Search Documents

By Silvano Morelli, Giovanna Cassani, Renzo Bindi, Antonio Nicola

More than 70 km of main line and service tunnels have been excavated to date for crossing the Apennines between Bologna and Florence. A new design and construction approach, known as Analysis of the Controlled Deformation in Rock and Soils, (ADECO-RS), was adopted to tackle the extreme heterogeneity of the ground and the particular stress-strain conditions. The goal of this system is to obtain constant and predictable full section advance rates, even in very poor geology, with the highest possible level of safety and reliability. The execution of this gigantic project required the mobilization of 21 job-sites, with the concurrent operation of 30 excavation headings. The global production rates confirm the high quality of the design and the high level of industrialization reached during the construction stage, levels not previously obtained in similar conditions, using other approaches such as NATM.

Jan 1, 2003

By H. J. de Haan, J. van Lookeren

In view of their size and favorable characteristics, Shell's heavy-oil fields on the eastern coast of Lake Maracaibo, Venezuela — known as the "Bolivar Coast" — are obvious candidates for the application of thermal recovery methods. During the last decade various methods have been tested, such as steam drive,', steam soak and in-situ combustion.3 Steam soak was discovered as a promising production method rather accidentally in 1969, during early steam drive testing in the Mene Grande Tar Sands1 When steam erupted at the surface due to breakdown of the overburden, the injection wells were back-flowed to relieve the reservoir pressure. This resulted in high oil production rates, all the more impressive because the reservoir is unproducible by primary means. It was concluded that injection of limited amounts of steam might be a very effective method for stimulation of heavy-oil wells. To obtain information that would be more widely applicable, testing of the process was continued in the eastern part of the Tia Juana field (Fig. 1). Here even more favorable results were obtained than in Mene Grande. This created sufficient confidence to prompt a large-scale project, which was considered essential for an adequate evaluation of ultimate recovery, steam requirements, mechanical problems and economic prospects. To obtain an early answer on the ultimate recovery a fairly depleted area was selected in the western part of the same field ("A" in Fig. 1). The first steam was injected in March, 1964. This paper describes the performance until the end of 1966. The production mechanism and well inflow performance are discussed in some detail. In view of the favorable results obtained so far, steam soak operations have expanded considerably since the start of this project. Presently, five other projects are under way, of which two are about the same size as the one under discussion, with further extensions being programmed. Description of the Project Reservoir Data Shell's part of the Main Tia Juana reservoir has a proven area of 8,800 acres and an average net oil sand thickness of 130 ft. It contained an initial quantity of 2,750 million bbl of stock tank oil (STOIIP), with an API gravity ranging from 10 to 15 API and a viscosity of 100 to 10,000 cp (at 122F). As a geological unit it is known locally as the Lower Lagun-illas member of the Lagunillas formation, which is early Miocene in age. The sand bodies are believed to be distributary channel sands deposited in a lower coastal plain. Most of the channel sands have lateral and some vertical communication. The field was developed mainly in the period from 1936 to 1950. The ultimate primary recovery is estimated at 18.1 percent of STOIIP, of which 12.5 percent STOIIP had been produced by the end of 1963 from some 540 wells. By then the average pressure had decreased from an initial value of 960 to 550

