Search Documents

By D. J. Kunz

Myanmar Ivanhoe Copper Company Ltd. (MICCL) has been operating the Sabetaung- Kyisintaung (S&K) Project producing LME Grade A Copper Cathode using the Heap Leach-SX-EW Process since 1998. The mineralization is mainly Chalcocite and the mine has a life of 20 years at the designed annual production of 25,000 tonnes of cathode copper. Design capacity was achieved within two of months of start-up. The mine is among the world’s lowest cost, Heap Leach-SX-EW operations. Information regarding plant design and operation are presented along with the challenges lying ahead and the latest developments. Daniel Kunz is President and Chief Operating Officer of Ivanhoe Mines, and a director of MICCL. He has more than 20 years’ experience in mining, construction and engineering. Prior to joining Ivanhoe Mines in 1996, Mr. Kunz was Vice President and Controller of Morrison Knudsen Corporation, a major international mining and construction company. He was also President and Chief Executive Officer of MK Gold Company, a public mining company listed on NASDAQ.

Jan 1, 2001

By Mike Sapiro

"Heath Steele Mines is a base metal producer situated near Newcastle, N.B. presently treating 3500 TPD of complex Cu-Pb-Zn ore. The ore consists of massive fine grained sulfides averaging I. 1% Cu, 1.6% Pb and 4.5% Zn.The original mill started in 1956 at 750 TPD and was successively expanded through 1500 to 3000 TPD in 1969. In 1972 an expansion to 4000 TPD was initiated. It was planned to obtain the maximum benefit from equipment and manpower by adding some process equipment, instrumentation, an on stream analyser, and a process control system. The benefits from this approach could be greater than normally expected, because of the complex metallurgy of this ore.IntroductionThe crushing plant is of conventional design with two 5 ½ ft, Symons cone crushers with the crushed ore screened to -7/8 inch on a 61 x 16 1 Al I is Chalmers vibrating screen and stored in four 1000 Ion bins. There are two para I lei grinding circuits, each one consisting of the following: one Rod Mill in open circuit, one Ball Mill in closed circuit with two 20"" Krebs cyclones, and one Ball Mill in closed circuit with three 15"" Krebs cyclones, Al I the Mills are 9' x 121 Al I is Chalmers Mills. The secondary cyclone overflow from each grinding circuit is thickened and combined to form flotation feed. The final product is 65% - 400 Mesh. Two regrind mills have been installed as part of the expansion."

Jan 1, 1977

By S Henderson, J V. Lawless

The worldwide association of low-sulfidation epithermal gold mineralisation, bimodal rhyolitic-basaltic volcanism and rifting is confirmed in New Zealand. In the currently productive Coromandel epithermal-gold province reported Ar-Ar dating of adularia from low sulfidation deposits falls into two groups at 6 and 7 Ma. Bimodal rhyolitic-basaltic volcanism has been reported to be K-Ar dated at 9 to 7 Ma and 6 to 5.5 Ma. Epithermal gold mineralisation in Northland is spatially associated with bimodal basaltic-rhyolitic volcanism, with rifting cogenetic with that in the CVZ. The Taupo Volcanic zone (TVZ) is sufficiently young that the presence of a segmented rift with recent bimodal rhyolitic-basaltic volcanism can be genetically associated with epithermal gold mineralisation, which occurs as both fossil occurrences and in active geothermal fields. This reinforces the known potential prospectiveness of the Coromandel area and increases that of Northland and the Taupo Volcanic Zone.

