Search Documents

By M. Rafieazad, P. Fathi, M. Mohammadi, A. M. Nasiri

This study examines the impact of low-temperature heat-treatment cycles on microstructure and corrosion performance of Direct Metal Laser Sintered (DMLS) AlSi10Mg_200C alloy. It is known that the morphology and the size of eutectic silicon are the two most critical factors affecting mechanical properties of the AlSi10Mg alloy. Although high-temperature heat-treatment cycles are common practice for the strengthening of the cast Al-Si-Mg alloys, in the case of DMLS fabricated AlSi10Mg alloy, high-temperature solutionizing and low temperature annealing cycles result in mechanical properties degradation primarily due to a dramatic decrease in the solubility of Si in the super-saturated a-Al matrix of the as-printed alloy. In this study, low-temperature heat-treatment cycles that only promote precipitation of Mg2Si accompanied by the interruption of the silicon network were investigated. SEM and XRD analysis were utilized to observe the evolution of microstructure after different annealing heat-treatments at 200, 250, 300, and 350°C for 3 h. Increasing the heat-treatment temperature contributed to the Si networks interruption and an increased precipitation of Mg2Si phase. Low-temperature annealing from 200 to 350°C was found to promote the homogeneity of the microstructure characterized by a uniform distribution of eutectic Si in ??-Al matrix. Additionally, in order to investigate the impact of different heat-treatment cycles on corrosion resistivity of DMLS-AlSi10Mg_200C, the potentiodynamic polarization testing and electrochemical impedance spectroscopy were performed in a 3.5 wt.% NaCl solution. The results revealed more uniformly distributed pitting attack on the corroded surface by further increase in the annealing temperature, which was attributed to the uniformity of Si dispersion. In comparison, low temperature annealing at 200°C led to a penetrating selective corrosion attack along the melt pool boundaries, resulting in a higher corrosion rate associated with the lower absolute value of impedance of the protective passive film on the surface.

Jan 1, 2018

By Lucas L. da Costa, Sergio N. Monteiro, Romulo L. Loiola, Tammy G. Rodrigues Portela

"The fibers extracted from the petiole of the buriti palm tree are relatively strong as compared to other lignocelluloses fibers, with a potential for composite reinforcement. In this work, polyester matrix composites incorporated with these fibers were investigated for their flexural behavior. Specimens with up to 40% in volume of continuous and aligned buriti petiole fibers were bendtested until rupture. The results showed an increase in both the composite mechanical strength and the stiffness with incorporation of these fibers. A fractograph analysis by SEM disclosed a moderate adhesion mechanism between the buriti petiole fiber and the polyester matrix. This mechanism is apparently responsible for the improved performance of the composites.IntroductionIn recent years, the substitution of energy-intensive synthetic materials for natural ones is being considered in many industrial sectors including automobile, packing and textile [1]. A typical case is that of natural fibers, mainly those obtained from cellulose-based plants also known as lignocelluloses fibers. They have being investigated in the past two decades, aiming to replace synthetic fibers, particularly the glass fiber, commonly used as polymer composite reinforcement [2-8]. From the engineering point of view, lignocellulosic fibers present today important environmental, economical, societal and technological advantages already discussed [7-8]. Moreover, several lignocellulosic fibers are known since the beginning of our civilization and still cultivated or naturally extracted all over temperate and tropical regions of the world. According to Kalia et al [1 ], these fibers can be classified by their origin, as shown in Table 1."

