Search Documents

By Z. Szczepanik, D. Milne, K. Kostakis

Abstract This paper presents the results of a series of creep tests performed on a total of nine samples of Lac du Bonnet granite from the Underground Research Laboratory near Pinawa, Canada. Each of the nine samples were subjected to stresses in excess of 80% of the average uniaxial compressive strength of the granite and were maintained at that level of constant loading for periods of time ranging between a few minutes and several months. Acoustic emission was recorded in order to monitor the development and accumulation of brittle microfracture damage in the samples throughout the long-term loading. According to previously published theoretical predictions and field results, as well as similar experimental results of creep tests in granite, samples should fail when loaded to 70% of their UCS for an extended period of time. Six of the samples did not fail when subjected to stresses in excess of 80% of their UCS over periods of several months and were subsequently subjected to uniaxial compression to failure. The average strength of the samples that had previously been subjected to long-term loading were comparable to the average published strength of this rock. Three of the nine samples had increased end confinement and these three samples failed under long term loading. Résumé Cet article présente les résultats d'une série d'essais de fluage de roche exécutés sur neuf échantillons de granite de Lac du Bonnet, du laboratoire souterrain de recherches près de Pinawa, Canada. Chacun des neuf échantillons a été alors soumis aux charges au-dessus de 80% de la résistance à la UCS moyenne du granit et a été maintenu à ce niveau du chargement constant pendant des périodes s'étendant entre quelques minutes et plusieurs mois. L'émission acoustique a été enregistrée pendant les essais afin d'obtenir des indications des dommages pendant le chargement à long terme. Selon des résultats théoriques précédemment édités et les résultats expérimentaux semblables des essais à long terme en granite, échantillons devrait échouer si chargé à 70% de leur UCS pendant une période prolongée. Six des échantillons n'ont pas cassé quant ils ont été soumis aux charges au-dessus de 80% de leur UCS et ont été plus tard soumis à la compression uniaxiale à la rupture. La force moyenne des échantillons qui avaient été précédemment soumis au chargement à long terme étaient comparable à la force éditée moyenne de cette roche. Trois des neuf échantillons avaient augmenté le confinement de fin et ces trois échantillons ont cassé sous le chargement à long terme. Zusammenfassung Dieser Artikel beschreibt die Resultate von Kriechversuchen, die an neun Proben aus dem Lac du Bonnet Granit des "Underground Research Laboratory" bei Pinawa in Kanada durchgeführt wurden. Jede der neun Proben wurde Drücken unterworfen, die mehr als 80% der einaxialen Druckfestigkeit des Granites entsprechen. Diese Drücke wurden für verschiedene Zeitspannen von wenigen Minuten bis zu einigen Monaten auf einem konstanten Niveau gehalten. Während der gesamten Langzeitbelastung wurden akustische Emissionen aufgezeichnet, um die Entwicklung und gesamthafte Beschädigung der Proben durch Sprödbruch aufzuzeichnen. Entsprechend bisher veröffentlichter theoretischer Vorhersagen, Feldversuchen und auch experimentellen Resultaten von Kriechversuchen an Granitproben wäre ein Versagen der Proben zu erwarten gewesen, wenn sie über längere Zeit einer Last von 70% ihrer einaxialen Druckfestigkeit unterworfen werden. Wider Erwarten trat bei sechs der Proben kein Versagen ein, als sie mit über 80% ihrer einaxialen Druckfestigkeit über mehrere Monate belastet wurden; daher wurden sie im Anschluss bei einaxialer Kompression zum Versagen gebracht. Die mittleren Festigkeiten der im Langzeittest verwendeten Proben sind vergleichbar mit den normalerweise für diesen Gesteinstyp angegebenen Festigkeiten. Drei der neun Proben versagten unter der Langzeitbelastung; diese drei Proben hatten eine erhöhte Endflächenreibung.

Jan 1, 2003

By B. D. Sartwell

Multiple-charged beams originating from a 300-kv ion accelerator are important tools in the study of metal surfaces and thin films. A knowledge of the particle range is necessary for an understanding of the interaction processes of the ions with the targets. Utilizing a theory developed by Lindhard for determining the range of low-energy ions in solids, the ranges of H, He, C, N, 0, and Ar ions in A1203, Al, Fe203, Fe304, CuO, Cu20, Fe, Cu, Sn, and W were calculated for the energy range 60 to 400 kev using a computer program written in BASIC. The range, presented in graphical form, is given in both µg/cm2 and angstroms. In addition, heavy ion ranges were calculated for comparison with published experimental values. For ions with Z > 5, the discrepancy between the calculated values and published experimental values generally ranged from 2 to 40 percent; the largest deviations were probably due to experimental error.

