Search Documents

By R. W. Baker

"The development of uppers drilling at Brunswick Mining is reviewed. This paper describes design criteria for drilling patterns and the research required for selection of a suitable drill jumbo. The success of the uppers drilling program based on operating procedures is highlighted. IntroductionBrunswick Mining and Smelting Corporation Ltd., operates a 10 500 tonnes per day lead /zinc/copper I silver underground mine some seventeen miles southwest of Bathurst, New Brunswick .The No. 12 orebody, first discovered in 1952 by a group headed by M.J. Boylen, had extensive development, including two shallow shafts (500 ft), and test work carried out on it by St. Joe Lead between 1953-1957. However due to complex metallurgy and depressed metal prices, the operation was suspended.In 1961, a group comprised of M.J . Boylen, K.C . Irving and Patino acquired the rights of St. Joe Lead to the No. 12 property. A concerted development plan was initiated along with construction of the necessary sur face facilities and by July 1964, the property was in production at 4500 tons per day.In 1967 Noranda Mines Ltd. acquired operating control of Brunswick Mining and Smelting Corporation Ltd."

Jan 1, 1988

Sluice box operating practices in Papua New Guinea (PNG), and published work on sluice boxes are briefly reviewed. Some recent work on sediment entrainment mechanisms occurring in sluice boxes have also been described. In the light of this information, some drawbacks in the commonly adopted sluice box operating practices in PNG, and ways of overcoming them, are also highlighted.

Jan 1, 1991

By R. Dahlke, J. A. Finch

"A campaign was undertaken during the greater part of 2001 at Noranda’s Brunswick Mine Concentrator to investigate the role of gas (air) superficial rate distribution (Jg profile) to the cells in the final Zn cleaning stage (bank of seven cells). Three profiles were tested: Balanced (each cell with same Jg), Increasing (from cell 1 to 7), and Decreasing, along with an “as found” profile in a parallel control bank. The experimental design allowed for two confounding factors, changes in ore type and circulating load. The Increasing profile consistently gave the best metallurgy (down-the-bank grade / recovery). The reason for improved performance was traced to the response of the first few cells. The Increasing profile gave the highest selectivity of sphalerite against non-sulphide gangue (NSG) in these cells with relatively even recovery per cell down the bank (10-15% based on feed to each cell). The other profiles gave lower selectivity and higher zinc recovery in the first cells (up to 25% in cell 1), which combined to reduce overall bank performance. The increased selectivity with the Increasing profile is attributed to the low gas rate in the first cells reducing water recovery and hence limiting entrainment of NSG gangue. The Increasing profile was subsequently configured for all four stages in the zinc cleaner circuit.INTRODUCTIONThe performance of a flotation circuit is largely the result of the operator’s response to visual clues. This includes manipulation of the gas (air) input and how it is distributed to cells in a bank. A lack of sensors prescribes this approach. Over the past ten years the Mineral Processing Group at McGill University have developed a set of gas dispersion sensors including one to measure gas superficial rate (or simply “gas rate”), i.e., volumetric gas rate per unit cell crosssectional area, Jg (Gomez and Finch, 2002). The device collects bubbles in a tube immersed in the pulp and infers Jg from the pressure-time curve generated after a valve is closed and air starts to accumulate. The usual units are cm/s. It is robust, reliable and suited for plant use.A version of the Jg sensor was tested extensively during 2000 at Noranda’s Brunswick Mine Concentrator (Dahlke et al., 2001). The results were sufficiently encouraging that a sensor was fabricated to suit local requirements (Insta-Jg). The sensor detected malfunctioning field instruments and flotation mechanisms, and demonstrated that gas distribution to cells in a bank “as found” had no particular pattern, or profile. Preliminary testing suggested that a balanced profile (i.e., all cells with the same gas rate) gave superior metallurgy (grade / recovery down the bank) than the “as found” profile. This observation prompted a focused campaign to explore the impact of the gas rate (Jg) profile, introducing the notion of “gas distribution management”."