Jan 1, 2011

By Arthur F. Taggart

Tins paper proposes two units (believed to be new) for designating, respectively, capacity and efficiency for primary and intermediate crushers. CAPACITY Operators know that the tonnage of rock that can be put through a particular crusher in a give time depends primarily upon the crusher setting (open setting for jaw and primary gyratory types; closed setting for cones and rolls), and secondarily on the lithological character of the feed, its maximum size, the amount of fines that it carries, its moisture content, and the method of feeding. The proposed capacity formula states a relationship between all of these factors in one empirical equation, as follows: TR = TR80KK'K" [I] in which Ts, called "reduction tons per hour" is the new capacity unit; T = tons of feed per hour requiring crushing; R80 = "80-per cent reduction ratio"; and K, K', and K" are constants that approximate quantitatively lithological character, moisture content and method of feeding, respectively. T is the hourly weight of material in the feed that is coarser than the coarsest discharge of the crusher. (For marked departures from the normal specific gravity range - 2.5 to 2.7 - T should. be adjusted to corresponding volumes.) In the crushers under consideration, discharge from the crushing zone is limited by the minimum dimension of a particle. Passage of the particle through a square-mesh screen is limited by its intermediate dimension. Sheppard1 has shown that the ratio of maximum: intermediate: minimum average dimensions of broken rock fragments may be taken as about 1.5 : 1 : 0.6 for nonslabby rocks such as are normally crushed, while for slabby rocks, such as thin-bedded sedimentaries, foliated schists and gneisses, and the blocky metamorphics, the ratio is of the average order I.3:I:0.3, with the possibility of an even smaller relative value for the thickness. Gaudin2 finds the corresponding ratio for 150 + 200-mesh pyrite to be 1.4: 1 : 0.6. The hourly tonnage of crusher-plant feed, therefore, should be diminished by the amount thereof that would pass a square-mesh screen of which the aperture is S times the crusher setting, where S is a shape factor with the value 1.7 for rocks that break exceptionally cubic; 2 for ores and rocks that exhibit no appreciable tendency to slabbiness; and 2.5 to 3, or, in exceptional cases, even larger, when the tendency to slabbiness is marked. R80 is the quotient of the theoretical square-mesh aperture that would pass 80 per cent of the feed, divided by the aperture that would pass 80 per cent of the product. It is best determined from screen tests.

Jan 1, 1941

By Raymond L. Carpenter

The thermal conductivity, electrical resistivity, and Seebeck coefficient for nine compounds, based on the formula for enargite Cu3AsS3, were measured in a search for efficient materials to be used in thermoelectric generators or refrigerators. Results indicate that one of these compounds, Cu3SbSe4, has thermoelectric properties approaching those of bismuth telluride. An investigation of the effect of adding small quantities of tellurium to Cu3SbSe4 and Cu3SbS4 in order to improve their properties also was made. A figure of merit of 2.1 x 10-4 °C-1 was obtained for Cu3SbSe4 + 0.1 percent tellurium.

Jan 1, 1963

By James D. Hall

THIS essay deals with the materials and methods used in the waste filling of scopes in Canadian mines, with especial reference co the methods used at the Sullivan mine, Kimberley, B.C. The author would like to thank members of the staff of the Sullivan mine for information obtained, and acknowledges material from the following publications: Waste Filling of Stopes: Information Circular 6816, U.S. Bureau of Mines. Mining Methods and Practices at Lake Shore, by Leslie S. Weldon; Trans., C.I.M. & M., Vol. XXXIX, 1936, pp. 142-202. Development and Mining (at the Mcintyre Mine), by D. E. Keeley; Eng. & Min. Journal, November, 1933. INTRODUCTION Although mining in Canada is a relatively youthful industry, many of our mines have reached a stage of extraction which requires waste filling, both as a means of support and co make possible the winning of ore that would otherwise have co be left in the mine. Fill may be used at regular intervals as one of the cycle of operations, as in cur-and-fill and square-set scoping; or it may be introduced into a completed stope co provide permanent support for overlying rock formations, and co permit mining of pillars of valuable ore. Waste fill is sorted in resuing, which is a form of cut-and-fill scoping employed in narrow veins.

Jan 1, 1937

By Euler De Souza

"Underground operation ventilation energy requirements constitute a significant portion of mine energy consumption (40–50%) and total energy costs (25–40%). In general, mine ventilation systems are energy inefficient; the author has found several systems that operate at efficiencies below 65%. This paper presents how engineering design principles can improve the performance and efficiency of ventilation appliances, resulting in reduced power consumption and operating costs. Case studies demonstrate that, by retrofitting ventilation appliances using proper engineering concepts, systems will operate at efficiencies well above common operating efficiencies, resulting in a drastic reduction in costs and base electrical and energy loads.RÉSUMÉ Les besoins énergétiques nécessaires à l’aérage d’une exploitation souterraine représentent une part considérable de la consommation d’énergie d’une mine (de 40 à 50 %) ainsi que des coûts totaux liés à l’énergie (de 25 à 40 %). De manière générale, les systèmes d’aérage d’une mine sont loin d’être écoénergétiques ; l’auteur a trouvé plusieurs systèmes fonctionnant à des rendements inférieurs à 65 %. Cet article présente les principes de conception technique qui peuvent améliorer la performance et l’efficacité des systèmes d’aérage, entraînant une réduction de la consommation d’électricité et des coûts d’exploitation. Des études de cas montrent qu’en les rénovant à l’aide de concepts techniques adéquats, les systèmes d’aérage fonctionneront à des rendements bien supérieurs aux rendements habituels d’une exploitation. Ces rénovations donneront lieu à une réduction considérable des coûts ainsi que des charges électriques et énergétiques de base.INTRODUCTIONIncreasing electricity supply problems in North America have encouraged an industry-wide evaluation of energy consumption, resulting in a more urgent emphasis on energy-efficient design and operation for all energy-consuming systems. Electricity is the main mode of energy supply and the mining industry is affected by the increasing cost of this commodity (Natural Resources Canada, 2017). Ventilation systems normally operate 24 hours per day, 365 days per year, and account for 25–40% of the total energy costs and 40–50% of the electrical consumption of a mine operation (De Souza, 2013). Ventilation engineers are under ever-increasing pressure to reduce ventilation energy consumption and be cost effective."

