Search Documents

By Hamid Maleki

A comprehensive study consisting of stress determinations, core logging, laboratory testing, and numerical analyses was conducted to investigate the cause and potential alternatives to the coal bump conditions that developed in the Second North Panel of the Little Dove mine near Buntington, Utah. Roof rock characteristics were such that a cave did not develop above this 420 ft wide panel. After 700 ft of pillar retreat, severe coal bump conditions developed during pillar mining. The coal bump conditions resulted from excessive pillar stress which was caused by load transfer from the extracted, noncaving, portion of the panel. Site specific data and numerical modeling techniques were used to back-analyze the bump prone condition. This back- analysis lead to the identification of critical stress, closure, and energy release levels. These critical levels were then used to evaluate alternative pillar mining sequences in the hope that the potential for coal bumps could be reduced. It was found that while alternative sequences offered some potential improvement over the pillar mining sequence used in the mine, alternative pillar mining sequences would not significantly reduce the potential for bumps. For the roof characteristics at this mine, coal bumps are best avoided by developing narrow panels or significantly wider panels, which incorporate properly sized barrier pillars. Narrow panels, on the order of 300 ft, would not cave, but panel pillar stresses and the potential for umps would be moderated by the reduced r' panel width. Wider panels, of approximately 650 ft, would allow a cave to develop, also reducing panel pillar stresses and coal bump potential.

Jan 1, 1987

Copper, zinc, lead, and silver in the discordant magmatic-hydrothermal orebody of the Conrad Mine, N.S.W., all have a relatively high mean abundance. Any single concordant sulphide orebody containing the same metals has a similar order of mean abundance of only one or two of these, particularly copper, copper and zinc, or zinc and lead.The relative abundances of the metals in the Conrad orebody vary more widely than in concordant orebodies, and the lead-zinc-silver and copper-zinc-lead relationships are significantly different.INTRODUCTIONIn previous investigations of metal abundances in sulphide ores, the basis of selection of the orebodies was their form, and to some extent their geological setting, rather than hypotheses concerning their origin. In all cases they were generally concordant with the bedding of the sedimentary or meta-sedimentary rocks enclosing them, and most occurred in volcanic-sedimentary sequences. Their mineralogies were simple, and they were copper, copper-zinc, zinc or lead-zinc rich in composition. Most were of the type ascribed by several authors to exhalative-sedimentary processes.In one of these investigations (Stanton, 1958), it was pointed out that since the metals in ores of this type showed similar abundance patterns and behaviour, it would clearly be of interest to examine, and to compare with them, orthomagmatic and vein types, unquestionably derived from their igneous rock associates.The present investigation is concerned with a single orebody, of clearly discordant type, and of indisputable hydrothermal origin. The abundance and behaviour of copper, zinc, lead, and silver have been determined and compared to similar data fOl!' the concordant type. Such a comparison tests the possibility that metal abundance patterns of base metal ores may be indicative of the mode of ore deposition.

Jan 1, 1963

By R. Altindag

Engineers and researchers need to estimate the mechanical properties of rocks from P-wave velocity. In previous studies, the researchers have investigated either the limited values or all the data belonging to sedimentary, igneous, and metamorphic rocks together in the same statistical analysis. In this study, the raw data pertaining to only sedimentary rocks was taken from previous studies and evaluated. For this purpose, a total of 97 samples of sedimentary rock types were subjected to statistical analysis. First, the relationships between P-wave velocity and physical-mechanical properties were investigated by simple regression analysis. All the data were then subjected to multi-regression analysis. Some empirical equations with high correlation coefficients were derived for rock engineers. The equations obtained from the analyses are compared with previous equations found in literature.