Jan 1, 2004

By Carlos F. Perucca

"Potassium is one of the three basic plant nutrients along with nitrogen and phosphorus. There is no substitute for potassium compounds in agriculture; they are essential to maintain and expand food production.Potash is extracted from buried ancient evaporites by underground or solution mining. This accounts for most of the potassium produced. Another important source is brine from landlocked water bodies, such as the Dead Sea, Salar de Atacama or Great Salt Lake.About 95% of potash produced worldwide is used in agriculture. The rest is found in several other industrial uses, including glass manufacturing, soaps, plastics and pharmaceuticals.Currently, three producers: IMC, PCS and Agrium operate 8 conventional and two solution mines in Saskatchewan, five of which run froth flotation circuits, two heavy media-flotation, two run forced crystallization and one natural crystallization.Potash in SaskatchewanPotash was discovered in Saskatchewan in the early 1940’s while drilling for oil. The deposits lie diagonally across the southern plains of Saskatchewan sloping southerly from a 1,000m depth at Saskatoon to more than 1,600 m depth at Belle Plaine and up to 3,000 m in depth in North Dakota. The known deposits are massive, accounting for more than 40% of the world’s known reserves."

Jan 1, 2003

By C. Sawmliana

Deep-hole blasting operations in opencast mines are always associated with some annoyance to the surrounding areas in terms of ground vibration, noise, flyrock, etc. These become more severe when underground mines run parallel to them. Blasting in opencast mines may pose danger to the underground mines in terms of roof/side failures, damage of water dams, isolation/ventilation stoppings and other underground installations. The paper discusses a case study in India on the impact of deep-hole blasting in Ramagundam Opencast Project ? III on the stability of various water dams of GDK-6B Incline coal mine operating in close proximity. The stability of underground water dams of GDK-6B Incline mine was endangered due to deep-hole blasting at OCP-III. There were 15 water dams in seam 3 and 16 dams in seam 4 of the underground mine. The physical strength tests using a Schmidt Hammer instrument were carried out in all the 15 water dams of No. 3 seam and 16 water dams of No. 4 seam. The test revealed that there is a decrease in compressive strength values of three dams of seam 3, namely 6A, 6B and 7. Theose three dams were also directly connected to the water source. Water seepage was also observed from the surfaces of the three dams. However, they were found to be stable in accordance with their design parameters and damage point of view while considering a threshold value of ground vibration as 25 mm/s. It was found that the value of tensile stress generated by a vibration of 25 mm/s was much lower (i.e. 0.171N/mm2) than the tensile strength of the two weakest concrete dams (1.85 N/mm2). Ten experimental blasts were conducted at different working benches of the opencast mine and the ground vibration data were recorded in roof and pillars near various underground water dams. The maximum value of vibration data recorded was 5.9 mm/s in roof near dam no. 1 in seam 3 with the dominant peak frequency of 22 Hz. No adverse effect on either of the dams was observed after that blast. During the period of study, no deterioration/adverse impact was found in any dam of the mine. Based on the results of the study and the analyses of the data, optimized blast design parameters and explosives weight per delay were suggested for the opencast mine to maintain the safety of the underground water dams. Keywords: Opencast blasting, damage, water dams, underground mine, ground vibration

Jan 1, 2009

By Scales PJ, Ralston J

Fine coal particles have been examined with respect to dustiness and its connection with various physical and chemical properties. It appears that a given coal will tend to be dusty ifthe moisture content is low and if the inert maceral content and overall rank are high. The hydrophobicity ofa coking coal (Young-Wallsend) and a steaming coal (Blair Athol) was examined in detail by a dynamic contact angle technique. The YoungWallsend coal had a higher contact angle, on average, than the Blair Athol sample. This result has important implications for dust suppression and associated processes.

