see that it is unreliable for general routine, and the careful surveyor is inclined to look askance at those who do use it, recognizing the temptation there undtmbtedly must be to push it into work that the log book should be called upon to treat. From the fact that a surveyor's duties take him on the surface in all weathers, and underground in many wet and uncomfortable places, where the manipulation of a book of mathematical tables becomes both awkward and patience-trying, an efficient slide-rule must offer the mbst transparent advantages. Again, a surveyor being specially trained to read divided scales quickly and accurately, the slide-rule must commend itself as an apt addition to his outfit.

Jan 1, 1912

By Daniel H. McClain

A unique partnership between the Colorado Mine Safety and Training Program (CMSTP), the Colorado Rock Products Association (CRPA) and the Higher Education and Advanced Technology (HEAT)Center resulted in a video CD-ROM training program for new miners entering the aggregate industry. Cooperation from everyone involved, including the U.S. Mine Safety and Health Administration (MSHA),made this the product against which other training materials in the mining industry will be measured in the 21stcentury. This product’s versatility and wide application make it a tool that is as critical to a mine’s success as any earthmoving machine. The state and federal grant money involved allows this product to be affordable to small operators and independent contractors. The quality of this two CD-ROM set rivals any commercially made CD-ROM training.

Jan 1, 2003

By Charles H. Jacoby

The solution mining of evaporites has a history of approximately 5,000 years. The insitu leaching of metalliferous ore will have many of the same characteristic problems which have confronted industry for years in the production of evaporite minerals. Basically we will be converting the less soluble forms of valuable metals into their more soluble salts and producing these in much the same manner as, for example, sodium chloride. There are a number of problems which we are faced with that are more complex and complicated and, therefore, will require a higher degree of sophistication than previously employed. One of our most important undertakings will be the clearcut definition of the problems involved. While a great deal of expertise can be drawn from the solution mining of evaporites and the oil industry, problems peculiar to the hydrometallurgical field will need to be solved. One of these is the introduction of permeability into an impermeable rock so as to expose the sought after values of metals which by volume are infinitesimal when compared with sodium chloride, potash or other type water soluble mineralization. After establishing this permeability which will be miniscule when compared to a solution cavity, there will be the maintenance of this permeability. In general, salt deposits are of a somewhat uniform chemical composition and thus their chemistry was relatively simple. Each metalliferous ore body is somewhat unique in its chemistry and will need to be treated accordingly.

Jan 1, 1974

Radioisotope x-ray methods for the on-stream determination of copper, lead, and zinc in mineral product slurries were developed, and were successfully tested at the plant of Cobar Mines Pty. Ltd.The tests were made in three stages. Measurements to determine the precision of analysis were made initially on briquettes of the mineral products. The effect of slurry solids content variations was then determined by measurements on the mineral products in a recirculating slurry loop. The radioisotope analyser was finally tested in a series of on-stream measurements in the plant.Copper, lead, and zinc in flotation feed and in copper concentrate were determined to a precision ranging between 1·4 and 15 per cent of the mean element concentration in the slurry solids. These precisions are within limits required for plant control purposes at Cobar.

