Search Documents

By J. Wennerstrand

Slender steel piles have found an increased use in Sweden in resent years. These piles are often driven throw soft normally consolidated clay to refusal in till or at the rock surface. In contrast to most other piles the bearing capacity with regard to failure of the shaft is in many cases smaller than the bearing capacity with regard to failure of the soil or rock at the lower end of the pile. Imperfections such as deviations from a straight line of the pile centerline and residual stresses in rolled and welded profiles are important for the capacity of the pile shaft. Even thow the second order moment caused by initial deviations in piles is only half of that in a column with the same slenderness, imperfections can and should be accounted for in much the same way as for columns.

Jan 1, 1989

By M. A. Steinberg, J. Wulff, R. Kamm

In a previous paper1 from this laboratory, the development of a lead grid method for exploring the distribution of strain and density within metal powder compacts was described. In that work thin lead foil with rectangular holes cut at regular intervals was inserted with the powder fill, the arrangement pressed and then radiographed to permit measurement of the deformation of the lead grid. Densities at each grid element obtained in this manner were plotted as a function of the die dimensions. From such plots it was found that the densest part of a compact pressed from one side (the top) is at the top outer region and the least dense at the bottom outer region of the specimen. The axial density maximum occurs more often nearer the bottom than at the top. As a result of such exploratory measurements, it appeared reasonable to conclude that variations in density could be attributed in the main to die wall friction. Thus compacts of large diameter appeared relatively uniform in density except where the die fill had been uneven. Finally it was found that lubrication of the finely finished die cavity contributed more to magnitude and uniformity of density within the compact than interparticle lubrication. Since publication of the above results, it was found that circular-hole grids could be more accurately made and, when deformed within the powder, more readily measured and analyzed. Much of the former work was repeated and new results which include the effect of lubrication, compact height, pressure, speed of pressing and vacuum pressing are reported in the present paper. Circular-hole Grids and Analyses OF Radiographs Commercial lead sheet 0.008 in. in thickness was used in all the work reported. The 0.0938-in. diam holes were punched in the sheet on 1/8-in. centers to an accuracy of 0.001 in. The finished grid used contained eight or more holes in a row and from I to 24 rows. The lead sheet was clamped between two pairs of brass strips bolted to a small milling machine table which was itself bolted to a bench in correct position near a vise which held the punch. Travel of the lead grid in two dimensions was controlled by two steel lead screws calibrated in 0.001-in. divisions. A stripper plate was used on the punch to avoid distortion of the lead foil. A high carbon-high chromium (chrocar) one-piece steel die was used throughout the work. The die cavity was 1.125 in. in diam and the clearance between plungers and die wall was 0.001 in. The die was also used for pressing from both ends with two long plungers. Finally, lapping of die and plungers gave a surface whose rms value On an Abbot profilometer was 5 micro-in. The die walls and plungers were, except where otherwise noted, lubricated with a stearic acid suspension in benzene. This was put on in multiple layers and allowed to dry before filling the die.

Jan 1, 1949

By L. C. St. Arnaud

"Open pit mines can produce large disturbances within regional hydrogeologic systems. The degree of disturbance and the consequences on the local environment depend on the size of the pit and on the physical setting of the mine. Comparisons and contrasts are presented for three Noranda base metal open pit mine sites.The Brunswick Mining and Smelting No 6 open pit has a surface area of 11 ha and a depth of 185 m. It is located within complexly deformed schists and meta-volcanic rocks. The massive sulphide and iron formations visible along the north and southwest walls of the pit generate acid drainage. Mining ceased in 1983, and the pit is presently being filled with waste rock and neutralized drainage water. Water balance calculations estimated a total fill up time of sixteen years. As the water level rises, leakage to groundwater could take place across a fault zone intersecting the pit.The Mattabi Mines F-Group pit has a surface area of approximately 3 ha and a depth of 50 m and is also set in meta-volcanic rocks and acid generating iron formations. Production at this site ceased in 1982, and the low pH pit water is neutralized and pumped into a nearby lake at least every five years. Major water inflows are from precipitation and groundwater. Groundwater mounds within adjacent high land surrounding the pit provide a natural hydraulic barrier to groundwater flow, except for the southeast side. As a consequence, the pit water elevation is being kept below the elevation of the nearby creek in which some of the pit water could drain.The Bell Copper open pit covers an area of 40 ha and is 270 m deep. With present ore reserves, the mine might be in operation until 1992. The geology around the pit consists of andesitic tufts, siltstones and shales, and the acid generation potential of the rock is relatively low. A recent hydrogeological study estimated fill up time by precipitation and groundwater to be in the order of 260 years.With increasingly more stringent requirements for mine closure, it is anticipated that more detailed hydrological and hydrogeological studies of open pits will be required to determine post-closure environmental impacts and the suitability of open pits for mine waste disposal."