Jan 1, 1970

By John C. Gagliardi

The size and complexity of modern surface haulage trucks has resulted in an increased reliance upon sensors and electronic-based instrumentation for safe and efficient operation. Design engineers need accurate information about the equipment vibration environment to efficiently and effectively build components for installation on mobile mining equipment capable of withstanding the mine environment. Examples of such components include backup alarms, communication equipment, microprocessor-based controllers, and a wide variety of sensors. Unfortunately, this information is not available to the majority of both original equipment and aftermarket equipment manufacturers. To address this problem, the U.S. Bureau of Mines performed field vibration measurements on a variety of surface mining haulage trucks. The vibration measurements were then analyzed and test specifications were developed in the form of envelopes. In conjunction with test specifications, recommendations to aid manufacturers in implementing a vibration environment test program have been included with an illustrative example.

Jan 1, 2010

By J. W. Senn

A magnesium alloy modeled after commercial alloy WE54 was thermomechanically processed and characterized to understand the mechanisms by which its texture can be randomized, as reported by Ball and Prangnell [1]. Samples were deformed in plane strain compression to prescribed strain levels at temperatures high enough to prevent cracking and then recrystallized. The deformation texture is very similar to that observed after plane strain compression (e.g., rolling) of other Mg alloys, such as common AZ31. However, the texture can radically evolve during recrystallization. Annealing above the precipitate solvus temperature results in a nearly random recrystallization texture where the initially strong basal texture is completely eliminated. Annealing below the solvus temperature produces a recrystallized texture similar to conventional Mg alloys, i.e., a weakened basal texture. If this same material is then annealed above the solvus to promote grain growth, a randomized texture evolves, which is similar that of samples simply recrystallized above the solvus. It is hypothesized that a sort of preferred growth mechanism, whereby grains with random orientation grow faster than those with the original basal texture, contributes significantly to the texture randomization observed in wrought magnesium alloys containing rare earth elements.

Jan 1, 2006

By Chandrasegaran, Tamilmani

"This paper describes a case study of a retaining wall structure using a diaphragm wall to construct a stilling basin at Tanjung Bin T4 power plant in Johor Bahru, Malaysia. The stilling basin is part of the Phase IV (T4) 1x1000MW power plant’s offshore cooling water discharge culverts. The site is located close to the sea with 5m of fill on top of very soft sediments of marine origin up to 20m thick underlain by fluvial clay and metasedimentary rock. Stringent wall deflection criteria and construction program dictated adopting an efficient solution with 800mm thick diaphragm wall supported by permanent top support as the temporary prop and improved horizontal restraint provided by deep mix piles acting as a slab (ground improvement layer) below the final excavation level. The depth of excavation is about 10.12m from the existing ground level. The proposed solution kept the wall deflection below the limit of 0.7% of the depth of bulk excavation and avoided additional props leading to faster completion of the structure. With unsymmetrical loading behind the retaining walls, 2D finite element analysis was carried out to assess the wall deflection and stresses in the wall and the grout layer below. The diaphragm wall is instrumented to monitor the behavior and the findings are discussed in the paper.INTRODUCTIONConstruction in soft marine clay has always been a challenge to the engineer because of its very low shear strength and its sensitivity to disturbance. In the case of excavation projects the problem becomes even more complicated with development of excess pore pressure during excavation. Marine clay with its low shear strength and lesser passive resistance, generally leads to large wall movements and settlement behind the wall. Increased passive resistance coming from increased number of props is useful but has its limits and it is no longer the most effective way in containing or reducing the wall movements or forces in the wall. One of the solutions to these problems is to improve the soil shear strength by means of ground improvement infront of the wall at an elevation most appropriate to maximize wall performance. There are several methods adopted in improving a soil layer including mixing additives to the ground to improve the shear strength to partially replacing the weak soil while others are fully replacing the weak soil. This paper discusses the case study of approximately 10m of excavation in soft marine clay using 800mm thick diaphragm wall supported by Deep Mix Piles (DMP) being used to improve soft marine deposit to form a slab just below the formation level and thus improving passive resistance significantly. The ground improvement layer helped to reduce the wall forces and deflections making it possible to remove the need for additional temporary props leading to significant savings is time and productivity. The paper presents the various options explored before this method is adopted, the design approach, instrumentation data and the monitored results."

