Search Documents

By Mohammed Sakr

A Two-Section Helical Pile (TSHP) is a steel pipe with two shaft sections of different diameters and with one or more helix plates near the bottom of each shaft section. TSHPs are used regularly in western Canada as foundation pockets for single and double circuit distribution power line poles. The results of a comprehensive lateral pile load test program and the field monitoring of TSHPs installed in organic soil (muskeg) over soft clay are presented in this paper. A total of nine full scale lateral load tests were carried out, including seven tests using TSHPs with different diameters and embedment depths, and two tests using one-section helical piles. The prime objective of the study was to evaluate the lateral resistance of TSHPs installed into very soft organic soil (muskeg) overlying soft clay soils, to compare their lateral resistance relative to one-section helical piles and to compare the measured and the estimated lateral resistances using p-y curves. In order to provide sufficient soil data for analysis, the subsurface soil stratification was evaluated using two different techniques including; Cone Penetration Tests (CPT) and Portable Soil Probe Tests (PSPT). The two testing techniques were also compared and evaluated. This paper summarizes subsurface soil conditions, pile configuration, helical pile installation procedure, testing setup and results.

Jan 1, 2009

By D. F. Strong, P. P. O'Neill

"The Isle aux Morts Prospect is the first polymetallic, sulphide mineralization reported from the Port aux Basques Complex of southwest Newfoundland. Zn-Pb-Cu-Ba-Ag mineralization hosted by quartz-muscovite semipelite, occurs at the contact between a quartz of eldspathic unit and pelitic unit with intercalated amphibolite are minerals comprise sphalerite-galenachalcopyrite, in order of decreasing abundance. The principal gangue minerals are quartz, muscovite, feldspar and barite. Three morphologic types of mineralization are present: massive with more than 50% sulphide, flanked on one or both sides by disseminated and/or banded types. The massive type of mineralization exhibits a :durchbewegung"" fabric of rounded silicate fragments in a sulphide matrix, characteristic of intensely deformed and metamorphosed sulphide bodies. Sulphide minerals have been mobilized and recrystallized and share the same metamorphic and deformational history as the host rocks. Quartz muscovite schist which hosts disseminated mineralization, displays a K2O enrichment and Na2O depletion, that is typical of alteration associated with sulphide bodies in volcano sedimentary sequences. Isotopic ratios of sulphur are comparable to those of volcanogenic massive sulphide deposits.Despite penetrative deformation and metamorphic recrystallization, features of the local geology and the mineralization suggest that the Isle aux Morts Prospect is volcanogenic in origin. IntroductionFollowing the release of a government lake sediment survey (Butler and Davenport, 1980), which indicated anomalous concentrations of metals in southwest Newfoundland, geologists with Utah Mines Ltd. discovered the Isle aux Morts Prospect, a Zn-Pb-Cu-Ba-Ag showing, located approximately 15 km northeast of Port aux Basques (Figs. I and 2). The mineralization occurs in quartz-muscovite schist and is the first significant basemetal discovery in the Port aux Basques Complex."

Jan 1, 1988

By Thomas J. Witzig

This Bureau of Mines report is a background study of the International Tin Agreement. Attempts at stabilizing the tin market prior to the agreement are detailed, as well as the conditions and negotiations that set up the agreement. Details of the five consecutive 5-year agreements beginning in 1956 are presented, with emphasis on membership and the agreements' primary tools: the buffer stock and export controls, Attention is focused throughout on the United States activities during the period, especially with regard to its strategic stockpile, and its involvement with the agreement culminating in its membership, for the first time, in the fifth agreement beginning in 1976. Considerations leading to the U.S. decision to join are detailed, and U.S. activities in the negotiations for the sixth agreement are presented. The status and outlook for the agreement are discussed, and evaluations of the effectiveness of the agreement and its components are reviewed.

Jan 1, 1981

By H. M. Chikashi

Keywords: Pyrometallurgy, furnace, bath agitation, regression analysis, entrainment This paper presents the results of linear regression analysis of the influence that each component of slag has on the losses of copper in slag-cleaning-furnace slag. Data used for the analysis are actual plant data collected over the past two years of operation. Facts obtained from the study will be helpful for smelter management to control these components in the flash smelting furnace feed and slag, to levels which will enable better control of copper in slag, and smoother operation of the KCM slag-cleaning furnace.