Jan 1, 2018

By L. D. Clark, S. S. Saluja

A physical law, governing the rupture of rock by confined explosive charge correspondent to current expressions for determining weight of charge to rupture rock burden, W, was developed in the form Q = cVw3 by two early investigators performing unique experiments with ice. The coefficient C, is found by trial blast. Recent physical tests conducted with rock, synthetic materials and ice to establish the validity of the theory on which it and other related formulae are based indicated: (a) that failure under hydrodynamic impact pressure is by tension rather than shear as was assumed; (b) that the fundamental law of mechanics, enabling the determination of Q = cvw3, modified to the form P = R x Sa x Wb is valid when low velocity explosives are used; (c) that rock breakage under the action of low velocity explosives is entirely due to explosion gas pressure, as was believed; (d) that under the action of high velocity explosive it is due to the joint effects of scabbing and gas pressure; and that further possible modification could make the above equation also applicable to these joint mechanisms. shape could be easily frozen and because large loads would not be required. They found: (a) that the not unfamiliar shearing equation for metals was applicable to ice where P = load in lb; S = periphery of pressure surface, in.; W = burden, in.; K = modulus of rupture by shear in lb per in.2; and (b) that "the form of cavity produced by the application of gradual pressure is similar to that obtained by blasting in rock under similar conditions of free face and pressure surface!" This similarity in crater shapes leads to the conclusion that rock would rupture by shear, as did ice, and its behavior under the force of a blast could be governed by such a relationship as P = S x W x K. Three important interrelated empirical expressions were derived and rock, charging and spacing coefficients C,, C, and e were established and substantiated by trial blasts. In checking the accuracy of the main assumptions, duplication of the ice tests, substituting rock, suggested that K is not constant and that P = K x W x S, though valid for ice, does not necessarily hold for homogeneous limestone.' Conclusions from this later work raised questions making continued investigation desirable because such conclusions do not destroy the practical value of the empirical equations or theory. Further study for the establishment of the relationship between load, burden and periphery of the pressure surface and possible application of these to the mechanism of rock blasting was undertaken by the authors of this paper. MECHANICAL TESTING - EXPERIMENTAL PROCEDURE Certain inconsistencies in the results of the aforementioned tests repeated on three types of limestone suggested these inconsistencies be attributed to rock inhomogeneity. It was also suspected that the loading speed, which could not be held uniform, may have contributed. The earlier work with both rock and ice

Jan 1, 1964

By A. L. W. Lips, B. P. J. Stevens, T. J. R. Bareley, E. Rothery, S. H. White

B.P.J. Stevens contributes a further response to the authors' earlier lengthy reply regarding their paper published in Trans.IMM B, vol.104, 1995, p.B1-B17, contending that despite the positive contribution clarifying their interpretations they perpetrate some misquotations, attempt to rewrite history and fail to understand the New South Wales Geological Survey's stratigraphic interpretation of the Broken Hill area. The paper's authors, in their further response, robustly defend their views, insisting that Stevens tends to misquote or take out of context what they have written and reiterating their findings that Zn is tectonically stacked above Pb at the north end of the orebody, that the written development of the stratigraphic interpretation is as they have stated, that shearing has attenuated or removed fold limbs in the Broken Hill block and that the 1:100 000 stratigraphic map reveals that magnetic anomalies are oblique to and truncated by the Geological Survey's interpreted stratigraphic boundaries

