Search Documents

By C. C. Merrill

Studies were made to determine the amenability of yttrium to fused-salt electrorefining in a controlled atmosphere. Tests were conducted in a LiCl- YCl3 electrolyte system at 710° C. The major variables studied were the YCl3 content of the electrolyte, from l.7 to 13.4 mol percent, and the initial cathode current density, from 410 to 1,630 amperes per square foot. Vacuum distillation was employed to remove salt from the deposited metal. Metallic impurities, except for lithium, could be reduced to near or below their lower analytical limits, ranging from 10 ppm for Cu to 300 ppm for Ta; reduction of oxygen content, however, was accomplished only in metal produced from electrolytes with 5.4 mol percent YCl3 or less. Initial cathode current density had little effect on the purity of the product.

Jan 1, 1967

By AIME AIME

THE Federated American Engineering Societies through its Executive Board has endorsed House Bill 5230, introduced April 26, 1921, which provides for- the completion of the topographical survey of the United States. Before this bill can be reported out it will be necessary for the House Committee on -interstate and foreign commerce to hold hearings. This will not be done unless the engineers of the country show interest -and demand action which should be taken immediately after the recess ends and Congress reconvenes this fall. Surveys and maps have been made in this country ever since Captain John Smith mapped Chesapeake Bay about. 300 years ago, but it is only in comparatively recent years that the need for accurate maps has been keenly felt by those engaged in the industrial' and commercial development of the country.

Jan 1, 1921

By Walter Fuchs

IT is now generally conceded that coal is the product of deposition and transformation of debris of forests and swamps.29 Ample data are available to illustrate the metamorphosis of biochemical substances through biological action; other data show the progressive regional metamorphism existing in coal beds;25 and numerous examples of change effected by intrusion of igneous dikes into coal deposits have been established.23 However, often the relative importance of the biological and the geological factor in determining the character of the various natural coals is a debatable question. Since both biological and geological factors are ever present in nature, the problem, at first glance, would appear to resemble certain probability problems: specifically the simultaneous toss of two coins, with the biological factor as heads and the geological as tails. The probability is 2:I for the combined effect of both factors, as compared to the exclusive effect of either one. if the a priori probability is the same for each factor. This condition can be analyzed by a thermodynamic treatment of data, which may be obtained from a consideration of pertinent biological, chemical, geophysical and geological facts. SYNOPSIS OF BIOLOGICAL AND CHEMICAL FACTS The biosphere is not sterile; i.e., microorganisms are always present. Microorganisms have been established in the ocean deep, under the ice of the polar regions, in the sand of the deserts, and in swamps far below the surface. The various biological media may be acid, neutral, or alkaline, and they may or may not be readily accessible to air. Microorganisms are encountered almost everywhere, except where the temperature is not within the range tolerable by microbial life. Of course, with changing conditions, the type of microorganisms will change. All chemical products of life-proteins, fats, carbohydrates, lignins, waxes, resins may serve as a habitat of microorganisms. In the decomposition of a medium, some microorganisms macerate organic matter mechanically and remove certain constituents for their own nutrition; others decompose a large part of the organic matter but may leave certain constituents undecomposed. Some attack only certain specific ingredients of the organic matter. All of them build up cell substance. The nitrogen content of the medium largely determines the degree of decomposition. Below 1.7 per cent nitrogen, growth of microorganisms and hence decomposition of organic material is retarded; consequently organic material will accumulate. l7,32 Such accumulations of organic material may give coal eventually. Coals differ in type and rank. The nature of the original vegetation and the conditions attending the transformation of the accumulated debris determine the type of coal such as bright, splint, cannel, and algal or boghead coals. Chemical analysis of representative samples of a given type of