Jan 1, 1986

By Christopher Mark

The Bureau of Mines has recently completed a comprehensive study of coal strength. More than 4000 individual test results from over 60 seams were extracted from the literature and combined in the most complete data base of the uniaxial compressive strength of coal ever assembled. In addition, more than 100 case studies of in-mine pillar performance were available in the Analysis of Retreat Mining Pillar Stability (ARMPS) data base. Statistical analysis of this wealth of data has yielded valuable results. The data shows clearly that the "size effect" is related to coal structure. The widely-used Gaddy formula, which predicts a significant strength reduction as the specimen size is increased, was found to apply only to "blocky" coals. For friable coals, the size effect was much less pronounced or even non-existent. Case histories of failed pillars are the best available data on in situ coal strength. This study found no correlation between the ARMPS stability factor of failed pillars and coal specimen strength. Pillar design was much more reliable when a uniform coal strength was used in all case histories.

Jan 1, 1996

By D. K. Ingram, P. Jurovcik

The National Institute for Occupational Safety and Health (NIOSH) identified hearing loss as the most common job-related disease in the United States in its 1996 National Occupational Research Agenda. Previous studies by NIOSH have shown that operators of surface drill rigs without cabs are commonly exposed to A-weighted sound levels exceeding 90 dB. During hammer-drilling, A-weighted sound levels exceeding 100 dB were recorded at the operator station. NIOSH collaborated with a local drilling company to design and install a partial cab between the operator and the drill steel in an effort to reduce the sound level at the operator station. Sound level measurements in the field show the partial cab reduces the A-weighted sound level by 5 to 9 dB at the operator’s left ear and 2 to 5 dB at the operator’s right ear while hammer-drilling. This paper briefly discusses the preliminary design of a cab and the testing of materials for construction of the prototype. An explanation of the ideas behind the prototype design and fabrication are covered. Finally, the field test method and results are discussed in detail.1

By Boorder De, B. S. Panov, A. B. Westerhof, V. A. Korcemagin

Paper presented at the conference on Economic geology in Europe and beyond II, models for <mineral deposits> in sedimentary <basins>, held in Keyworth, UK, 13-14 April 1994. The Hg and Sb deposits of the Mediterranean and Circum-Pacific Belts are often found at elevated structural levels, suggesting that their preferential occurrence in young orogenic belts is not a fundamental metallogenic feature but merely reflects their chances of surviving post-orogenic peneplanation. In western Europe their emplacement appears often to be related to late orogenic extensional events accompanied by a notable increase in heat flow. Although Nikitovka and Almaden have quite different settings, both appear to be related to deep-reaching shears. Together with brittle fault zones at higher levels, these provided pathways for fluid phases that originated at least partially within the mantle. The Nikitovka deposits are located in the Donets segment of the 2 000 km Pripyat-Dniepr-Donets palaeorift in the East European Platform. Initiated in the mid-Devonian with a possible Precambrian precursor, its listric boundary faults displace the Moho from a depth of about 50 km north and south of the rift to 35 km along the axes of the Pripyat and Dniepr segments. The steep central anticline of the Donets segment, within which the main Hg-Sb district is located, is interpreted to be associated with a reactivated fault reaching into the upper mantle. The Almaden syncline, formed during the Variscan Orogeny, may be an older pull-apart basin or half-graben associated with the collapse of the Cadomian Orogenic Belt. It is situated on a major ENE-WSW-striking shear zone which may represent a Late Cadomian transfer zone reaching into the mantle