Jan 1, 2012

By Kadri Dagdelen

Design of the ultimate pit limit to direct long range mine planning has been a celebrated problem in the mining industry, and in mining academia, since 1965. Although many papers have been presented on this topic, even today, there is not a single solution technique which is widely accepted and considered universally best. Many philosophical differences exist among the pit planners concerning the use of different methods and it appears that resistance is very strong towards accepting other techniques if you are a believer in one. Whatever the case might be, the pit parameterization technique for the ultimate pit limit design is the latest and takes a different approach than its predecessors. There are already a number of papers which discuss the concepts involved (Francois-Bongarcon, 1976; 1978; 1980; 1981); however, the aim of this paper is to fill in some of the gaps which are thought to be missing in the previous discussions and, in addition, to present the recent research done on the subject at the Centre de Geostatistique de l?Ecole de Mines de Paris in Fontainbleau, France. This paper is divided into two parts. The first part will discuss practical aspects and interpretations of pit parameterization concepts with- out using mathematical or theoretical arguments; the reader who is interested in the theory should refer to Francois-Bongarcon (1978). The second part will present an approach to obtain a complete double parameterization of reserves using an inexpensive (computer costs) single parameterization algorithm. A case study of this approach is also included.

Jan 1, 1982

By Mike Neill, O&apos

? Bypass soft soils near the surface ? Resist uplift loads ? Resist lateral loads ? Bypass scourable soils ? Bypass liquefyable soils ? Mitigate movement of expansive or frozen soils ? "Tune" foundations for vibrating machinery

Jan 1, 1998

A three?stages countercurrent fluidized bed prototipe reactor to neutralize the SO2from smelter gases has been developed. For gases with 8 vol-%SO2, at 800°C and for 4 h mean reaction time of the limestone, the capture of SO2 is 99%, with off gases with 0.07 vol-%. For 2 vol-%SO2, the total capture of SO2 can be obtained at 750°C and 4 h reaction time. The calcine obtained contain a blend of unreacted limestone and calcium sulphatewith minor amounts of residual lime.

Jan 1, 2006

Gold was determined directly in eight different mill cyanide solutions, by atomic absorption spectroscopy in an acetylene-air flame. Some of the mill solutions were diluted with water to bring them into the most sensitive absorption region (5-50 p.p.m. Au) whereas those solutions with very low gold content «2 p.p.m.) were concentrated by evaporation.Calcium was complexed with ethylene diamine tetra-acetic acid (EDTA) to avoid the undesirable effect of a precipitate on atomization.When added to standard gold solutions, EDTA had no effect on absorption, nor did any of the impurities common in mill cyanide solutions.Known amounts of gold, ranging from 2 to 30 p.p.m., were added to mill solution'aliquots and recovered to within 100 ± 2·5 per cent. For duplicate determinations under normal worKing conditions, standard deviation was 1·32 p.p.m.Excellent agreement was found between atomic absorption gold values and accurate fire assay values.INTRODUCTIONAtomic absorption spectroscopy has been shown to offer a rapid and accurate method for the determination of trace amounts of a number of metal ions. In the field of primary metallurgy atomic adsorption has been used for routine determinations of lead, copper, silver, zinc, cadmium and iron in a variety of raw materials and intermediate products.The scope of atomic absorption spectroscopy was reviewed recently by Willis (1963).The noble metals silver, gold, platinum, rhodium and palladium were determined by atomic absorption from chloride solutions by Lockyer ·and Hames (1959). In their determination of gold down to 1 p.p.m., they found no interference from the noble metals, nor from considerable excess...

Jan 1, 1964

By Gloria Fernández

La contaminación por drenaje ácido de mina se considera como la responsabilidad ambiental y económica más grande que actualmente enfrenta la industria minera. En ese sentido, se delimita las áreas afectadas mediante la perforación de pozos de monitoreo a través de un estudio geofísico previo. Por ello, el presente trabajo señala los métodos geofísicos como herramientas que pueden ayudar a delimitar y mapear las zonas afectadas por la contaminación proveniente de drenaje y filtraciones que va desde canchas de relave, pilas de lixiviación a minas abandonadas, etc.

