Search Documents

By R. S. Dean

"Applied Mineral Physics, by R. S. Dean.- This is an introduction to the seven papers that follow. It discusses the practical aspects of mineral physics and outlines the theo¬retical viewpoint underlying the investigations reported herein.Explosive Shattering as a Possible Economical Method of Ore Presentation By John Gross and C. E. Wood. - It is shown that explosion shattering by impact is favored by large charges and by low ratio of water to charge. For 400-gram charges of dolomite crushed through 48 mesh the steam costs are less than 5 cents per ton of dolomite obtained. This is within the range of present steam costs for ball-milling dolomite.Electrical Properties of Minersl Aggergates I. Natural and Artificial Aggregates Crystallized Lead Sulphide By R.S. Dean and John Koster - This paper deals with the electrical properties of natural and synthetic galena. It is shown that massive crystalline galena has a normal positive temperature coefficient of resistance, whereas fine-grained steel galena has a negative temperature coefficient, the curve R v. T being exponential in form. That steel galena behaves somewhat like a leaky condenser is indicated by ballistic and alternating-current bridge measurements. In determining the cause of the erratic results of alternating-current resistance measurements it was observed that the measured re¬sistance was a function of the current through the specimen. The direct-current resistance was found to be proportional to the square of a superimposed radio-frequency current and independent of the frequency.The influence of grain size or the amount of metallic interface on the voltage-current characteristics at various temperatures on synthetic galena pastilles was studied. It is proved that the volts v. amperes curves are linear for all sizes and temperatures, that they have an intercept which is apparently a linear function of the temperature, and that their slopes are exponential functions of the temperature and give rise to a negative temperature coefficient of resistance.Apparatus for determing the Magnetic Constants of Mineral Powders by V,H, Gottschalk,and C. W. Davis.- A modified isthmus permeameter having a spark-suppressed primary and a multiplier in the secondary circuit to regulate the effect of capsules functioning as a twin isthmus is used to obtain quantitative data and normal induction and hystersis curves from small amounts of powdered material at fields surpassing 3.000 oersteds. Data and curves are given to demonstrate the calibration of the apparatus and the reproducibility of its results. Applications and limitations of the apparatus are noted.Magnetization Curves for Magnetite Poeders by V. H. Gottschalk and F. S. Wartman.- This paper gives measurements on four lots of purified and analyzed magnetites in mixed fractions with especial reference to the variation of permeability with grain size and with dilution by an inert material."

Feb 1, 1935

By Mark Jolly

"Instead of using the traditional batch casting process, the CRIMSON [1] (Constrained Rapid Induction Melting Single Shot Up-Casting) method employs a high-powered furnace to melt just enough metal to fill a single mould in a closed crucible. The crucible is transferred to a station for computer-controlled counter gravity filling of the mould for optimum filling and solidification. The CRIMSON method therefore holds the liquid aluminium for a minimum of time drastically reducing the energy losses attributed to holding the metal at temperature. With the rapid melting times achieved, of the order of minutes, there isn’t a long time at temperature for hydrogen to be absorbed or for thick layers of oxide to form. The metal is never allowed to fall under gravity and therefore any oxide formed is not entrained within the liquid. Thus higher quality castings are produced leading to a reduction in scrap rate and reduced overall energy losses.IntroductionEngineers at the University of Birmingham, England, with local company, NTec, have invented a new casting process that will reduce the energy costs of light-metal foundries. The technology, entitled CRIMSON, means that foundries need only heat the quantity of metal required to fill a single mould rather than large batches that use unnecessary energy and create waste. The complete concept of CRIMSON requires a change of philosophy in the approach to casting and requires the user to think holistically in order to reap the full benefits from the process. This paper will discuss the various aspects of energy wastage within the foundry sector and discusses the processes whereby the energy can be reduced. Primarily the author focuses on the aluminium sector but CRIMSON can be applied to many of the non-ferrous “light” alloys. Ferrous materials and non-ferrous “heavy” alloys can also benefit from some of the ideas but not necessarily directly from the application of CRIMSON."