Jan 1, 2011

By Rees J. Llewellyn

High chromium white irons can be formulated to provide required combinations of abrasion and erosion wear resistance, toughness and capability to withstand corrosion attack. As a consequence, they are used widely in casting form throughout the mining/mineral processing industry, particularly as components for slurry pumps and also as mill and crusher liners, laminated wear plates in chutes and hoppers and in valves, nozzles and cyclones. Traditional cast chromium molybdenum and high chromium white irons for wear applications are covered in ASTM A532 Classes 11 and 111 and are also available as comparable proprietary alloys. They rely on heat-treated, hypoeutectic microstructures containing a high volume fraction of very hard eutectic/secondary metal carbides and martensite to provide extremely high wear resistance. The ability to increase the carbide volume fraction and hence achieve higher wear resistance, has been limited because of severe casting difficulties encountered when carbon and chromium contents are raised and hypereutectic alloys with structures also containing coarse acicular primary metal carbides are produced. The limitation has been overcome and cast hypereutectic chromium white iron pump components have established themselves in a wide variety of mineral processing service applications. Comparisons will be made between the microstructures and wear test performance data for the various alloy types and details will be provided of the service performance improvements that have been achieved through the use of hypereutectic chromium white irons.

May 1, 2004

Power Plant. The power for the metallurgical operations is supplied by the company's own power plant, which is centrally situated. Power is also supplied to Metal Manufactures Ltd. and Australian Fertilizers Ltd., both being adjacently situated to this company'sworks.The power supplied is direct current, 250 volts, and is obtained from direct-current generators coupled to turbines and to Belliss & Morcom triple expansion engines.The steam supply is obtained from Babcock & Wilcox water tubular boilers, the fuel used being drawn from the South Coast coal mines.Transport. - The works are connected by standard broad gauge railway to both the jetties and the Government railway. Two steam and three electric locomotives are employed in this service.In addition to its own requirements, transport is provided to Metal Manufactures Ltd. and Australian Fertilizers Ltd.The various operating departments are connected by a 2-ft. gauge railway operated by Jeffrey electric locomotives.Ore Storage and Sample Mill - These departments are connected by broad gauge line to the Government railway and jetties. All material which is railed or shipped to the works from the various centres is weighed, sampled and placed in the ore store, or outside gantries, before being treated.Since the whole of the material received is either purchased or treated on a toll charge, great care is necessary in the weighing and sampling of all the receipts.Assay Oflice--The assay office is divided into several laboratories, where analyses of the various purchased materials and works samples are carried out.

Jan 1, 1938

By R. Sankey, L. Gatty, F. Bizzozero, G. F. Shannon, F. Savaglio, L. McDonald

State mining regulations in Queensland stipulate that a mine be provided with an earth installed on surface and that all underground equipment that needs to be earthed should be connected via a copper conductor to this surface grounding point. The regulations further require that all exposed metal surfaces in underground substations be connected to an earth. In a study of earthing conditions at Mount Isa mine it was found that the physical anchoring of metal work at substations (with rockbolts and associated steel mesh) also provides an excellent electrical connection to the country rock. It was established that not only is the mine's earthing system grounded at numerous underground locations but also that such anchor points offer, in general, a path to ground with lower resistance than does the legally required grounding point on the surface. It is recommended that metalliferous mines should utilise a multiple-earth system and not a run earth connected to a single, above-ground earth point

May 1, 1991

Increasing demands on quality of metallurgical grade alumina and for lower production costs led to the development of a new fluid bed calcining process. The process, jointly developed in Germany by Vereinigte Aluminium Werke A. G. and Lurgi Gesellschaften m.b.H., takes advantage of modern chemical engineering methods such as counter-current flow of combustion air and solids, direct heat-exchange between combustion air and fine solids, and near stoichiometric combustion of oil in a fluid bed. Using a two-stage Venturi-type suspension preheater for heat-recovery from combustion flue-gases, the circulating fluid bed technique with internal oil combustion at 220°F for the calcining step and a five-stage fluidized bed cooler for heat-recovery from calcines, the process gives an outstanding heat-efficiency. In a first industrial plant for 560 sh. tons/day of alumina heat consumption figures of less than 1·400 B.T.U./lb Al203 g were achieved.

