Search Documents

By P Craig, M Holden, C Zhang, D Foster, J Oh, S Saydam, J Liu, H L. Ramandi, S Akdag

High stress in rock masses can cause significant instability problems such as squeezing deformation in soft rock and rock bursts in hard rock. The support system applied in burst-prone areas in high-stress conditions is required to be able to carry high load and accommodate large deformation of the rock mass without experiencing any serious damage. Yielding support systems are promising to provide support for both squeezing and burst-prone rock mass encountered in mining or tunnelling at depth. They are ideally strong and stiff initially and then ductile after yielding (Potvin and Hadjigeorgiou, 2020). With respect to support design, a ground support system has to create a safe working environment under both static and dynamic loading conditions by providing the functions of reinforcing, retaining, holding and connecting elements (Cai and Kasier, 2018). Rigid rock bolts and cable bolts perform reinforcing and holding functions of a ground support system. In highly fractured ground or with large excavation spans (eg at roadway intersections or in caverns), unstable ground depth can exceed the length of typical rigid rock bolts (ie greater than ~3.0 m). In such cases, flexible cable bolts are needed to tie the reinforced and retained rock mass back to deeper and more stable rock. The flexibility of cable bolts allows anchor lengths greater than the tunnel opening that would otherwise restrict rigid bolts. Cable bolts also offer higher strength to weight ratio, with tensile strengths 2–3 times that of standard rebar bolts. This high strength comes at the cost of lower strain tolerance, typically around 5–7 per cent at break. Despite the lower strain tolerance, cable bolts are often used as dynamic support in demanding burst-prone ground conditions. The lower strain tolerance is compensated by allowing sufficient free length for stretching or incorporating a yielding device. There are a number of dynamic cable bolts available on the market and a number of testing campaigns have been undertaken to quantify the dynamic performance of these cable bolts. This paper reviews the existing range of dynamic cable bolts and discusses the potential areas for improvement and further research.

Nov 29, 2022

By W. H. Bassett

THE ease and value of the application of spectrum analysis to industrial chemistry appears to be appreciated in few of the large works laboratories of this country. For 8 years, this analysis has been of great value to the authors in both analytical and metallurgical work. To the analyst the complete qualitative analysis of an unknown alloy, revealed by a spectrogram, is a sure basis for the planning of the most direct and rapid method of attack. As the determination of each element proceeds, the purity of precipitates may be checked as often as desired. The spectrograph proves invaluable in the recognition of impurities, the separation of which would entail a lengthy and difficult procedure, or when the weight of an unknown is less than is necessary to complete the desired determinations. A few hundredths of a gram will usually suffice for spectrographic analysis. In the separation of the rarer elements, the spectrograph will show, with precision, the point where each step has been successful. In zinc of certain classes, indium, gallium, and germanium have been isolated in this way; the presence of antimony in lake coppers has been proved; and bismuth has been detected in zinc and in alloys where the presence of a few thousandths of a per cent. would be harmful. An antimony precipitate in a delicate determination may contain a considerable proportion of tin or arsenic, both of which will be revealed. The spectrograph is consequently important to the metallurgist as well as to the analyst.

Jan 2, 1922

By D A. Manhire, R M. Flores

The commercial develop of coalbed methane from the Powder River Basin has demonstrated that low-rank coals can be a viable source of gas. Currently over 20 000 coalbed methane wells exist in the Powder River and it is predicted that there will be 50 000 wells by 2010. What makes the Powder River Basin successful is the thickness of the coal (in excess of 30m) as well as the low ash content (

Jan 1, 2002

By RT White

For many years the concept of life cycle costing (LCC) was promoted for decision making in corrosion protection systems. Nevertheless, the application of LCC was limited. Input data was often sourced from suppliers and met with scepticism. As a result final analysis was often insufficiently rigorous to meet the needs of Project Managers in sound decision making. The need for expediency often resulted in non-optimal corrosion protection system specifications. With improved communications and the global reach of industries, case history data, based upon actual performance has been able to provide input to substantiate decision making. However, today?s focus upon sustainability whereby environmental, economic and even social aspects enter into decision making has extended LCC into Life Cost Analysis (LCA). In an LCA analysis energy and environmental inputs into systems are compared as part of an overall assessment. The development of Agenda 21 at the Rio summit of 1992 has challenged the countries of the world to look at sustainable development in every economic activity. This ranges from construction to mining to electricity production to automotive production, use and disposal. The protection of buildings, infrastructure and transport systems is part of the needs of sustainable development. Zinc based corrosion protection has been an important part of the arsenal of the corrosion protection industry. This paper will highlight the use of LCC and the development of LCA with reference to the use of zinc based protection systems in a number of important industries.

