Search Documents

By Olgac Kangal, Ali Guney, Gulay Bulut, Guven Onal, Ayhan A. Sirkeci

This paper presents the results of pilot scale column flotation applications in the two different copper concentrators in Turkey. The Kure Copper Plant is located in the Black Sea Region of Turkey. In Kure, a very fine grinding requirement for an adequate level of liberation makes a successful flotation difficult and consequently the final concentrate can hardly assay above 16% Cu Column flotation tests were conducted at the plant site using two different column types The experiments proved that the grade of the concentrate could be increased from about 14% Cu to 25-26% Cu. Murgul Cakmakkaya Copper Concentrator is the largest copper concentrator in Turkey. Although concentrate production capacity is around 170,000 tons annually with 22-23% Cu content, this figure tends to be much lower than that. In Murgul a Turbo Column of Multotec Company of South Africa was employed. As a result of systematic column flotation tests, the grade of the concentrate was increased from 20.3% Cu to 28.7% Cu.

Jan 1, 2003

By J. Autio, H. Malmlund

The excavation damage zone (EDZ) caused by drill and blast excavation consists of intense damage adjacent to the remaining half barrel of the blast hole, new fracturing induced by the blast and reactivation of pre-existing fractures. The properties of intense microfracturing adjacent to the half barrels of remaining blast holes are based on study of rock samples from ZEDEX-tunnel and it’s extension at Äspö and the Research tunnel at Olkiluoto in Finland. The new and reactivated fracturing is based on results of mapping of slots cut in the rock in ZEDEX-project. The zone of increased porosity adjacent to half barrels, which penetrates to a depth of some centimeters was studied by using novel 14C-PMMA method. The penetration of the radial fractures, which is an order of magnitude deeper, was studied by mapping using color penetrant. Results of EDZ studies carried out at Äspö HRL in Sweden and in Research Tunnel at Olkiluoto show that the properties of EDZ can be affected significantly by engineering design. The result imply that the additional pore volume caused by distinct fracturing around the blast holes caused by state-of-the-art smooth blasting technique could be of the same order as that of the damaged zone adjacent to the surface of the half barrels. Durch Bohr- und Sprengarbeiten entstandene Eigenschaften der Auflockerungszone: Die durch Bohr- und Sprengarbeiten entstandene Auflockerungszone besteht aus einem großen, an das Resthalbrohr des Bohrloches angrenzenden Schaden, neuer Rissbildung und einer Reaktivierung der bereits existierenden Risse. Die Eigenschaften einer immensen, an die Halbrohre der Restbohrlöcher angrenzenden Mikrorissbildung beruhen auf einer Studie über die aus dem ZEDEX-Tunnel gewonnenen Gesteinsproben und deren Fortsetzung im Untertage-Labor Äspö (Hard Rock Laboratory, HRL) in Schweden und im Forschungstunnel bei Olkiluoto in Finnland. Die neue und reaktivierte Rissbildung basiert auf den Auswertungsergebnissen der Schlitze, die bei dem ZEDEX-Projekt ins Gestein geschnitten wurden. Die Zone der vermehrten, an die Halbrohre angrenzenden Porösität, die in ein paar Zentimeter Tiefe eindringt, wurde anhand der neuen 14C-PMMA-Methode untersucht. Das Eindringen der etwas tiefer gelegenen radialen Risse wurde anhand eines farbigen Eindringungsmittels untersucht. Die in Äspö und Olkiluoto durchgeführten EDZ-Studien zeigen, dass die EDZ-Eigenschaften wesentlich durch Engineering Design beeinflusst werden können. Das durch Bohrarbeiten verursachte Hohlraumvolumen der Rissbildung um den Tunnel herum ist ähnlich wie das Hohlraumvolumen der Bruchzone um die Bohrlöcher herum. Caractéristiques d’une zone endommagée par le creusement résultant d’un creusement par forage et dynamitage: La zone endommagée par le creusement résultant d’un creusement par forage et dynamitage présente un endommagement intense adjacent au demi-cylindre restant du trou de mine, une nouvelle fracturation et la réactivation des fractures préexistantes. Les caractéristiques de la microfracturation intense adjacente aux demi-cylindres des trous de mine restants reposent sur l’étude des échantillons de roche en provenance du tunnel ZEDEX et de son extension au laboratoire souterrain d’Äspö (« Hard Rock Laboratory » ou HRL) en Suède et du tunnel de recherche d’Olkiluoto en Finlande. La fracturation nouvelle et réactivée repose sur les résultats du placement des rainures sur la roche dans le projet ZEDEX. La zone de porosité accrue adjacente aux demi-cylindres et pénétrant à une profondeur de quelques centimètres à fait l’objet d’études recourant à la nouvelle méthode 14C-PMMA. La pénétration des fractures radiales, considérablement plus profondes, a été étudiée par placement en utilisant un agent pénétrant coloré. Les résultats des études EDZ effectuées à Äspö et à Olkiluoto montrent que les caractéristiques de l’EDZ sont susceptibles d’être affectées de manière significative par la conception technique. Le volume vide de fracturation résultant du dynamitage autour du tunnel est du même ordre que celui de la zone concassée autour des trous de mine.service.