Jan 1, 1941

By Liu Fan, Shang Yanbo, Wang Zhongming

"Besides valuable metals of Cu, Sn, WO3, Zn, there are S, Ag, CaF2, In and so on in a complex ore deposit in south China (which belongs to Hu Nan Shizhuyuan Non-ferrous Metal Limited Liability). Although it proved reserve amounts to 3.5×107 ton, its crystal character limits its utilization in large-scale. It features complex relationships between valuable minerals, finest crystallized particle size, low-graded valuable metals (Cu 0.30%, Zn 0.5-0.7%, Sn 0.2%, W<0.1%). If only tungsten minerals are considered, it means WO3 grade is too low (the cut-off grade of WO3 is 0.1% in China). Only Cu and Sn minerals are recovered from 2006 and Cu recovery is less than 70%, Sn 15-20%. Other valuable metals of W, Zn, S and CaF2 were lost in the tailings. To make good use of the ore, the technology of fully recovering Cu, Sn, W, Zn, CaF2 and rare metals are in urgent need. After systematic researches, the flow sheet of "bulk flotation of Cu-Zn minerals at first, then Cu-Zn separation, then recovering sulphide by flotation, then recovering iron minerals by magnetic separation, then bulk flotation of Sn-W minerals after desliming" is developed. Furthermore, specific Sn-W collectors of BK411 and BK412 are applied into the processes and better indexes are obtained. The industrial indexes are listed as followings: the content of Cu, Zn, Sn, WO3 of ROM ore is 0.31%, 0.65%, 0.13%, 0.03%; Cu and Zn recovery are 82.23% and 37.79% respectively; 63.76% of Sn and 34.34% of WO3 go into the Sn-W bulk concentrates. Economic benefits are remarkable."

Jan 1, 2014

By R. R. Sayers

A series of coal- mine catastrophes in the latter part of the first decade of this century focused public attention on the need for safety in mines and resulted in the establishment of the Federal Bureau of Mines , whose primary function was to promote safety and improve hygienic conditions of workers in the mineral and related industries . These activities are carried out by the Safety Division of the Bureau's Health and Safety Service . In general , the work performed by the Safety Division personnel may be classified as educational and investigative . Instruction is given in accident prevention for mine officials and miners ; first aid to the injured ; the use and care of oxygen breathing apparatus ; and advanced mine rescue and recovery operations . A specialized safety course is offered to the petroleum and gas industries . Division personnel also aids in or directs rescue and recovery work after mine fires and explosions ; assists at first - aid and mine rescue contests ; conducts safety exhibits and demonstrations ; and presents safety talks , often accompanied by sound safety motion pictures or latern slides , before employee and official groups , at meetings of Holmes safety chapters , at mining institutes , and at other safety or technical gatherings . Coal - mine fires and explosions are investigated , as well as quarry or metalmine explosions and fires , miscellaneous accidents , health and safety hazards , and safety conditions at mines and plants ; safety devices are investigated and developed . Field studies cover ventilation , methods of allaying suspended coal - dust particles , prevention of dust accumulations , the proper use of rock dust to prevent or limit explosions , explosives practices , and the care and use of underground equipment . The results of these studies and investigations are widely applied in the various training courses and are prepared as reports and recommendations , which are submitted to interested persons or are combined and distributed to the public as bulletins , technical papers , miners ' circulars , information circulars , and reports of investigations . These studies also afford a basis for the development of new or modification of old Safety Decisions of the Mine Safety Board of the Bureau of Mines . The following pages review the accomplishments of the division as regards safety during 1942,2/ with like information for a series of recent years and summaries to date . A striking feature of the division's work has been the safety education of more than 1-1/2 million persons who have taken first -aid and mine rescue training courses . That these efforts over a period of 3 decades have been successful is revealed by the decline in coal - mine fatality rates and a somewhat smaller decrease in metal - mining and quarrying fatality rates .