Jun 19, 1905

By Jennifer S. Riefenberg

The U.S. Bureau of Mines conducts basic and applied research related to predicting, eliminating, and/or controlling rock bursts in underground hard-rock mines and coal bumps in underground coal mines. An important element in this research is the development of a reliable and efficient microseismic source location technique. This report presents the results of a Bureau study to develop and evaluate a new algorithm to locate microseismic events based on the Simplex method, a powerful linear programming technique. The technique was tested on both field data and simulated data. Microseismic event source locations obtained with this new Simplex-based algorithm were shown to have less error than those locations obtained using a least squares method. It was concluded that the Simplex approach to source location of microseismic events can be used effectively in microseismic monitoring.

Jan 1, 1989

By R H. Knight

Uncertainty in prediction and modelling of geological (physical) ore continuity in geometrically complex ore deposits is a key risk factor in mining. Reducing geometric uncertainty of hard-boundary ore/waste contacts and related geological features improves the efficiency of local mineral resource estimation and reserve calculation, mine/stope planning, ore control and in-mine exploration. Detailed underground mapping of serial-level drives provides a continuous record of the characteristics and contact configuration of ore, as well as crucial ore-related geological features that are required to resolve geometrical variability when closely spaced drilling proves inadequate or is cost-prohibitive. The mapping-based approach described in this paper re-establishes the focus on the geology of the orebody by incorporating high-value, detailed geologic mine mapping information. Mapped ore-related configurations and relationships, recorded on a succession of faces or on a series of levels, provide the basis for 3D interpolation and extrapolation of the local geologic continuity of an orebody. Correlative points representing locations of key ore-related geologic features on each face or level are linked by 3D polylines or trajectories forming a coherent geometrical framework. The coherent progression of geometric changes mapped by these trajectories reveals the overall ‘dynamic’ of the geometrical framework, as well as the spatial tendencies of its geological constituents. Distinct sets of ore control trajectories are selected from within the framework and are used in the construction of alternative geological ore continuity models. As mining proceeds, alternative models are evaluated, and are then either refined or rejected. The geometrical framework is used to evaluate theoretical models and practical heuristics, focus exploration targeting and inform and guide all aspects of mine geology in active mines. This approach also lends itself to analysis of global ore continuity in the re-evaluation of mature or abandoned mines. Its use is particularly effective in geometrically complex orebodies such as the West Branch orebody and the orebodies of No 2 mine of the Balmat-Edwards-Pierrepont zinc district, which are used to illustrate the method. CITATION:Knight, R H, 2014. A mapping-based approach to geological continuity prediction using examples from the Balmat-Edwards-Pierrepont Zinc District, St Lawrence County, New York, USA, in Proceedings Ninth International Mining Geology Conference 2014 , pp 65–76 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 18, 2014

By Susanna G. de Jager, Francis W. Petersen

"The aim of the project was to develop a methodology applicable to different South African coal types to be able to predict with a high degree of certainty what kind of reagent will be suitable for flotation of a certain coal type.The study included 5 coal samples from different collieries and included Highveld seam 3 and 4 coal (as one sample), Waterberg coal (zone 10 -11), Highveld seam 5 upper coal and Witbank seam 2 and seam 4 coal. Seam 3 and 4 (mixture) coal, Waterberg and the seam 5 upper coal were all found to be vitrinite rich coals. The coal characterisation study included petrographic analysis, proximate analysis, float-sink analysis, oxygen-containing functional groups, surface extraction, flotation release analysis and contact angle measurements.The flotation tests showed that the best reagents to float all of the coal samples studied are iso-decanol and dodecene. These reagents produced flotation products that are near to the release curve. Statistical relationship for predicting ash content and yield that can be expected for a certain coal type and selected collector was obtained. From the relationship, the accuracy of the yield is above 95% (p-value below 0.05) with a linear regression of 0.9289. The accuracy of the ash is slightly lower with a linear regression of 0.7841 but also above 95%."