Jan 1, 2003

By J. Walker, G. E. Kim

Since May of 2000, Mogas Industries, in partnership with F.W. Gartner Thermal Spraying Co. and using the services of Perpetual Technologies, has invested time, energy, and resources towards developing novel ball valves for high-pressure acid-leach (HPAL) service. In addition to developing new valve designs, an aggressive coatings development effort has been undertaken to improve the protective quality of the coatings so as to enhance the performance and extend the life of valves in severe HPAL conditions. In 2001, Mogas Industries qualified and applied a nanostructured titanium oxide (n-TiO2) coating for gold and nickel/cobalt HPAL services. The n-TiO2 coating provided dramatically superior protection against abrasive and erosive wear, fared very well against high-pressure autoclave corrosion testing, and has performed well in HPAL service.

Jan 1, 2004

By A. N. Fried

One of the important problems confronting oil producers in appraising the possibilities of secondary recovery in many California fields is the effect of viscosity on oil recovery by water flooding. In January 1954 there were 554 fields and/or pools, in the State, that produced 1 million barrels daily, and 138 of these pools produced approximately 267 thousand barrels daily of heavy crude oil having gravities below 200 API. Many of these fields are nearing the end of their primary economic life and still have high residual-oil saturations, a favorable factor in water flooding. The crux of the problem is whether or not enough oil can be recovered from these fields by water flooding to make the operation economically successful. Some experiments on the relationship between viscosity and oil recovery have been made by other investigators, but in most instances the viscosity of the oils used in the experiments was lower than the viscosity of the oils found in many of the heavy-oil fields in California. A study was undertaken, therefore, to determine the relationship between oil viscosity and recovery over a wider range of viscosities and to compare the experimental results with those predicted by theoretical calculations.

Jan 1, 1955

By Lewis M. McNay

The Bureau of Hines and industry (mining and private) have studied the placement of hydraulic sandfill in deep-vein mines to identify existing problems and to develop techniques to strengthen the support characteristics of the sandfill. The hydraulic sandfill system, physical properties of typical classified mill tailings, and properties of sandfill modified by various techniques are discussed. Computer analysis has defined the support capability of various sandfills using actual mine field data as a reference base. High-modulus sandfill can provide adequate support in deep-vein mines to alleviate rock and pillar stresses and to reduce rock-burst incidence.

Jan 1, 1975

By W. T. Westbrook

This Bureau of Mines report contains methods for analyzing iron are for total iron, ferrous iron, metallic iron, silica, manganese, aluminum, calcium, magnesium, phosphorus, titanium, carbon, sulfur, moisture loss, and ignition loss by wet chemical methods. Some are modifications of standard umpire methods; others have been developed by the Bureau of Mines to provide a com-bination of speed and accuracy. They are suitable for a high volume of samples and/or control situations, and for situations in which instrumental results must be verified. These methods have been used to analyze taconites, native ores, some foreign ores, and metallurgical products.