Jan 1, 1970

By R. J. Anderson, A. V. Castelli

In 1986, United States' barite production fell 48.9%, consumption - sold or used by grinding plants - was off 47.3%, and imports were down 63.8%. Meanwhile, world mine production decreased 29.6%, according to the US Bureau of Mines. However, value of US-produced barite FOB mine increased 46.51%, according to USBM figures. The declared value CIF US port of all imported unground barite decreased from $41.94/t ($46.23 per st) to $39.02/t ($43.01 per st). Nevada continued to be the leading US producer of barite with 69% of the total. It is followed by Georgia, Missouri, Tennessee, and California. The USBM estimates that 65% of the barite mined was used as a weighting agent in drilling fluids. The remaining 35% was used in the production of barium chemicals and as a filler. Most of the production from Missouri, Georgia, and Tennessee was used in the non-oilfield sector. This sector made up a larger percentage of the US produced barite in 1987 than it did in 1986, increasing the overall value per ton of barite. Barite consumption was at its lowest since 1963. It is estimated that 80% of the barite was consumed in the drilling fluid market. The remaining 20% was used in barium chemicals, glass, and as filler in plastics and paper. The decline of barite used in drilling fluid followed the decline in the average number rotary rigs operating - 964 versus 1968 in 1985. This was the lowest average number of rotary rigs operating since 1971. The non-oilfield market was up 5.3% in 1986. This increase can be attributed to the increased use as a filler in plastics. Imports of crude barite, though down nearly two-thirds, still made up 65% of the barite consumed in the US. China was the leading exporter to the US with 58%, followed by India, 15.4%; Morocco, 11%; Thailand, 5.4%; Mexico, 4.6%; Chile, 3.9%; and Ireland, 1.7%. Less than 1% of the imported ore was used in the nonoilfield sector. Imports of ground barite dropped from 64.4 kt (71,000 st) to 19.8 kt (21,800 st) in 1986. Of this amount, 14.1 kt (15,500 st) were used in drilling fluids in 1986 and the remainder for non-oilfield use. During 1986, more of the grinding plants supplying the drilling fluid market were closed. Dresser Magcobar and IMCO Services, a Halliburton company, formed M-I Drilling Fluids Co. Mine production in the US will probably decrease in 1987 due to the lower cost of imported ore. No significant change is expected in the drilling fluid market. The average number of operating rotary rigs is estimated at 950 in 1987 versus 965 in 1986. The nondrilling fluid markets (chemicals, glass, and filler) will follow the overall US economy. Bauxite and alumina R. J. Anderson, Ohio State University US bauxite production in 1986 dropped to a pre-World War II level, continuing a decline that began a decade ago. 1986 production totaled 450 kt (496,000 st), compared to 674 kt (743,000 st) in 1985. World production of bauxite also decreased in 1986. This reflected the soft market in alumina, aluminum, and related products. Total mine production worldwide came to 79 Mt (87 million st), down from 85 Mt (94 million st) in 1985. For the sixteenth consecutive year, Australian production of bauxite led all other sources. No other country approached the 28 Mt (31 million st) mined in Australia in 1986, despite a 4.4-Mt (4.9-million st) drop in its output from 1985. Other major producers in 1986 were: Guinea 11 Mt (12 million st), Brazil, 6.5 Mt (7 million st), Jamaica, 6.5 Mt (7 million st), and Suriname 2.8 Mt (3 million st). Despite weakness in world demand for bauxite, Venezuela, heretofore an alumina producer, is now pushing development of a new mining venture near the western border of the state of Bolivar. Plans call for barging bauxite down the Orinoco River to the Ciudad Guyana alumina plant, a distance of 650 km (400 miles).

Jan 5, 1987

By Wesley, Worner H

During the meeting of the Institute last year at Port Pirie, the opportunity was taken to sample the lead bullion coming from the blast furnace and various stages during the refining process. Also, in the desilverising section, the upper zinc rich phase was sampled as the silver content built up and in the cupellation operation a series of samples was taken as the silver content of the bullion increased. In these two cases, the samples were taken under the supervision of a member of the staff of the Broken Hill AssociatedSmelters.In the following account of the microstructure of the samples taken, only the main phases present have received attention. In this connection deduction from phase diagrams of binary alloys has been used in conjunction with the assays carried out on duplicate samples taken at the same time as those for micro examination.