Jan 1, 2010

By K. L. Williams

The Bureau of Mines laboratory tested the response of a commercially available real-time aerosol monitor (GCA RAM-1) to various dusts. Monitor measurements were recorded, averaged, and compared with simultaneous gravimtric measurements of each test dust. Tests usually lasted several hours. The test dusts of various particle size distributions used included coal, limestone, and a commercially available test dust. For each particular dust, the monitor response was linear and correlated well with mass concentration over the range of about 0.5 to 10 mg/m3. The monitor can estimate a 2.0-/m3 respirable coal dust concentration within as little as 26 pct with 95 pct confidence. The monitor must, however, be calibrated with the dust to be measured because the instrument response is affected by the type of dust particle. The average monitor response to same mass concentration of coal dust was approximately twice the average monitor response to the same mass concentration of limestone dust.

Jan 1, 1984

By S. Solar, G. Tiess, K. Nielsen, H. Wagner

The paper summarises the results of a recent study of minerals planning policies of the Member States of the EU. The study has shown that contrary to the public opinion the production of industrial minerals and construction minerals is significant the former accounting for about 20 percent of global production, the latter amounting to about 3 billion tonnes per annum. In contrast the importance of metal ores has diminished although metal production in some European countries can still be significant. The study revealed that very few Member States have clearly defined mineral policies. Common to most mineral policies is the emphasis on reducing minerals consumption and recycling whereas the important aspect protecting access to minerals resources is not adequately addressed by most policies. Access to mineral deposits is regulated in most Member States by land use legislation and administration. Information on mineral deposits in land use planning data bases tends to be scarce. This together with the absence of formal mineral policies places minerals at a disadvantage in land use decision making. The emergence in the recent past of environmental legislation and in particular environmental impact assessments has had a crucial effect on the duration of the authorization process for new mineral projects. Examples are given how minerals planning is handled in some of the Member States.

Jan 1, 2005

By R. A. Meister

The study on improving surface coat refuse disposal site inspections included surface inspections of 15 refuse disposal sites. Monthly aerial photos were taken of the sites and computer methods were used to determine elevation changes. Photogrammetric techniques that were used are described in detail. A comparison of the results of each of these inspection techniques is included. A detailed evaluation of the photogrammetric techniques was made and conclusions were drawn concerning the advantages and disadvantages of using aerial photography and photogrammetry as part of the inspection procedure. Operators' opinions of the aerial photography methods are included.

Jan 1, 1980

By A. Burger Pintér

To be meaningful the sharing of ideas about the National Environmental Management Act (NEMA) and social issues within the context of Mining and Metallurgy (M&M) requires an honest scrutiny of the M&M/social environment relationship, both past and present. It is not a secret that this relationship has been and is fraught with difficulties. Thus from all perspectives (M&M, society and environmental and social consultants) such a dissection, that highlights the realities, both good and bad, is uncomfortable. For this section of the colloquium to have any value, the honest but difficult approach needs to be taken.

Jan 1, 2000

By Alice H. Zhu

Belt conveyors are widely used in materials handling industries. The bulk materials which can be transported include ores, coal, earth, grain, limestone, wood chips, fertilizer components such as potash and many others. Along with the new technology development and enhanced industrial automation requirements, belt conveyor instrumentation has also been modernized to improve conveyor availability and performance. Traditionally, belt conveyors are equipped with emergency pull cord switches to shut the conveyor down, misalignment switches to signal the belt offline condition, speed sensors to detect the belt slippage, and level switches to prevent material plugging in the discharge chute. Belt rip detectors are also normally provided for long belt conveyors. As a rule, equipment condition monitoring is not automated at most operating facilities, but is performed manually by maintenance staff via time-based surveillance. The new generation of condition monitoring instrumentation and control equipment can be successfully utilized to design a reliable, cost-effective, and centralized monitoring system, capable of monitoring a wide variety of mechanical equipment. The implementation of the condition monitoring automated system can provide continual monitoring of the plant equipment to ensure safe operation of the equipment to its required capacity. Any abnormal behavior of the motors, gear reducers and pulleys can be analyzed, alarmed, and recorded immediately, so problems can be detected and resolved before critical components failure. Therefore, the current trend is to provide the belt conveyors with condition monitoring system in addition to the traditional instrumentation, where temperature probes and vibration sensors can be installed on motors, gear reducers and all pulleys. Another innovative development is a three-in-one type belt rip detector which combines laser, tray and cord type detection together to ensure a prompt belt tear indication. The purpose of this paper is to present the latest development of belt conveyor instrumentation and introduce the application of newly developed instruments.