Jan 1, 1975

By Rodrigo Rangel Porcaro

Desenvolveu-se um dispositivo para soldagem por gravidade com eletrodos revestidos e investigou-se o comportamento do dispositivo em função de variações nas condições operacionais. Ciclos térmicos durante a deposição de cordões em tubos de aço API X65Q foram avaliados por meio de medidas experimentais, utilizando-se termopares inseridos na poça de fusão durante a soldagem por gravidade. Amostras do metal base e do cordão depositado em diferentes condições de aporte térmico passaram por análise química, microestrutural e metalográfica. Observou-se boa repetibilidade na velocidade de deposição do dispositivo e aspecto visual adequado de cordões de solda depositados. Os resultados dos ciclos térmicos mostram que as variações nos valores de ?t800/500, utilizando eletrodos AWS E7018 e correntes de soldagem de 70A e 150A, causaram redução de 21% na proporção de ferrita acicular e, consequente, redução de 22% nos valores de microdureza do metal de solda com maior aporte térmico.

Oct 30, 2017

By D. L. Katz, M. J. Rzasa

The derivations of three methods of computing the static pressure gradients in natural gas wells have been presented to show the assumptions made. Charts were developed from which the pressure gradients may be read when the well-head pressure, the well fluid gravity, depth, and the average well temperature are given. A chart for estimating the well fluid gravity from the condensate content and separator gas gravity is included. The effect of the increased average well temperature after flow on the calculation of the static pressure gradient is discussed. Introduction Reservoir pressures have been calculated from well-head pressures for gas wells for many years. As the pressure measurements become more accurate, the need for a reliable calculation of the static pressure gradient often arises. This paper will develop the several methods for computing the pressure gradient in gas wells and make a comparison between them. The method of calculating static pressure gradients in common use is Eq. I (ref. I) or its counterpart which includes a factor for the deviation of the gas from the ideal gas law. P2 - P1 = P1(e0.0000347GX _ I) Eq. [I] in which P1 = pressure at well head, lb. per sq. in. abs. PP = pressure at bottom of well, Ib. per sq. in. abs. G = gas gravity X = depth of well, ft. An alternate method is to compute the average density of the gas in the well and multiply by the well depth in a manner similar to that used for liquid gradients. Derivation of Formulas A static pressure gradient is a special case of the general fluid-flow equation. Consider a pound of fluid flowing in a vertical column from point I to point 2, Fig. I. By an energy balance for fluid flowing from I to 2: U1 + P1V1 + u12/2g + X1 + q = U2 + P2V2+ u22/2g+X2 +W [2] in which U = internal energy, ft-lb. per lb. P = pressure, lb. per sq. ft. V = volume, cu. ft. per lb. u = average linear velocity, ft. per sec. X = height above datum, fl. q = heat absorbed by fluid, ft-Ib. pcr lb. W = work done by system, ft-lb. per lb. An energy balance on the fluid itself gives: U = ?TdS - ?PdV + etc. [3] in which T = temperature, deg- R- S = entropy, ft-lb. per deg. R. per lb.

Jan 1, 1945

Reduce the potential of haulage related injuries in underground mines by providing a method for quickly assessing the state of repair of mine haulage track. The Problem Currently, there are no established standards or procedures for inspection or cleaning of underground mine haulage track. Many track defects are hidden from an inspector because of layers of dirt and debris on the ballast, spikes, fishplates, etc. When a visual inspection can be performed, it may be highly subjective, except for a few items that can be categorized or counted, such as missing bolts or spikes. Track inspectors may even become tolerant of defects that can gradually worsen. For these reasons, mechanical inspection methods are needed to supplement visual inspections. Approach The Bureau investigated this problem and designed a towed vehicle to both mechanically clean and inspect underground coal mine haulage track. The vehicle was developed using a systems approach, paying particular attention to human factors issues such as operator field of view, operator ingress-egress, control positioning, and seating design. The prototype was built using simple fabrication techniques and off-the-shelf components.

Jan 1, 1990

By Elmer Evangelista S

El objetivo del texto es difudir los avances científico-tecnológicos en las fases de prospección-exploración-explotación de los recursos marinos mineros del Perú a través de una recopilación de datos estructurados en diagramas, documentación fotogeológica, análisis y planos, los cuales permitirán evaluar el potencial de los depósitos del piso oceánico y tecnológico que se posee en la actualidad.