Jan 1, 1938

By H. H. Wade, N. F. Schulz

The large quantities of iron-bearing materials, including taconite, semi-taconite,* and other low-grade ferruginous materials occurring in Minnesota and elsewhere, constitute an important potential source of iron. Satisfactory grade and recovery of iron ore concentrate cannot ordinarily be obtained from these ferruginous materials by simple methods of beneficiation. Iron is distinctive in that the free metal and two of its oxides [magnetite (Fe2O3) and maghemite (gamma-Fe2O3) ] are strongly ferromagnetic. The successful magnetic separation of natural magnetite from taconite has already been established on a commercial scale. The iron in semi-taconite, however, occurs largely as goethite (Fe2O3-H4O) and hematite (Fe2O3) which do not respond to ordinary magnetic separation methods. Magnetic roasting converts these iron oxides to magnetite, which can, after liberation, be magnetically concentrated. MAGNETIC ROASTING Hematite undergoes a stepwise reduction when exposed at moderately elevated temperatures to a reducing atmosphere containing hydrogen or carbon monoxide: Fe2O3? Fe3O4 ? FeO ? Fe Since the desirable product in magnetic roasting is Fe3O4, the conversion is halted after the first stage by controlling the reduction potential of the gas mixture with water vapor or carbon dioxide. The reducing gas mixture must be such that the oxygen partial pressure at the solid-gas reaction interface will be maintained intermediately between the oxygen partial pressures in equilibrium with Fe2O3 and Fe3O4 at the prevailing temperature. Because of the rapid increase in decomposition pressure of Fe3O4 with increase in temperature, the practical upper limit of useful reaction temperature is about 1400°F, above which over-reduction usually occurs in atmospheres containing hydrogen or carbon monoxide. On the other hand, useful reaction rates usually occur only above 800°F. Goethite reacts similarly except that the combined water probably has to be driven off thermally before the reduction to magnetite occurs. Iron carbonate must also be decomposed thermally to an oxide before conversion to magnetite. Iron silicates are apparently not amenable to magnetic roasting. The rate of penetration of the reaction toward the interior of a given ore fragment is dependent on the chemical composition and physical structure of the solid. Most ore fragments tested here reduced satisfactorily to 1/4-in. depth in less than 14 min at 1200°F. Some very dense fragments, however, were reduced to less than 1/32-in. depth under the same conditions. Determination of the optimum temperature, gas composition, ore fragment size, or time of exposure

Jan 1, 1961

By Turnbull A. G

Thermodynamic calculations based on the ideal system NiO - Fe203 - H2(g) - CO(g) - H2O(g) - CO2(g) show that it is not possible to selectively reduce nickel oxide in the presence of hematite because ferronickel is the zero-valent nickel-containing product. The calculations show that temperature, reducing atmosphere composition and oxide to reductant ratio have a marked effect on the nickel content of the ferronickel alloy and the amount of nickel reporting jn the alloy. The general trends based on the calculations correlltte well with experimental observations.

Jan 1, 1980

By A J. Cornah

Critical decisions in iron ore project evaluation and production are based on global and local spatial estimates of primary mineral deposit properties (such as in situ geochemical grades) and geometallurgical responses (such as screened, washed or concentrated product yields and grades), which are derived from limited sample data. These spatial estimates are typically made using classical geostatistical techniques, which fundamentally assume that the attributes of interest behave additively. This assumption is generally appropriate for æprimaryÆ variables but æresponseÆ variables may behave non-additively and therefore their direct linear estimates may be biased.In this paper an existing additivity testing mechanism is used to quantify the bias resulting from direct linear estimation of a non-additive iron ore attribute. Data from a magnetite project are used to determine the circumstances under which such biases may be of material impact. The implications for iron ore resource estimation, geometallurgical modelling and grade control are outlined and discussed.CITATION:Cornah, A J, 2013. Assessment of the impact of non-additivity in the estimation of iron ore attributes, in Proceedings Iron Ore 2013 , pp 129-136 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 12, 2013

By Parker A. J, Giles D. E

Solutions of copper(II) sulphate in acidified aqueous acetonitrile leach copper from copper-lead matte derived from the drossing of lead with sulphur to produce solutions of copper(I) sulphate. The reactivity of the matte constituents towards copper(II) sulphate is Cu2S> PbS > CuS > > Pb. According to the leach conditions, part or ,all of the copper may be leached 'leaving a residue of CuS/PbS, or S/CuS/PbS04, or S/PbS04, to be recycled to the lead smelter. Complete extraction of the copper requires leaching with oxygen which occurs under mild conditions in the presence of acetonitrile and sulphuric acid in water. Copper is selectively recovered as a pure product by electrochemical or thermal disproportionation of copper(I) sulphate solutions. A notional process is proposed.