Jan 1, 2015

By Travis Knight

Mixed uranium and refractory metal carbide systems have been proposed for space nuclear power and propulsion applications. Solid-core space nuclear reactors could be utilized for low- earth-orbit (LEO) to geosynchronous-earth-orbit (GEO) transfers, manned missions to the moon or mars, and orbiter missions to the outer planets. However, these high performance space nuclear reactors present some challenging materials engineering requirements for operating in a high temperature, high radiation, and hot hydrogen environment. Since the RoverNERVA programs were concluded in 1973, significant advances in ultrahigh temperature materials technology have been made which can be applied to the development of an advanced solid-core nuclear fuel. Nuclear thermal propulsion (NTP) was first studied in the U.S. beginning in the mid-1950's during the RoverNERVA programs. During that time, about 20 rocket reactors were built and tested. More recently, Russian nuclear rocket reactor tests with pseudo-ternary carbide nuclear fuels (U, Zr, Nb)C and (U, Zr, Ta)C have been operated at temperatures as high as 3300 K for one hour. This study examined the processing parameters for fabricating the pseudo-ternary carbide, (U, Zr, Nb)C.

Jan 1, 1999

By Nixon J. C, Reynolds C

Three principal features of the ore at Captain's Flat, New South Wales, tend to complicate concentration of the valuable minerals, these being:1. The ore occurs in three more or less separate bodies which vary in texture and mineral ratios. Mining of constant proportions of the three sections, or adequate blending of the ore, is not fully effective, and consequently the flotation section is subjected to feedof varying texture.2. The mineral association in the heavily pyritic ore is extremely intimate. Composite particles exist even at 20 micron sizeI, and probably finer.3. The copper content of the ore averages_about 0,6%, which is high enough to justify recovery of the chalcopyrite in a separate concentrate. A review of the metallurgical history of the mine shows that this feature has been the cause of the several major changes in flowsheet of the flotation section since the commencement of milling.METALLURGICAL HISTORYThe mine started production in January 1939, at the rate of 250 tons per day of sulphide ore, assaying 0·68% Cu, 6·52% Pb, 10·8% Zn, and about 1 dwt. Au and 2 oz. Ag per ton.

Jan 1, 1952

By Anna Carolina Cerqueira Neves

Synthetic fiber has been gradually replaced by natural fiber, such as lignocellulosic fiber. In comparison with synthetic fiber, natural fiber has shown economic and environmental advantages. The natural fiber presents interfacial characteristics with polymeric matrices that favor a high impact energy absorption by the composite structure. However, until now little has been evaluated about the hemp fiber incorporated in polymeric matrices. This study has the purpose of evaluate the impact resistance of this kind of epoxy matrix composite reinforced with different percentages of hemp fibers. The impact resistance has substantially increased the relative amount of hemp fiber incorporated as reinforcement in the composite. This performance was associated with the difficulty of rupture imposed by the fibers resulting from the interaction of hemp fiber / epoxy matrix that helps absorb the impact energy.

Aug 16, 2017

By J. J. Talja

An investigation of oxidation of various nickel concentrates was carried out using differential scanning calorimetry (DSC). The aim of this study was to determine the ignition temperature and investigate other oxidation behavior of various sulfide-based nickel concentrates. Variables in the experiments were mineralogy, particle size and partial pressure of oxygen with temperature increasing linearly at 25 K/min from 323 to 1023 K (50-750 °C). The igni¬tion temperature was determined to represent the starting point of rapid oxidation. The reac¬tion enthalpies of the concentrates were determined and the amount of heat generated up to various time were used to calculate the extent of reaction. Mineralogical changes at various stages of oxidation were also investigated. For this purpose a second set of DSC-experiments were carried out in which each experiment was interrupted at a desired temperature between 673-873 K. From these tests the weight loss of samples were determined and changes in the individual constituent of sulfide minerals were analyzed. For pentlandite-based Ni-concentrates the ignition temperature was 705-710 K (approximately 435 °C). Pyrite was the first sulfide to oxidize. Reactivity of the violarite-based concentrate was greater than those of the pentlandite-based concentrates. The stoi-chiometry of pentlandite changed before ignition because of preferential oxidation of iron. Rapid oxidation of the pentlandite mineral occurred at about 823 K (550 °C). By 900 K about 90 % of the iron in pentlandite was converted to hematite, and NiS containing some iron was formed.

