Search Documents

By Monique Nykamp

"INTRODUCTIONTerminal 46 is located just south of downtown Seattle, and is one of the Port of Seattle’s busiest container terminals. The Terminal 46 Redevelopment Project was undertaken to replace the existing 15-m-wide (50 ft) cranes along the apron with 30-m-wide (100 ft) cranes, which can unload larger, post- Panamax ships. The project included upgrading the existing waterside crane rail with new piles and constructing a new land-side rail behind the sheetpile bulkhead. The new piles had to be installed adjacent to the existing apron without causing damage, which was a signifi cant geotechnical challenge due to the soft soil conditions at the site. An instrumentation program performed during the test pile program evaluated this challenge and allowed for the development of specifi c production pile installation procedures that had the least possible effect on construction costs and schedule.SITE HISTORYThe site lies along the west side of Elliott Bay, north of the mouth of the Duwamish Waterway. Prior to development, this area was part of the tide fl ats where the Duwamish River drained into Elliott Bay. Prior to 1970, there were several existing timber piers and structures in the area. In the 1970s, the Port of Seattle constructed a 900-m-long (3,000 ft), 30- m-wide (100 ft) apron to support fi ve, 15-m-wide (50 ft) container cranes. The contained backland area was then fi lled with dredged spoils (sand and silt with organics) and the upper 5 to 20 m (16 to 65 ft) backfi lled with sand and gravel.The existing apron was constructed using 0.4 m (16 in) octagonal prestressed concrete piles to support the precast concrete deck and crane rails. The pile-supported bents were spaced at 6.1 m (20 ft), center-to-center, along the longitudinal direction. Pile lengths typically varied from about 20 to 40 m (65 to 130 ft) with 15 to 26 m penetration below mudline (50 to 85 ft penetration). The slope below the apron was constructed at about 1.75 horizontal to 1 vertical to allow for suffi cient water depth for cargo ships. In most areas, a riprap buttress was placed at the toe of the slope. A typical cross section of the apron is shown on Figure 2.Several stability, settlement and pile driving issues arose during the original construction of T-46 (Pita, 1983). Reportedly, movement of the submarine slope occurred during pile driving, resulting in settlement behind the bulkhead. Pile driving reportedly caused settlement of adjacent piles. In addition, some piles were “running” (dropping quickly under one hammer blow) during installation."

Jan 1, 2007

By X. F. Wang, K. B. Fu

"We investigated experimentally and theoretically the adhesion behavior of Acidithiobacillus ferrooxidans (At.f6) to different copper sulfides. The adsorption experiment showed cell densities of 10.74 × 106, 8.06 × 106, 3 × 106, 4.24 × 106 and 2.35 × 106 cells/cm2, respectively, on the surfaces of djurleite, bornite, covellite and chalcopyrite. The order was: djurleite > bornite > covellite > chalcopyrite. The results indicate that A. ferrooxidans has high affinity to adhering to the surfaces of djurleite and bornite in the acidic region. But the thermodynamic approach predicts that there will be no attachment of At.f6 to the surfaces of bornite, covellite and chalcopyrite. This discrepancy is due to the inadequate description of electrostatic interactions. The DLVO approach shows attachment of At.f6 to the surfaces of djurleite, bornite and covellite, and repulsion between At.f6 and chalcopyrite. The DLVO approach can explain the differences of the adhesion of At.f6 to different copper sulfides.IntroductionThe bioleaching of low-grade copper sulfides is a developing technology, and has been applied successfully to the extraction of copper from secondary sulfide minerals (Watling, 2006; Pradhan et al., 2008; Akcil and Deveci, 2010). The bioleaching of chalcopyrite is still a major challenge (Bosecker, 1997; Brierley and Brierley, 2001; Ehrlich, 2004). A study conducted at Billiton Process Research showed the following preferential order of sulfide minerals leached by mesophilic cultures: chalcocite > bornite > cubanite > covellite > pyrite > enargite > carrolite >> chalcopyrite (Dew et al., 1999). The bacteria can solubilize the valuable metals from the orebodies by the oxidation of minerals. Bacterial adhesion plays a critical role in the bioleaching processes (Chen et al., 2008; Harneit et al., 2006). Generally, bacterial adhesion can be explained by surface thermodynamics and the extended DLVO theory, in which the adhesion energy between the bacteria and mineral is calculated as a function of the separation distance (Sharma, 1999; Bos et al., 1999; Sharma and Hanumantha Rao, 2002). These methods take into account Lifshitz-van der Waals interactions, electrostatic interactions and acid-base interactions (Busscher et al., 2010). These interactions are very well understood and formulated in mathematical equations. The most important inputs in these calculations are surface energy, surface charge, electron donation and electron acceptance on the bacterial cell surface and mineral."