Jan 1, 1971

By P Williams, S Flynn, R Birchfield, R Simcock, R Toft, P Comeskey

Direct transfer, or community translocation, comprises salvage and replacement of intact æsodsÆ of vegetation together with underlying soil. It has been applied to New Zealand mine sites restoration of native grasslands, wetlands, scrub lands, and forest. It is an equivalent technique to æinstant lawn or tree gardenÆ, commonly used in urban landscaping. Two to six m2 scoops of vegetation, with up to 0.7 m of soil attached, and including root plates of trees and shrubs, are relocated from stripped areas ahead of mining to sites prepared for restoration. Direct transfer uses hydraulic excavators or face shovels and dump trucks, possibly with the aid of bulldozers and other earthmoving machinery. The main advantages of direct transfer, compared with sowing or planting systems for mine site restoration, are the recycling of plant and soil materials which were often wasted by burying under overburden materials, a significantly faster revegetation process, and restoration of the whole ecosystem (plants, animals, birds, invertebrates, and microbes). The main disadvantages are higher costs of stripping and dumping, a greater degree of machine operator skill required, and scheduling becomes critically important. To illustrate the key principles, this paper gives examples of successes and failures of the technique for a variety of New Zealand mining situations. Direct transfer has been successful for a range of communities, from fern wetland and sub-alpine tussock grasslands to 5 m-tall beech forest under storey and seral shrub land, and from temperate to sub-alpine climates. Successful examples show both rapid recovery of indigenous vegetative cover and conservation of habitat for birds and invertebrates. Failures have resulted from excessive death of plants because of inadequate soil salvage depths, acidic leachates, inappropriate handling of stripped sods by inexperienced machinery operators, or prolonged drought conditions immediately following relocation. Change in plant species composition has occurred where clumps of vegetation are too far apart, or shifted plants were too small - in both cases invasive weeds have smothered the original vegetation. Changes in hydrology can also have significant impacts. Our experience indicates that the advantages of direct transfer far outweigh the disadvantages and is now used as the preferred restoration method, where practicable, at mines where it has been trialled.

Jan 1, 2000

By Dean Bray

During the past three years, a new rear-dumping dragline bucket technology has been patented, developed and tested at North Dakota coal mines. Field testing has shown that this new concept in dragline bucket technology can improve strip-mining efficiencies by reducing cycletimes and increasing dumping radius. This article details the process, participants and the results for the development of a rear-dumping dragline bucket. Participants in the process In November 1995, the board of directors of Dakota Coal authorized the execution of a field test and option agreement and a license agreement with the partnership of D.F. Schmidt, electrical/maintenance supervisor, and Bill Lengenfelder, president of Modern Industrial. The board also authorized entering into a dragline bucket field-testing agreement with the Falkirk Mining Co.

Jan 1, 1999

By José Antonio Enríquez

El presente texto describe las características estructurales y estratigráficas de los yacimientos epitermales de baja sulfuración en el corredor estructural de San Pablo en Porculla, Cajamarca. En este sentido, el corredor se relaciona a un sistema de fallas regional que tiene rumbo general NW-SW y está segmentado por fallas transformantes de dirección NE-SW, que limitan bloques estructurales. Asimismo, sobre este corredor estructural se ubican en forma alineada una serie de yacimientos epitermales del tipo baja sulfuración. Los yacimientos están controlados por fallas de dirección NW-SE y contienen mineralización en vetas y mantos con relleno de cuarzos, calcita y baritina con importantes valores de oro y oro-plata y las estructuras menores relacionadas a las fallas transformantes. Finalmente, estos yacimientos pueden constituir un nuevo e importante objetivo de exploración por minerales de oro – plata del tipo bonanza.

Sep 12, 2005

By S. M. Flaherty, R. E. Scheffel, A. Guzman

Geochemical conditions within a leaching operation are heterogeneous. This variability arises mainly from hydrological controls imparted by physical characteristics of the ore and by heterogeneous metallurgical properties at the rock-fragment and industrial heap scale. The resulting chemical conditions are responsible for stratified mineral recovery, non-uniform extraction and prolonged leach cycles. This paper presents field data from a sulfide-leaching operation which clearly demonstrate the impact of chemical heterogeneity on metal recovery and the potential use of modern measuring techniques to facilitate operational monitoring and decision making for optimization of leaching operations.

Jan 1, 2006

By Grey CA

Any economic evaluation of a lead-zinc mining project requires the estimation of net revenue per tonne of concentrate at the "mine gate". The value at the mine gate equals the Net Smelter Return minus all realisation costs. The paper develops a simple predictive model for Net Smelter Return based on metal prices.