Jan 1, 1994

By Francisco Geraldo Toledo Junior

Os aços inoxidáveis possuem características essenciais para um bom acabamento quando o que se busca é estética e boa resistência à oxidação. Quando se específica um aço inoxidável, o acabamento é um dos aspectos relevantes que devem ser considerados. O acabamento possui uma importante influência em algumas características do material como, por exemplo, na facilidade da limpeza e na resistência à oxidação / corrosão. Há uma grande variedade de acabamentos. Através de ensaios de oxidação a quente, medição de potencial eletroquímico, medição de dureza a baixa carga (microdureza) e medição da tensão residual via difração de raios x foi possível perceber uma diferença entre os acabamentos 2D, 2B, RO, BB, Nº4 e Nº6. A medição de tensão residual mostrou qualitativamente que o aumento de dureza e o forte amarelamento ocorrido no material com determinados acabamentos é função de uma deformação elástica na superfície imposta durante alguns dos processos de fabricação desses aços. Esse mecanismo é relevante e interfere na resistência a oxidação e corrosão nos casos estudados.

Aug 17, 2017

By E. F. Foerster

The Bureau of Mines used a diphenyl ether calorimeter to determine the heat contents of natural and synthetic blast-furnace slags. For solid slags, enthalpy (HT-H298) at 1,448° to 1,680° K ranged from 282.1 to 348.5 cal/g (±3 percent); liquid slag values were 400.1 to 514 cal/g (±3 percent) in the temperature range between 1,626° and 1,890° K. Experimental results for liquid slags were 14.3 to 16.2 percent higher than the enthalpies calculated from thermodynamic tables; values for solid slags ranged from 5.3 percent lower to 3.9 percent higher than calculated values. Experimental results for liquid synthetic slags ranged from 14.9 to 24.3 percent higher than the calculated enthalpies; values for solid synthetic slags were from 1.0 to 3.4 percent higher.

Jan 1, 1967

By W. K. Collins, C. L. Dahlin, D. C. Dahlin, W. K. O’Connor, G. E. Rush

Direct mineral carbonation has been investigated as a process to convert gaseous CO2 into a geologically stable final form. The process utilizes a slurry of water, with bicarbonate and salt additions, mixed with a mineral reactant, such as olivine (Mg2SiO4) or serpentine [Mg3Si2O5(OH)4]. Carbon dioxide is dissolved into this slurry, resulting in dissolution of the mineral and precipitation of magnesium carbonate (MgCO3). Optimum results have been achieved using heat pretreated serpentine feed material and high partial pressure of CO2 (PCO2). Specific conditions include: 155°C; P002=185 atm; 15% solids. Under these conditions, 78% conversion of the silicate to the carbonate was achieved in 30 minutes. Process mineralogy has been utilized to investigate the appropriate feed characteristics, identify the process products, and interpret the mineral dissolution and carbonate precipitation reaction paths.