Jan 1, 1990

By K. H. Coats, M. H. Terhune

Analysis and example applications have been performed to compare the accuracy and computing speed of alternating-direction explicit and implicit procedures (ADEP and ADIP) in numerical solution of reservoir fluid flow problems. ADIP yields significantly greater accuracy and requires about 60 per cent more computing time than ADEP, not 300 or 500 per cent more as reported elsewhere. l,2 INTRODUCTION Several recent papers 1-3 discuss an alternating-direction explicit difference approximation (ADEP) to the diffusion equation. Example applications of ADEP and ADIP4 were reported to support conclusions that ADEP is comparable in accuracy to ADIP and requires one-fifth to one-third the computing time of ADIP. Applications of ADEP in calculation of two-phase flow in reservoirs was also proposed. 3 This study was performed to compare further the relative merits of ADEP and ADIP in simulation of two-dimensional flow of one and two fluid phases in reservoirs. Since two-phase flow equations are often essentially elliptic rather than parabolic, the efficiency of ADEP in solving the elliptic equation was also examined.

Jan 1, 1967

By T. McKeon, G. Luttrell

Spiral separators are commonly used to upgrade sand-sized particles in both the coal and mineral processing industries. Many plants utilize multiple stages of cleaning and/or scavenging spirals to improve recovery and/or final product grade. Field studies suggest, however, that the layout of industrial spiral circuits is often less than optimal. This oversight can usually be attributed to a failure by plant designers to consider fundamental process engineering rules that govern the layout of complex separation circuits. This article reviews some of these important rules as specifically applied to multistage spiral circuit design. Two industrial case studies, one involving the upgrading of heavy mineral sands and a second involving the cleaning of fine coal, are presented to illustrate the impact of good design protocols on spiral circuit performance.

Jan 1, 2007

By John Wulff, Robert Kamm, M. A. Steinberg

IN a previous paper1 from this laboratory, the development of a lead grid method for exploring the distribution of strain and density within metal powder compacts was described, In that work thin lead foil with rectangular holes cut at regular intervals was inserted with the powder fill, the arrangement pressed and then radiographed to permit measurement of the deformation of the lead grid. Densities at each grid element obtained in this manner were plotted as a function of the die dimensions. From such plots it was, found that the densest part of a compact pressed from one side (the top) is at the top outer region and the least dense at the bottom outer region -of the specimen. The axial density maximum occurs more often nearer the bottom than at the top. As a result of such exploratory measurements, it appeared reasonable to conclude that variations in density could be attributed in the main to die wall friction. Thus compacts of large diameter appeared relatively uniform in density except where the die fill had been uneven. Finally it was found that lubrication of the finely finished die cavity contributed more to magnitude and uniformity of density within the compact than interparticle lubrication. Since publication of the above results, it was found that circular-hole grids could be more accurately made and, when deformed within the powder, more readily measured and analyzed. Much of the former work was repeated and new results which include the effect of lubrication, compact height, pressure, speed of pressing and vacuum pressing are reported in the present paper. CIRCULAR-HOLE GRIDS AND ANALYSES OF RADIOGRAPHS Commercial lead sheet 0.008 in. in thickness was used in all the work reported. The 0.0938-in. diam holes were punched in the sheet on 1/8-in, centers to an accuracy of 0.001 in. The finished grid used contained eight or more holes in a row and from I to 24 rows. The lead sheet was clamped between two pairs of brass strips bolted to a small milling machine table which was itself bolted to a bench in correct position near a vise which held the punch. Travel of the lead grid in two dimensions was controlled by two steel lead screws calibrated in 0.001-in. divisions. A stripper plate was used on the punch to avoid distortion of the lead foil. A high carbon-high chromium (chrocar) one-piece steel die was used throughout the work. The die cavity was 1,125 in. in diam and the clearance between plungers and die wall was 0.001 in, The die was also used for pressing from both ends with two long plungers. Finally, lapping of die and plungers gave a surface whose rms value on an Abbot profilometer was 5 micro-in. The die walls and plungers were, except where otherwise noted, lubricated with a stearic acid suspension in benzene. This was put on in multiple layers and allowed to dry before filling the die.