Jan 1, 1972

By Finlayson EJ

New detailed mapping, micropalaeont- ology and isotopic dating have been successful in revising the stratigraphy of Woodlark Island. All Middle to Late Miocene intrusives and volcanic rocks have been assigned to the Okiduse Volcanics. In addition, the results demonstrate that the Tabukui beds and Wonai Hill beds (N9, late Early Miocene to earliest Middle Miocene) are a single unit. Similarly, the Nasai and Suloga Limestones are confirmed as a single stratigraphic unit as they yield similar foraminiferal ages (upper Te, Early Miocene), and both occur in the same stratigraphic position unconformably overlying basement Loluai Volcanics. Radiocarbon dating suggests a latest Pleistocene age for the upper Kiriwina Formation. Extensive Quaternary cover and low relief prevents detailed structural airphoto interpretation. In general, the structure is simple with all units on Woodlark dipping to the northwest a_4 exhibiting prominent local block faulting.

Jan 1, 1991

By C. H. Schack

Extractive metallurgy techniques currently employed to recover silver from primary ores and secondary scrap were reviewed and evaluated to identify and delineate metallurgical problems whose resolution would increase the supply of silver from domestic materials. The survey revealed that practically all primary silver is recovered by froth flotation concentration of various types of ores, followed by smelting and refining of the separate lead, copper, and zinc concentrates. Silver losses during the complex processing are, with rare exception, inconsequential. Furthermore, any silver production gain from base metal ores, which contribute about two-thirds of the total primary silver, is directly dependent no improvement in the market for the base metals. Statistical data on new and old silver scrap are wholly inadequate to make reliable conclusions about scrap processing problems and the possibility of increasing the recovery of silver from the many forms of secondary silver-bearing materials. The available information indicates (1) that efficient silver reclamation practices are employed by the larger users of silver, and (2) that recovery of additional secondary silver involves solution of problems of collection rather than of processing. Several possibilities exist for limited increases in silver production from primary ores by improvement in metallurgical practices. Specifically, research is needed to (1) solve the problem of recovering silver from the copper ores of the Copper Range district, Michigan; and (2) devise economically feasible methods for recovery of silver from presently marginal or submarginal ores char because of grade, location, and frequently complex nature cannot presently be exploited by conventional techniques.

Jan 1, 1965

By R. Schulz, K. King

Concentrating Line 6 just went down again. The control room operator checks the graphic display. Only one piece of equipment shows an alarm. Clicking on the ball mill icon, he discovers the culprit was the low flow lube switch. The flow looks okay now, but it is the third time this week the switch has stopped the line. Maintenance is called, the switch replaced and the line is up running again. Sending the right person to the right spot immediately can save hundreds of hours of downtime every year. This paper discusses the principles behind implementing smart First-Out Fault Detection to dramatically reduce equipment downtime in new, or existing control system architectures. Methodologies are presented to maximize the system benefits, while minimizing development costs. Case histories are presented for a number of successful implementations in mineral processing plants.