Jan 1, 2001

By O. W. Simmons, L. W. Eastwood, C. M. Craighead

Binary alloys of titanium with silver, lead, tin, nickel, copper, beryllium, boron, silicon, chromium, molybdenum, manganese, vanadium, iron, and cobalt were studied. One-half-pound ingots of the alloys were prepared in an arc furnace, employing a water-cooled copper crucible, an argon atmosphere, and a water-cooled tungsten electrode. The half-pound ingots were fabricated by forging at 1700°F in air to 1/4-in. slab, followed by hot rolling at 1450°F to 0.060-in. sheet. Tensile properties, minimum bend radii, hardnesses, response to heat treatment and aging treatment, and phase relationships were determined for these alloys. EARLY in 1947, as one phase of the evaluation of materials for Air Force Project RAND, Battelle successfully arc melted Bureau of Mines titanium and obtained a few basic properties of unalloyed titanium and several titanium-base alloys. The low density, excellent resistance to corrosion, and high tensile properties of these materials stimulated a great deal of interest among metallurgists and designers seeking better materials of construction. As a result of this early work, Battelle, under contract with the Air Materiel Command, Wright-Patterson Air Force Base, has continued extensive studies of titanium alloys. The result of the first year's work is described in three papers. The present one deals with binary alloys, the second with ternary alloys, and the third paper with quaternary alloys. Melting Method The arc furnace for melting titanium and other refractory metals was developed at Battelle Institute under Air Force Project RAND. During the present work, considerable improvement has been made in the design and operation of this furnace for making small ingots of titanium and titanium alloys. The improved furnace design is illustrated by fig. 1, which shows a cross-sectional view with the dimensions of various parts and their relationship to one another. The essential features of the furnace are the inert argon atmosphere, the water-cooled copper crucible, and the water-cooled tungsten elec- trode. The melting crucible is formed by spinning 0.064-in. annealed copper sheet. A groove for an O-ring seal is spun into the flange of the crucible. A fiber gasket between the crucible flange and the water-cooled brass cover provides electrical insulation. The brass cover is fitted with a sight glass, an opening for the water-cooled electrode, and a tube through which the material is charged. Direct current is used for melting, with the positive electrical terminal connected to the water jacket and the negative terminal to the electrode. A typical heat is made in the new furnace as follows: Approximately, 0.20 lb of titanium under 2 mesh per in. and the alloy addition, if any is to be used, are placed in the bottom of the crucible. The cover is clamped on the crucible so that the O-rings make a tight seal. The remainder of the charge is placed in a glass bottle, and this is connected by a rubber hose to the charging tube of the furnace. The crucible and the charge are evacuated with a mechanical pump to a pressure below 50 mm of mercury, or less if desired, and held at this reduced pressure for 5 min. Hot water is circulated through the jacket during the evacuation period to assist in outgassing the crucible. Following the evacuation, tank argon of 99.92+ pct purity is flushed through the crucible for 5 min and then adjusted to give a positive pressure of 1 to 2 psi. During subsequent operation, an argon pressure regulator introduces only enough argon to compensate for the small leakage which occurs through a mercury trap. Re-evacuation and reflushing the melting chamber with argon produced a negligible reduction in contamination. Two 550-amp generators, connected in parallel, constitute the power source. Normally, about 800 amp are used for melting alloys which are not extremely refractory. The generators are set for 90 v open circuit and 200 amp. The arc is struck and the electrode is withdrawn to produce an arc of 23 to 26 v. This voltage is maintained while the electrode tip is moved slowly around a circle 1 in. smaller than the diameter of the ingot. The current

Jan 1, 1951

By Diogo Peixoto Cordova, Italo Gomes Gonçalves, Andre Cezar Zingano

The top-down extraction sequence in the sublevel open stope method relies on rib pillars to support excavations, making pillar and stope stability crucial for controlling dilution. This study introduces an integrated methodology using a genetic algorithm to optimize the layout of open stopes and rib pillars while considering both economic and geomechanical performance. The methodology incorporates user-defined parameters such as the minimum size of stopes and pillars, maximum accepted dilution and acceptable percentage of pillar failure. A profit function that attributes economic value to the geometric configurations, including geomechanical performance, is employed. The geomechanical performance, assessed using numerical models in FLAC3D, includes the average percentage of pillar failure and potential dilution. The study was tested on a mining panel from an underground gold mine using a top-down mining sequence. The optimization achieved an 8 percent increase in net profit compared to the traditional engineer’s design when 70 percent hangingwall support efficiency was assumed, and a threefold reduction in pillar failure percentage. When no hangingwall support was considered, the net profit increase reached 22 percent. These results demonstrate that the proposed methodology enables integrated optimization, balancing mining costs with geomechanical performance and reducing the need for secondary support compared to traditional methods