Nov 1, 2011

By F. H. Abd EL-Rahiem

A selective dispersion process is presented and the work carried out to find optimum process conditions to minimise the colouring material in ground calcium carbonate (GCC) is described. The feed material is the overflow product from a hydrocyclone which results from using a Denver Attritioning machine with semi-autogenous grinding for one hour and a 1:1 ore/water ratio. By using sodium silicate (SS), with pH 9 and pulp density 5%, the iron content (as colouring impurities) is decreased from 0.21% in the original concentrate to 0.12% in the final concentrate. The degree of whiteness reached is improved to 85% from 63% in the original material. However, by using hexametaphosphate (SHMP) at pH 10 at the same pulp density, the iron content decreased to about 0.073% and hence the whiteness degree increased to about 96%.

Jan 1, 2004

"11.1. IntroductionThe recovery of platinum-group elements (POE) from ores is a subject which has received almost no mention in the literature. Edwards (1975) refers to the process used for refining of the POE, throughout the Western World, as a so-called ""conventional"" process .... ""not because of the simplicity or convenience of the operations, but more probably because of the inertia of established processes and the aura of secrecy with which the major platinum refiners have surrounded this process."" There is no doubt in this writer's mind that the latter is also applicable to the dearth of knowledge of the mineralogy, geochemistry and ore deposits of PGE and that the poor recoveries, mainly attributed to the mineral beneficiation stages of concentration, are also affected by this traditional secrecy. Fortunately, this attitude is changing, due no doubt to the advantages that accrue from more open research which may be critically assessed in the literature in the traditional manner. Examples of this more open approach to recoveries and recovery problems are represented by Newman (1973), who gave some typical recovery percentages for Merensky Reef ores, and the recent encouragement and cooperation on mill samples from the Sudbury area by lnco Metals Company (cf. Cabri, 1981a).In general, platinum-group elements are recovered from an ore by the use of a physical concentration method, such as gravity separation or flotation, followed by further upgrading using further physical, wet chemical or pyrometallurgical techniques. The final process of refining in which the individual platinum-group elements are produced in pure form is outside the scope of this chapter.Platinum-group element deposits naturally fall into different categories according to the recovery process best suited for them, viz. those amenable to gravity separation, those amenable to flotation, and those where platinum-group elements are by-products of base metal sulphide, chromite and miscellaneous other deposits."

Jan 1, 1979

In this paper, uniaxial compression tests were conducted on intact rocks and broken rocks that were reinforced by grouting, and the effects of grouting on the strength of broken rocks were analyzed. The results show that after grouting reinforcement, the bearing capacity of broken rocks with different lithologies increased, and their uniaxial compressive strength recovered by approximately 6%–16%. The results indicated that the stronger the rock, the smaller the strength recovery of the consolidated body formed after grouting. At the same time, using borehole camera observation and deep overburden strata separations, the fracture development characteristics of surrounding rocks of the gob-side retained entry were analyzed and divided into different regions. On this basis, a guided grouting method was proposed; that is, shallow hole grouting was first used in the plastic zone of the broken surrounding rocks to form the isolation layer, and then deep grouting holes were arranged in the elastic-plastic zone of the transition zone to guide the slurry flow to the shallow unfilled zone. Therefore, the broken surrounding rocks were reinforced into an integrated body and selfbearing capacity improved.