Jan 1, 2005

By Edward Judd

CANADA'S mining industry is rapidly recovering from the depression through which it passed in 1921. Its total output of $183,029,600 in 1922 was 6.4 per cent. greater than that of 1921, and was exceeded by only three previous years, 1917, 1918, and 1920. Table 1 compares the output of a few of 'the more important items selected from preliminary data published' by the Dominion Bureau of Statistics. TABLE 1.-OUTPUT OF CERTAIN MINERAL PRODUCTS IN CANADA PER CENT. 1921 1922 CHANGE Cobalt, metal and in compounds, lb 252,000 443,800 +76.1; Copper contents of blister, matte, and exported ores, lb 47,620,820 43,321,400 - 9.0 Refined copper, lb 4,286,000 730,000 -83.0 Gold, fine oz 926,329 1,230,985 +32.8 Pig iron, sh. tons 665,676 429,024 -35.5 Lead, sh. tons 33,340 47,085 +41.2 Nickel contents of matte, etc., lb. 19,293,060 17,496,490 - 9.3 Silver, including that in base bullion, gold bullion, etc., fine, oz. 13,543,198 17,611,646 +30.0 Zinc (nearly all refined), sh. tons. 26,545 28,199 + 6.2 Asbestos shipments, sh. tons 92,761 136,657 +47.3 Coal, all grades, sh. tons 15,057,500 15,045,300 Gypsum shipments, sh. tons 386,550 441,160 +14.1 Natural gas, M. cu. ft 14,077,600 14,954,100 + 6.2 Petroleum, bbl : 187,540 178,570 - 4.8 Cement, bbl 5,752,885 6,943,968 +21.0 Brick, structural, all kinds, M. , , 109,009 127,137 +17.0 On the basis of estimated market values, the whole output of 1922 was contributed as follows: Metals, 33.4 per cent.; non-metallic minerals, 45.1 per cent.; structural materials and clay products, 21.5 percent.; this distribution indicates a return of the metal mining. industry nearly to the position of relative importance that it occupied. before 1921, in which year metals contributed only 28.7 per cent. to the total value. of output while non-metallics gave 51.1 per cent. Canadian cobalt originates entirely in the ores of the Cobalt district, which are mainly treated at smelters in southern Ontario, although some quantities of residues have been exported to England and Europe. Exports during 1922 increased even more than production, consisting of about four-fifths . cobalt oxides and salts, and one-fifth of cobalt alloys and other metal combinations.

Jan 8, 1923

By Clifford B. Farris

The natural cementation strength of retorted oil shale is the focus of this investigation. The optimum retorting temperature and residence time to obtain natural cementation strength in retorted Green River oil shale from western Colorado were determined as follows: [Optimum Conditions for Natural Cementation Maximum Residence Obtained Retorting Time at Compressive Mode of Temperature Temperature Strength' Retorting °F °C hr psikg/cm-2 Direct 1,520 822 2.0 270 19.0 Indirect 1,530 832 2.9 325 22.8] 1 Scattered samples were tested at strengths as high as 463 psi (32.6 k /cm 2) (Run 8, indirect mode) and 406 psi (28.5 kg/cm2) (Run 48, direct mode), but these high strengths were not confirmed by nearby tests. Minus 0.5-inch (1.3-cm) Green River oil shale was heated in a differential retort under conditions simulating potential full-scale retorting processes. The variables investigated were retorting temperature, residence time, retorting mode, and shale grade. Samples of the retorted Green River oil shale were moistened to optimum plus 2% (25%) moisture, compacted to 95% Proctor density, sealed and cured at 100°F (38° C) for up to 40 days. Lower curing temperatures, which are likely in the field, would probably result in significantly slower development of cementation strength, and might lower the ultimate strength developed. However, these effects were not studied in this project. The cured samples were tested for compressive strength, and correlative equations were developed for the increase of compressive strength with curing time as a function of retorting temperatures and residence time. Petrographic analysis indicated that the cementing mechanisms may be the interlocking growth of acicular hydrated calcium aluminum sulfate crystals between the contacts of retorted shale fragments. Samples of the retorted shale were also tested for optimum Proctor density and moisture. Permeability and quality of the leachate of shale from typical runs were determined. The effect of use of retort rather than tap water on compressive strength and leachate after curing was determined. The retorted shale effectively filtered several mineral constituents from the retort water.

Jan 1, 1979

By A. Jennings

[ ] In November 2005, Essroc Cement, part of the Italcementi Group, commissioned a long overland conveyor at their Nazareth plant in Pennsylvania. This conveyor, tagged CV-105, was designed to transport 1000 tph of limestone from the quarry to the kiln, and 400 tph of hot clinker (at 300°F) at back from the kiln to a handling facility about halfway back. Conveyor CV-105 is 8969 ft (2733 m) long. It gains 152 ft (46 m) of elevation in the first 1570 ft (480 m), then is mostly flat for the remaining 7400 ft (2250 m) (Figure 1). After the limestone is discharged at the head pulley, hot clinker is loaded onto the return side of the belt. This clinker can be discharged at one of two locations.