Nov 1, 2024

By Karl J. C. Harries

"The Table of Contents that follows is only an example and is the Table of Contents from an actual negotiated agreement. It is merely intended to show how an agreement might be set out and the nature of possible provisions. As a negotiated agreement the format was dictated by the negotiations. It is not offered as a precedent of what should be contained in a joint venture agreement (“JVA”), the “proper” sequence of Articles, or a complete listing of the contents of joint venture agreements generally. The set-up used for an agreement should be decided by the parties and be one they consider flows in a logical and workable sequence. This example sets out the “deal” first, followed by the provisions relating to how work is to be carried out and then by administrative provisions necessary to make the agreement work. If you are more comfortable with, say, having the Committee provisions at the beginning, by all means have it drafted that way -- you are going to have to live with the agreement and work under it.Notes:1. The Table of Contents provisions appear in bold print. The italicized sections are annotations, which have been provided in some cases where the heading may not clearly describe the contents. They are not intended to be comprehensive, but refer to some specific matters that are considered to be of interest or to need some clarification.2. The subject matter of many of the articles and paragraphs is discussed or commented upon in the text of the book. Some of section cross-references have been provided. Such references are only to sections where the topic is a principal subject and no attempt has been made to provide a comprehensive indexing.3. Although this particular agreement is a three-party agreement, *B* and *C*, the Owners, are required to act as a unit (see para. 1.09. – § 8.44.), making the agreement effectively a two-party agreement. The parties insisted upon having a decision-making Committee and structuring the agreement accordingly. As is explained in § 8.11., such an arrangement is not recommended and can result in problems.5. See also §§ 8.24., 8.41. and 14.13. for discussions on tables of contents, summaries, and headings."

Jan 1, 2003

By Mariana Alves de Carvalho

O desenvolvimento da indústria e a redução do ciclo de vida de eletroeletrônicos aumentam a geração dos chamados resíduos de equipamentos eletroeletrônicos (REEE). Dentre os REEE, as placas de circuito impresso (PCIs) apresentam um teor de metais em sua composição que as torna importante objeto de estudo visando a recuperação destes metais para fins econômicos e, por conseguinte, impede que sejam dispostos no meio ambiente. O presente trabalho tem por objetivos a caracterização de uma amostra de placa mãe de computadores obsoletos e posterior recuperação dos metais via duas rotas hidrometalúrgicas de lixiviação ácida e lixiviação ácida em meio oxidante. A primeira etapa foi realizada com ácido sulfúrico 2M por 18 horas e a 95°C; a segunda etapa, de lixiviação em meio oxidante, utilizou também o ácido sulfúrico 2M como agente lixiviante, e o peróxido de hidrogênio como agente redutor, por 6 horas e a 95°C. As duas rotas se diferenciaram entre si na proporção sólido-líquido, sendo a primeira de 1:10 e a segunda de 1:20. A rota com proporção 1:20 foi a que apresentou resultado mais positivo, com 100% de lixiviação de Ag, Al, Cu, Fe, Ni e Zn.