Apr 1, 1995

By S. G. Malghan, J. P. Van Dillen

Introduction Some uranium minerals are paramagnetic and hence are amenable to concentration by high gradient magnetic separation (HGMS). This paper describes effects of the HGMS parameters-pulp velocity, field strength, matrix loading, and magnetic field gradient-on the product recovery and grade. Unsatisfactory separation of uranium minerals by HGMS is related to ore-specific properties, such as lack of liberation, fine dissemination of uranium minerals, uniform distribution of magnetic minerals throughout the ore matrix, and interference of fine-sized slimes. Experimental techniques to identify and resolve some of these problems are outlined. HGMS of Uranium Ores The mechanism by which uranium minerals are attracted to a magnetic field is either due to its magnetic susceptibility or its association with other minerals that are magnetic. Data on magnetic susceptibility of uranium minerals are scarce. The only reported data are for uraninite at 2360 X 10-6 cm3/mole. Povarennykh (Andres, 1976) concluded that the magnetic properties of minerals depend on: • Structure of the outer electron shell in a mineral with electropositive atoms; • Valence of the atoms; • State of the chemical bonds; • Type of coordination; and • Proportion of magnetic atoms (Fe, Mn, Cr, and Ni) in the composition of the mineral. However, information on the magnetic susceptibilities of the constituent atoms of a mineral alone does not suffice for evaluating the mineral compound as a whole. Most often, uranium minerals can be beneficiated by HGMS if they are associated with other minerals that are magnetic. This appears to be a more predominant mechanism by which the uranium minerals are beneficiated. Experimental A Sala-HGMS (Malghan and Subramanian, 1981), model 10-15-20, separator was used in the experiments. The matrix material-ferromagnetic stainless steel in the form of expanded metal or steel wool-was packed into a 38-mm (1.5-in.) diameter by 360-mm (14-in.) long canister. The matrix material occupied only a 150-mm (6-in.) length. The experimental set-up and slurry flow direction are described elsewhere (lannicelli, 1976). The response of uranium ores in the HGMS was studied by feeding well-dispersed slurry at 10% solids and examining the influence of process variables on selectivity and overall uranium recovery. The chemical and mineralogical characteristics of the ores under study are presented in Table 1.

Jan 12, 1983

By Don Phelps, Dean Brox, Peter Procter, Andy Saltis, Tom Morrison, Jeff Pringle

The Greater Vancouver Water District is currently constructing the Seymour-Capilano Water Filtration Project to enhance the quality of drinking water in the Vancouver metropolitan area. The Seymour-Capilano Water Filtration Project comprises the 1,800 million litres per day Seymour-Capilano Filtration Plant, the 1,080million litres per day Capilano Pumping Station, twin tunnels with associated shafts, and the Capilano Energy Recovery Facility. The twin tunnels will convey raw water under pressure from the Capilano Reservoir to the Seymour Filtration Plant and return treated (filtered) water for distribution. The Twin Tunnels component of the project comprises twin, 3.7 m diameter, 7.2 km TBM bored tunnels, the 180 m deep Seymour Shaft as the main launch shaft, and two 4 m diameter, 268 m deep raise bore exit shafts at Capilano. The Twin Tunnels have been planned as predominantly unlined tunnels sited at depth entirely within granitic bedrock and cross under two major buried glacial valleys of breadths in excess of 1500 metres that are filled with glacial sediments to depths up to 200 metres. The maximum overburden along the tunnel alignment is approximately 400 metres. Comprehensive site investigations and studies were completed during the detailed design stage of the project. The construction of the twin tunnels started in the fall of 2004 and is planned to be completed by mid-2008.

Jan 1, 2005

By L. R. Plitt, A. A. Turak, B. C. Flintoff

"Since the publication of empirical cyclone models by Lynch and Rao in 1975 and by Plitt in 1976, the technical literature on this subject has consisted primarily of reports of applications, with only a few articles discussing basic modifications or enhancements in model form. In fact, most of the modelling eff ort in this period has been concerned with theoretical models based on the hydrodynamics of multiphase flow. (Preliminary resutls have been encouraging, however, it will be some time before this approach reaches the practical application stage.) This paper presents a review of empirical cyclone modelling technology, with an emphasis on developments since the mid 1970s. The topics addressed include homogeneous and heterogeneous ores, parameter estimation techniques, parameter confidence intervals, and the introduction of a new conceptual model of cyclone operation.IntroductionSince their first reported application in the mineral industry by Driessen (1939), cyclones have become a common unit operation in all of the process industries. The widespread use of the cyclone stems from its relative low cost and its versatility. It can be employed to carry out liquid-liquid, solid-liquid and solid-solid separations. It is the area of solid-solid separation which is of greatest interest to a mineral processing engineer. Historically, this area was divided into two application categories: (I) Separation according to density, the cyclone washer, and, (2) Classification according to particle size, the cyclone ciassifier. (When water is the carrier fluid, the cyclone is more often called the hydrocyclone. For the purposes of this paper the two names are used interchangeably). Classification is the principal application in mineral processing circuit s. Within this category, the cyclone is most commonly employed to provide some positive control over the size distribution of product from a grinding circuit. Other uses include sand-slime separation prior to froth flotation and mill tailings treatment, either for dam construction or in backfill preparation."