Jan 1, 2015

By G. B. Abaka-Wood

"The versatility of froth flotation has made it vital in the beneficiation of rare earth elements (REE) minerals from either high or low grade ores of complex mineralogy. There has been a significant increase in the tonnage of rich iron oxide tailings obtained from extraction of primary commodities such as copper and gold in Australia, which have been identified to have very low grade rare earth oxides (REO) (= 1%). There is a vast knowledge gap in the upgrade of REO from such tailings. The aim of this research is to investigate the feasibility of the use of fatty acids for the upgrading of REO from selected iron-oxide rich tailings. Two forms of fatty acid collectors (oleic acid and sodium oleate) were employed in this investigation. Bench scale flotation tests were carried out using a Denver D-12 cell.The effects of pulp pH, fatty acid dosage, particle size distribution (-150 +75 µm, -75 +38 µm and -38 µm) and conventional depressants (sodium silicate and starch) dosage on flotation recovery of REO were investigated. A comparison of the flotation results indicated that sodium oleate was the more efficient fatty acid for REO flotation at all the pulp pH investigated. The flotation performance is demonstrated to be particle size-dependent. The results on the effect of depressants dosage indicated that both sodium silicate and starch were unselective in reducing the recovery of hematite (Fe2O3) and quartz (SiO2) with corresponding decrease in REO recovery. Generally, Fe2O3 and SiO2 formed substantial contents of the flotation concentrates obtained, both in the absence and presence of depressants, which indicates liberation is a major challenge in achieving selective REO upgrade and recovery.The flotation tests carried out on the iron-oxide rich tailings suggest the possibility of REO upgrade using fatty acids, although particle size distribution and minerals liberation are key limiting factors in achieving selective REO upgrade and recovery."

Jan 1, 2018

By H Ishikawa, R Halomoan, S Palaniandy

The Karara iron ore project is a magnetite operation consist of open pit mining and concentrator to produce high-grade magnetite concentrate. The concentrator has adopted three stages of comminution, ie fine crushing in the high pressure grinding rolls (HPGR), primary ball milling and fine grinding in the TowerMill plus magnetic separation in between these comminution devices. Since 2014, the concentrator has increased the plant feed rate by 18 per cent. Meanwhile, the ore hardness has increased by 13 per cent to a Bond work index value of 15 kWh/t that led to a coarser flotation feed. Karara Mine has decided to shift the comminution workload from the primary ball mill to the TowerMill circuit by bypassing the 100 µm fine screen in between the ball mill and TowerMill circuits. This action has increased the circuit feed particle size distribution with a top size close to 1 mm. The specific energy consumption of the TowerMill circuit was approximately 3.4 kWh/t, and the circuit product sizes (P80) were ranged between 38 and 45 µm. A joint process improvement exercise was carried out to reduce the circuit product size closer to the magnetite liberation size, ie 35 µm. Among the activities were circuit audit, recommendation for improvement, modelling and simulation, multicomponent analysis, implementation of recommendations and quantification of the improvement. One of the key findings was the density effect of multicomponent minerals in the hydrocyclone. The analysis revealed that the low density coarser gangue minerals were bypassed to the hydrocyclone overflow stream that has resulted in a coarser particle size distribution. Meanwhile, more than 20 per cent of fine (-35 µm) high-density magnetite particles were recycled back to the mill through the hydrocyclone underflow stream and increased the circulating load. Based on these outcomes, several recommendations such as conversion to bottom feed configuration, use of smaller grinding media, high operating hydrocyclone pressure and additional grinding power to the TowerMill circuit were made to improve the overall circuit performances. Karara Mine has prioritised to implement those recommendations that have a minimal financial implication. Full-scale plant trials with bottom feed configuration and 17 mm grinding media were conducted to evaluate its performances. These trials have indicated that the grinding efficiency in the TowerMill was enhanced by 10 – 30 per cent. In May 2017, all the five TowerMills were converted to the bottom feed configuration. This paper discusses the impact of shifting the comminution workload load from the primary ball mills to TowerMill circuit and the performances enhancement of the TowerMill circuit. CITATION:Palaniandy, S, Halomoan, R and Ishikawa, H, 2018. Shifting the comminution workload from the primary ball mill to TowerMill circuit, in Proceedings 14th AusIMM Mill Operators' Conference 2018, pp 163–176 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 29, 2018