Oct 30, 2017

By Neil J. Dahmen, Howard J. Handewith

INTRODUCTION Tunneling machines were introduced into civil con¬struction in the 1800s, but their practical applications were not realized fully until the 1950s. As of 1977, tunneling machines were being used on most tunneling projects of substantial size. As in civil construction, the mining applications of tunneling machines have included long drives such as tunneling for long ore-body develop¬ment drifts, long haulage tunnels, longwall access drifts, and long crosscut developments. Tunneling machines ranging from 1.75-m (5.7-ft) to more than I1.0-m (36-ft) diam are available from several manufacturers; machines for mining applications generally have ranged between 1.75 and 6.0-m (5.7¬and 20.0-ft) diam. Tunneling machines usually operate at or near horizontal grades and are supported by a rail-haulage backup system. However, declines and inclines have been made using alternative backup equip¬ment. Either circular or shaped tunnels may be bored, depending upon the particular equipment used. Using tunneling machines to bore openings through rock offers several advantages over the use of the drilling and blasting technique. These advantages include a rapid advance, continuous operation, uniformity of the opening size, smooth walls, and safe working conditions. Compared to drilling and blasting, boring reduces the disturbance of adjacent rock, thereby reducing the ground-support requirements and the exposure to water inflows. The smooth walls provide natural arching and present minimum resistance to the flow of air. A tunneling machine should be considered a spe¬cialized mining tool that is well-suited to certain mining applications. Properly applied and sustained, a tunnel¬ing machine contributes to realizing substantial econo¬mies in the development of underground mines. All costs herein are expressed in 1977 US dollars, unless otherwise noted. The mention of trade names and manufacturers is not intended to imply an endorse¬ment of any specific equipment. TYPES OF TUNNELING MACHINES As listed in Table 1, five principal types of tunneling machines were being manufactured in 1977. Each type of machine offers a special solution to a specific mining problem. Although each of these types of machines is described herein, most of this chapter is devoted to the full-face rotary rock-tunneling machine that has demon¬strated the greatest production in both civil construction and mining applications. Full-Face Rotary Rock-Tunneling Machines As shown in Fig. 1, a full-face rotary rock-tunneling machine consists of a rotating head that is fitted with rock-cutting tools and is forced into the tunnel face. This head is supported by a bearing on a structural support member that, in turn, is held in place by a hydraulically positioned wall-gripping mechanism. Both torque and thrust are reacted from the cutterhead, through the structural support and gripper mechanism, and to the tunnel wall. The rock cuttings fall to the invert at the tunnel face, and they are removed by means of cutterhead buckets or scoops that transfer the cuttings to a conveyor belt. After advancing the cutter¬head through a preset boring stroke, the tunneling machine is advanced by hydraulically pulling the gripper mechanism in from the tunnel walls, stroking forward, and resetting the gripper to the new forward position on the wall; the machine then is set for the next advance stroke. Full-face machines cut only circular openings. Ma¬chines with diameters as small as 1.8 m (6 ft) and as large as 6.1 m (20 ft) have been used in mining applica¬tions, excavating rock with unconfined compressive strengths in excess of 276 000 kPa (40,000 psi). Although special machines have been designed to turn on a radius of 30 m (100 ft) in both horizontal and vertical directions, the conveyors and backup sup¬port equipment generally limit tunneling machines to turns with a radius of more than 60 m (200 ft). The full-face rotary rock-tunneling machines have provided the fastest and most reliable production of any mining method or machine. These machines can be equipped to place any of a variety of ground-support systems, and they can be provided as "open" machines, as shown in Fig. 1, or as "shielded" machines, as shown in Fig. 2. The open machines have the advantage of allowing the ground to be supported as near to the tunnel face as possible. The shielded machines have been designed principally to allow placing precast con¬crete segments. The shielded machines completely pro¬tect the equipment and personnel at the heading, but they are economically limited to permanent long-life haulageways where full lining is required. Partial-Face Rotary Rock-Tunneling Machines As shown in Fig. 3, the partial-face rotary tunneling machine is equipped with a cutterhead that rotates slowly at about 0.21 rad/s (2.0 rpm). The single-disk cutterhead produces the tunnel section shown in Fig. 4 by means of an oscillating motion. These machines work on the undercutting principle, and they are avail¬able in spring-line dimensional increments of 0.1 m (0.32 ft) from 1.5 to 2.1 m (5.0 to 7.0 ft); the vertical dimensions are 2.4 to 3.2 m (8.0 to 10.5 ft), respec¬tively. Depending upon the tunnel width, the cutterhead disk may be fitted with from 8 to 16 drag-bit cutters. Penetration is achieved by means of hydraulic rams that force the tungsten-carbide bits into the rock mass. The operation is cyclic, with cutting occurring only on the upstroke. On the downstroke, the rotating cutter¬head draws the fallen muck from the invert into the panzer-type conveyor for rearward transfer. This feature allows time to either reposition ore cars or to exit the tunnel with muck trains while the machine is cutting, as shown in Fig. 5. Boom-Type Rotary Excavators The boom-type rotary-excavator tunneling machines commonly are known as boom-type continuous miners