Jan 1, 2001

By J. H. Holden

Operations involving the processing of coal, oxygen, and steam into synthesis gas by means of two pressure-type gasifiers have demonstrated the effect of heat loss and operating variables on carbon gasified and oxygen and coal requirements. Carbon gasified is the fraction of carbon in the coal that is converted to gas. Oxygen and coal requirement is the quantity of each that is needed to produce a unit volume (M std. c.f.) of carbon monoxide and hydrogen. Operating pressure of the gasifiers ranged from 150 to 300 p.s.i.g. and coal was fed at 200 to 500 lb./hr./cu.ft. of reaction-zone space. Oxygen-to-coal ratios were 8.5 to 10.5 std. c.f./lb. Heat loss and residence time have opposite effects on carbon gasified; increasing the heat loss decreases the carbon gasified, but increasing the residence time (by raising the operating pressure or reducing the coal-feed rate) increases the carbon gasified. The effects of these two factors are difficult to separate because they usually change simultaneously. A comparison of the results obtained from the operation of two gasifiers with different levels of heat loss, however, permitted the effect of heat loss to be separated from that of pressure and coal-feed rate. When the results were deter- mined on the basis of constant heat loss, increase of the residence time increased the carbon gasified until the reaction virtually had come to completion. For example, at 150 p.s.i.g., decreasing the coal-feed ratio from 500 lb./hr./cu.ft. to 200 lb./hr./cu.ft. substantially increased the carbon gasified. At 300 p.s.i.g., however, changing the coal-feed rate had little effect on the carbon gasified because the reaction had almost reached completion and further increase in residence time resulted only in a negligible change.

Jan 1, 1962

By H. T. Chiwaye

Risk analysis is an important step in the design of rock slopes in open pit mining. Risk is defined as the product of the probability of slope failure and the consequences of the failure, and is generally evaluated in terms of safety and economic risk. Most of the risk analysis done at present is based on the use of limit equilibrium (LE) techniques in evaluating the probability of failure (POF) of the slopes. The approach typically makes use of full Monte Carlo simulations of the limit equilibrium models, with all uncertain variables randomly varied. The number of required simulations is generally over a thousand, at times as high as 20 000, in order to produce statistically valid results of the POF. Such an approach is clearly not practical when using numerical modelling programs dueto the high computational effort required. This paper explores the impact of using numerical modelling instead of the traditional LE techniques in evaluating the probability of slope failure. The difference in the overall assessed risk, in terms of economic impact, for the mining operation is then evaluated. With numerical models, approximate methods are used in the calculation of the probability of failure instead of full Monte Carlo simulations. This paper will use a method called the response surface methodology (RSM) for estimating the POF from numerical analyses. Simple slope models were used to verify the accuracy of the RSM method by comparing the results with those obtained from full Monte Carlo simulations. It is shown that there is good agreement between the POF values computed using full Monte Carlo simulation and those obtained using the RSM method. Finally, the use of numerical modelling in the assessment of risk is shown to bring a significant difference in the result compared with that from LE methods. One of the reasons for the difference is that LE models tend to underestimate the failure volumes and hence the consequences of slope failure.

Jan 1, 2010

Duty on Lead Reduced. -On December 28, the President signed H.R. 5047 which reduces the duty on unwrought lead from 3.5% ad valorem to 3% ad valorem, with a floor level of 1.0625 cents per pound, effective retroactively from January 1, 1980, through June 30, 1983. Pacific Northwest Power Bill Passed. -On December 5, the President signed S. 885 which will enable the Bonneville Power Administration to guarantee 20-year contracts to its 15 major industrial customers in exchange for higher rates. In effect, the bill will have industrial customers pay some of the costs of building additional generating facilities in the Northwest, of which thermal units are expected to be a major part. BPA supplies power to six primary aluminum producers which operate eleven plants having over 30% of the primary aluminum capacity in the United States.