Jan 1, 2003

An Attractive Investment ?Near term low cost and secure PGM producer ?restricted supply legislated demand ?strong pipeline of resource development ?Building Canada?s largest undeveloped PGM-Cu resource ?All work (resource, reserves, DFS, EA) is NI43-101 compliant ?Strong balance sheet: over $8 m in cash with no debt

May 1, 2010

By E. Van Der Lingen, A. Paton

"The South African ferrochrome industry has been faced with various challenges during the past few years, such as influences from the market, manpower strikes, China’s control over the demand for both ferrochrome and chrome ore from South Africa, and electricity supply constraints, placing increased pressure on the local industry to improve output in order to remain globally competitive. The year 2016 brought a dramatic change in the local ferrochrome industry, being marked by higher chrome ore prices and the takeover of some idle smelters.This study investigates the methods of technology acquisition used in various parts of the ferrochrome smelter value chain throughout a business cycle, and whether there is a preference for a specific acquisition in an explicit part of the value chain. The study also considers whether companies prefer to partner with local or global institutions for collaborative development, and the methods used by companies to protect their technologies.IntroductionSouth Africa holds the world’s largest chrome ore reserves and was the world’s largest producer of ferrochrome until 2012, when China became the leading ferrochromeproducing country. South Africa’s chrome ore (chromite) supply into the Chinese market has risen significantly from 36% of China’s total chrome ore imports in 2010 to more than 70% in 2016 (Fowkes, 2014; Creamer, 2017). China controls the demand for both ferrochrome and chrome ore from South Africa (Fowkes, 2014). China’s high import rate of chrome ore has resulted in ferrochrome prices being driven down and a depressed ferrochrome market. The South African industry meets the chrome ore demands but loses out on ferrochrome beneficiation.Furthermore, the local ferrochrome industry has been threatened with the overall poor competitiveness over the past few years, resulting in four of the eight producers ceasing operations at the beginning of 2016. Challenges experienced by the producers, some of which are directly linked to production costs, include influences from the market, productivity that was affected by wildcat strikes, China’s control over the demand for both ferrochrome and chrome ore, and electricity supply issues (Fowkes, 2014, 2013; Biermann, Cromarty, and Dawson, 2012). Ferrochrome production is energy-intensive and South African producers have faced higher electricity costs, electricity supply complications, and a weaker currency exchange rate since 2009."

Oct 1, 2018

By C. Pichler, C. Benigni, J. Antrekowitsch

"The recycling of steel mill dust results in zinc oxides which are sold to the primary industry in or-der to recover zinc in its metallic form. Due to the contained impurities - chlorine and fluorine - these sec-ondary oxides are usually charged into the roaster together with primary concentrates. Appearing problems in this furnace limit the application of secondary materials. Based on the zinc amount, a direct leaching, assumed that a low halide concentration is present, would be possible. To use the zinc solution directly in the electrowinning stage, the concentration of impurities, first of all iron, is limited. Iron can be found in secondary zinc oxides due to carry over during the recycling process. In order to reduce the iron content in the solution, the leaching has to be pH-controlled. This leads to a limited number of simple purification steps before the solution enters the electrolysis. Various trials were performed to evaluate the influence of temperature, time and sulphuric acid concentration on the iron dissolution. This paper deals with the results and also focuses on other impurities such as halides. Additionally, the soda washing process, usually done with secondary zinc oxides to remove most of the halides, and the challenges within this step are discussed.INTRODUCTION Recycling of steel mill dust, which is the main zinc containing residue, in the Waelz process dis-plays the common method worldwide. The product of the process is a secondary zinc oxide which is con-taminated with different elements like lead, iron and halides due to mechanical carry over or evaporation. Depending on the feeding material the concentration of each element in the dust is varying. The zinc con-tent of the product, also called Waelz oxide, lies around 65–68%. Based on these values it presents an al-ternative to the primary concentrate for the production of metallic zinc. The contained halides limit the direct utilization in the leaching stage and therefore have to be reduced. State of the art is a soda washing process but also solvent extraction gives a possibility to remove chlorine and fluorine but the desired con-centration for the electrolysis is hardly reachable (Antrekowitsch et al., 2016) Iron is present as an undesirable component of such secondary zinc oxides due to carry over. During the hot acidic leaching of the secondary concentrate, iron is dissolved too. Based on the higher electrical potential iron has to be removed before the zinc solution enters the electrowinning stage. It is usually removed by precipitation as goethite, hematite or jarosite, which is the common precipitation residue (Ismael et al., 2003)."