Apr 1, 1943

Alluvial mining even of shallow deposits is often economically a marginal proposition and causes significant disruption of the land surface through the need for large scale excavation. In-situ leaching using chlorine-based solutions eliminates the need for excavation, the disruption of surface activities, and may greatly reduce processing costs and improve recovery especially of fine gold. A spreadsheet model has been developed to design and analyse the economics of in-situ leaching of alluvial deposits. In-situ leaching of shallow deposits may be achieved in a number of ways including solution infiltration via perimeter ditches or the use of injection and production wells. In most instances deeper alluvials may only be processed using well systems. Two deposits are analysed in this paper. The first consists of one metre of payable wash beneath one metre of overburden. Some thirty fields per year are treated processing 450 000 BCM per year at a cut-off grade of around $4/tonne ($8/rn3 or the gold value equivalent of 0.26 gh or 0.52 g/m3). The principal costs are well drilling and labour. Sensitivity analysis indicates that doubling the throughput halves the cost. The economics of the project are relatively insensitive to reagent costs and consumptions, and halving the recovery doubles the cut-off grade. Shallow deposits treated using the infiltration ditch system may be marginally cheaper and more conveniently managed although this depends on the relative cost of digging the perimeter ditches. In a second example, deep leads with one metre of wash beneath 30 metres of overburden necessitate significant drilling and feature reduced throughputs as a consequence. In the example chosen 30 fields a year are processed for an annual throughput of 65 000 tonnes costed at around $20/tonne (1.4 g/t Au equivalent, $40 /m3). Sensitivity analysis indicates that throughput, and drilling cost per metre are not important but there is a high sensitivity to recovery and to the depth to payable wash.

Jan 1, 1992

By HOWARD I. YOUNG

F. W. SPERR, Houghton, Mich.-Why does 10 to 20 per cent. of the ore formation have to he lost? It is not clear to me why it should not all be taken out, from the conditions as I saw them underground this afternoon. H. I. YOUNG.-The grade of our ore is so low that we cannot stand the expense of timbering to support the roof, which, in a sheet-ground mine, would be from 25 to 50 per cent. of our total mining cost at present. After the orebody is mined out, we can often recover 10 to 20 per cent. of the material that is left. F. W. SPERR.-I think it should be a very simple mining engineering problem to mine all of that mineral without the use of a stick of timber. Similar work has been done in the mines of Grand Rapids Plaster Co. The usual operation in deposits of this kind is to open up and excavate as far as the roof will stand; when it caves, start in and dig somewhere else. But in the case I referred to they learned that by working the ground more systematically and leaving in a sufficient amount of pillar, they could later draw those pillars and get them all, and avoid uncon¬trolled breakages which would be likely to occur if they tried to hold up the overburden permanently. From the point of view of safety and also from the financial point of view, I contend that it is better to keep the caving under control and make it do what you want it to do, rather than to take out what you can conveniently for the time being and after a while be compelled to let the overburden do what it pleases.

Jan 1, 1918

By Joseph E. Matta

The Bureau of Mines conducted a field study to investigate thin suppression of respirable dust by water sprays on a continuous-mining machine. Determining the importance of the top and bottom sprays for two types of spray nozzles was emphasized. Results showed, at a 90-pct confidence level, that (1) at least 70 pct of the dust was generated during the sump cut, even though nearly half of the coal was mined during the downshear operation, (2) the water sprays on the top of the boom had little effect in suppressing respirable dust, and (3) B.D. 5 spray nozzles mounted beneath the boom reduced dust at least 33 pet more than B.D. 5 sprays mounted on top of the boom. A single-cut technique was developed that gave good reproducibility for replicate cuts (coefficient of variation of 20 pct).

Jan 1, 1976

By Getúlio da Silva Abreu

O objetivo geral deste trabalho foi produzir e caracterizar as propriedades mecânicas de um compósito abrasivo nanoestruturado no sistema D-Si, via sinterização cíclica de alta pressão e alta temperatura (APAT). A sinterização cíclica em alta pressão e alta temperatura de compósitos foi feita a partir de uma mistura de 70% diamante e 30% de Si como ligante, e com 1 a 4 ciclos de pressão (P) de 7GPa-4GPa e temperatura (T) 1600°C-300°C, para um tempo (t) de 1min. O aumento do número de ciclos gerou razoável elevação na microdureza e densidade das amostras. Os valores médios de tenacidade à fratura ficaram entre 8,86 e 9,43 MPa.m1/2. No ensaio de desgaste o aumento do número de ciclos diminuiu a perda de massa das amostras no disco de granito. As curvas termogravimétricas apresentaram uma boa estabilidade térmica dos compósitos até a temperatura de 660ºC. Finalmente, por meio deste trabalho será possível melhorar a produção de futuros compósitos abrasivos no sistema D-Si.