Aug 25, 2002

The work described herein is the opening phase of an extensive system of underground excavation undertaken under contract with a Malayan authority.The specifications called for the lining of all tunnels in earth or broken rock with circular segmented cast iron lining, similar to that of the London tubes, and it is the installation of these linings which it is proposed to discuss.Owing to the long deferred delivery quoted and the obvious need for speed of access to the internal installation, it was decided to defer driving the completed circular section and substitute two small timbered headings.These could later be opened out in turn to full section and lined without prejudice to traffic, since both of them had access to the internal workings.NATURE OF ROCKThe rock series through which the circular sections were driven consisted of:(a) A wide zone of intrusive porphyritic granite, consisting generally of orthoclase phenocrysts in a ground mass of micro pegmatite. This area showed advanced weathering, varying from a stage showing slightly tinted kaolin containing approximately 20% of small boulders to one of ultimate decomposition to pure kaolin;(b) A narrow zone of weathered augite diorite, consisting of rock masses of a maximum weight of some 100-150 tons, isolated by clay seams up to 1 ft. 6 in. in width.The whole area was in a state of quasi-hydrostatic equilibrium, which resulted in heavy pressure immediately after excavation. Freshly broken faces would appear to be quite solid but, within a few minutes, would commence to sweat and "slab off" under pressure and, unless support was placed promptly, the whole face would burst out and run from above. Mucking was slow, owing to the plastic nature of the clay and the ease with which it puddled into slurry.In zone (b) a good deal of trouble was experienced because of the fact that the somewhat heavy blasting necessary tended to cause movement of the large rock masses. Subsequent scouring out of the supporting clay bands by the waterflow permitted settlement of the ground on to the timbers and many reinforcing sets were therefore required.The timbering of the pilot headings and its relation to the cross-section of the circular tunnels is shown in Fig. 1. Top and side spiling was driven in the ordinary way, but in bad ground intermediate sets and breast boards had to be placed. These sets were usually withdrawn after the...

Jan 1, 1941

By Edward A. Metz, R. Larry Grayson, Douglas F. Scott

We describe inconsistencies in disease and illness reporting in U.S. mining, identify under-reporting of disease and illness in U.S. mining, and summarize selected disease and illness in U.S. mining from 1983 through 2001. Methods: We summarized information on mining-related disease and illness data for the years 1983-2001 from the Mining Safety and Health Administration database (MSHA). Results: Discrepancies exist in types of information collected by the Centers for Disease and Control, the National Institute for Occupational Safety and Health, and the Mining Safety and Health Admin¬istration database. Several factors, including a worker's fear of losing his or her job, health insurance, or other job-related benefits contribute to under-reporting of disease and illness information in the US mining industry. Conclusions: Since 1997, both number of workers employed in mining and disease and illness rates have decreased; however, the highest disease and illness rates in mining continue to be coal worker's pneumoconiosis and hearing loss.

By M. du Plessis

This paper describes the evaluation of a limit equilibrium model to simulate the behaviour of crush pillars in platinum mines. An analytical model was derived to calculate the residual average pillar stress (APS) values of the crush pillars. The values predicted by this model were compared to the numerical values obtained from TEXAN simulations. In general, the limit equilibrium model appears to be very attractive for simulating pillar failure as the gradual crushing of the outside of the pillar and the transfer of stress to the intact core can be replicated. The value of the TEXAN crush pillar model was further demonstrated by simulating an idealized layout with crush pillars between two adjacent panels. The simulations illustrated that oversized pillars will not crush close to the face and this may lead to seismic failure in the back area. An important finding of the study is that closure measurements may prove to be a very valuable diagnostic measure in crush pillars layouts. Distinct differences in magnitudes of closure were simulated for a scenario where the pillars crush as expected, compared to the scenario where an oversized pillar is left. Experimental closure data collected in a crush pillar stope provided further evidence regarding the value of closure measurements in these layouts.