By Irving Hartmann

When permissible explosives are used in coal mines according to the procedure recommended by the Bureau of Mines they are relatively safe, and no mine explosions are known to have resulted from this type of blasting. However, unsafe blasting practices - the use of nonpermissible explosives or the improper use of permissible explosives - have caused many serious disasters. In fact, such unsafe practices constitute the third most important cause (exceeded only by electricity and the use of open lights and smoking) of coal-mine explosions in the United States. During 1929-1947, inclusive, 81 explosions, resulting in 475 fatalities, were ascribed to unsafe blasting. The hazards of black powder, dynamite, and other nonpermissible explosives in coal mines have been recognized for many years, and attention has been called to this in numerous Bureau of Mines publications. Not only can these explosives ignite namable gas-air mixtures readily, but they can also ignite coal dust, as has been illustrated repeatedly in tests and at educational public demonstrations at Bruceton and elsewhere.

Jan 1, 1952

By A. C. A. Howe, J. C. Rowntree

"The Bernie Lake pegmatite near Lac Du Bonnet in southern Manitoba is a complexly zoned pegmatite containing several lithium-bearing units in addition to the western world's largest known reserve of cesium. The pegmatite forms a flat-lying ellipsoidal body within an east-west-trending Precambrian amphibolite. The pegmatite enclosed by this vertically schistose amphibolite lies near the eastern tip of a granitic intrusive. The relationship of this intrusive to the pegmatite is obscured by Bernie lake. To date, the pegmatite body has been delineated aver an area of approximately 80 acres; it attains a maximum thickness of 280 feet. Several distinct zones, including three assemblages of economic importance, comprise the pegmatite itself. The combined spodumene and lepidolite assemblages provide a recoverable defined lithium ore reserve of almost 5 million tons averaging more than 2 per cent lithium oxide. The recoverable cesium ore of the pollucite assemblage provides 300,000 tons averaging more than 20 per cent cesium oxide; this represents more than half of the western world's pollucite reserve. The Bernie Lake pegmatite deposit, owned by Chemalloy Minerals Limited, is well located with respect to the growing United States markets, and its reserves of cesium are large enough to enable it, under favourable economic circumstances, to become the major producer of this metal in North America."

Jan 1, 1967

By Ying Gu

Automated mineralogy methods and tools, such as the Mineral Liberation Analyzer (MLA) and the QEMSCAN, are now widely used for ore characterization, process design and optimization. Several case studies published recently demonstrate that large gains can be obtained through grinding and flotation optimization guided by automated mineralogy data. However, since automated mineralogy can only provide the information pointing to where the process gains can be made, it does not directly impact the production gain. Thus, a question is often asked: how to value the contribution of automated mineralogy to process improvement of a particular plant. This appears to be a difficult question. On close examination however, it is found that this is essentially a question of the value of information and it is reasonably well documented in various other industries. Hubbard (2010), in chapter 7 ?Measuring the Value of Information?, dealt with exactly this type of problem. The value of information is the reduced risk of an investment and opportunity loss. The methods Hubbard developed can be applied to estimate the value of automated mineralogy, as well as metallurgical test work, which also produces information that reduces the risk of investment. This paper first introduces Hubbard?s theory on the value of information and how to measure it. It then applies his methods to estimate the value of automated mineralogy, using Anglo Platinum?s fine grinding project as an example. In this case, the value of automated mineralogy includes the reduction in investment risk worth US$ 62.5million, in project rejection worth US$197 million and in opportunity loss worth US$320 million. In the end, a general model is developed to allow the simulation of the value of automated mineralogy in different mining operations constrained by different parameters.