Aug 16, 2017

By William S. Hallager

Banded ironstone and associated fine-grained carbonaceous sediments near Jardine, Montana, are enriched in gold, arsenic, and tungsten. The mineralized sediments lie within a thick sequence of quartz-mica schists cut by a 2.6 b.y, granite. Surface, underground, and drill hole mapping are used to construct structure contour maps of individual ironstone lenses. Each lens is then unfolded by triangulation of minimum surface path distances between drill hole penetration points. Major and minor element abundances in composite ironstone samples are interrelated through R-mode factor analysis. Results indicate five significant element groupings thought to reflect coarse detrital, fine detrital, sulfide-rich chemical, iron-rich chemical, and epiclastic ultramafic sediment. Ultramafic factor scores are highest in a previously undefined rock type rich in cummingtonite, biotite, and chlorite; lacking in quartz; and closely associated with at least one ore horizon. Detrital dilution of ironstone, calculated from chromium and nickel content, drops off significantly as ore-bearing ironstone is approached. This observation may indicate that centers of gold precipitation have protected themselves, either topographically or by rapid deposition, from detrital contamination. Gold mineralization correlates most strongly with the sulfide- rich factor. Gold may have been introduced through hotspring activity as a bisulfide complex.

Jan 1, 2013

By Carlos Vinícius Domingos de Carvalho

As perdas geradas nos processos de uma Aciaria contribuem de forma significativa para a perda metálica do processo. Eventualmente, mesmo com uma operação correta, do ponto de vista de características do produto, pode ocorrer comprometimento do ponto de vista econômico, e uma forma de redução direta dos custos e aumento de performance é a redução das perdas geradas no processo. Desta forma, tornou-se importante realizar um estudo para reduzir as perdas metálicas na Aciaria. Foi utilizado a metodologia Seis Sigma, sendo estratificadas as perdas por processo na Aciaria, onde as maiores perdas na rota dos processos de Lingotamentos Contínuos foram: perda no Distribuidor (24,7%), corte de sequência (17,5 %), retorno de corrida por baixa temperatura do aço na panela (16,3 %); perda por obstrução da válvula da panela (8,8 %). A perda metálica foi reduzida em 50,8%. Além da redução expressiva das perdas, houve uma grande contribuição em relação à compreensão dos modos de falhas para apropriação correta das perdas, tornando as informações mais seguras e facilitando o tratamento de possíveis falhas no processo.

Oct 30, 2017

By Gustavo Coqui Barbosa

Neste trabalho, foi desenvolvido um modelo de elementos finitos para simular o primeiro passe da laminação a quente do trem acabador de tiras de aço C-Mn. O comportamento desse aço é definido por equações constitutivas que descrevem os mecanismos de encruamento e recristalização acoplados aos campos de tensões, deformações e temperatura. Foi implementada uma sub-rotina em linguagem FORTRAN disponível no programa de elementos finitos ABAQUS/Standard. O modelo foi estabelecido no estado plano de deformação por meio de elementos finitos com acoplamento dos campos de temperatura e deformação para o cilindro de trabalho e tira. As dimensões e condições de processo foram obtidas a partir de dados industriais do laminador de tiras a quente da CSN. O modelo prevê as distribuições de temperaturas e valor de carga de laminação em boa concordância com as medidas industriais. Os resultados do modelo evidenciam que há ocorrência de recristalização dinâmica durante o primeiro passe e, apontam que em determinadas regiões da tira a fração recristalizada dinamicamente chega a 100%. A análise de sensibilidade dos parâmetros do modelo foi feita para determinar o seu impacto nos resultados das simulações, notadamente na força de laminação e no tamanho de grão austenítico final.

Jul 30, 2018

By L. H. Adami

Heats of formation were obtained for four anhydrous crystalline sodium borates by hydrochloric acid solution calorimetry. The heats of formation at 298.15° K from the elements are NAB02, -233.2 ±0.6 kcal/mole; Na2B07, -786.4 ±1.0 kcal/mole; NaB305, -549.9 ±0.8 kcal/mole; and Na2B6013, -1,412.5 ±2.0 kcal/mole, The heats of formation from the constituent oxides are NaB02, -31.5 ±0.8 kcal/mole; Na2B407, -78.8 ±1.3 kcal/mole; NaB305, -44.1 ±0.8 kcal/mole; and Na2B8013, -96.7 ±1.5 kcal/mole.