Jan 1, 2006

By G Njowa

Mineral resource evaluation and estimation process is not an exact science; however it depends on the knowledge and experience of the competent person and his ability to apply his mind, make reasonable assumptions, interpretations and exercise sound judgment in the mineral resource estimation process. The mineral resource evaluation results in a mineral resource statement are disclosed to investors. The minerals industry is presently undergoing rapid changes in legislation governing the public reporting of mineral assets. It has gone through different phases of development with respect to the reporting of mineral resources and mineral reserves (mineral assets). In the past no reporting was done and currently mineral assets are reported as a supplementary section that briefly describes the mineral asset termed ?the mineral reserve and mineral resource statement?. The current industry trend appears to be going towards recognition and disclosure of the mineral assets on to the balance sheet. This paper explores the salient issues behind the mineral resources and mineral reserve statement of vein and reef deposits published in the public domain. It also highlights the potential misleading consequences of these issues and which filter through to the valuation of these particular mineral assets. The creation of reporting standards in the minerals industry has made significant inroads in standardizing and consolidating the interpretation and understanding of the different classification categories in the industry in an effort to promote common interpretation towards these salient issues.

Jan 1, 2008

The occlusion of unliberated gold particles in silicates and sulfides in crushed/milled ore dictates the recovery that can be expected. The grade of this occluded gold in cyanide leach residues shows a consistent, general relationship to the head grade of the ore, irrespective of mineralogy or geographical location. The residue grade almost invariably increases with the head grade, but not in proportion to it. This phenomenon appears to stem from the nature of the geological events originally responsible for creating the ore deposits. A statistically-based technique for determining the true head grade-tail grade relationship from gold plant operating data is described. The effect is illustrated with results from several worldwide gold milling operations analyzed over the last 35 years.

Jan 1, 2008

By Felipe Amélio de Lucena

Ligas amorfas e nanocristalinas à base de ferro apresentam propriedades excepcionais, como alta dureza e resistência ao desgaste com taxa de resfriamento entre 103 e 105 K/s. Assim, este trabalho objetiva a solidificação rápida (SR) da liga à base de ferro fundido (FoFo) com adições de Boro e Nióbio, resultando na composição química (Fe65Cr17Mo2C14Si2)88B8Nb4 (%at.). A liga foi processada através de melt-spinning, no forno Discovery® Plasma e Conformação por Spray (CS) e caracterizada por: DSC, DRX, MEV e microdureza Vickers. Foram obtidos: fitas amorfas (40 µm) através de melt-spinning, chapas (1,0 e 2,0 mm) por (SR) e CS da liga (Fe65Cr17Mo2C14Si2)88B8Nb4, com depósito (1,0 e 2,0 mm) e pós overspray (20 até 180 µm). A caracterização mostrou fitas amorfas, pós overspray nanocristalinos e chapas (SR) e depósito (CS) cristalinos com as fases: Fe-a, Fe-?, Cr7C3, FeNbB e Fe2B, com respectivas microdureza Vickers de 1044 ± 102 (HV1) para o depósito CS e 1480 HV para a chapa de 2,0 mm, mostrando alta dureza.

Aug 16, 2017

By G. Onal, E. Gock, H. Dincer

"During the conventional chromite dissolution process; chromite ore concentrates were ground to at least <90 µm using the ball mill and after adding Na2CO3 and leaning material (instead of CaCO3 also residues from the leaching process) at a ratio of e.g. 1:0.75:1.2, depending on the specific formulation, follows the digestion e.g. in a rotary kiln, heated in countercurrent. The reaction time is 3 to 8 h. The calcine is comminuted and leached with water or a thin chromate solution. Depending on the type of ore used, the yield is 75-85 %. The disadvantage of the above-described process is that it is impossible, using current technology, to achieve a complete digestion of the chromite ores and that the chromium-containing residues have to be disposed of as special waste, involving a large financial effort.The subject of this study was the investigation of the effect of vibratory milling on chromite dissolution. The impact stress in the vibratory mill causes the mechanical activation of chromite, which is characterised by lattice defects. The degree of mechanical activation can be quantified by measuring the relative X-ray diffraction intensities at the parent lattice planes of chromite. Each relative X-ray diffraction ratio correlates with a certain degree of digestion. As opposed to vibratory milling, a complete digestion of chromite using a ball mill is impossible, even at extremely long grinding times.In this investigation a chromite concentrate from Pulpinar/Kayseri with content of 44 % Cr2O3 and the Eccentric Vibratory Mill was used. In order to verify the effect of the vibrating grinding on chromite dissolution, reaction kinetic investigations on digestion and leaching were carried out."