Jan 1, 2017

By Fred C. Turin, Jasinder S. Jaspal, Alan G. Mayton, William J. Wiehagen

This report describes serious injuries occurring to bulldozer operators working at U.S. coal, metal, and nonmetal mines. The period covered is 1988-97. The data were collected by the Mine Safety and Health Administration (MSHA). A total of 873 injury records are examined. These injuries resulted in 18 fatalities and 31,866 lost workdays. All of these injuries occurred to dozer operators while they were doing common production tasks. An injury classification system was developed to code the narrative information that describes the circumstances surrounding the injuries. Injury records are categorized by activity (task being done), incident result (what apparently happened to the dozer), and operator impact (how the operator was injured). Where information is available, contributing factors are identified. This classification system supplemented the standard injury/illness data classification system compiled by MSHA. The results of the study indicate that, from 1993 to 1997, the number of serious injuries to dozer operators declined by 30%. The reduction in serious injuries was accompanied by a decrease in days lost due to injury. Although the number of reported injuries has decreased, dozer operators being jolted and jarred accounts for the largest percentage (70% of the incidents) and severity (75% of the workdays lost) of serious injuries while operating the equipment. Vertical jars (while backing up the dozer) resulting in injury to the operator accounted for a sizable percentage of jolting and jarring injuries. Working near an edge carries significant risk for fatal injuries. Of 116 incidents where the dozer fell over an edge, rolled over, or fell into a hidden void, 14 (12%) resulted in fatal injuries. In cases where the dozer operator either jumped or was thrown out of the cab in a fall over or rollover, 7 out of 26 were killed. Overall, 80% of the fatalities occurred while working near an edge or hidden void or on a steep slope. Further reductions in injury risk will require more widespread use of seatbelts, field and laboratory research interventions to better assess the effect of alternative engineering (e.g., seat and seat suspension) designs to dampen or isolate the effects of shock and vibration, and continued focus on hazard awareness, recognition, and response.

Jan 4, 2001

By Erika Moonin, Jim Nickerson, Marcus Jensen

"This paper will explain how the Contractor and Owner avoided a contractual dispute involving characterization, impacts, and final remedy for challenging ground conditions encountered during drill and blast excavation of the starter tunnel required for launch of the tunnel boring machine (TBM). During excavation more than 600 feet underground, the Contractor encountered a large complex fault zone subject to more than 14 bar of water pressure. Successive ground inflows from the fault complex over a six-month period presented significant technical and partnership challenges for the team and ultimately delayed the project by nearly one year. This paper will discuss how the Contractor, Owner, and their respective consultants worked together to address these challenges, make decisions, and ultimately move the project to successful completion. PROJECT BACKGROUND AND NEED Seven states of the western United States of America rely heavily on the Colorado River and its tributaries for their water supply. The primary source of water for the Colorado River is winter snow that falls in the mountains ringing the Colorado River basin, including the Rocky Mountains, the Wind River Mountains, and the Uinta Mountains. Flows in the Colorado River vary significantly from year to year, depending on the amount of snow and rain deposited in the basin. During the 1980s and 1990s, snowfall was relatively abundant and Colorado River flows were high on average. Beginning in the year 2000 and continuing to the present day, snowfall has been well below documented historical averages and Colorado River flows have diminished. In fact, a trend toward diminishing flows is evident during the period of the historical record. This variability in Colorado River flows and the trend to lower flows is represented in the following Figure 1."

Jan 1, 2016

By Jack L. Woodward

The evolution of surface mining equipment has resulted in larger, faster haulage units, loaders, etc., resulting in increased demands on steering technology. Careful analysis of these systems was warranted to determine if steering-related safety problems have been introduced. The objectives of this program were to: 1. Define the generic types of steering systems being used on mobile mining equipment used in surface mining operations. 2. Gather information on steering-related accidents in mining operations. 3. Assess the need for initiating government-sponsored research into steering system technology. A comprehensive literature survey was conducted concurrent with extensive contacts with mining operations, mining equipment manufacturers, steering system component manufacturers, and government agencies. A Technical Evaluation Group composed of representatives from the above organizations was formed to review the data gathered. It was concluded that the steering systems in use on surface mining equipment are reliable and do not present a safety problem. The Society of Automotive Engineers, Inc. is active in pre-paring voluntary consensus standards to assure that the minimum levels of performance are defined for industry.