Jul 28, 2020

By Ogden Tweto

The Leadville district, on the west flank of the Mosquito Range in central Colorado, has produced silver, zinc, lead, gold, and minor metals valued at $512,000,000. The ore deposits are in a sequence of dolomites and quartzites, Cambrian through Mississippian in age and about 500 feet thick, which is extensively intruded by porphyry sills, dikes, and plugs of Tertiary age. The sedimentary rocks and sills dip about 15°E and are broken by many faults, which are predominantly of nearnorth trend and downthrown to the west. The ore deposits are principally blanket or manto replacement deposits, but in the eastern part of the district many veins occur also. The replacement deposits are largely confined to three dolomite units in the stratigraphic sequence. Of these, the uppermost or Leadville Dolomite is the most productive. Most ore bodies are on the underside of porphyry sills and, particularly, beneath sills that occupy unconformities. Many replacement bodies have vein roots or branch from veins. The veins occupy faults and are productive mainly in the section of quartzites and dolomites and included sills. The primary ores consist principally of pyrite, marmatitic sphalerite, and galena but locally contain chalcopyrite, silver minerals, bismuth minerals, and gold. Principal gangue minerals are manganosiderite and jasperoid. The ore deposits have a crude zonal pattern centered around an intrusive center at Breece Hill, which evidently influenced ore deposition thermally. The ore deposits were oxidized to depths of several hundred feet in Miocene time. Bonanza ores mined in the early days were characterized by cerussite, cerargyrite, and embolite. Later, zinc carbonate ores were identified and mined on a large scale. The Leadville district is a complexly faulted and intruded area at the intersection of major fault systems trending N20°W and N15°E in the Mosquito Range. The intensely fractured area evidently localized igneous intrusion and subsequent mineralization. Ore solutions rose on many of the faults in the area, presumably from the same source as the porphyry magmas. Movement on these faults continued into the Pleistocene, displacing ore bodies, oxidation zones, Pliocene sediments, and glacial deposits.

Jan 1, 1968

By William G. Pariseau

Few departments of mining, metallurgical or petroleum engineering in the United States have critical mass. Cost per student credit hour (SCH) in departments across the country are usually the highest among engineering departments, which are the highest on campus. Almost all departments are operating at fixed costs and enrollments could easily double without incurring much additional cost. However, the cost per SCH would remain unacceptably high and the probability of doubling enrollment is nil. Declining enrollment is a more likely future. The pressure to reduce SCH from university administration is unrelenting. And it has the potential for doing serious damage to program quality when standards and requirements are lowered in attempts to maintain enrollments and increase retention.

Jan 1, 2002

By I. E. Teymenson, L. A. Bakhvalov

Irrational usage of mineral commodities leads to depletion of natural resources and various ecological violations in natural environment. Fulfilment of a number of measures and strategic decisions by given problems requires a correct forecast of trends of social-economic systems. For solving the task of long-term forecasting special procedures, considering Kondratyev’s big cycles of world conjuncture, have been embedded into algorithms of unknown parameters identification and recovering of factors of different countries mineral resources production and consumption models. In the paper the classification of long cycles types, existing forecasting algorithms on the basis of Kondratyev’s ‘long waves’ or ‘K-waves’ and the modified algorithm, developed by us, which allows to reduce time and financial expenses and to improve the forecast quality, are presented. Furthermore, the article includes several forecasts of mining branch corrected models factors, received by us, permitting complex prognosis of economic and social development of different scale and control level systems. In the paper workability of proposed forecasting algorithms on the base of ‘K-waves’ and adequacy of created models to researched processes are proved.