Jan 1, 2012

By Marc D. Melker, Geoffrey R. Lane, Michael Jahraus

"The Cresson gold deposit is located in the Cripple Creek district of Colorado. The deposit is composed of volcanic intrusive rocks and volcanogenic sediments where gold mineralization is associated with veins and cavities within a diatremal breccia.The purpose of the current study was to:1. Determine the penetration potential of the Cripple Creek Breccia.2. Assess the relationship between penetration and gold recovery within the Breccia.Two methods were applied using a cyanide solution containing ultraviolet sensitive dye to elucidate pathways of penetration within the rock. The first involved stagnant soaking of twoinch square pieces within the solution. The second method involved column leaching of ~100kg of Breccia crushed to P80 12.7 mm (0.5 inch). Samples were selected at specified intervals to capture the penetration progress of the solution. Photomicrographs and image analysis were utilized to illustrate and quantify the degree of penetration.Results indicated that the maximum penetration for the Cripple Creek Breccia (85 to 97%) due to a porous and permeable groundmass, containing large non-porous lapilli fragments. In addition, ~90% of leachable gold was recovered with only ~50% rock penetration.INTRODUCTIONDye penetration studies were first developed at SGS-Lakefield Research for the purpose of determining the fluid penetration amenability of differing rock types. The method was to place a large rock or drill core in a pan with 1 to 2 inches of a pre-mixed, water based fluorescent dye. The sample was sequentially cut after prescribed time periods to reveal a fresh surface. The cut surface was photographed under long wave ultraviolet light, and the same piece returned to the dye and allowed to sit until the next prescribed cutting."

Jan 1, 2006

Safety rules for installing and using electrical equipment in and about coal mines covered in this information circular supersede those previously included in Bureau of Mines Bulletin 514, issued in 1952. This revision brings these rules up to date and more nearly in line with present operating and safety practices in the industry. The rules are intended to supplement existing Federal and State regulations, and no provision shall be construed to oppose or supersede any provisions of the Federal Mine Safety Codes, the Federal Coal Mine Safety Act, or the mining laws of any State. The rules were designed to permit progress, such as application of new or improved materials and equipment or use of new practices where these materials, equipment, or practices retain or improve the level of safety established by these requirements. It is hoped that they will fill the need for a concise edition for mine electricians and electrical engineers, especially those who do not have ready access to more detailed rules or codes.

Jan 1, 1964

By R. Karl Zipf, Francois E. Heuze

Stress analysis programs such as MULSIM/NL, LAMODEL, MinSim 2000, and EXAMINETAB are used in the mining industry to analyze stresses and displacements in coal mines, platinum mines, gold reefs, and tabular-type deposits. These relatively simple numerical models can efficiently simulate yielding and failure of a rock mass near a mine opening and subsequent stress transfer. The main input parameters for these models are a family of nonlinear stress-strain curves for the in-seam material. For many applications of these models, such as in coal mining, extensive field measurements and observations exist from which to estimate these stress-strain curves and calibrate the numerical models; however, such measurements are lacking for other types of mines. A three-step method is presented to determine nonlinear stress-strain curves for boundary-element (BE) programs used in many mining applications. The method requires a suite of laboratory-scale strength tests at various confining pressures. Note that this analysis uses laboratory-measured strength and modulus properties of alluvium. The dependency of the mechanical properties of alluvium on scale has not been established, although more tests are being planned. However, it is believed that the relative comparisons performed are valuable regardless of scale effects. First, the FLAC2D computer program is used to model the laboratory tests and determine cohesion (c) and friction angle () for a Mohr-Coulomb material model. Second, another FLAC2D model uses the c and values to calculate vertical stress and strain around a single opening in the rock mass. This model calculates the stress-strain path of points at various distances from the opening boundary. Finally, based on these stress-strain paths, the stress-strain curves needed for a BE analysis are derived. This three-step method was demonstrated in a large, flat-lying underground test facility in very weak rock. The BE analyses agreed well with observations of failure at the test facility and provided a basis for evaluating the behavior of alternative layouts.