Jan 1, 1979

By Casey Erickson

Goldstrike Property ??Located in Elko, NV USA?Carlin Trend ??Mining Since 1985 ??27 Million Ounces of Gold Mined ??Production of 400,000 tons/day ??1,600 Employees

May 1, 2011

By Se-joon Kim, Jong-hwa Chun

"‘Gas hydrate’ is the common term for a solid material formed from the combination of various gases as ‘guest’ and water as ‘host’. A series of large-scale scientific drilling and coring programmes conducted since 2000 revealed that natural gas hydrate exists in a wide variety of accumulations in the sediments. The scaled-up onshore and offshore field production tests during the last decade show that gas production technology will be realized to make gas production from gas hydrates viable in the future, recognizing its potentials as one of the future sustainable energy resources.The total produced gas was approximately 470 m3 by the hot water circulation method over 6 days of operation in the permafrost-associated Mallik 2002 project in the Mackenzie Delta of Canada. In the Mallik 2007-2008 project, the gas was successfully produced stably by the depressurization method for 6 days, up to 13,000 m3 cumulatively. The depressurization method applied in the Mallik test was shown to be an effective way to produce gas from gas hydrates. The Alaska field trial to inject mixed gas of CO2 and N2 to exchange CH4 in 2012 was successfully done for the first time to produce maximum 1,270 m3 per day. A remarkable achievement was made by Japan when it completed its first offshore production test in the Eastern Nankai Trough, producing approximately 120,000 m3 of methane by the depressurization method over 6 days in March 2013. The technical challenges and scientific uncertainties obtained from Nankai Trough production test provide Korea with more considerations as to the aspects of well completion, reservoir formation and seafloor stability, sand control, flow assurance, environmental monitoring, and etc., due to the different geological setting and geomechanical properties of the Ulleung Basin in Korea."

Sep 1, 2014

A review is made of the limited published experience of the effects of cemented fill in flotation.A general approach is adopted in listing and discussing possible sources of, and reasons for, ore contamination by cemented fill, together with basic, fundamental approaches to minimizing this contamination. These approaches involve basic mining design, effect of fill placement density, optimization of curing time and of cement content, variation of fill particle grading, use of flocculants and of pozzolans, fill placement and dewatering, and or blasting and handling practice.

Jan 1, 1974

By Wm. Mark Hart

High horizontal stresses and shear failure have been considered the major reasons that cause entry roof failure and falls for underground mining. Therefore, reorientation of the current mining systems or layouts or using angular crosscuts in mains or gate entries becomes more popular if a greater than normal horizontal stress is measured. However, reorientation of the current mining systems or layouts is always expensive and use of the angular crosscuts may weaken the pillar structure at corners. Therefore, cautions must be taken before any decision related to reorientation of the current mining systems or layouts or use of angular crosscuts is going to be made. In order to prevent entry roof failure and falls, the following two issues must be carefully examined and fully understood: 1. Which one, shear stress or tensile stress, is going to be blamed for entry roof failure? 2. Which one, horizontal stress, vertical stress, or local geological weakness plays a major role in entry roof failure and falls? This paper analyzes the mechanisms of entry roof failure and falls for underground mining in general examines the roof fall history at Springvale Colliery, and proposes the means of preventing roof failure and controlling roof falls for Spingvale Colliery in particular.