Jan 1, 2003

By Joseph Gersic

The U.S. Bureau of Mines assessed mineral resources of the BLM Malheur-Jordan Resource Areas (MJRAs) in southeastern Oregon in 1993 and 1994. The study relied heavily on acquiring and analyzing existing data. In order to efficiently handle and analyze a large quantity of data, a minerals information management program, informally called MINFO, was developed as a frontend for three databases created to store basic information gathered during the minerals resource assessment. The MINFO program will also provide the BLM with a method of tracking and updating minerals information in the future because program modules in MINFO allow the addition of new data and the correction of errors, creation of print files, transfer of data to other database formats, exportation of data to other software packages, and creation of AutoCAD script files to be used in conjunction with AutoCAD to produce maps. The report specifically identifies significant past and present mineral exploration and development activities and possible areas of future mineral exploration and development. These areas are informally designated as areas of development interest or ADIs. The report contains a scenario of what mineral development might reasonably occur in the foreseeable future if the BLM does not substantially change its present resource management plan, and it shows the possible socioeconomic impacts of that development. The uncertainty of the political and economic situation makes it extremely challenging for the USBM to accurately predict a reasonably foreseeable development scenario. The reasonably foreseeable development (RFD) scenario developed by the USBM for the BLM indicates short-term RFD of minerals should have a negligible socioeconomic impact, and longer-term RFD of minerals should have a slight socioeconomic impact on the MJRAs. The mining industry is facing a rapidly changing business and regulatory environment in Oregon. Several signal changes have occurred recently, including State regulations that require significant bonding prior to the startup of "chemical process" mining, an initiative by a special interest group to stop all chemical process gold mining within the State, and an opinion by the Oregon Attorney General (AG) banning all forms of placer mining without exemption. In the AG opinion, not even gold panning is allowed, and the prohibition applies to mining claims on Federal lands. The State legislature may amend the statute to allow small scale placer mining to occur, as was allowed under an AG opinion issued in 1982. These and other changes occurring at the local, State, and National levels are making it more challenging for the mining industry to operate in the United States. Several epithermal gold properties in the MJRAs attracted the mining industry&apos;s interest. Only the Grassy Mountain Project of Newmont Grassy Mountain Corporation may be developed in the next few years. It is probable that at least two other properties will be developed if Grassy Mountain is successful. Mining companies are waiting to see the effect recently promulgated State mining regulations and more stringent proposed regulations, particularly bonding regulations, may have on Grassy Mountain. Resources of bentonite, diatomite, and zeolite are abundant. The almost Ubiquitous stone, sand and gravel, and semiprecious gemstone resources also were examined. Little environmental or socioeconomic impact is expected from reasonably foreseeable development of these mineral resources.

Jan 1, 1994

Jan 1, 1966

By Phillip Martin Warren

Safety and productivity are critical factors in the performance of the Australian Mining Industry. In this sense, the paper point out that while the multiple dimensions of both training and productivity make it difficult to quantify the relationship, it is clear from this study that organizations that conduct training consider that there is a very positive link. Training is seen as a very important activity by the vast majority of organizations surveyed, and is an activity from which they consider they are gaining significant, and often very substantial productivity benefits. Therefore, it predicts well for productivity of Australian enterprises which invest in training.

Sep 13, 2001

By P. Klaus

"KfW IPEX-Bank is the commercial arm of KfW Bankengruppe, responsible for international project and export finance.KfW was one of the first banks in Germany to promulgate environmental guidelines for its commercial business activities. These guidelines were first made public in 2000 and updated for the second time in 2004. They now include specific reference not only to environmental but also to social concerns. The guidelines specify the procedures to be followed in assessing credit risks related to environmental or social hazards.The bank considers sustainability as an interdependent framework of economic, ecological and social factors. In its efforts to contribute to sustainable development worldwide the bank uses its influence as far as possible to improve a project’s performance if such improvement is deemed necessary."