Jan 1, 1948

By A Rojc, J Ronaszeki, C Smith

Nuclear logging was tested for the in situ determination of Fe, Si, and Al in iron ore blastholes with field tests at the BHP Billiton Iron Ore, Mount Waleback Mine. Prompt gamma neutron activation analysis (PGNAA) was used to determine percentages of Fe and Si while natural gamma logging was employed for the determination of Al. The accuracy given by nuclear logging is comparable to the accuracy provided by the laboratory analysis which was determined by taking the average of four samples collected from the cuttings deposited on the surface around the perimeter of a drill hole. The work also indicated that there is a chance of determining Al by PGNAA.

Jan 1, 2002

By Paul Billingsley

NICKEL Plate mountain coincides closely with that portion of the Hedley mining district which is of economic interest. From it has come almost the entire past production, and the active mines of the present epoch, Nickel Plate-Sunnyside and Hedley Mascot, lie in a compact group near its summit. The Hedley district, which is 210 miles due east of Vancouver, is situated in the Okanagan range of southern British Columbia, where this rather gentle uplift is deeply dissected by the canyons of the Similkameen and its tributaries. The region is essentially part of the Interior Plateau of the Province (Figure 1), but is adjacent to easterly elements of the Coast Range. The Similkameen canyon, 4,000 feet in depth and frequently less than 4 miles from rim to rim, traverses the district from northwest to southeast. The deepest and narrowest portion of the canyon lies between Hedley and Keremeos, 18 miles to the southeast. At Hedley, an important tributary, Twenty Mile creek, enters from the north in a bold canyon, making a focus of unusually rugged topography. Nickel Plate mountain occupies the sector to the east of this junction (see Figure 2) and its flanks are ringed by the cliffs of Twenty Mile canyon on the west and by those of the Similkameen canyon on the south. On the east, it slopes gently to the hanging valley of Eighteen Mile creek, and on the north, with only slight loss of elevation, it merges into the moderately hilly surface of the plateau.

Jan 1, 1941

By Madgwick J. C

The monosaccharides glucose, galactose and arabinose, and the polyols glycerol and mannitol (0.1 Ufo WIV) supported pure and mixed culture heterotrophic bacterial manganese leaching of solid pyrolusite (MnO2, 2% W/V) to yield 14-38 mg/litre manganous ion in 3 days from a simple mineral salts media at 30°C. Supplementation of pure bacterial isolates growing on glucose with soluble intracellular photosynthate from freshwater algae (0.07 g/l carbohydrate) and marine algae (0.11 g/l) led to an improvement in Mn++ yields of 24 and 100 per cent respectively. Extracellular products of the freshwater algae (0.3 g/l carbohydrate) boosted recoveries by 57 per cent.