Jan 1, 1980

Five watersheds, ranging in size from 29 to 49 acres, were selected in East-Central Ohio to investigate the hydrologic and water quality conditions occurring before, during, and after surface mining. Four of the watersheds will undergo surface mining, involving either the Number 6, 9, 11, or 8 coal seams, and one watershed having an outcrop of the Number 6 coal will be operated as a control watershed. To determine the premining hydrologic and water quality conditions (Phase 1), physical information was obtained for each watershed and instrumentation was installed for obtaining hydrologic data and water quality samples. In addition to topographic maps, soils and vegetation maps were prepared. Stratigraphic columns were developed from geologic cores; networks of observation wells and of soil moisture access tubes were installed; and weather stations were established to measure temperature, humidity, wind and solar radiation, and to collect precipi¬tation samples. Field data were collected over a 10-month period for one watershed and for about 8 months on another watershed before surface mining began. The other watersheds continued in the premining data phase. These data were for precipitation, temperature, relative humidity, wind speed, solar radiation, snow and frozen soil, soil moisture, infiltration (rainfall simulator), spring discharge, runoff from watersheds, and ground-water levels. Also, samples of runoff and ground water were obtained for chemical analyses and additional samples of runoff were acquired for suspended sediment load determinations. Over the study period, precipitation was not very representative of the long term averages, but data are available from the control watershed for a representative 7 year period which should prove invaluable in modeling the hydrology of the project watersheds for the premined conditions. Spring discharges (before mining) from the upper aquifer of two of the watersheds averaged only 508 and 652 gallons daily. The proportion of precipitation occurring as surface runoff from the large watersheds ranged from 8 to 36 percent and the peak discharges from 5.86 to 81.95 cfs. Base-flow and runoff water samples from four of the watersheds (unmined conditions) were collected and analyzed quantitatively for 39 water quality parameters. Monthly precipitation samples sediment fractions of the base flow and runoff were analyzed for 22 and 17 parameters, respectively. The average concentrations of the water quality parameters for the watersheds (unmined), except for suspended solids, were as low or lower than the EPA recommended maximum allowable concentrations in drinking water. Several parameters in precipitation equaled or exceeded the levels of corresponding parameters in runoff water. The average concentration of suspended solids in storm runoff ranged from 118 to 1110 mg/l, and for base flow the range was from 44 to 247 mg/l; the higher concentrations were associated with the watersheds exhibiting the greatest disturbance. Iron ranged from an average of less than 3 µg/1 to 228 µg/1. Manganese ranged from less than 41 µg/1 to 334 µg/I. Ground-water systems (unmined condition) are described for the five project watersheds. Each watershed was found to have two major perched aquifers within the top 250 feet. Generally, these perched aquifers involve local flow systems, though flow across watershed boundaries in some areas. Recharge is mostly from local precipitation and discharge is mostly as spring flow, base flow, evapotranspiration, and leakage through the underlying confining bed. Shallow ground water was commonly of the calcium bicarbonate type. Although dissolved-solids concentration was generally 200 to 600 mg/1, brackish or salty ground water was present in several areas. A composite hydrologic model for the project watersheds will consist of separate ground-water, unsaturated flow, overland flow, and evapotranspiration component models. The ground-water model (a modified quasi-three--dimensional U. S. Geological Survey model) operates on a grid network and the newly formulated unsaturated flow model was divided into overlying prismatic elements for numerical solutions. The unsaturated flow model includes provision for incorporating the evapotranspiration model. An available distributed kinemetic overland flow model was utilized. An analyses was made of one of the costs of reclaiming coal mines; the legal and administrative costs of complying with legislation. Such costs borne by coal companies under the Ohio law are thought to be a surrogate of these costs under the new Federal law. Regression analyses were used to relate the legal and administrative costs to acres in the permit and the tonnage of coal produced.

Jan 1, 1978

The Rosebery and Hercules mines, situated in the Rosebery-Williamsford district in western Tasmania, have a history of production dating back to 1896-7, although full scale production did not commence until 1936, following the development of a satisfactory process of selective flotation (Hall, Cottle, Rosenhain and McGhie, 1953). The mineral composition of the Rosebery zinc-lead ores was first described in detail by Stillwell (1934). The Hercules ore is generally similar, but as yet no descriptions of it have beenpublished.Since Dr. Stillwell's paper appeared, the management of the Rosebery and Hercules mines has from time to time submitted a number of interesting mineral specimens to C.S.I.R.O. Mineragraphie Investigations. Examination of these specimens brought to light eight minerals, some relatively uncommon, not previously recognized in these ores.They are cassiterite, molybdenite, stannite, electrum, meneghinite, boulangerite, pyrargyrite and pyrrhotite. Some of the specimens are also rich in tetrahedrite and gold. In addition each of the other ore minerals described by Stillwell, viz. pyrite, sphalerite, galena, bournonite, chaleopyrite and arsenopyrite, was detected in one or more of the specimens examined during the present study. The principal gangue minerals were found to be quartz, manganiferous carbonate, sericite and barite, agreeing closely with the observations of Stillwell.The present study was based on the examination of the following eight specimens.