Jan 1, 1979

A revolutionary development in blasting materials has occurred in recent years. Ammonium nitrate, sensitized by the addition of a small percentage of No. (class) 2 diesel fuel or other suitable petroleum product, has been adopted as a low-cost, efficient blasting agent2 in a wide variety of mining, quarrying, and heavy construction operations. Moreover, the ready availability of the component supplies throughout the Nation, together with the ease of formulating them into effective blasting agents, has made it possible for the blaster himself to prepare the mixes at the site of use. Recently, most established explosives manufacturers have begun supplying premixed AN-FO (ammonium nitrate-fuel oil) or a comparable product to various mining operations. However, many individuals and small business establishments are marketing premixed products prepared in facilities that are often poorly constructed and poorly located. Although these blasting agents have partly or wholly displaced explosives such as dynamites in many applications, there are some blasting operations in which the fuel-sensitized ammonium nitrate agents do not appear to be well adapted. As long as the hazards they present are clearly understood and respected, ammonium nitrate-based blasting agents have important safety characteristics when prepared under competent factory control or field-mixed under equivalent close control. This publication attempts to summarize the knowledge of those hazards and to incorporate practical ways to cope with them.

Jan 1, 1963

By S. Esfahani, M. Barati, Y. Kauwachi

"Heat recovery from slag has gained attention due to its high potential in lowering energy intensity of metal extraction processes. A direct method to recover the thermal energy of slag is to use countercurrent air flow that extracts the heat from falling droplets. Often, the solidified slag is aimed to be used as a substitute for Portland cement, thus high cooling rates are required to form an amorphous slag with sufficiently strong hydaulicity. Rapid cooling however involves using large gas flow rates that in turn lower the thermal efficiency of the process. This article presents a mathematical model that was developed to determine the optimum conditions in the heat recovery process and to investigate the effect of the air flow and granule diameter on the cooling rate of the droplets as well as the thermal efficiency of the heat recovery system. INTRODUCTIONMetallurgical slags are the largest by-product of high temperature materials refining and extraction processes. The total amount of metallurgical slag produced in the year 2008 has been estimated at up to 422 million tonnes containing up to 222 TWh/y (Barati and Esfahani, 2011) of thermal energy. Over the past four decades attempts have been made to recover this substantial amount of energy as heat, electricity, or fuel, while none of the proposed method has been commercialized yet.During slow cooling the slag tends to crystallize the constituents (CaO, SiO2, Al2O3, etc.) into a hard, heavy solid. In the past, over 90% (Bengt, 1983) of the molten waste was discharged onto heaps and allowed to cool slowly, then crushed and used in road construction or land filling or as coarse aggregate for concrete. However, later it was found if cooled rapidly, the slag can be used as a substitute for Portland cement. As a result, processes such as wet granulation were created in which molten slag is fragmented with water, forming amorphous (glassy) phases. Despite its effectiveness in producing a suitable material, heat would not be recovered through this process. Thus, dry granulation was introduced in 1930’s and was developed further in 1970 – 1980’s."

Jan 1, 2012

By L. Tong

Stirred milling of laterites offers possibilities for improving liberation and selective size reduction of soft nickel-bearing minerals in laterites. Batch grinding tests were performed in a Netzsch LME4 stirred mill on a siliceous goethitic (SG) nickel laterite sample (-2000 µm particle size) to evaluate the effect of operating conditions such as stirrer speed, grinding time, pH, solid content, water salinity and charge volume. The target was to produce a -38 µm fraction in the milling product with high nickel recovery and grade. Addition of dispersant (sodium hexametaphosphate) was also optimized with respect to the rheology of the slurry. In terms of stress intensity, the optimum grinding conditions for selective size reduction were: 1000 rpm, 50 per cent charge volume. At higher stress intensity (2000 rpm), Ni recovery in the -38 µm product was higher, but Ni grade was low, due to the breakage of the harder siliceous particles. Decreasing the yield stress by modifying slurry pH or adding dispersant improved the rheological properties of the pulp, but had no great influence on Ni upgrade in the fine product. Modifying water salinity by adding 2 M NaCl had also little effect. The breakage of the +38 µm particles in the feed determined Ni upgrade greatly. Ni grade in the -38 µm product decreased with grinding time, suggesting that the Ni-bearing minerals break first, while the harder siliceous minerals have a lower breakage rate. The breakage rates with respect to sample mass for Ni, Mg and Si indicate that: Mg > Ni > Mass > Si. The optimum grinding time for the highest Ni upgrade was 0.25 min. The Ni grade increased from 0.88 per cent to 1.35 per cent (upgrade 54 per cent), with 24 per cent Ni recovery. Keywords: fine grinding, stirred media mill, nickel laterite, slurry rheology

Sep 1, 2012