Jan 1, 1982

By Koji Matsubara, Yoshiaki Iguchi, Shoji Hayashi

Iron ore particles of a limonite iron ore were reduced completely with H2 at 1023K to 1273K in a fluidized bed. Then, at 973K, the formed iron was exposed to HrH2S mixtures (sulfur activity, as=0.5) for 3.6ks and carbidized with CO-H2-H2S· mixtures at 0.1 MPa. During the carbidization, the particles of about 150mg were sampled at every 600s interval. The sampled particles were analyzed by XRD and chemical analysis for C and S to evaluate the content of Fe3C, Fe5C2, Fe and free carbon. The reaction extent is defined as fo=Xfc3C +xFc5c2; x is the molar fraction of Fe in Fe3C. The carbidization curves can be fitted very well to -ln(l-f0)=g(pb T)t; g(p; T) is the carbidization rate, i.e. the carburization rate on the pore surface of reduced iron. The rate is found to be nearly proportional to the specific surface area of reduced iron, a P 0 , which decreases with increasing the reduction temperature. The value of a P 0 does not change by the carbidization and the stability of the iron carbide product in the atmosphere increases with the temperature.

Jan 1, 2000

By Joseph M. Kuchta

This Bureau of Mines manual is oriented to the technical needs of an investigation of fire or explosion accidents and includes various practical and theoretical information that is needed in analyzing accidents or evaluating conditions that might lead to an accident. It is applicable to accidents in the chemical, mining, transportation, and other fuel-related industries. Specific procedures for conducting an accident investigation are outlined, and various guidelines are given for developing the fire or explosion evidence. Ignitability, flammability, and physicochemical data are presented for over 500 combustible gases, liquids, and solids; empirical and theoretical expressions are also given for extrapolating the behavior of combustible-oxidant-diluent systems to various environmental conditions. In addition, various data pertinent to damage analysis are summarized to facilitate the task of the investigator in developing plausible accident scenarios.

Jan 1, 1985

By Norman A. Jull

"Factors which affect the separation achieved in a hydrocyclone are discussed and illustrated with graphs of some mathematical relationships.Definitions of separation and sharpness include comment on use of elutriation devices.A plea is made for better evaluation of field data prior to their reporting or use in calculations. Methods of evaluation are suggested, with samples of the relevant calculations.An example of the effect of percent solids errors is given, with computer printout and plotted corrected recoveries.INTRODUCTIONThe range of interest in cyclones runs from a simple demand for classification results to a detailed study of published equations defining cyclone characteristics. Probably this group covers as broad a range and, in an attempt to offer something for everyone, I will begin with general operating comments, then move on to more analytical topics. Ideally, an author would compose his paper after the discussion period, when he would have a better idea of the areas of special interest to his audience.Sor'1e of you may share our incurable fascination with classification, especially as performed in cyclones. It is amazing that such a simple device could be in use for more than 20 years and retain as much mystery as it does. Substantial parts of the mystery have been solved but some remains, to keep up our curiosity. There is at least one valid reason: the unusual compactness of this device, which makes internal observation very difficult. What other unit can you think of which performs such a complex separation between particle sizes, shapes and specific gravities at such high capacity? Retention time in a cyclone is typically 3 seconds!Mutual Agreement - In a cyclone, every parameter of geometry and of operation interacts with every other. In an orderly discussion of individual parameters it would be necessary to repeat, in every section, 11 if all other factors are equal"". Could we agree now, for our mutual convenience, that that phrase is clearly understood between us during the remainder of this paper?"

Jan 1, 1972

By W. Reed

During the 20th century, the increased emphasis on worker health and safety and the advent of new mining equipment and methods led to many changes in mine face ventilation practices. Efforts by government and private industry to improve and modify ventilation practices resulted in better health and safety conditions for workers. This paper examines factors that had a significant influence on mine face ventilation design during the past century. Several “milestone” events are discussed along with the impact they had on worker health and safety. Significant ventilation research efforts by government and private industry are presented. This brief ventilation history highlights innovative ventilation designs and a consistent commitment to mining health and safety.