Jan 1, 1990

By Brent Duncan, Doug Harding, Bob Stier

The 73rd Street Tunnel Project is part of “The Tunnel and Reservoir Plan” (TARP)also known as the Deep Tunnel Project, and is located in the Village of Bedford Park, County of McCook, State of Illinois. The project consists of a ø 4.42 meter × 2,060 meter long (14´-6? bore, 6,760 foot)tunnel. The completed tunnel is used as a bypass tunnel for the McCook Cup Reservoir Project. The project was awarded to Affholder Inc. of St. Louis, in 2000. The paper describes the project in which a new, high-powered open gripper type main beam machine was used in which high advance rates have been achieved using conventional muck haulage techniques. Features of the project include the installation of rock support consisting of counter-sunk rock bolts that are required to be pull-tested for strength per project specifications. Installation and testing of the bolts are done during the boring cycle. Muck haulage was done by conventional muck car train and hoisting at the construction shaft. As the site layout did not include a tail tunnel, the trains needed to be shuttled at the shaft bottom. Even with the bolting requirements and the muck haulage without a tail tunnel, the Affholder site personnel still achieved high advance rates on the 73rd Street Project.

Jan 1, 2003

By David C. Kraft

A major manufacturer and user of machine tools had the need to install a screw press machine at its plant site with the following design load requirements: (1) Vertical Compression Live Load = 2000 kip (8896 kN) and Dead Load = 1000 kip (4448 kN), (2) Rotational Moment = 6600 ft-kip (8950 kN'm). The screw press machine was to be located within an existing manufacturing building. The bottom of the footing base was located 15 ft (4.6 m) below existing floor slab. A geotechnical investigation of the site indicated a 17 ft (5.2 m) thick initial stratum of stiff to very stiff clay underlain by a 14 ft (4.3 m) thick stratum of loose to medium dense sand. Beneath the sand stratum was soft rock described as weathered shale. Obvious concern was raised on the possible effects of the dynamic motion of the screw press and potential resulting settlement within the loose sand stratum. This combination of large loads and dynamic motion resulted in the selection of a helical pile and tieback system to support the concrete foundation. The helical pile foundation system consisted of a group of vertical helical piles installed into the shale rock and a group of inclined helical tiebacks set into the remaining portion of the clay stratum. Four load tests were conducted on the vertical helical piles in order to establish compression load capacity. The results of these load tests as reported herein, led to the addition of a limited number of tubular steel push piles in order to meet the project required Factor of Safety on the design loads. All of the helical piles, push piles and inclined helical tiebacks were successfully installed and the screw press is now installed and operational.

Jan 1, 2003

By Martin Herrenknecht

Tunnel boring machine (TBM) development continues to take on not only larger diameters, but also more difficult ground conditions. Ground conditions consisting of unstable faces with water pressures up to 15 bar have required innovative design approaches. A systems approach has been required to produce tunneling machines that can safely excavate the tunnel in an efficient, cost-effective manner that stresses production and labor saving approaches. This article reviews the current design developments and present recent projects where these most recent principles have been applied. The world?s growing population and rapidly proceeding urbanization are boosting an enormous demand for new and high-capacity infrastructures to secure the mobility of goods and people. Densely populated areas face the challenge of providing efficient traffic infrastructure such as a modern public transport system. At the same time, the maintenance and modernization of supply and disposal structures for water, sewage, energy and communication are essential. Last but not least, are supra-regional transportation routes such as long distance water diversion schemes. All of these projects are as demanding and are characterized by a tight time schedule. In this context, the demand for efficient tunnels for traffic and utility lines is increasing, as new infrastructures often leads underground because of limited space above ground. Also, tunnels are the obvious choice to cross natural barriers like mountain ranges. To handle the complex and variable geological conditions and other constraints, such as low overburden, high water pressure or long tunnel drives while facing increasing demand of a quick completion of a project, mechanized tunneling sets standards regarding safety, profitability and environmental protection in traffic tunneling projects as well as in the trenchless construction of utility tunnels. Different machine types and working principles have been developed to master various geological and hydrogeological requirements. Continuous activity in research and development leads to constant improvement of the mechanized tunneling process.