Sep 1, 2012

By A. N. Shen

Fe3A1 intermetallics are potential inexpensive candidate for hot applications. In this project, torsion tests on hot-rolled and annealed Fe3A1 (Fe-15.5A1-5.8Cr-1.0Nb¬0.05C) were carried out over the ranges 750-950°C and 0.01~1s-1 . The experimental results showed that when peak stress op>90MPa (LogZ>16s-1 , Z: temperature-compensated strain rate), specimens cracked at randomly low strains. Optical microscopy exhibited original elongated grains and many grain boundary cracks associated with segregation. With op<40MPa (LogZ<16s-&apos;), specimens deformed with low random op but considerably high fracture strains; slowly propagating cracks may explain the reduced flow stress. Optical microscopy showed both elongated grains and equiaxed subgrains with some indications of geometric dynamic recrystallization (gDRX) and of static recrystallization (SRX). Compression tests gave higher stress with little effect of the preexisting cracks. The activation energy Quw of current material in satisfactory torsion and compression tests is about 10% higher than previously published. Fe3A1 has body-centered cubic structure in the experimental range, so it was compared with ferritic stainless steel 434C (Fe- 16.55Cr-0.96Mo-0.21Ni). Constitutive constants and restoration mechanism are compared between these materials. While Fe3A1 is hardly a light metal, it is considerably lighter than most steels. Furthermore, like the other body centered cubic metals (BCC) (a-Fe, ß-Ti, ß-Zr and ß-brass), it exhibits a high degree of dynamic recovery (DRV) like Al alloys, producing easier hot workability than that of austentic stainless steels.

Jan 1, 2007

By J Addai-Mensah, W Skinner, C Kelsey, J R. Kelly, E Baawuah

Comminution continues to be the most capital-intensive unit operation in mineral processing. The fundamental purpose of comminution is to liberate the valuable minerals so that they can be economically concentrated into saleable products. Declining ore quality characterised by lower grade and increased complexity requires significant energy consumption for comminution. Low-grade magnetite ores are typically fine-grained and require fine to ultra-fine grinding (P80 ~ 30 - 40 &#181;m) to enhance its liberation from the typically siliceous gangue matrix. Historically, this has been achieved using multi-stage crushing and grinding technologies, which require high energy consumption with low energy efficiency. This motivated innovations in energy efficient technologies for comminution. Such technology has been developed in the IMPTEC super-fine crusher. It is an innovative, dry (with the potential to be operated wet), media-free, energy efficient crusher that can to reduce 10 mm feed particles to 19 – 30 &#181;m with very low recycle loads. In this study, the mineralogical and physicochemical characteristics of crushed magnetite ore using the IMPTEC super-fine crusher have been investigated in comparison with those of rod milling. The super-fine crusher generated higher liberated magnetite minerals in the – 300 + 212 &#181;m and &lt; 45 &#181;m size fractions compared to rod mill. Both comminution devices generated large low-grade hematite and goethite middlings. However, the rod mill produced higher locked/unliberated hematite and goethite compared to that of the super-fine crusher. Quartz mineral had the highest liberation irrespective of the comminution device used. The super-fine crusher generated higher entrapment of other minerals within the silica matrix compared to the rod mill. The breakage mechanism of the super-fine crusher which is predominantly through high compression with shear, generated improved mineral liberation in the coarse size fractions compared to the predominant abrasion and attrition breakage mechanisms of rod milling. The higher mineral liberation generated by the rod mill is potentially due to the prolonged batch milling of the ore compared to the single-pass open circuit of the super-fine crusher.CITATION:Baawuah, E, Kelsey, C, Kelly, J R, Addai-Mensah, J and Skinner, W, 2018. Mineral liberation studies of IMPTEC super-fine crusher – 130 crushed product, in Proceedings 14th AusIMM Mill Operators&#39; Conference 2018, pp 313–326 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 29, 2018

By C. L. Coldren

Recently there has been much discussion of the use of pipelines for the long-distance transportation of solids. Many have come to recognize the economies inherent in pipeline transportation. The widespread movement of oil and gas at astonishingly low costs - a gallon of oil moves from Montana to New York for less than that for the delivery of a postcard - has spurred others to sturdy this mode of transportation. Most interested people are aware of the inherent advantages of pipelines - continuity and reliability of operations - low manpower requirements per ton mile - moderate capital costs per ton mile - low maintenance costs per ton mile - low operating costs per ton mile.

Jan 1, 1963

Discussion continuing that published in Trans.I.MIn.E ., 1915, vol.L, p.449 and 1916, vol.LI, p.166, included contributions by Smith W., McLaren R., Gibson J., McCreath W., Sneddon J.B., Kirkpatrick J. and Mowat D.M. and a written response by Black J.N.