Jan 1, 1987

By D. R. Hack, N. M. Sirakov, M. L. Feves, M. Iwanowski

This paper presents a new approach capable of volume calculation of 3D reconstructed geological objects. The method is based on a well-known concept that states the volume of an object can be computed as the limit of the sum of the area of infinite number of sections, which cut the 3Dobject. Since shortage of input data about the geological objects usually exists, Mathematical Morphology and polynomial interpolation are employed to generate a set of intermediate sections between the set of initial sections. A Mathematical Morphology tool is applied to compute the area of the two of sets initial and generated 2D sections. Regularities together with Delaunay Triangulation are employed to perform 3D reconstruction. A formula is developed on purpose of volume calculation of the reconstructed objects. A set of ten theoretical, electrical resistivity cross-sections were generated and used to perform an experiment to show the capability of our approach to estimate the volume of complex 3D geological object in case of sparse 2D sections. The volume determined using the morphological approach presented in this paper show good correlation with the volume of the original input object. Advantages and disadvantages of our volume calculation approach are discussed in the conclusion of this paper. Keywords: electrical resistivity, sparse 2D sections, geological objects, smooth 3D visualization and volume calculation.

Jan 1, 2003

By Yousef Ghorbani, Jafar Abdolahi Sharif, Fatemeh Kazemi, Ataallah Bahrami

Kinetic models are the most important tool for predicting and evaluating the performance of flotation circuits. Gilsonite is a natural fossil resource similar to an oil asphalt, high in asphaltenes. Here, in order to determine the kinetic order and flotation rate of a gilsonite sample, flotation experiments were carried out in both rougher and cleaner stages. Experiments were conducted using the combinations of oil–MIBC and gas oil–pine oil, with one test without collector and frother. Five kinetic models were applied to the data obtained from the flotation tests using MATLAB software. Statistical analysis showed that the results of the experiment with oil–MIBC were highly in compliance with all models. Kinetic constants (k) were calculated as 0.1548 (s−1 ) and 0.0450 (s−1 ) for rougher and cleaner stages, respectively. Rougher and cleaner tests without collector and frother also matched all models well (R2 > 0.98), with k values of 0.2163 (s−1 ) and 0.284 (s−1 ), respectively. The relationship between flotation rate constant, maximum combustible recovery, and particle size showed that the maximum flotation combustible recovery and flotation rate were obtained in the size range of −250 + 106 μm in the rougher and cleaner stages. The combustible recovery and flotation rate were higher in the rougher flotation process than in the cleaner stage.

By Yousef Ghorbani, Jafar Abdolahi Sharif, Fatemeh Kazemi, Ataallah Bahrami

Kinetic models are the most important tool for predicting and evaluating the performance of flotation circuits. Gilsonite is a natural fossil resource similar to an oil asphalt, high in asphaltenes. Here, in order to determine the kinetic order and flotation rate of a gilsonite sample, flotation experiments were carried out in both rougher and cleaner stages. Experiments were conducted using the combinations of oil–MIBC and gas oil–pine oil, with one test without collector and frother. Five kinetic models were applied to the data obtained from the flotation tests using MATLAB software. Statistical analysis showed that the results of the experiment with oil–MIBC were highly in compliance with all models. Kinetic constants (k) were calculated as 0.1548 (s−1 ) and 0.0450 (s−1 ) for rougher and cleaner stages, respectively. Rougher and cleaner tests without collector and frother also matched all models well (R2 > 0.98), with k values of 0.2163 (s−1 ) and 0.284 (s−1 ), respectively. The relationship between flotation rate constant, maximum combustible recovery, and particle size showed that the maximum flotation combustible recovery and flotation rate were obtained in the size range of −250 + 106 μm in the rougher and cleaner stages. The combustible recovery and flotation rate were higher in the rougher flotation process than in the cleaner stage.