Jan 1, 1968

By H. Kenworthy

Laboratory experiments were conducted on several materials to determine their suitability for the production of mineral wool. By blending raw charges in the proper proportions and in some instances by adding lime, acceptable wools were made from samples originating in Alaska, Florida, Texas, and Virginia. It was shown that satisfactory wools can be produced from many kinds of raw materials if the ratios of acidic and basic constituents are properly maintained. INTRODUCTION The Federal Bureau of Mines has facilities at the Mississippi Valley Experiment Station, Rolla, Mo., for examining and testing mineral-wool raw materials. Samples are evaluated through small-scale wool-blowing experiments, aided by petrographic, chemical, and physical analyses of the raw materials and finished wools. When enough experimental data have been accumulated they are made public through Government reports and periodicals. This report of investigations follows that published in 19513/ and presents test data on samples received and examined since 1951.

Jan 1, 1956

By C. A. Garzonio, A. M. G. Affuso

The paper describes the analyses and the tests carried out on representative slabs of white Carrara marble which have highlighted the correlation between the micro fabrics and physical and mechanical parameters. The aim is to determine the conditions which indicate the triggering and evolution of the deformation phenomena. La note écrit l’analyse et les epreuves effectuée sur un echantillon représentatif de nombreuses dalles en marbrede Carrara. Les études montrent la correlation entre la minéralogie et les paramètres physiques et mecaniques. Le but est déterminer les conditions qui indiquent l’amorçage et l’evolutions des phénomènes de déformation. Diese Arbeit gibt eine Beschreibung der experimentalen Untersuchungen und der Analysen über die Marmorplatten von Carrara. Daraus resultiert, dass die Charakterisierung der Mineralogie und die Porosität der Gesteinsmaterialien die physikalische mechanische Degradation beurteilen und die Krümmungen bestimmen.

Jan 1, 2003

By W. W. Mason

The United States began exporting coal in the late 1800&apos;5, at first in very small quantities to Canada and beginning in 1897 and 1896, to the east coast of South America. Shipments to European countries began on a very limited basis in 1902 and these shipments increased gradually until World War One when shipments overseas increased from the 8 million tons per year level to 22 million tons. After the war exports dropped as fast as they had increased and, with the exception of exports to Canada, remained at very low levels until just after World War 11 when the United States again emerged as a major coal exporter. World War II left the coal industries of Europe in ruin. As the United States was the only country able to supply the large quantities of coal at reasonable prices needed for reconstruction of the European economy, the U. S. coal exports overseas expanded rapidly to 42.5 million tons in 1947. Additionally, we shipped 25 -2 million tons of coal to Canada In that year for a total export of 68.7 million tons. Unfortunately, that level was not reached again until 1957 when exports reached an all-time high of 76 .4 million tons- -a high I might add that has not been reached since.

Jan 1, 1980

Develop hydrometallurgical or pyrometallurgical recycling methods to recover valuable rare-earth compounds from various forms of NdFeB magnet scrap. Background The U.S. Bureau of Mines (USBM) has developed technology to treat and recycle a variety of wastes containing valuable and strategic metals. As part of this effort, the USBM developed a process to separate neodymium and other valuable rare earths from iron in NdFeB magnet scrap (fig. 1). Since this scrap typically contains nearly 30 weight percent neodymium and since the demand for neodymium is constantly increasing, cost-effective methods for scrap treatment could have a significant impact on industrial expenditure and materials supply in the expanding area of magnet manufacture. Approach A hydromctallurgical, H2SO4 dissolution-precipitation process provided the most effective treatment for separating rare earths from bulk NdFcB magnet scrap (fig. 2). Precipitation of neodymium-alkali sulfate double salt proved advantageous over direct precipitation of fluoride or oxalate products. This double salt is easily converted to a variety of useful rare-earth compounds, which eliminates many of the materials-handling and economic problems inherent with direct precipitation. Following rare-earth precipitation, dissolved iron was removed from the acid leach solution by precipitation as a jarosite.