Jan 1, 1960

By Beverly Cramp

In 1995, mining engineer Alain Gachet thought about using Earth-observation satellite imagery to search for precious minerals. The latest radar Earth-observation satellite, Canada’s RADARSAT-1, had just been successfully launched at the time, creating new opportunities for commercial applications. Gachet was working in Congo Brazzaville as an oil executive and general secretary of Elf Congo for the French national oil company Elf Aquitaine. He understood that the RADARSAT-1 launch promised new and cost-effective sources of data for mineral and oil exploration. “It was early 1996 before I ordered my firstRADARSAT-1 satellite images,” said Gachet. “I was first struck by the quantity of information delivered by the radar images. Linear structures and faults were clearly defined and subtle topographic features were tremendously enhanced,” he said. “It was ‘tree top geology,’ but this kind of information appeared to be key for finding new gold seams.”

Jan 1, 2003

By Oliver Bowles

"INTRODUCTION Slate has earned a high reputation as a roofing material, carefully selected and properly placed it is rainproof, attractive, and extraordinarily durable. Despite there qualities in its favor, the slate industry during the past 30 years has suffered marked reduction in volume of sales. An increase in building construction and general improvement in business will doubtless bring renewed activity, but considerable ground has to be recovered before the industry can become prosperous. Influences tending to dwarf this long-established industry producing materials of world-wide reputation are analyzed briefly in the following pages in the hope that they may be rectified.HISTORY OF SLATE PRODUCTIONFigure 1 shows graphically the rise and fall from year to year of sales of roofing slate since 1885. In quantity, the peak was reached in 1902, and the most serious decline was from 1912 to 1918, sales at the end of this 6-year period being only one third those at the beginning. Unlike most building materials, slate experienced only a slight recovery in volume of sales during the post-war period, 1920-29. The value closely parallels the volume up to the World War period. Subsequently, however, as unit values increased the aggregate value rose sharololy above the volume curve, attaining in 1928 the point reached in 1903, although the Lumber of squares sold was scarcely one third as great. The increased unit value was due partly to larger sales of heavy architectural grades."

Nov 1, 1933

By M. R. Geer, H. F. Yancey

"INTRODUCTION Throughout the history of coal washing, the jig has been one of the most important coal-cleaning appliances. In 1935 34.7 percent of the 45,361,021 tons of clean coal produced was the product of jigging. 4/ Previous to 1928, most of the jigs used in the United States were of the piston type, with which sufficient mobility to allow stratification in bed is imparted by the reciprocating up-and-down movement of a piston in the water compartment adjacent to the screen compartment. In 1928, the Baum type of jig was introduces in this country and has since come into wide spread use. In this type, water pulsations are imparted by application and release of compressed air to the water compartment. All prior studies of the mechanism of seperating cleared coal from impurity by piston-type jigs. 5/ The same laws of settling, of course, apply to both types, piston or Baum, but the character of the separation with the Baum type may be modified more easily because of the flexibility with which air may be handled, as distinguished from the fixed action of eccentrics commonly used in piston jigs. Since no detailed studies are available to show the performance, that is, the character of the separation between coal and impurity, of the Baum type the Bureau of Mines undertook the investigation recorded in this report."

Jan 1, 1938

By D Macdougall, J Otto

The financing of large mining projects in developing countries is often achieved, at least in part, by limited-recourse financing methods. Financing agreements are affected by the basic accord that is struck between the host government and the sponsors of the project. It is concluded that governments and project sponsors should take into account the requirements of lenders when structuring such mineral development agreements to maximise the potential for attracting project financing. Lenders are likely to be most interested in aspects such as fiscal arrangements, calculation of taxable income and general accounting rules, royalties, transferability of payments/dividends overseas, corporate structure and control, staged development, financing, loan support and state guarantees/approvals, political risk, provisions for default, product marketing, settlement of disputes and environmental issues

Aug 1, 1994