Paper written on project work carried out in partial fulfilment of M.Sc. (Chemical Engineering)degree Identification of non-linear systems can be a daunting task and in the process industries the problem is complicated considerably by the presence of noise from various sources, non-stationarity of the data and intermittence, such as observed in particulate flows. Traditional methods, such as frequency analysis and linear model-ling do not handle these systems well. Similar problems arise with the application of non-linear theory developed over the last few decades, where much of the analysis depends on embedding of the data in a phase space or pseudophase space, since these methods were not originally designed to deal with noisy systems. In contrast, singular spectrum analysis is a method which can be used to identify structure and distinguish noise from important information in multivariate data, such as the trajectory matrices of time series measurements. It provides an orthogonal basis onto which the data can be transformed, so that components of the time series can be investigated individually. With Monte Carlo methods, the components can be compared with those from linear surrogate data in order to identify possibly non-linearities in the data. In this paper, this versatile technique is briefly explained and illustrated by means of case studies.

Jan 1, 2003

By R. L. Virta

Editor?s note: Each year, the June issue of Mining Engineering features an industrial minerals review. Several people put in a fair amount of time in developing the material for this issue. Thank you to the industrial minerals annual review editor, to the technical committees chair and vice-chair, and to the authors of the individual commodity profiles. Jim Norman, member SME, of GeoTrans Inc., is the industrial minerals annual review editor. Abani Samal, member SME, of Pincock Allen & Holt, is chair of the industrial minerals technical committees. Technical committee vice chairs include: ? Abani Samal, member SME, of Pincock Allen & Holt, agricultural minerals. ? Aaron McMahon member SME, of Pincock Allen & Holt, ceramics and refractories ? Bradley S. Van Gosen, member SME, of the U.S. Geological Survey, chemical raw materials. ? Mark Zdunczyk, member SME, of Continental Placer Inc., construction materials. ? Jerry Gauntt, member SME, of Marston, fillers and pigments. ? Michael Cheshire, member SME, of Indiana University, sorbents, filters and process aids. ? Candace Trimble, Oil-Dri Corp. of America, specialty minerals. Their help makes possible this June industrial miner-als issue. On behalf of ME readers, the editors thank them. Ball Clay Four companies ? H.C. Spinks Clay (owned by Lhoist Group), Kentucky-Tennessee Clay (owned by Imerys Group), Old Hickory Clay, and Unimin Corp. ? mined ball clay in four states in 2008. Production, on the basis of preliminary data, was 964 kt (1.1 millon st) with an estimated value of $45.3 million. That was a 10- percent decrease in tonnage from 1.07 Mt (1.2 mil-lion st) with a value of $49.2 million that was produced in 2007. Tennessee was the leading producer state with 63 percent of domestic production, followed by Texas, Mississippi and Kentucky. About 73 percent of production was airfloat, 16 percent was crude and 11 percent was water-slurried.