Jan 1, 1993

By Naiyi Li, Henry Hu, Alfred Yu

"In the past few years, various squeeze cast aluminum components have been developed and successfully implemented in various vehicles by the automotive industry because of their superior engineering performance. However, fundamental understanding of the formation of air gap during squeeze casting processes is still very limited despite of its significant influence on the extent of heat transfer between the casting and mould. In this paper, a mathematical model has been developed to simulate phenomena of air gap between the casting and mold' during squeeze casting of aluminum alloys. The model considers the effect of process parameters such as applied pressures and mold temperatures on the events of air gap formation. The predication indicates that the occurrence of highly enhanced heat transfer in squeeze casting of aluminum alloys primarily results from the presence of excess applied pressures.IntroductionA number of squeeze cast Al components has been developed and used in mass-produced vehicles in the past few years, such as steering knuckles, Road wheel, Engine Block etc. This is attributed to their superior engineering performance. In squeeze casting, the cooling rate can be increased by applying high pressure during solidification which results in the noted refinement in the micro structure scale leading to better casting properties. However, the excessive pressure increased interfacial heat transfer coefficient is affected during the solidification by air gap formation and die surface condition etc., which is believed to increase thermal resistance at the casting/die interface [l - 4]."

Jan 1, 2004

By Amauri Garcia, Noé Cheung, André dos Santos Barros, Clarissa Barros da Cruz

Embora a resistência ao desgaste seja geralmente a principal propriedade avaliada decorrente da adição de terceiros elementos em ligas Al-Sn, não somente os fenômenos tribológicos são responsáveis pela deterioração gradual das peças, mas também os fenômenos relacionados à corrosão. Dessa forma, o presente estudo objetiva analisar o efeito de características microestruturais formadas durante a solidificação transiente da liga Al-9%Sn-5%Zn na resistência à corrosão em solução 0,06M NaCl investigada por polarização potenciodinâmica e espectroscopia de impedância eletroquímica. Foi observada uma morfologia microestrutural caracterizada por dendritas da fase α-Al com concentrações de Zn tanto na matriz dendrítica quanto em regiões ricas em Sn localizadas nos contornos interdendríticos. A evolução dos espaçamentos dendríticos primários (λ1) também foi correlacionada com parâmetros térmicos de solidificação. Finalmente, constatou-se que a amostra com microestrutura mais grosseira, ou seja, λ1 = 89,6 μm, apresentou comparativamente menor densidade de corrente de corrosão e maior resistência à polarização.

Oct 1, 2019

By Signe Kjelstrup, Leiv Kolbeinsen, Marit Takla, Odne Burheim

"This paper presents a Seebeck-type solid state thermoelectric power generator unit, designed to investigate the possible recovery of radiant waste heat at a silicon plant in Norway where roughly 703 of the total input energy leaves the process as waste heat. The unit is 0.5 m x 0.5 m and is built of 36 commercially available thermoelectric devices based on bismuth telluride p - and n - type semiconductors. Thermoelectric devices directly convert fractions of a heat flux into an electric current (and vice versa) and may therefore be convenient for recovery of waste heat when the heat source is discontinuously available. The purpose of the thermoelectric unit is to give a proof of principle of direct thermoelectric energy conversion on a large scale. We present the initial test results for the generator. At an average temperature difference between the heat reservoir and the heat sink of 98°C, we measured an open ciruit potential of 23.44 ± 0.06 V and the matched load power output was 39.4 W. At a temperature difference of 220°C, we predict the generator open circuit potential to be 40.8 V, which corresponds to an efficient Seebeck coefficient of 242 µV /K, and matched load power output to be 120 W.IntroductionThe world's power demand increases, driven by population growth and increase in living standards and simultaneously global warming is recognized as one of our most serious environmental problems. According to the International Energy Agency[l], the industrial sector accounted for approximately one third of the total global power consumption in 2005. Increasing the energy efficiency of industrial processes thus represents a benign and substantial route for addressing environmental concerns and energy security.In accordance with the second law of thermodynamics, all real processes are associated with lost work which is energy being dissipated as heat to the surroundings[2]. Improving the energy efficiency of industrial processes is about finding the process path associated with a minimum of lost work. The more evenly the losses are distributed, the smaller are the losses [3, 4]. In addition, exploiting the unavoidable waste heat will contribute to improve the energy efficiency. The waste heat may be utilized for heating purposes and/or it can be upgraded to work for instance via some sort of heat engine."

Jan 1, 2012