By A. Kondratiev

A structurally-based viscosity model for fully liquid silicate slags has been developed and applied to the Al2O3-CaO-‘FeO’-SiO2system at metallic iron saturation. The model links the slag viscosity to the internal structure of melts through second nearest neighbour bonds concentrations taken from the quasi-chemical thermodynamic model. This viscosity model describes experimental data over the whole temperature and composition ranges within the Al2O3-CaO-‘FeO’-SiO2system at metallic iron saturation and can now be applied to other industrial slag systems.

Jan 1, 2004

Safety rules for installing and using electrical equipment in and about coal mines covered in this information circular supersede those previously included in Bureau of Mines Bulletin 514, issued in 1952. This revision brings these rules up to data and more nearly in line with present operating and safety practices in the industry. The, rules are intended to supplement existing existing Federal and State regulations, and no provision shall be construed to oppose or supersede any provisions of the Federal Mine Safety Codes, the Federal Coal Mine Safety Act, or the mining laws of any State. The rules were designed to permit progress, such as application of new or improved materials and equipment or use of new practices where these materials, equipment or practices retain or improve the level of safety established by these requirements. It is hoped that they will fill the need for a concise edition for mine electricians and electrical engineers, especially those who do not have ready access to more detailed rules or codes.

Jan 1, 1964

By M. Götze, P. Eysel

Over the last years, the importance of the assessment of environmental and social aspects as well as of issues of good governance has increased significantly in mining finance. For this, international standards as well as internal guidelines of the banks and other involved institutions have been established and continuously improved. Considering these standards and regulations, the banks can influence the sustainability of mining projects - and they have done so in the past -, mainly by implementing certain provisions and covenants in the loan documentation, binding the financing to the mining company’s adherence to the agreed sustainability standards. However, there are limits to the banks’ influence due to the competitive environment with other available means of financing. Nevertheless, the experience of the last years has shown that the standards and regulations bound to the financing by the banks help to lead the mining industry towards more sustainable projects.

Jan 1, 2011

By W Barry Gregg

The rock blasting and mining industries use a system of detonators and explosives for mining operations. Many detonators use small metal bridgewires, which are heated by passing a current through the wire, heating and igniting the pyrotechnic powder in contact with the wire, Typical bridgewires require a current of at least 3 amps, applied for a few milliseconds, for an explosive output. The semiconductor bridge (SCB), in comparison, initiates an explosive in 0.01 to 0.1 of a millisecond.

Jan 1, 1992

By H. A. Schnell

"The Phase I Mill at Cluff Lake in northern Saskatchewan was designed to accommodate a very specific high grade uranium ore. As this high grade ore was depleted, construction was undertaken on a new mill circuit (Phase 2) to process a more conventional lower grade ore deposit.The Phase 2 Mill expanded the ore throughput to 800 tonnes per day. The new process employs crushing, grinding, leaching, counter—current decantation, solvent extraction and magnesia yellowcake precipitation and drying to produce a yellowcake concentrate.This paper discusses the process decisions required for this expansion and outlines the new mill circuit. Included is a review of the start up in August, 1984.1.,INTRODUCTION The Cluff Lake Uranium deposit is located 720 kilometers north of Saskatoon in northern Saskatchewan. A high grade deposit was discovered in 1970 with the first production taking place in 1980 after lengthy hearings. The original mill (or Phase 1 Mill) was specifically designed to accommodate this very high grade ore for a very limited plant life.Pilot plant work was carried out in 1981 on the other lower grade ores found in the immediate Cluff Lake area. Feasibility and process selection studies were then undertaken as the Phase 1 mill was nearing its end of life. These studies were completed in March 1983 when approval was given to construct the new Phase 2 mill."