Jan 1, 1996

By Ruxton B. P, Rhodes J. M

Two Rb-Sr ages are discernible in data concerning the leucocratic granite which is the youngest pre-sedimentation phase of the crystalline basement complex at Rum Jungle, Northern Territory, Australia. Whole-rockdata suggest that intrusion of this unit took place at about 2400 my ago, with a probable initial ratio around o·707; whole rock-potassium feldspar tie-lines indicate redistribution of strontium at about 1800 my ago. The former age correlates with other measurements on rocks which form basement to the mantling Pine Creek Geosyncline; the latter correlates also with isotopic evidence for regional metamorphism and emplacement of some younger intrusive granites elsewhere within the geosyncline. A few K-Ar ages, from scattered localities, conform generally with the later event or events which appear to have some connection with the structural deformation clearly observable both in the complex and the surrounding metasediments. It is these younger events which appear to match the residual evidence for the earliest detectable concentration of uranium minerals in the Alligator Rivers district.

Jan 1, 1977

By K. E. Tame

Pollution from radioactive nuclides, principally Ra226, in liquid waste from uranium mills can be minimized by reusing the waste solution within the mill. Such reuse of waste solution in the Vitro Chemical Co.-type process was investigated in the laboratory. Vitro employs an acid leaching process for dissolution of the uranium, countercurrent decantation for liquid-solid separation and washing, and amine solvent extraction for recovery of the uranium from solution. The simulated reuse of barren raffinate in the mill circuit was carried through two separate laboratory campaigns of 29 and 31 cycles. Conventional chloride stripping of the amine was employed in the first campaign, whereas nitrate stripping was used in the second campaign. Dissolution of uranium from the are in the acid leaching circuit averaged 96 percent. Washing efficiencies of 98 to 99 percent were attained by using 4 volume tons of combined raffinate and makeup water per ton of ore. Uranium recovery from the pregnant solution using a 5-percent solution of amine LA-1 in kerosine ranged from 99.3 to 99.9 percent.

Jan 1, 1962

A study of the swelling behaviour of a single batch of high-grade iron ore pellets during hydrogen reduction in a fixed bed showed that the extent of swelling is governed by the nucleation and growth of crystalline iron protuberances from the wüstite grains. Over the reduction temperature range 650 to 1000°C, it was found that substantial degrees of swelling can occur at temperatures in excess of 850°C, and significant variations in the swelling behaviour of individual pellets from different bed levels are observed under these conditions.The results are discussed in terms of a recent swelling theory and shown to be in general agreement.

Jan 1, 1978

By Luca de Sanctis

The analysis of piled raft foundations in layered soils may be performed by 3D finite elements or by approximate procedures. Among the latter, the code NAPRA (Russo, 1998) is based on the method of the interaction factors and accounts for soil layering by the so called Steinbrenner approximation. A comparison between the results of 3D FEM and NAPRA for some reference layered soil profiles shows that the approximation is fully acceptable for engineering purposes, provided the stiffness of the single pile is properly selected. The interest of the conclusion lies in the fact that the amount of work needed to model a practical problem by NAPRA is but a fraction of that needed by FEM modelling.

Jan 1, 2002

By G. Bartolacci, G. Couture, Levasseur. B., A. Lockhart, D. Nathan

"Pulp and froth zone characterization in a flotation circuit to improve transport of valuable minerals remains a challenge. Even though some significant breakthroughs have been made in the development of collectors in terms of selectivity, the control of gangue drainage is still the main bottleneck to achieve the production of a clean concentrate.Over the last decade, COREM’s team has been working on technologies to improve the selectivity of flotation circuits by tuning their hydrodynamic conditions using online instruments such as the bubble viewer, Jg sensor and gas hold-up. As part of its research program, COREM also developed the half-life column that establishes the relationship between the collection zone (bubble-particle attachment) and the cleaning zone (foam) of a flotation machine. In recent years, COREM has continued the development of the prototypes to make them more robust and improve the accuracy of their measurements.Recently, these hydrodynamic instruments were installed in an industrial process at Raglan Mine in order to diagnose and control the impact of hydrodynamic parameters versus the recovery and the quality of the Ni concentrate produced. Sampling campaigns of hydrodynamic parameters demonstrated that froth height could be optimized in order to increase recovery and quality of the concentrate at the same time. The specific effect of the froth height impacts both the pulp and the froth zones. Along with the impact on the drainage of the concentrate, it was observed that froth height also contributes to enhance the collection of particles in the pulp leading to an increase in metallic units.IntroductionOnce the particles of the minerals of interest are attached to the air bubbles injected in the pulp, the flotation process is driven by air dispersion parameters and froth properties. The pulp is usually responsible for the collision between air bubbles and hydrophobic particles of interest while the froth zone aims to upgrade the selectivity of the particles floated through drainage of the unwanted hydrophilic particles. Over the last four decades, flotation hydrodynamics has been extensively studied. Superficial gas velocity (Jg), gas hold-up (eg), Sauter mean bubble diameter measurements (d32) and bubble surface area flux (Sb) are among the most assessed parameters in flotation plants worldwide either to quantify the gas dispersion parameters or to optimize them (Fournier et al., 2015). McGill University has developed several sensors able to measure these parameters at industrial scale (Tavera et al., 1996; Finch et al., 1999; Chen et al. 2001)."