Jan 1, 2008

By Tad S. Golosinski, R. Larry Grayson

Online education is not new. During the last decade, it has reached the stage where many universities offer a variety of courses, degrees and programs without any associated residency requirements. The most successful of the online universities, University of Phoenix, offers hundreds of accredited programs for close to 100,000 students throughout the world (www.phoenix.edu). Online education is considered to be a valid equivalent to traditional, classroom-based education. It is best suited to the needs of mature students with full-time jobs and a desire to deepen their knowledge. While most of the e-business has experienced severe setbacks during the last two years, e-education shows no signs of slowing down. On the contrary, the number of students and institutions offering online education keeps growing. The value of e-education associated expenditures was expected to reach $300 billion in 2001 (Sanoff,2001), making it a serious and mature industry.

Jan 1, 2002

Gas well tests were performed on 17 wells in the Roma area. The procedure used in the test programme incorporates an initial isochronal test followed by what is described as the "two flow drawdown" technique. The second flow of the two flow drawdown test was conducted for sufficient time to allow transient investigation of the surrounding reservoir. This combination of tests allows the evaluation of stabilized production capacity in addition to the determination ,of several important reservoir characteristics.It also provides a qualitative indication of reserves, by reflecting the presence or absence of reservoir boundaries within the drainage area affected during the test.

Jan 1, 1968

By P Gunn, M Watts

The general goal of passive acid mine drainage (AMD) treatment is to reduce levels of acidity and metals to acceptable levels. Most treatment systems use either an oxidising or a reducing strategy. In oxidising systems, alkalinity is added along with dissolved oxygen; in reducing systems, dissolved oxygen is removed (if present) and then alkalinity is added. It is recommended that small-scale field trials be conducted as part of the methodology of selecting the best remediation strategy at AMD sites. Following successful field trials at the Sullivan Mine AMD, the Pike River Coal Company (PRCC) has shown foresight by using the same system to treat AMD generated as a result of taking a bulk sample of coal at the Pike River coal field. The system reduced acidity by 100 per cent, iron by 99 per cent, aluminium by 96 per cent, nickel by 95 per cent, manganese by 51 per cent and zinc by 99 per cent. The success of this field trial suggests that a system using a reducing strategy may be appropriate for the Pike River Adit AMD site.

Jan 1, 2005

The concept of a magnetic hydro-cyclone is undeveloped, possibly because studies by Bragard (1965) and the Royal School of Mines in London (Robinson, 1965) were not encouraging. Its role for the concentration of ironsands is attractive in that the classifying effect within a hydrocyclone may be comparable to the classifying effect in the gravity concentration of ironsands, and thus two steps may be achieved in one. Furthermore it should be a very simple and cheap process. The idea has been explored intermittently since 1976 but more energetically since the offering of a magnetic hydro-cyclone thickener by Boxmag Rapid (1983). This paper summarises the development and test work which are detailed elsewhere (Fricker, 1984).

Jan 1, 1984

By Valérie Tremblay

Plan de la presentation ?Laboratoire d?analyse des fluids ?Gestion des contaminants ?Condition Monitoring Avantages reliés aux analyses ?En savoir plus!! ?pour minimiser les coûts d?opération; ?pour prévenir les défaillances catastrophiques; ?pour maximiser le rendement des équipements; ?pour maximiser la longévitédes équipements; ?pour permettre des périodes d?entretien planifié.