Jan 1, 1985

By John T. Metcalf

The assembly procedures for nine different wire rope terminations used in the mining industry are presented in a format and manner to facilitate training and to provide points where inspection of the termination should be performed. The nine terminations addressed are: Flemish Loop with Steel Sleeve & Thimble, Flemish Loop with Steel Sleeve, Wedge Socket, Swaged Socket, Turn Back Loop with Sleeve & Thimble, Thimble Splice with Four Tucks, U-Bolt Clip & Thimble, Zinc Poured Socket, and Epoxy Resin Poured Socket. The manual was prepared to be used primarily for field type mining operations or training where high capacity machinery is quite limited. It is nut the intent of this manual to suggest that the procedures presented are those to be used by manufacturers or other commercial enterprizes. A different set of procedures may be more appropriate where ideal space and equipment resources are available. The assembly procedures were derived from standard industrial practice, manufacturer's recommendations, and the open literature on the subject. These same procedures were used to prapare test specimens for an extensive series of pull and axial fatigue tests. The results of these tests indicate that these procedures are satisfactory in all respects. This manual is to be used as part of a complete training program. Although a brief glossary is included, there has been no attempt to make this a primer on wire rope. The selection of wire rope termination hardware, like the selection of the wire rope, is a subject not covered by this manual. The reader is cautioned that there are various sources for such hardware and this selection must be done carefully.

Jan 1, 1978

By Edmund S. Leaver, R. S. Dean, T. L. Joseph

The metallurgy of manganese has developed along the lines of iron metal¬ lurgy. Enough high-grade ore has Been available so that by reduction with carbon it could be turned into an iron-ma.nga.nese alloy and a slag containing some 9 to 15 percent manganese. More siliceous ores have been smelted in the blast furnace to form iron-silicon-manganese alloys called spiegel. When lower-grade ores came in for serious consideration, which lias only been since l°l4, two types of processes received the most consideration — hydrometallurgical processes to produce a concentrate which could be smelted like the higher-grade ore and processes involving concentration of the manga¬ nese from manganiferous iron ores by preferential reduction of the iron (184)1. Special chapters in this bulletin are devoted to the production of ferro¬ manganese from ore, the hydrometallurgy cf manganese, and the Bureau of Mines modification of the preferential reduction process. Other methods of producing manganese alloys from low-grade or refractory ores have been suggested and may find future application. Manganese has a very high affinity for sulphur and is particularly adaptable to concentration by matte smelting. According to Betts (26), manganese silicate may be smelted with pyrite to give manganese sulphide and iron silicate. This method would be applicable to concentration of either the silicate or carbonate ores. The sulphide, once obtained, could be roasted to oxide and reduced in the usual way. Another possibility for the production of manganese from silicate ores involves their reduction by silicon or manganese silicides. Swedish Patent 52290, February 25, 1925. covers the reduction of a slag rich in manganese by silicon-manganese alloy containing more than 10 percent silicon, Joseph H. Brennan (38.) describes the concentration of manganese iron ores by partial reduction with silicon. Beckett (7,4,19) describes the reduction of manganese dioxide with a manganese silicide for the production of standard ferromanganese. Beckett gives as a typical alloy, manganese 64.4, silicon 24.6, and as a typi¬ cal ore, 5S.5O manganese as MnO^. The product of the reaction between these two is 80.11 percent manganese and 1.22 percent silicon.

May 1, 1934

By Steve Kral

It seems that mining has been in the doldrums for awhile. Except for gold, metals prices remain depressed. And economic conditions in the United States and around the globe have put governments in a financial bind. This affects new building and infra-structure repairs, which, in turn, have a major impact the building materials industry. Add to that the severe environmental and regulatory restrictions placed on the mining industry in developing new mines and expanding existing ones. It’s enough to make a mining engineer/geologist/metallurgist go sell real estate. So why do those employed in the mining industry stay in the business and remain optimistic? Many of them will say that they have been through down cycles before and know that an upswing is in the offing. They also know that society will always need the commodities they produce. And they love the challenge. The challenge in mining’s case is producing commodities as cheaply as possible, in an environmentally sound manner and improving the quality of life in the communities where they work.