Nov 20, 1978

By Charles Austin

IT has been known for several years1 that certain alloys of the Konal type, containing commercial cobalt (99.32 per cent C0 and 0.42 per cent Ni) and varying amounts of ferrotitanium, exhibit very high tensile strengths at 600°C. However, their pro-portional limits and yield points are rela-tively low. Published data1 for the alloys quenched in water from 950°C. and then tested at 600°C. are summarized in the upper section of Fig. I. Similar specimens that were aged at 650°C. for 72 hr., after quench and prior to testing at 600°C., gave the results shown in the lower section of Fig. I. TABLE I.-Analysis of Material I Percentages Constituent Sample Sample Sample 3125 3124 3123 Si 0.25 0.51 o.6o Fe 4.15 10.70 13.17 Ti I.15 3.58 4.70 Mn 0.30 0.41 0.42 Co (by difference)^ 94.15 84.80 81.71 The cobalt from all three samples, united and tested for nickel, gave 0.54 per cent Ni based on the weight of cobalt. In the present work the investigation of the properties of these materials has been extended by a study of the tensile deforma- tion characteristics in moderately long-time tests at 600°, 700° and 800°C. after quenching from various solution tempera-tures. In addition, some metallographic studies have been made to correlate with the deformation tests, and to obtain in- FIG. 1.-EFFECT OF VARYING AMOUNTS OF FERROTITANIUM (FE2TI) ON PHYSICAL PROPER-TIES OF COMMERCIAL COBALT. (C. R. Austin.1) Upper section. Tested at 600°C. after water-quenching from 950°C. Lower section. Tested at 600°C. after water-quenching from 950°C. and aging 72 hr. at 650°C. FIG. 2.-PORTION OF QUASI-BINARY DIAGRAM COBALT-FE2TI AS DETERMINED METALLOGRAPH-ICALLY. formation on the quasi-binary system Cobalt-Fe2Ti. The material, very kindly furnished by the Westinghouse Electric and Manufac-turing Co. in the form of hot-swaged rods of 3/16-in. diameter, analyzed as shown in Table I. The alloys, when originally made up,1 were based upon an iron-titanium com-pound, Fe3Ti, as indicated by the work of

Jan 1, 1940

By Herbert Clark Hoover, Lou Henry Hoover

GEORGIUS AGRICOLA was not only the author of works on Mining and allied subjects, usually asso ciated with his name, but he also interested himself to some extent in political and religious subjects. For convenience in discussion we may, therefore, divide his writings on the broad lines of (1) works on mining, geology, mineralogy, and allied subjects; (2) works on other subjects, medical, religious, critical, political, and historical. In respect especially to the first division, and partially with regard to the others, we find three principal cases : (a) Works which can be authenticated in European libraries today ; (b) references to editions of these in bibliographies, catalogues, etc., which we have been unable to authenticate ; and (c) references to works either unpublished or lost. The following are the short titles of all of the published works which we have been able to find on the subjects allied to mining, arranged according to their present importance :-De Re Metallica, first edition, 1556; De Natura Fossilium, first edition, 15,46 ; De Ortu et Causis Subterraneorum, first edition, 1546; Bermannus, first edition, 1530 ; Rerum Metallicarum Interpretatio, first edition, 1546; De Mensuris et Ponderibus, first edition, 1533; De Precio Metallorum et Monetis, first edition, 1550 ; De Veteribus et Novis Metallis, first edition, 1546; De Natura eorum quae Effluunt ex Terra, first edition, 1546 ; De Animantibus Subterraneis, first edition, 1549. Of the " lost " or unpublished works, on which there is some evidence, the following are the most important:-De Metallicis et Machinis, De Ortu Metallorum Defensio ad Jacobum Scheckium, De Jure et Legibus Metallicis, De Varia Temperie sive Constitutione Aeris, De Terrae Motu, and Commentariorum, Libri VI. The known published works upon other subjects are as follows:-Latin Grammar, first edition, 1520; Two Religious Tracts, first edition, 1522; Galen (Joint Revision of Greek Text), first edition, 1525 ; De Bello adversus Turcam, first edition, 1528 ; De Peste, first edition, 1554. The lost or partially completed works on subjects unrelated to mining, of which some trace has been found, are:-De Medicatis Fontibus, De Putre¬dine solidas Partes, etc., Castigationes in Hippocratem, Typographia Mysnae et Toringiae, De Traditionibus Apostolicis, Oratio de rebus gestis Ernesti et Alberti, Ducum Saxoniae.