Jan 1, 2009

By M. I. F. S. Cruz, R. Pedersen, F. J. A. S. Barriga, A. Dias, A. F. A. Marques

"Underwater hydrothermal vents are known since the 1970s and their importance for the global economy is growing as new discoveries and new assessments are made each year (Cherkashov et al., 2010; Corliss et al., 1979). The similarities of seafloor massive sulfides, representing the younger versions of the well exploited on land volcanogenic massive sulfides, bring an increased awareness to the potential of the sea (Ajan G. Galley, 2007; Hannington et al., 2011; Herzig and Hannington, 1995). The Arctic Ocean presents itself as an opportunity to study new interest areas and numerous hydrothermal systems (active and inactive) were discovered along the Arctic Mid Ocean Ridge (AMOR) (Pedersen et al., 2010b). The Mohns ridge is an ultraslow spreading ridge of the AMOR (Vogt, 1986) where two hydrothermal vent sites were recently discovered, the Jan Mayen and the Loki’s Castle (Pedersen et al., 2010a; Pedersen et al., 2009; Pedersen, 2005). Here we compare these two Arctic hydrothermal systems, which represent two well-differentiated end-members of hydrothermal fields in the region."

Sep 1, 2014

By A. v. E. Conradie, I. Nieuwoudt

Comminution and flotation circuits are frequently perturbed by disturbances, such as feed particle size variations, ore hardness and varying mineral liberation, which can have a significant impact on the recoveries and grades. Although advanced control strategies can neutralize many of these disturbances, few such systems have been implemented at present. One reason is that it is only recently that the requisite sensor systems have been developed and used to control froth flotation systems. Another is owed to the complexity of these non-linear interactive systems. In this paper, a plant-wide control strategy is considered, wherein both unit operations have a single overall control objective. The automated design of the controller is based on an advanced evolutionary algorithm viz., Symbiotic, Memetic Neuro-Evolution (SMNE), for developing neural network controllers in a reinforcement learning framework. A rigorous phenomenological comminution and flotation model was used to develop suitable neurocontrollers, which used all possible sensor inputs and available manipulated variables. The neurocontroller managed to identify optimal or near-optimal operating conditions consistently and showed robust performance in the presence of significant disturbances. The results suggest that evolutionary reinforcement learning offers a very competitive approach towards the development of integrated non-linear controllers for mineral processing plants. Keywords: neural networks, control, flotation, comminution, evolutionary reinforcement learning

Jan 1, 2003

By R. L. J. Phillips

"The environmental impact of the Rabbit Lake project is presented. Baseline data for fish, water, air and radon collected in 1973, 1975, 1980and 1986, are compared with post-development environmental monitoring data. Predicted environmental impacts for the developed Rabbit Lake and B-zone deposits are compared to the actual impacts. INTRODUCTIONThe environmental impact of the Rabbit Lake project has been documented through the years in several submissions to the government agencies. In 1972, the environmental baseline study for the Rabbit Lake area was completed prior to any mining activity at the Rabbit Lake pit (Fig. 1).Sampling concentrated on Hidden Bay and Pow Bay, which received the treated effluent and the waters drained from Rabbit Lake respectively.A second baseline study was done on the Collins Bay area in 1980(Fig. I) in preparation for the mining of the B-zone pit. The detail in this study was considerably greater than the detail in the previous study. Collins Bay and Harrison Peninsula were the areas sampled. The B-zone deposit is being mined at present.With the discovery of the A-zone, D-zone and Eagle Point deposits, it was decided in 1986 to begin proceedings to obtain approval from Saskatchewan&apos;s Department of the Environment, and from the Atomic Energy Control Board to develop these deposits.In preparation, a third baseline study of both the Rabbit Lake and Collins Bay areas was done in 1986 and 1987. The emphasis was to establish the baseline at the three new deposits, to quantify the actual impacts of the existing Rabbit Lake operations and to confirm the Collins Bay B-zone (1980) impact predictions. The new deposits will allow us to continue to produce uranium into the future. In January 1988, Saskatchewan approval was received.Since 1975 in the Rabbit Lake area and 1980 in the Collins Bay area, routine environmental monitoring has been done. This has resulted in one of the largest and most comprehensive environmental data bases in North America in mining. By the time the Eagle Point deposit is mined to completion, there will have been data collected for approximately 40 years.Further discussions follow which describe the impacts of the past (1972 to 1984), the present (1985 to 1987) and the future. In addition, the past and present performances and the future plans of the .waste management systems will be discussed."

Jan 1, 1989