Dec 1, 1916

By Michael J. Beus, Jan G. Patricio

INTRODUCTION The U.S. Bureau of Mines, Spokane Mining Research Center, has been conducting and documenting rock mechanics research in the Coeur d’Alene mining district for the past ten years (1, 2, 3, 4, 14, 15). A current project combines the information gathered from rock mechanics instrumentation, geologic structure, and analytic techniques to improve shaft and support design for the deep mines of the district (3). This project required knowledge of the anticipated loads and the physical properties of the rock mass to provide accurate input data for computer design models. Several techniques have been utilized to determine the physical parameters including the USGS (U.S. Geological Survey) solid inclusion probe, the CSIR (Council for Scientific and Industrial Research) biaxial and triaxial strain cells, and the CSM (Colorado School of Mines) dilatometer. This paper describes the determination of the in situ modulus of deformation in three mines over a period of three years and the evaluation of these results as they applied to this project. The need for in-situ rock mass properties such as the modulus of deformation has stimulated research and development of a large number of instrumentation techniques. One area of continuing interest involves various methods of radial borehole dilation. This concept was pursued by Menard (9) with an apparatus known as the pressure meter, which is used frequently in soil mechanics. Other developments in rock mechanics include the CPC (cylindrical pressure cell) by Panek (11) and the dilatometer by Rocha et.al. (13) in Portugal. The CSM dilatometer, which also utilizes this technique, was chosen for this project because it required a small amount of background study, was inexpensive, and could easily be combined with other experiments being planned for the test locations. Although no previous field applications to hard rock (compressive strengths greater than 20,000 psi) has been documented, the instrument was selected since good results have been achieved in granite, oil shale, and several coal measure rocks (11, 12).

Jan 1, 1977

By Robert W. Bruhn

Ground movements associated with high extraction underground coal mining, such as pillar retreat and longwall, are some- times large enough to disrupt the ground water regime as well as damage buildings and other surface structures. A U.S. Department of Energy Bureau of Mines- sponsored subsidence study at Kitt Energy Corporation&apos;s Kitt No. 1 Mine near Philippi (Barbour County) , West Virginia has provided an opportunity to monitor the ground water response above a mine panel during both developmental and pillar re- treat mining. Findings concerning ground water effects presented in this paper indicate that total extraction mining produced significant water level declines in deep-lying strata but had little effect on water levels at shallower depths. Post-mining values of hydraulic conductivity were typically somewhat higher than pre-mining values. Changes in water chemistry associated with mining were not sufficient to render the water unfit for human consumption.

Jan 1, 1986

By D J. Robinson, L L. Kuhar

"Regardless of orebody value, at some stage, the pit will reach a depth where the reward for mining wider and/or deeper is not justified by the anticipated returns. ‘Last-blast’ strategies may help to some degree in recovering additional quantities of the resource but when a pit remains, there is often significant value left in the ground. In addition, in many cases, one or many good reasons may dictate why going underground and pursuing the orebody below the pit is also not justifiable. Whereas the company can hopefully move on to other more prospective parts of the orebody, the remaining options for the pit are usually very limited. Typically the pit is either held for potentially more favourable future pit expansion opportunities or it could be used for an alternative purpose, such as tailings or waste storage. This paper will present an alternative option that involves the direct extraction of values using in situ recovery (ISR) methods to recover additional value metals from the walls and/or floor of the pit. ISR involves circulating a fluid through the remaining orebody, solubilising the target metal and subsequently returning the solution to the surface for metal recovery. ISR is not the panacea to all but it has been employed selectively in the minerals industry for some time and the production of metals, such as uranium, rely heavily on this approach. ISR is not yet considered by many operators as an approach to compete with open pit or underground mining, largely because of the perceived limitations of this approach and the perceptions of risk. Rapid recent development of tools and enabling technologies relevant to ISR have made us reconsider the most economic approach to extracting many other metals from known mineral systems, even those currently listed as subeconomic. We suggest that ISR has the potential to make mine operators rethink the end of the pit life and adopt an innovative ISR approach to work toward a more complete recovery of value metals from existing pits.Citation:Kuhar, L L and Robinson, D J, 2016. In-pit In Situ Recovery - a New Approach That May Allow for Increased Value Extraction before Pit Closure, in Proceedings Ninth AusIMM Open Pit Operators' Conference 2016, pp 275–283 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Nov 15, 2016

By L. G. Hendrickson

Direct-reduction processes for converting iron ores to metallic iron in the solid state have been available for some time; and whenever scrap becomes expensive, there is a new wave of interest in these processes. It is well established that direct reduction, coupled with electric-furnace steelmaking, is a technically viable method for making steel and in some circumstances is economically competitive with the conventional blast-furnace--basic-oxygen-process (BOP) route to steel. This raises a number of interesting questions, several of which could be of great interest to the coal and ore mining industries. For example, what are the quality requirements of the raw materials for direct-reduction--electric-furnace steelmaking? Would they be different from the present requirements for blast-furnace--BOP steelmaking? Other questions relate to how much steel will be made by the direct-reduction route in the future. The quality questions can be discussed with a fair degree of certainty, but a prediction of the amount of steel that will be produced by the direct-reduction--electric-furnace route is beyond the scope of this paper. However, an attempt will be made to identify some of the factors that will influence whether there is a swing to direct reduction and the rate at which it may occur.