Jan 1, 1950

By J. Mark Richardson

The use of an integrated software package to simulate and optimize the performance of mineral processing circuits is illustrated by three examples. Each represents application of the software and associated techniques to optimization of an existing plant. In the first example, a South-western U. S. copper company employs the method to simulate and improve performance in crushing, screening and SAG milling. A second copper producer evaluates equipment changes and flowsheet alternatives in a closed-circuit ball mill-cyclone operation. A Southeastern U. S. aluminum refinery optimizes performance of a dry milling and classification circuit for production of carbon particles used in anode casting. Graphical and tabular data describe the circuits simulated and the results achieved in each example.

Jan 1, 1990

By I. H. Pratt

The results of a study on the preparation of thin-film capacitor structures are discussed. The dietectric source material was quartz which was sputtered and deposited onto aluminum electrodes and counter-electroded to complete the metal-oxide-metal structures. This configuration was utilized to evaluate the dielectric, the device characteristics, and related process parameters. The effect of gas sputtering pressure, magnetic field strength, source-to-substrate distance, and power density on the rate of deposition is shown. Increased film thickness uniformity over a 3 by 3 in. area by optimum substrate positioning is indicated. Dielectric constant, dissipation factor, dielectric breakdown strength, insulation resistance, heat treatment, capacitance, and dissipation over the range 400 Hz to 5 MHz are reported. In the fabrication of silicon-integrated circuits, silicon dioxide has found use as a material suitable as a diffusion mask, for surface passivation of the silicon, and for protection of conductive films used for interconnections. Its use as a dielectric for thin-film capacitors in film hybrid circuits has been limited, to a degree, for lack of a compatible processing technique and because of its relatively low dielectric constant. With the recent advent of practical metal-oxide-semiconductor (MOS) field effect devices, the material is now being used to insulate the gate electrode from the conducting channel in the silicon. In this latter application, more stringent requirements have been imposed on .the oxide. A comprehensive resume of the use of silicon dioxide in integrated silicon device technology has been compiled including oxide film and bulk properties, method of oxide formations, and their applications.' A relatively new process to deposit SiO, and other dieIectrics is by rf sputtering, and the purpose of this paper is to describe the behavior of capacitors fabricated with a dielectric which has been sputtered from a quartz target and to indicate the relative effect of several of the process parameters on the film deposition. Work on rf sputtering of SiO2 and other dielectrics has been reported utilizing a triode type of sputtering system as described herein or a diode self-sustained glow discharge system. 2-8 SPUTTERING The process occurs during an electrical discharge in a gas plasma which provides the ions for acceleration to the target to produce the desired sputtering. The necessary plasma can be generated by a dc glow discharge through application of a high potential between two electrodes at approximately 2 to 10 x 10-2

Jan 1, 1969

By AIME

WE got our chance to talk with Arthur J. Blair at the Annual Meeting at the Pennsylvania Hotel. By two o'clock Wednesday afternoon things had quieted down enough so we had our interview in the foyer to the Ball Room. There were the usual questions. Where were you born? In La Salle County, Ill., on March 26, 1885. Where did you go to school? Northwestern University, B.S. degree in 1906. Where did you start work? For E. J. Longyear right after leaving school. One's ability as a geologist was measured by one's ability to wield a brush hook and ax. He stayed on the job as geologist for three years and then got to thinking about the advantages of a warmer climate. The advantages stacked up favorably, so off he went to Birmingham, Ala., just about the time U.S. Steel took over the Tennessee Coal, Iron and Railroad Co.

Jan 1, 1948

By W. G. Mine

In September, 1953, seismographs were installed in the Crowsnest Pass area of Alberta and British Columbia to study the 'bumps' which were occurring in the coal mines at Fernie and Coleman, and to investigate the possibility that they might be related to minor earthquakes in the area. During the initial phase of the work, three seismographs were operated at widely separated stations, two in the region of coal mines at Coal Creek and Coleman and one at Turner Valley, distant from any mining operations. Some earthquakes were recorded at all three stations and, in addition, many small disturbances were recorded by the seismographs located near the mines, especially -by the instrument at Goal Greek. A closer network of radio-linked seismographs was then in-stalled near Fernie, the records of which definitely established that the small disturbances were occurring in the mine workings, both active and inactive. No relationship was established between bumps and local earth-quakes in the area. This work was initiated as a -co-operative effort with the Fuels Di-vision of the Mines Branch, Department of Mines and Technical Surveys, which has undertaken a study into the phenomena of ground stress relief in underground mine workings.