Jan 1, 2003

By Thomas Lane Carter

THE history of mining in South Africa differs somewhat from that of other countries in the part taken by the aborigines in the development ?of the mineral deposits. The Spaniards in America, and the fortune-seekers of Australia and New Zealand, found large numbers of natives in these new countries, but the inhabitants did not become willing or efficient workers ill the mines which the white men started. The Kaffirs of South. Africa have not shown the same antipathy to labor, nor do they show any signs of dying out in the presence of the white man's civilization. They are a virile race, and so far the vices of civilization have not killed. them. While it is true that the brain and skill necessary for the exploitation of the mineral resources of this sub-continent-have been supplied by the white race, it is also a fact that most of the rough labor in the development of the mining industry of South Africa has been done by the Kaffirs. The Kaffir tribes differ greatly in their mental and physical capabilities. Compare, for instance, a Zulu of Natal with a Bechuana, or a Xosa of Cape Colony with some of the degenerate tribes of Central or East Africa, and you will find that they have little in common, save that their skin is black and that they do not believe in clothes. As a general rule, the tribe's in the milder, healthier climates are far superior, both in mind and body, to the Kaffirs brought up in the hot malarial sections of Central Africa; and it naturally follows that the black men from the temperate zones of the country, are much finer workmen than the degenerates from less favorable sections: It is universal in South Africa to speak. of the .Kaffirs as " boys." No matter if he is 90 years old, the Kaffir is always a " boy," and in this paper the word " boy " is synonymous with Kaffir.

Nov 1, 1908

By M. Somerville, S. Sun

The liquidus temperature and viscosity of a range of melter slags produced in South Africa were determined. Drop-quench experiments were carried out on the supplied plant samples to determine the liquidus temperature and phase relations at sub-liquidus temperatures. The temperature measurement range covered 1300°C to 1630°C. Results from these experiments show liquidus temperatures for the melter slags to be in excess of 1500ºC with the chromium containing spinel as the primary crystalline phase. At lower temperatures, an olivine or pyroxene phase co-existed with the spinel phase. The viscosity of the slags was determined over a temperature range of 1350 to 1550°C, under a controlled atmosphere. Results show two orders of magnitude variation in the viscosity (0.2 to 20Pa s) with strong effects of slag chemistry and temperature. Slags with lower SiO2and Cr2O3concentrations were more fluid. Slags with the lowest FeOx and highest SiO2concentrations were the most viscous. These observations are in accord with general behaviour of silicate slags. While the presence of a spinel phase may have an effect on the viscosity of the melter slags, results obtained to date indicate a much stronger effect due to the presence of an olivine or pyroxene phase at lower temperatures. Keywords: phase equilibria, liquidus, viscosity, slags, olivine, spinel, pyroxene

Jan 1, 2004

By F. Peer

In most coal preparation processes, water is a necessary medium, but the presence of water in coal after it has been cleaned has a negative impact on transportation costs, handling and specific energy values. The utilization of super absorbent polymers (SAP) in the nappy application is well known. The concept of utilizing these polymers was investigated for the purposes of dewatering coal and other fines, generated by preparation processes such as flotation. SAPs are granular highly cross-linked synthetic copolymers with excellent water-absorbing properties. The dewatering process is characterized by three main stages: (a) contact of super absorbent polymer with high-moisture fine coal; (b) separation of dewatered fine coal from super absorbent polymer; and (c) regeneration of used super absorbent polymer, by exploiting its response to changes in conditions such as pH or temperature. Preliminary tests showed the separation step to be very difficult. The novel idea of encasing a given amount of polymer in a water permeable cloth solved this problem (of separating the swollen polymer from the dewatered coal). Preliminary tests investigating the effectiveness of the sachets of polymer showed a drastic decrease in the moisture contents of slurries. Furthermore, it was shown that it was possible to regenerate the polymer (still within the sachets) through thermal drying. A full-scale experimental programme was then followed to accurately determine the feasibility of using sachets of SAP. The experimental variables were initial slurry moisture content and polymer dosage. It was observed that the sachets seemed to work fastest and most effectively at high moistures and also at higher dosages of SAP. Regeneration of the polymer was also investigated, using two methods: thermal regeneration and pH-induced regeneration. The experimental variables, for investigating the regeneration process, were method of regeneration and grade of water used. Thermal regeneration at 70°C seemed to work successfully. Although the cost of using thermal energy is still a problem, the safety aspect (fire hazards) has been addressed since the polymer does not ignite when heated, unlike fine coal particles that may do so. The alternative method of regeneration, which exploits the pH-sensitivity of the polymer, was less successful, and further work needs to be conducted.

Jan 1, 2003