Jan 1, 2005

By Vladimir I. Ryaboy, Konstantin M. Asonchik

"At flotation of sulfide-barite ores of one of deposits sulfide and barite concentrates are obtained. In sulfide cycle potassium xantogenate as a collector in consumption of 200 g/ton, methylisobutylcarbinol (MIBC) as a foaming agent in consumption of 30 g/ton and also liquid glass are used. In barite cycle tall oil as fatty acid collector in consumption up to 400 g/ton is used.Sulfide concentrate represents mainly gold- and silver-containing pyrite. The contents of gold makes not less than 10 g per ton, silver - not less than 278 g/t. Barite concentrate contains up to 86% of barite.Factory is working in water recirculation conditions. Owing to that in barite cycle fatty acid collector is used, technological water from tailing repository contains fatty acids soap up to 25 mg/l. Before submission into sulfide cycle this water is conditioned with active carbon to delete the main part of fatty acid collector. The active carbon consumption makes 0,4-0,5 kg per 1m3 of water or 1,5-2 kg per ton of ore. The above mentioned consumption of active carbon improves reducing of contents of fatty acid collector from the initial concentration of 25-30 mg/l to 4 mg/l. At concentration 4 mg/l fatty acid collector does not render negative influence on flotation index in sulfide cycle. At the absence of active carbon pollution of sulfide concentrate and its irrevocable lost are observed."

Jan 1, 2003

By P González, J Videla, E Córdova, I Gottreux

Currently, underground mining of deeper massive deposits with lower grades, harder rock conditions in high strength environments, entails difficulties in caving, fragmentation and seismicity of the orebody.So far, the use of preconditioning (PC) with hydraulic fracturing (HF) has shown positive results in terms of seismic response and caving performance, while PC combined with explosives aims to weaken the rock mass, causing an additional effect on fragmentation.In particular, mines commonly referred to as ‘supercaves’, operated by caving methods, have the need to integrate mine to plant processes, where rock fragmentation appears as a key tool. In fact, it implies making mining and comminution processes more efficient to the plant and for mines, it justifies the search of innovative solutions in drilling and blasting techniques to precondition the rock mass. The following paper aims to show the feasibility of numerical blast modelling to weaken the rock mass using explosives, mainly through sensitivity analysis applied to designs to minimise bias and uncertainty in the results. It is shown how the presence of structures, their geometry and in situ stresses influence or interfere with the PC method being used.From the work, it is concluded that better knowledge on the application of explosives weakening allows specialists to strengthen numerical models associated with every design and therefore previously validate their applicability, helping to understand complex phenomena such as the propagation of mechanical waves in non-elastic heterogeneous media. In this sense, it is understood that while there are studies (Sanchidri&#225;n, Segarra and L&#243;pez, 2006) showing that the transfer of energy in the rock mass could be even greater in a confined environment, the more competent rock mass and higher in situ stresses interfere mostly on the effectiveness of a technique using explosives.CITATION:Gottreux, I, C&#243;rdova, E, Gonz&#225;lez, P and Videla, J, 2016. Preconditioning modelling and explosives effectiveness in block caving, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 683–688 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

By Qiuyang Hong, Bo Li, Dongyun Liang

"A weathering-crust niobium-rare earth-bearing deposit is formed by the weathering alterationof alkaline granite, which is refractory due to its low grade and complex properties. The mineralogicalcomposition of ore, the grain size of majorminerals as well as the occurrence of Nb and REE are studied in this paper using MLA combined with traditional methods. According to the results, a wide range of Nb-Ti-REE compound minerals including titanoniobite, uranpyrochlore, chlopinite, samarskite and ilmenorutile areformed for the extensive isomorphous substitution among the elements of Nb, Ta, REE, Fe, Ti, U and Th. The occurrence of REE is extremely complex. First, the REEexistingas rare earth minerals including monazite, xenotime, bastnaesite,etcaccount for 21%. Second, the REEexist in the lattice of Nb and Zr minerals as isomorphous additions, which account for 18%. Third, the REE exist as colloidal rare earthdeposit,which account for 35%. Last, the REEexistingas ion-adsorption-type rare earth,which are adsorbedon the kaolinite in the form of hydrated hydroxyl ions, account for 26%.Based on the results of mineralogy, the combined technology process "mineral processing- hydrometallurgical separation" is needed to deal with the ore. The mineral processing tests show that, for the feed ore containing Nb2O5 0.065%, REO 0.13%, an Nb-REE concentrate containing Nb2O5 1.38%, REO 1.98% can be gained by "high intensity magnetic separation-regrinding-gravity separation by shaking tables". The recovery of Nb2O5 and REO is 62.42% and 44.78% respectively. The Nb-REE concentrate is dealt by the metallurgy process "direct reduction- acid leaching & acidulating- neutralization & precipitation- chlorination & distillation" and the rare earth oxide of 92.34% REO as well as the Nb-Zr oxide of 24.62% Nb2O5 can be obtained with the recovery of REO and Nb2O5 being 76.83% and 59.37% respectively."