Jan 1, 2017

By W. G. Pariseau

Equivalent elastic properties of discontinuously jointed rock masses are computed using a non-representative volume element(NRVE) approach within a three dimensional finite element program. Joint persistence, defined as the percentage of a joint plane that is actually occupied by joint material, is used in the NRVE computations as a step towards greater realism in stability analysis of mine openings. Persistence p is also the probability that a segment of a joint plane is occupied by joint material. Computations reveal a threshold phenomenon in jointed rock mass moduli similar to that observed in percolation theory. A rapid decrease in moduli occurs above a critical value pc(about 0.6). A detailed analysis of the well-known solution for stress about a circular opening in isotropic, elastic ground illustrates the effects of joint set orientation, spacing and persistence. Although stable “on average”, joint segment failures reveal a threat to stability and point towards rational design of reinforcement or support of discontinuously jointed rock masses.

Jan 1, 2003

By Cosmin Carpinisan, Erich J. Hofmann, Stephen J. Hall

"Since presenting a technical paper regarding their unique capabilities in Forged Steel Mill Gearing at the SAG-2006 Conference, Australian heavy engineering company Hofmann Engineering has pioneered a number of new manufacturing processes and design concepts for components of large comminution equipment. These include: 1. Novel design improvements for HPGR Rolls with forged steel tyres and a unique patented tungsten carbide insert designed to improve wear life, enhance autogenous layer build-up, and to reduce breakage & chipping under load. 2. Development of forged fabricated Mill Heads using rolled & welded high-tensile steel plate as alternatives to cast conical mill heads. 3. Insitu Girth Gear measurements for profile and wear via portable 6-axis CMM. 4. Gear and Pinion designs to AGMA-6114 for SAG mills of 38’-40’ diameter to 24MW and for Ball Mills of 26’ diameter to 18MW. The paper presents case studies from the Australian heavy manufacturing facilities of Hofmann Engineering, combined with news of their new gear manufacturing and gearbox overhaul facility in Canada."

Jan 1, 2012

By Russell R. McLellan

As part of an effort to develop new or improved placer mining technology in the Tertiary gold-bearing channel gravel of northern California, the Bureau of Mines conducted investigations at the old Badger Hill placer mine in Nevada County, Calif., to collect data and information regarding drilling and sampling methods and deposit characteristics. Sampling studies involved the collection and processing of 400 tons of large-and small-volume samples from drill holes, underground workings, surface pits, and blasthole rounds. A total of 355 samples averaging 2,296 pounds per sample provided reasonably accurate data for analysis of the gold distribution. These studies indicated that the bulk of the gold is within 40 feet of bedrock in stacked, lenticular zones of cemented gravel that are largely confined to the relatively narrow, meandering course of the deepest portion of the bedrock channel. Drilling studies involved the testing of truck-mounted rotary, buckett and vibratory drills, none of which proved to be a completely versatile tool for sampling quickly and reliably both consolidated and unconsolidated gravel..

Jan 1, 1974