By J. M. Stuve

The present Bureau of Mines investigation measured low-temperature heat capacities of NiBr2 (8 to 302 K) and NiS04 (9 to 70 K) by adiabatic calorimetry. The standard entropies (S°, 298.15 K) of NiBr2 and NiS04 were calculated as 29.26 ± 0.06 cal/deg mole and 24.21 0.04 cal/deg mole, respectively. (1 cal = 4.1840 joules.) Heat-of-solution measurements of anhydrous NiBr2 were used to determine its enthalpy of formation (?Hf°, 298.15 K) as -50.64 ± 0.31 kcal/mole. High-temperature enthalpies of NiBr2 and NiS04 were measured by drop calorimetry to 1,150 K and 1,002 K, respectively. Enthalpies, heat capacities, and related formation functions are tabulated to 1,200 K.

Jan 1, 1978

By F P. Hao

Organo-sulphur-based collectors (eg xanthates, dithiocarbamates and dithiophosphates) are widely used in the flotation of sulphide minerals. Xanthates (ROC(=S)Sû), for example, adsorb strongly at sulphide mineral surfaces, in a reaction that is electrochemically coupled with the reduction of dissolved oxygen. One of the oxygen reduction products, hydrogen peroxide, reacts directly with dissolved xanthate, leading to its oxidative decomposition. Experimental work has been conducted, using ethyl xanthate, to understand the molecular mechanism by which hydrogen peroxide reacts with xanthates. A number of degradation products have been identified, some of which have not been reported previously. This oxidative decomposition reaction pathway is discussed in the broader context of xanthate decomposition in flotation systems. One of the identified ethyl xanthate decomposition products, ethyl perxanthate (ROC(=S)SOû), has been observed in the process water of a number of mineral processing operations. The interaction of this molecule with goethite (α-FeOOH) particles, typical of that found in tailings dams, has been studied in more detail using attenuated total reflectance (ATR)-FTIR. The ethyl perxanthate molecule has been found to coordinate to iron (FeIII) at the goethite surface, and undergo a surface-catalysed decomposition process. In the presence of both PbII and goethite, a ternary surface complex is formed, where ethyl perxanthate is coordinated directly to surface adsorbed PbII atoms. The results obtained give some insight into the environmental fate of ethyl xanthate in tailings streams, and a basis on which to consider the environmental importance of such species in tailings dams. Strategies for the destruction of residual xanthate levels in waste water streams are discussed in terms of the likely reaction products.

Jan 1, 2002

By A. T. Iannacchione

Underground limestone mines typically use the room-and-pillar method of mining in the generally flat-lying limestone formations. In some cases the dip may exceed 5° which can result in unique roof instability problems. Stability may be further exacerbated by the presence of horizontal tectonic stresses. Field studies and numerical model analyses are combined to assess the affect of the dip in various stress conditions. The results showed that where the horizontal tectonic stresses are sufficient to cause intact rock failure, increasing dip results in increased failure potential. The effect of the dip is greater when the maximum horizontal stress is parallel to the dip. Two case studies are presented and evaluated against the findings of stress analysis results. The study showed that the empirical rules of orienting headings parallel to the maximum stress are generally applicable to dipping excavations, except when mining in the up-dip direction. The importance of accurately determining the orientation of the maximum horizontal stress is emphasized because the window of favorable orientations relative to the stress is small.