Jan 1, 1982

By G. Birkbeck, T. C. Wells

Pearlite morphology in three commercially produced, low-carbon steels has been studied using optical and electron microscopy. A reduction in the cooling rate from 600° to 6°C per hr increased the interlamellar spacing but had little effect on pearlite content. The form of the lamellae was also assessed in terms of a new parameter, the ratio of lamellae length to interhmellar spacing. The variation of this parameter with cooling rate depended on steel composition. For each steel, it would appear that an optimum cooling rate exists at which lamellar pearlite can be produced to the greatest extent, though not necessarily the same extent in different steels. PeARLITE morphology depends principally on steel composition, prior austenite grain size, and either cooling rate or isothermal transformation temperature. Alloying with manganese,'" fine grain size,374 and slow cooling rates reduce the likelihood that a well-developed lamellar structure will be produced. Instead, imperfect structures usually consisting of partly globular carbides are formed in a ferrite matrix. Such structures have been described as granular.1,2,5 degenerate,6 or semi4-pearlite. Manganese additions also progressively lower the eutectoid temperature and the carbon concentration at the eutectoid so so that, for a given carbon content. the pearlite fraction is increased as manganese is added. While the effects of manganese are understood in a general way, quantitative studies of pearlite morphology have been carried out mainly on steels of eutectoid composition;9 little quantitative data is available for low-carbon steels. Certain anomalies exist in the behavior of steels containing -1.5 pct Mn, however. The pearlite morphology in niobium-treated steel differs from that which is generally accepted as typical of low-carbon/manganese steels in that a reasonably well developed lamellar structure is sometimes observed. In the present work, the effects of changes in cooling rate from 600° to 6°C per hr on the pearlite morphology in three commercially produced, low-carbon steels have been studied by both optical and electron microscopy. I) MATERIALS The steels were of the following types: 1) 0.1 pct C, 0.4 pct Mn steel (En 2, a composition similar to specification SAE 1010); 2) niobium-treated, 0.2 pct C, 1 1/2 pct Mn steel (BS 968:1962); 3) silicon-killed 0.2 pct C, 1 1/2 pct Mn steel (En 144, a composition similar to SAE 1320). The chemical analysis for each steel is given in Table I. To facilitate the comparison of pearlite morphology in the three steels, steels 1 and 3 (which were obtained as 1/2-in. plate and 1-in.-diam bar, respectively) were hot-rolled in the laboratory to $ in. thickness, finishing at around 850°C. The BS 968:1962 was received as 1/8-in. plate finished at 885°C and was not further worked. Specimens from each steel were heat-treated in vacuo at 950°C for 1 hr and cooled at rates of 600°, 60°, and 6°C per hr. 11) EXPERIMENTAL Pearlite contents were determined by point counting (500 points) on longitudinal sections mechanically polished and etched in 2 pct nital. Pearlite morphology is usually considered in terms of interlamellar spacing. For pearlite colonies randomly distributed in space and having a true, constant interlamellar spacing So Pellissier et al.9 determined the distribution curve for the apparent spacings of the lamellae on a random section plane. The areal fraction fs of the pearlite colonies occupied by apparent spacings up to a limiting value S is given by:

Jan 1, 1969

By Álvaro Ordóñez Núñez

El presente texto describe la forma de realizar la extracción y recuperación de cobre y zinc a través del empleo del hipoclorito como agente oxidante y del amoniaco como agente acomplejante de los cationes metálicos. Entre las ventajas de su utilización respecto a la lixiviación tenemos: que las soluciones obtenidas son más limpias y los interferentes como el hierro, manganeso y aluminio se precipitan como óxidos hidratados en este medio, facilitando los procesos posteriores de recuperación de metales. Asímismo, se evita la etapa de extracción por solventes, obteniéndose de ese modo un precipitado metálico o de electrodeposición directa desde las soluciones de lixiviación final. En ese sentido, la extracción y recuperación a partir de minerales complejos con altos contenidos de carbonatos mezclados íntimamente con sulfuros secundarios en condiciones normales es la alternativa técnica económica viable.

Dec 1, 2012

By A. Zorkovská, S. Castro, P. Baláž, Z. Bujnáková

Enargite (Cu3AsS4) belongs among refractory copper minerals with very low hydrometallurgical extractability of copper. An application of enargite leaching in acid solutions leads to simultaneous dissolution of copper and arsenic and the final leach solutions have to be treated for the separation of both elements. However, the alkaline leaching of enargite is selective. Arsenic passes into leach while produced copper sulphide represents the raw material suitable for pyrometallurgy. The hydrometallurgical processing of mineral can be influenced positively by mechanochemical route. We have shown that more than 80 % of arsenic can be extracted from enargite concentrate by atmospheric alkaline leaching at 95 °C when mechanical activation in an attritor is applied. The produced Cu2S can be further treated with elemental iron where mechanochemical intervention is applied in the second stage of enargite processing. The final product forms Cu/FeS nanocomposite from which copper nanoparticles can be easily separated. The illustrated concept of copper obtaining from copper sulphide is an example of so-called “dry” processing, as reactions in gas and liquid phases are excluded. This concept of environmentally friendly metallurgical processing can be classified as an impetus for novel technology to produce copper from enargite concentrates.

Jan 1, 2012