Feb 1, 2008

By G. Coombs, L. Meade, J. Welshimer

Industrial Minerals commodity profiles are continued from May's Annual Review issue. Diatomite G. Coombs, Manville Sales Corp. Growth in US diatomite production continued to lag in 1986. The US Bureau of Mines estimated that 580 kt (640,000 st) were produced last year. This is a 1%0 growth over 1985. The cumulative growth from the 1982 low point is 4.4%. Present production, though, is still only 90% of the high tonnage of 1979. The industry will see increased competitive activity with the start-ups of two new mines and production facilities in California and Oregon. US production has come primarily from Lompoc, CA, Bassalt, Clark Station, and Lovelock, NV, and Quincy, WA. New production, probably with capacities of 45 kt/a (50,000 stpy) each, have started near Burney, CA, and Vale, OR. Eagle Picher's new, full-line filter aid and filler plant at Celatom, Vale, OR, was dedicated in August. The plant uses diatomite from the Celatom mining district in Juntura, OR. Grefco's new filter aid and filler plant near Burney, CA, was ready in July. It produced flux calcined products through a single kiln and can handle both bag and bulk shipments. The operations are in Shata County with the plant and mine at the same site. Manville Specialties Group is moving its Filtration and Minerals Division headquarters and research staffs to Lompoc, CA. The move is intended to strengthen response and performance by locating research, marketing, and production close together. Diatomite is processed in three methods: natural, calcined, and flux calcined. The natural is dried to remove water and is particle size classified. Calcined or straight calcined products have been sintered to modify particle size or permeability. Flux calcination, or flux sintering, has a stronger influence on permeability and also benefits color. The unique structure of diatomite is used in a range of particle sizes from fine paint fillers, to coarser filter aids, to granular aggregates. Dimension stone L. Meade, Geomapping Associates Ltd. 1986 was another good year for dimension stone production. The trend toward using marble, granite, limestone, sandstone, and slate has created an increasing demand. According to US Bureau of Mines 1986 estimates, 1.1 Mt (1.2 million st) of dimension stone, with a value of $173 million, was produced by 200 companies. This is an increase from 1985, where 220 companies produced 1 Mt (1.12 million st) valued at $172 million. The increased production volume and decreased unit value is due to the competition from imports. The net import reliance in 1986 was 68% compared to 62% in 1985. The value of imports was $374 million in 1986 versus $295 million the year before. In an effort to maintain their market share, domestic finishers, particularly in the granite industry, continued to upgrade plants and machinery during 1986. In addition, offshore dollars have financed a number of fabricating facilities in North America that will finish imported rough stock. It is hoped that this increased domestic production capability will capitalize on a devalued US dollar. The trend has been for growth in stone usage and market. This trend is continuing with increased public awareness and desire for natural stone in buildings. The area of greatest market growth is expected to be in residential and interior decorative stone usage. Use of sophisticated, automated equipment has made the cost more affordable. Now lobbies, foyers, and specialty rooms are being clad in stone. Dolomite J. Welshimer, National Lime & Stone Co. About three-quarters of dolomite production is used as construction aggregates and 10% to 20% is sold or used as an industrial mineral. Total limestone and dolomite consumed for chemical and metallurgical purposes is about 136 Mt/a (150 million stpy). Sales of industrial dolomitic products were somewhat stronger in 1986 than levels recorded in the early 1980s. Some of the sales' strength, however, can be attributed to reductions in the number of active mining and processing operations. The industry will probably undergo further consolidation by the end of this decade. This will be due primarily to the continued softening in demand by the steel industry. Dolomitic limestone deposits being mined for raw materials for the steel, glass, and refractory in¬dustries are generally 54% calcium carbonate and 45% magnesium carbonate by weight. Impurities composed of silicon, aluminum, iron, sulfur, and phosphorous, represent less than 1%. The heaviest concentration of high purity, surface mineable dolomite in the US is in northwestern Ohio. Crushed and sized dolomitic limestone is a basic raw material for the iron and steel industry. It is also used as feed stone or lime kilns. Soft-burned lime is a popular raw material for BOF steel production. It is also used extensively in insulating glass fiber manufacturing. A related material, hydrated

Jan 6, 1987