Jan 1, 2014

By Gungor Tuncer, Ali Kahriman, Abdulkadir Karadogan, Umit Ozer, Ertugrul Kaya, Kagan Ozdemir

The results of bench blasting on quarries, have important influences on the performance of subsequent mining activities such as loading, hauling, crushing, grinding etc., and the total costs of that mine. Drilling and blasting is an important step in mine producing chain and its results such as fragmentation, muckpile shape and looseness, dilution, damage and rock softening effect the efficiency of downstream processes. Within the scope of this study, the three different hydraulic excavators’ working performances have been studied considering the particle size distribution after bench lasting at a quarry in Istanbul Turkey. Five shots have been realized on the quarry and average particle size of muckpile after each shot were assessed by digital image analysis method. Bucket loading times have been measured by stopwatch study after five shots. Excavator bucket loading times were also estimated by bucket loading time estimation formula which was published in ISEE 2007 Conference, Ozdemir et al. 2007. Estimated and measured times have been statistically analyzed and the accuracy rate of formula has been determined for five events.

Jan 1, 2008

By A. A. Dor

Recent developments in the design of concentration plants have reflected the increased recognition that has been given to the economic and metallurgical advantages of autogenous grinding. This has manifested itself in the increasing adoption of primary auto genous grinding in iron ore &apos;beneficiation plants in North America. Table 1 lists eleven major iron ore beneficiation plants which have either been put in operation since 1961 or are under construction at present. Seven out of these eleven plants have adopted primary autogenous grinding. Four of them have coarse grinding mills (8 to 14 mesh) and three have fine grinding primary circuits (48 to 65 mesh). Their nominal capacity totals 26. 2 million ltpy of concentrates or pellets, representing very nearly 75% of the aggregate capacity 135. 3 million ltpy) of the eleven concentrators listed. For a long time there was a tendency to consider that primary autogenous grinding was only applicable to suitable coarse grained ores, However, extensive testing of a very wide variety of ores, and actual operating performance in several commercial plants, seem to have established beyond reasonable doubt, that the majority of mineral ores which the beneficiation engineer may be called upon to process can be ground autogenously. The basis for the selection of autogenous or conventional grinding mills, becomes principally economic and depends on the liberation characteristics of the ores under consideration and their relative hardness and grindability.

Jan 1, 1965

By Elaine T. Cullen, Thomas W. Camm

The mentor/learner model is a time-honored approach to teaching, including within the mining industry. Miners know when they see excellence and have a deep respect for experts in their field. By using expert miners as mentors to other, less-experienced miners, training programs can be developed that will have a legitimacy and credibility that resonates with those being trained. Building upon concepts in current theories of adult education, this paper highlights the unique advantages of using mentoring as a teaching method that can make the educational experience both interesting and effective. Current NIOSH safety training materials use these concepts to deliver effective adult learning experiences for workers in the mining industry.

Jan 1, 2002

The 99th Annual General Meeting of The South African Institute of Mining and Metallurgy was held in the Gold Room, Transvaal Automobile Club, 60 5th Street, Lower Houghton, Johannesburg on Wednesday, 14th August, 1996. Obituaries The President announced the death, during the year, of the following members: Life Fellows H.L. Munro, H.S. Simpson, P.L. Ward Fellows I.M. Hossy, A.E. O&apos;Meara Retired Fellows E.A. Arvidson, R.F. Bourne, F. Hawke, W. Lloyd, J.M. Meyer Members J. Allen, P.A. Boardman, L.M. Jacobs, G.F. Marx, G.D. Perry, R.W. Spraggs Retired Member M. Milner Associate I. Pieterse. In memory of the deceased and in sympathy with the bereaved, all rose and observed a moment of silence.

Jan 1, 1996

Recovery of Vanadium from Stone Coal Through an Environmentally Friendly Acid Leaching Technology

Sep 13, 2010