Jan 1, 2011

By Stanley Lefond

The health of the industrial minerals industry appears to be improving year by year. In fact, preliminary information suggests that only three commodities (asbestos, bromine, and sulfur-other) failed to show a production gain in 1984 over 1983. In 1983, 10 commodities failed to post gains and six remained constant. The total value of industrial mineral production in 1984 was $16.7 billion, up $1.4 billion from 1983. Cement, clays, gypsum, and crushed stone production increased. Since these are used in housing and construction, this suggests these industries are moving out of their recent doldrums. Barite and clay production also improved in 1984. Local US barite production, however, still has a long way to go to attain the 1981 high of 2.6 Mt (2.9 million st). Barite imports remain high. But they are not as high as the 1982 importation of 2 Mt (2.3 million st). Bentonite production in 1984 increased 20% in volume and 25% in value over the previous year. This suggests improvement in the drilling industry and an increase in demand for iron ore pelletizing grades. All in all, the industrial mineral industry is alive and well. And it shows signs of great improvement in the next few years. Many thanks to those industrial mineral technical committee members for their assistance in assembling this industrial minerals review: M. F. Dibble, H. W. Allen, G. H. Gallup, S. G. Ampian, D. W. L. Spry, H. G. Fleshman, and L. J. Czel.

Jan 5, 1985

By Maurice Hunter

The paper outlines recent design developments in the computerization of surface crawler drills for the quarry industry. It references the technology firstly developed for the underground mining and construction industry, where automation and computerization has been in demand for a number of years.

Jan 1, 2003

By Murillo Romero da Silva

Ligas com memória de forma (LMFs) são ligas metálicas capazes de recuperar o seu formato e tamanho original após deformação plástica quando aquecidas acima de uma temperatura crítica. Diversos casos de possíveis aplicações paras as LMF têm sido justificados no campo científico, com alguns poucos casos identificados para aplicação em massa, existindo uma ausência na literatura de uma análise crítica da aplicabilidade das mesmas que leve em consideração aspectos industriais e de mercado. Dessa forma, se faz necessário um estudo mais aprofundado que correlacione as ideias científicas geradas com a produção industrial e com a comercialização de LMFs. Nesse contexto, o trabalho visa através de levantamento e análise de patentes e artigos científicos, assim como por contatos industriais, estabelecer uma relação entre o desenvolvimento científico e o comercial das LMFs. Mais de 11 mil artigos e mais de 7 mil patentes foram produzidos nos últimos 16 anos, sendo observado uma tendência crescente da criação de conhecimento de LMF, o qual já vem sendo aplicado na indústria, justificando assim os esforços observados no campo científico. A área biomédica se destaca como a mais bem estabelecida no campo das LMF, com destaque para a utilização das ligas a base de NiTi.

Aug 17, 2017

By W. W. Krech, T. E. Perkins

As fractures are propagated through rocks, energy is absorbed near the extending crack tip. Apparent surface energies for several rocks have been measured by cleavage under dynamic con-ditions. At nominal crack velocities from 0.5 to 500 in (min, measurements showed that fractures propagated in discrete jumps. Calculated surface energies and moduli were relatively insensitive to nominal rate of cleavage. in another set of experiments, rocks were cleaved under high confining stresses. The rocks were submerged in low leak-off fluids which formed a filter cake on the freshly cleaved surfaces (similar to the hydraulic lracturing process). Apparent surface energies were increased substantially as the surrounding fluid pressure was increased. Moduli in bending increased significantly upon application of the first 1,000 psi but were insensitive to stress level at greater pressures. INTRODUCTION For almost 20 years, hydraulic fracturing processes have been utilized effectively to stimulate oil and gas wells. During this period, some process improvements have resulted from studies of fracture orientation, mechanics of fracturing, areas generated, conductivities of cracks, etc. Yet many questions remain concerning the conditions and pressures needed during fracture propagation. In this paper we will report additional studies of the mechanics of fracture extension. It was shown previously3 that large rock samples could be cleaved under controlled conditions so as to measure the apparent surface energy (that amount of energy absorbed per unit area of new surface created). In this paper we consider the effects of two additional factors on surface energies, viz.: (1) effect of cleavage rate and (2) effect of confining stress level. THEORY Cleavage experiments were conducted on rock samples similar to that illustrated in Fig. 1. Blocks of rock several inches wide, 2- to 3-in. thick, and up to 3 ft in length were grooved longitudinally with shallow guide slots. A crack was initiated and allowed to extend along the web as the top of the rock specimen was pulled (or pushed) apart. Auxiliary equipment permits the measurement of (1) force applied at the top, (2) separation at the top and (3) crack length. (Further experimental details will be given in the next section.) The rock beams created by the crack are considered ton be cantilever beams. The deflection (or separation of the rock beams) at any point is calculated 4,5 by the beam Eq. 1.