Jan 1, 1958

By Jr. Koch

Statistical methods applied at the Bureau of Mines Denver Mining Research Center to data from metallic ore bodies were used to evaluate lignite reserves from core data and to predict the extent of lignite horizons in some Texas lignite beds. Six lignite seam units were studied using data from 361 drill holes. The data indicate a total of 214.2 million tons of lignite in the area examined, and probable reserves of 113 million tons in an area 2,000 feet beyond the limits established by the drill holes. It was demonstrated that lignite reserves present in lenticular beds could be reliably determined by statistical techniques, and that core drilling could be optimized to maximum information with minimum drill holes. The technique described is applicable to other coal beds.

Jan 1, 1966

By Jianbo Hu, Tao Zheng, Zhao Qihua, Rui Su

Rock mass discontinuities play a significant role in evaluating the stability of rock slopes. It is necessary to collect and analyze these discontinuities to fully understand the mechanical and deformational behaviors of rock masses. Based on the digital images of some slope faces, this paper proposes a framework based on machine learning for detecting and extracting discontinuities. First, digital images and photo poses are combined, the original scene is reconstructed, and 3D point cloud data are obtained. All captured point clouds can be mapped with each image by the direct linear transformation algorithm. Next, the detection machine learning algorithm is used to segment rock mass discontinuities on 2D digital images. Finally, based on the mapping relationship, the 2D digital images that were segmented are transformed into 3D point cloud data. The geometric parameters of the corresponding discontinuities can be extracted by the DBSCAN and the Skmeans algorithm and the characterization of specific rules. The proposed framework was evaluated utilizing a quantity of slope digital images in the Yebatan hydropower under construction, located in Sichuan Province, China, as a case study. The results illustrate that most deviations are less than 10° for the dip direction and dip angle, which verifies the reliability of the proposed framework and maintains acceptable measurement accuracy.

Nov 6, 2022

By S. Shimaya, T. Maejima, M. Shimo

"The authors conducted the in-situ gas-tightness tests in a fractured rock at the Namikata underground LPG storage site in Ehime prefecture, Japan. The test consisted of two independent setups, a gas-tightness test that used boreholes, and a chamber-scale test that used a horizontal drift sealed with a concrete plug. In each test, the gas pressure was increased up to the onset of the measurable gas flow to obtain the maximum containment pressure. This paper discusses the hydraulic conditions for gas leakage initiation and the importance of the pore pressure measurement for monitoring the gas-tightness of the LPG storage cavern based on the test results.INTRODUCTIONJapanese first underground LPG storage plant was constructed by JOGMEC, the Japan Oil, Gas and Metals National Corporation, at Namikata in Ehime prefecture in granitic rocks (Kato et al., 2007). The “hydraulic sealing principle” (Åberg, 1977) that utilizes groundwater flow into an unlined cavern to prevent the leakage of gas through fractures in the surrounding rock mass was employed for storage of LPG. This paper describes the results of the in-situ tests performed at the Namikata Site to obtain information on fundamental gas-tightness characteristics of fractured rock. Two types of in-situ tests, a borehole gas-tightness test and a chamber gas-tightness test, were carried out near the storage caverns. Figure 1 shows the cavern layout of the Namikata underground storage plant and the test locations. The storage facilities consist of three caverns (W26m×H30m×L485m). The cavern crown lies at a depth of 150m below the sea level in Cretaceous granitic rock (Figure 1). Water curtain boreholes excavated from the water gallery tunnel at EL-125m level are located above and side of the caverns to prevent water drainage from fractures during the construction stage as well as during operation. The borehole tests were performed from a drilling adit excavated from the eastern end water gallery tunnel, while the chamber test was conducted at the southern edge of an exploratory drift extending from the central water gallery tunnel."

Jan 1, 2015

By M. Zaki El-Sabban

Tables of chemical thermodynamic properties for the ideal gas state from 0° to 1,000° K are reported for eight alkanethiols, three cycloalkanethiols and arylthiols, six thiaalkanes, two dithiaalkanes, three thiacycloalkanes, and three thiophenes. They are based on current physical and thermochemical constants and definitions, reliable vibrational assignments, and the latest insights into molecular structure and energetics.

Jan 1, 1970