Jan 1, 1978

By A. T. Adema

The cohesive zone, where the ore fed into the blast furnace softens and melts, is critical to the blast furnace performance and stability due to its influence on the gas and solid flow. This paper de-scribes a project for the development of a process model to predict the cohesive zone properties and the results of its first step; the solid flow model. The process model is expected to describe a realistic solid burden flow and the formation of the cohesive zone, its shape, location, structure, permeability, and in particular the mineralogical changes within the cohesive zone. This will be achieved using various simulation and computing tools: a combination of the Discrete Element Method (DEM) and Computational Fluid Dynamics (CFD), the DEM?CFD hybrid approach, together with models for the thermodynamics and reaction kinetics. The key benefits of the hybrid approach lie in the coupling of the continuous phase and the discrete particles, and the possibility of introducing thermodynamics and reaction kinetics into the system in a more realistic manner. Two DEM simulations are presented for a small scale blast furnace to investigate the influence of non-spherical particles on the solid flow. This influence can be observed from a more even solid flow pattern and a reduced deadman size. The results indicate the requirement to include non- spherical particles in a blast furnace simulation to achieve a realistic solid flow.

Jan 1, 2014

By Camila Lourenço Soares

A produção de aço no mundo está a cada dia mais competitivo, com isso as indústrias siderúrgicas tem desenvolvidos projetos com foco na melhoria da qualidade dos aços e na redução dos custos dos processos de fabricação. Este trabalho descreve as melhorias realizadas no processo de lingotamento contínuo, com foco na redução do desvio de placas por desobstrução dos veios da MCC 2. Esta melhoria consistiu na modificação do sistema de controle e injeção de argônio dos veios durante o lingotamento. A implementação dessas ações propiciou um melhor controle na injeção de argônio no sistema de válvula gaveta, reduzindo significativamente as obstruções do veio por deposição de alumina. Hoje, com os resultados alcançados na MCC 2 perduramos entre as melhores práticas nacionais. O trabalho foi realizado sem investimento contribuindo com a redução do custo de transformação do aço em placa.

Aug 16, 2017

By Pablo Bruno Paiva Leão

The present work is based on the characterization of nonmetallic inclusions in Ti stabilized ultra-low carbon steel, produced in a large steel mill. Due to a large incidence of submersed valve clogging in a continuous casting, the study is important in order to know the characteristics of the inclusions which are causing the problem. Total of 24 heats were sampled in the tundish and manually analyzed with a scanning electron microscope. The results revealed that 98.65% of the 3183 inclusions analyzed were solid in steelmaking temperature and 66.54% were alumina. The solid inclusions of alumina have low wettability for the iron bath, showing a high tendency of agglomeration in the submersed valves, affecting the castability. It has been concluded from the results and literature that some alternative measures such as the application of the treatment with calcium, precautions to avoid steel re-oxidation and the total or partial replacement of the pre-deoxidized element; would reduce the obstruction problem.

Oct 30, 2017

By A. A. Cochran

Bureau of MinesThe Bureau of Mines studied the development of practical methods for recovering manganese from the extensive domestic resources of low-grade ores and open hearth slags. A one-step operation was developed on a laboratory scale in which manganese and iron compounds are treated with chlorine, volatilized, and separated by selective condensation. Manganese recoveries of 90 to nearly 100 percent were obtained from 9 of the most important domestic ores. Analyses of the manganese chloride product indicated that it was suit-able for aqueous electrolysis with little additional purification. A complete, integrated process that provides for the recovery and recycling of chlorine is proposed. This process appears to have distinct advantages over previously proposed manganese recovery processes, and, in sharp contrast to leaching procedures, it is applicable to practically any manganese-bearing material.

Jan 1, 1967

By E. C. W. Perryman

Materials research and development has played an important role in the commercial success of the CANDU- PHW nuclear reactor and in the production of heavy water. Both capital investment and energy conservation demand very high component reliability in such systems. The interactions among reliability, plant performance and economics will be discussed in relation to materials research and development. Likely materials requirements for the nuclear industry over the next twenty five years will also be discussed.

Jan 1, 1977