Jan 1, 1967

By D. Kwietnewski

With all of the unknowns associated with tunnel construction, how does a contractor choose a roadheader? This paper presents a review of several models of roadheaders being used in today?s tunnel projects. The features of different models of roadheaders are presented and compared. Roadheader size and cutter power generally determine which roadheader is best for a particular job. We will also present a model for matching features of the roadheader to the anticipated ground conditions such that the most efficient machine is selected for the project.

Jan 1, 2011

Satellite Image Based Strategies to Evaluate the Impact of Dismissed Mine Site - An Application to the Mae Moh Coal Mine Area in the Lampang Province, Thailand

Sep 13, 2010

By A. K. Majumder

The multi-gravity separator (MGS) is a novel piece of equipment for the separation of fine and ultra-fine minerals. However, the published literature does not demonstrate its use in the separation of coal fines. Therefore, an attempt was made to study the effects of different process variables on the performance of an MGS for the beneficiation of coal fines. The results obtained from this study revealed that among the parameters studied, drum rotation and feed solids concentration play dominating roles in controlling the yield and ash content of the clean coal. Mathematical modeling equations that correlate the variables studied and the yield and ash contents of the clean coal were developed to predict the performance of an MGS under different operating and design conditions. The entire exercise revealed that the MGS could produce a clean coal with an ash content of 14.67% and a yield of 71.23% from a feed coal having an ash content of 24.61%.

Jan 1, 2007

By Zhenqi Cai

The ongoing Overpeck Valley Parallel Sewer Project of Bergen County Utilities Authority (BCUA), New Jersey, is a US $65 million CSO improvement program to meet a State DEP consent order by 2010. One major program component includes a total of 1.8 km (1.2 mile) long, 1,800 mm (72 in) diameter reinforced concrete pipe (RCP) installed by a Herrenknecht AVND1800AB MTBM. The alignment includes drives through 850 m (2,788 ft) of extremely soft glaciolacustrine varved clay, 980 m (3,214 ft) of loose to medium dense mixed soils containing silty sands, gravels, and boulders, and crosses under the New Jersey Turnpike, US Highway Route 46, and a CSX Railroad Intermodal Yard and a branch mainline. Two types of MTBM cutterheads are being used, one configured for the weak varved clay, and one for the mixed soil conditions. The MTBM is also equipped with a double-steering system consisting of a standard front steering joint and a second trailing steering joint to assist grade control should adequate steering not be achieved by the front primary steering in extremely weak soil conditions. This paper discusses the significant engineering aspects and challenges related to site settings, ground characterization, key MTBM features and performance, and required ground treatment.

By Michael W. Lewis

The latest downturn in the world’s metal prices has forced many mining companies to focus on cost reduction and productivity improvements to remain competitive. Maintenance represents a significant part of the overall operating costs in the mining industry. A structured, proactive maintenance approach, such as reliability-centered maintenance, can achieve cost reductions and productivity improvements. Remote condition-monitoring systems are becoming commonplace because they have the potential to identify problems before failure. Detection of equipment degradation before failure will enable repairs to be scheduled, thereby reducing costs and interruptions to production. The mining industry is in the midst of uncertain times. Decreasing commodity prices, demand, head grade and capital availability along with increasing environmental requirements have put pressure on mining companies to significantly reduce costs to maintain short- and long-term viability. Corporations are looking at expansion, merger/consolidation and financial/hedging programs to achieve these cost reductions. Mines are reducing costs by eliminating all but essential expenditures, increasing production levels, reducing overtime and investing in new technologies.

Jan 1, 2000