Jan 1, 2003

By Dean H. Ambrose

This paper presents the results of a study using computer human modeling to examine machine appendage speed. The objective was to determine the impact of roof bolter machine appendage speed on the likelihood of the operator coming in contact with. A contact means two or more objects intersecting or touching each other, e.g., appendage makes contact with the operator?s hand, arm, head or leg. Incident investigation reports do not usually contain enough information to aid in studying this problem and laboratory experiments with human subjects are also not feasible because of safety and ethical issues. As an alternative, researchers developed a computer model approach as the primary means to gather data. By simulating an operator?s random behavior and machine?s appendage velocity, researchers can study potential hazards of tasks where it is not possible to perform experiments with human subjects. Analysis information is helpful to the mining industry in terms of making recommendations that reduce the likelihood that roof-bolter operators experience injury due to contact with a moving boom. Data analysis of roof bolter simulations show that the virtual-operator?s response time has little effect on the number of contacts experienced. Based on frequency and cross-tabulation, regardless of other variables, contact incidents were always greater when the boom was moving up, were always greater on the palm, and were always greater for the boom part of the machine. Also, regardless of boom speed, the 25th-percentile-sized operators experienced more contacts than did other operator sizes. Furthermore, regardless of boom speed, the 152-cm mine seam experienced more contacts than did other seam heights tested. Results of a survival analytic approach suggest that controlling the boom speed is the most important factor in determining the risk of an operator making contact. Based on the data collected, boom speed greater than 41 cm/s results in a substantial increase in risk to the roof bolter operator and should probably be avoided. At speeds less than or equal to 25 cm/s are associated with a more modest relative risk, which represents an acceptable level of risk. Also, at speeds between 25 and 41 cm/s, there could be a particular boom speed in this range at which a significant inflection point in the relative risk estimates occurs. Based on the results, this issue needs to be addressed by future research.

Jan 1, 2003

By Kwang ‘Min’ Kim, Paul T. Behum

The Old Bevier Aerobic Wetland in Macon County, Missouri, was constructed between 1990 and 1991 by the Missouri Department of Natural Resources’ Land Reclamation Program for the purpose of treating acid mine drainage (AMD). The principal source of the AMD is from an underground mine that operated during the 1920's through 1950's, which was partially exposed during surface mining in the 1960’s. Limestone bedding of an AMD collection system provided alkalinity similar to an anoxic limestone drain (ALD). Because the original aerobic wetland failed when a critical dilution water supply became unavailable, the total acidity of the AMD overwhelmed the limited neutralization ability of the aerobic wetland. The aquatic vegetation deteriorated and treatment became ineffective. The Missouri Land Reclamation Program with the assistance of the Office of Surface Mining, Mid-Continent Regional Coordinating Center rehabilitated the Old Bevier Aerobic Wetland in 2001, incorporating newer technologies to improve the performance. The new system, Old Bevier II treatment facility, consists of a 2-stage vertical flow pond (VFP) with associated oxidation cells and aerobic wetlands. This paper discusses the performance of this passive AMD treatment system, updating an earlier report. The new treatment system has operated with nearly continuous net alkaline discharge and a high iron removal rate. Treatment improves during warm months when emergent vegetation is fully established and biologic activity is greater. Reduction in system efficiency is evident during winter months.

Jan 1, 2005

By Elizabeth A. Johnson

The vaporization thermodynamics of the aluminum-silicon carbides Al4SiC4 and Al8SiC7 were studied by the Bureau of Mines over the temperature range of approximately 1,500 to 1,700 K. Vapor pressures were measured by a Knudsen effusion-mass spectrometry technique in which powdered samples were effused from graphite crucibles through small orifices. For each compound, a total of six orifice diameters was tested to verify equilibrium within the cell. Aluminum, mass number 27, was the only vapor species detected over the range 4 to 200 amu. Experimental results are based on the following equations for incongruent decomposition: A14SiC4(cr) - 4A1(g) + SiC(a,hex) + 3C(gr); Al8SiC7(cr) - 8A1(g) + SiC(a,hex) + 6C(gr). The observed vapor pressure-temperature relationships determined with a cell orifice area of 2.0 x 10-3 cm2 for Al4SiC4 and 1.81 x 10-3 cm2 for A18SiC7 are the following: Log P - (-18,682/T) + 12.476, for Al4SiC4 (1,550 to 1,643 K) and Log P = (-19,308/T) + 12.421, for Al8SiC7 (1,526 to 1,784 K), with P in pascals and T in kelvins. Third-law analysis of the data provided the following heats of formation: A14SiC4 ?H at 298.15 K - -50.0 kcal/mol and A18SiC7 ?H at 298.15 K - -92.1 kcal/mol.