By Jose R. Hernandez-Aguilar

"Three models to predict the effect of bubble size (Db) on metallurgical response were tested in a pilot-scale flotation column at Teck Highland Valley Copper mine. The column was fed with slurry collected from the Cu/Mo separation circuit. The first model was the one developed by Gorain et al. (1997), which assumes that the collection zone rate constant (kc) is inversely proportional to Db. The second model was the one proposed by Hernandez-Aguilar et al. (2010), which considers kc as an inverse square function of Db. The third model was the one developed by Yoon and Luttrell (1989) which provides expressions to describe the efficiency of particle collection (E) based on first principles. The results showed a significant bias between experimental and predicted data using the model of Gorain et al. (1997), possibly reflecting the model’s inability to explain the impact of bubble size, bubble rise velocity and flow regime on E. The model of Hernandez-Aguilar et al. (2010) well described the experimental evidence. The model of Yoon and Luttrell gave accurate and unbiased predictions. However, Yoon and Luttrell’s approach calls for a criterion to determine whether the flow regime is potential or intermediate, a subject that requires more fundamental research.INTRODUCTIONParticle collection, i.e., bubble-particle collision followed by attachment, is the basis of flotation. In a quiescent environment (such as the one observed in a column, or away from the impeller in a mechanical cell), a collision event can take place as long as the “degree of turbulence” caused by the rising bubble does not prevent particle and bubble to flow in close proximity. Upon collision, the particle slides on the bubble surface for a period of time. If the particle is hydrophobic, attachment occurs when the “sliding time” is longer than the “induction time”, which is the time required to thin and rupture the intervening liquid (usually water) film forming a three-phase contact angle. While the induction time is largely influenced by the degree of hydrophobicity of the particle, the degree of turbulence is governed by the bubble size. Generally, direct control of bubble size is not exercised by most mineral processing practitioners, in spite of its obvious importance. Studies to model the effect of bubble size on particle collection using fundamental approaches have been conducted (e.g., Anfruns and Kitchener, 1977; Webber and Paddock, 1983; Yoon and Luttrell, 1989; Dai et al., 1999). However, these models have been validated under highly idealized laboratory conditions (micro-scale experiments using single minerals and uni-sized bubbles), far from resembling those existing in practical industrial applications. Fundamental studies to interpret the effect of bubble size on particle collection in industrial environments are largely absent in the literature. Partly because of this lack of practical knowledge, many mineral processing practitioners perceive laboratory “bubble size” studies to be valuable academic exercises, but not something that can be directly applied to daily production issues."

Jan 1, 2011

By Emmanuel N. Zevgolis Ismene-Polyxeni Kostika

Keywords: reduction, kinetics, laterites, rotary kiln, dust In this work, the reduction kinetics of dust from nickeliferous Greek laterites is investigated. The dust is a by-product from laterite treatment in rotary kilns and it comes from washing towers, electrostatic filters and polycyclones. Laboratory made pellets from this dust were also examined. Reducibility was studied in the temperature range of 700°C to 850°C in a laboratory tube furnace. Kinetic analysis of the results showed that at lower temperature values the mixed kinetic model verifies the experimental results of dust and pellet samples. At higher temperatures (800° and 850°C) diffusion becomes the rate controlling mechanism. The calculated activation energy values verify also the above mentioned results.

Jan 1, 2005

By MATTHEW HART, THOMAS BAMFORD, Kamran Esmaeili, MICHAL KOWALCZYK, FILIP MEDINAC

Improved haul-road conditions can have a positive impact on mine operations, resulting in heightened safety, productivity gains, longer tire life and lower maintenance costs. For these reasons, a monitoring program is required to ensure the operational efficiency of the haul roads. Currently, at Bald Mountain Mine, monthly site severity studies, ad hoc inspections by frontline supervisors or operator feedback reporting are used to assess road conditions. These methods are subjective and provide low temporal resolution data. This case study presents novel unmanned aerial vehicle (UAV) technologies, applied on a critical section of haul road at Bald Mountain, to showcase the potential for monitoring haul roads. The results show that orthophotos and digital elevation models can be used to assess the road smoothness condition and to check the road design compliance. Moreover, the aerial mapping allows detection of surface water, rock spillage and potholes on the road that can be quickly repaired/removed by the dedicated road maintenance team.

Mining at Waihi on the Martha Hill commenced in 1878 and between 1892 and 1953 produced 35 million ounces of bullion from some 13.5 million short tons of ore from 40 named quartz reefs. The general geology of the ore is recorded in detail with differing interpretations by Bell and Fraser (1912) and Morgan (1924). The reefs and stringers have formed by fissure filling and replacement in mainly quartz andesite dacite flows within the Waihi 'Graben'. The host rocks are extensively propylitised with intense alteration forming zones of kaolin adjacent to the main reefs.

Jan 1, 1979