Jan 1, 2011

By Thomas B. Borak, Keith J. Schiager, Janet A. Johnson

OBJECTIVES OF RADIATION MONITORING Monitoring is a tool used in the practice of radiation protection. The primary reasons for monitoring are to reduce radiation exposures to levels that are as low as reasonably achievable and to assure that no individual receives a dose exceeding the maximum individual dose limit. The documentation of radiation doses for legal, medical, or epidemiological reasons is a subordinate function of any monitoring program. The investment in radiation monitoring programs should be guided by four criteria: (1) the detection and avoidance of unnecessary exposures, (2) the magnitude of potential health risks, (3) the determination of combined doses and risks with adequate confidence, and (4) the verification of compliance with established limits. FIRST CRITERION: DOSE REDUCTION - DETECT AND CORRECT UNNECESSARY EXPOSURES The system of dose limitation advocated by the International Commission on Radiological Protection (ICRP, 1977), and subscribed to in a broad sense by various regulatory agencies, is comprised of three essential ingredients: (1) [justification] of any practice that produces radiation doses by some commensurate net benefit, (2) [optimization] of radiation control measures by reducing doses to levels that are as low as reasonably achievable, and (3) [limitation] of individual doses to preclude inequities and [moldistribution] of risks. All too often, only the third criterion - the limitation of individual doses to prescribed regulatory limits - is explicitly addressed in everyday radiation protection programs. The emphasis of most exposure control and monitoring efforts appears to be directed toward limiting and documenting individual doses that might approach the legal limit. The first two criteria, i.e. justification and optimization, should contribute to a rationale for allocating monitoring efforts. When applied to individuals, these criteria mean the detection and elimination of unnecessary exposures. This should be a high priority of any monitoring program. Measurements should be directed toward detecting inoperative or ineffective control measures, whether or not there is a risk of exceeding the individual dose limits. The ICRP recommends a procedure that can be used effectively to reduce unnecessary exposures. A n investigation level should be established at an exposure rate substantially lower than the regulatory limit, e.g. 30% of the limit (ICRP 26, 1977, p.33). Measurements obtained during routine monitoring that exceed the investigation level are evaluated with respect to cause and potential reduction. To be effective, the evaluation results should be formally recorded and conveyed both to management and to the workers involved. Although the investigation level recommended by the ICRP is based on a fixed exposure rate or derived air concentration, an equally effective evaluation program may be based on the investigation of a percentage of all measurements. For example, one might investigate the highest 5% or a random selection of all measurements. In any case, the objective is to detect and correct situations that are producing unnecessary exposures. SECOND CRITERION: MONITOR IN PROPORTION TO THE MAGNITUDE OF RISK The ICRP criteria apply generally to all radiation exposures. However, a second priority for monitoring programs should be established on the basis of the nature of the exposures and the magnitude of the health risks involved. Current practices in radiation protection are based on dose limits to specific organs and assessment of individual exposure pathways, with little consideration of the combined doses from various pathways. Although the intent of the ICRP recommendations was to limit the total dose to each critical organ, combined doses from external and internal sources are rarely determined. The recent recommendations of the ICRP (Publ. 26, 1977) are based on the limitation of total health risk from occupational radiation exposures. Implementation of this concept would necessarily require the measurement, calculation and summation of doses and concomitant risks to all organs of the body from all exposure pathways. The U.S. Environmental Protection Agency has taken the first step toward translating the ICRP recommendations into regulations. The proposed recommendations for Federal Radiation Protection Guidance for Occupational Exposures (USEPA, 1981) include provisions for summing the risk-weighted organ doses to determine compliance with an effective whole-body dose equivalent limit. Whether or not the proposed guidance is modified before final adoption, it seems clear that some version of dose summation and combined risk limitation will be included in future regulations. With this

Jan 1, 1981

By M. R. Shahan, C. E. Seaman, Mischler S. E., T. W. Beck

"Float dust deposits in coal mine return airways pose a risk in the event of a methane ignition. Controlling airborne dust prior to deposition in the return would make current rock dusting practices more effective and reduce the risk of coal-dust-fueled explosions. The goal of this U.S. National Institute for Occupational Safety and Health study is to determine the potential of open-air water sprays to reduce concentrations of airborne float coal dust, smaller than 75 µm in diameter, in longwall face airstreams. This study evaluated unconfined water sprays in a featureless tunnel ventilated at a typical longwall face velocity of 3.6 m/s (700 fpm). Experiments were conducted for two nozzle orientations and two water pressures for hollow cone, full cone, flat fan, air atomizing and hydraulic atomizing spray nozzles. Gravimetric samples show that airborne float dust removal efficiencies averaged 19.6 percent for all sprays under all conditions. The results indicate that the preferred spray nozzle should be operated at high fluid pressures to produce smaller droplets and move more air. These findings agree with past respirable dust control research, providing guidance on spray selection and spray array design in ongoing efforts to control airborne float dust over the entire longwall ventilated opening. IntroductionCoal mining processes produce airborne dust that naturally deposits on the floor, roof and ribs of mine airways. These fine dust particles, termed float coal dust when smaller than 75 µm in diameter, are deposited in the return entries of coal mines and can be reentrained by pressure waves induced by methane-air explosions (Rice et al., 1911; Nagy, 1981; U.S. National Institute for Occupational Safety and Health (NIOSH), 2006). These particles are also those most likely to participate in coal-dust-fueled explosions, which can potentiate and propagate explosions resulting in extensive damage. In order to meet compliance requirements of at least 80 percent incombustible content in the composition of material deposited in mine entries (U.S. Mine Safety and Health Administration (MSHA), 2016), coal mines apply an inerting agent, specifically, rock dust (Harris et al., 2009). Should methane be present in the mine atmosphere, the required fraction of incombustible content is further increased by 0.4 percent for each 0.1 percent methane. The removal of airborne float coal dust (AFCD) prior to deposition is an approach intended to make current rock dusting practices more effective by increasing the proportion of inert material to combustible material, resulting in a lower risk of coal-dust-fueled explosions."

Jan 1, 2018

By J. C. Cawley

This National Institute for Occupational Safety and Health study was conducted to focus future research on the most significant electrical problems in the mining industry. Data from 1,926 mine electrical accidents (including 75 fatalities) that occurred between 1990 and 1999 were studied. Coal and metal-nonmetal operator- and contractor-reported data are presented. All data used in this analysis were MSHA closeout data, except 1999, which were preliminary data. Electricity was the 4th leading cause of death reported in mining despite being the 14th leading cause of injuries. Electrical shock, not electrical burns, caused 70 of the 75 electrical fatalities reported. About one-half of mine electrical accidents and fatalities occurred during electrical maintenance. Suggestions for mitigating electrical hazards are proposed.

Jan 1, 2002

By G. T. Lineberry, W. J. Wiehagen

A Paradigm Shift As market economists, mine managers are interested in "staying in business" and even "prospering." Bottom-line results are the "order of the day." Concern for bottom-line results invokes questions such as: How much was produced? At what cost? And, was anyone injured? While these questions will always carry everyday emphasis at the mine, they are fundamentally lacking in that they often appear, especially to lower levels of management and to the production worker, as preeminent concerns. Driven by market economics, many organizations have decentralized, outsourced, downsized, restructured, and formed new coalitions. Investments in new technology and concentration on productivity have been part and parcel with these changes, contributing to improvements in both safety and efficiency. A reason for (and, perhaps a result of) these improvements has been the development of a highly experienced and flexible work force. These changes in mining present an interesting opportunity to modify a few paradigms about work life in general, and perhaps a few paradigms about how we invest in the miner, in particular. Studying these issues now might offer some interesting opportunities for the future, as the foundations for the next generation of mine workers are laid. With the average "experienced" U.S. miner five to fifteen years from retirement, perhaps a key determinant of future success in the world market might be how well we make the transition from today's work force to the work force of tomorrow. We can ill afford to wait a few more years to tap into the special knowledge residing within a veteran mining work force. The WCPM work Crew Performance Model, see pp. ) is one approach to defining, capturing, and transferring this expertise.