Search Documents

By Barnettm Ray R.

As a result of the Farmington explosion, the U. S. Bureau of Mines commissioned the National Academy of Engineering to a determine what steps could be taken in a short time frame to significantly reduce fatalities as a result of underground fire and explosion in coal mines. Three areas were named by the Academy as having the greatest potential; survival, communications, and rescue. The Bureau subsequently awarded a $3-5 million contract to the Special Systems Division of Westinghouse Electric Corporation for the development of prototype equipment and procedures. These were recently tested in a simulated emergency situation and will be delivered soon. Contractor recommendations for utilization and for further development effort will be studied and appropriate action taken.

Jan 1, 1971

By R. J. Matetic, J. Noll, C. Zhou, J. DuCarme, M. Reyes, J. Srednicki

"In April 2016, the U.S. Mine Safety and Health Administration (MSHA) began requiring the use of continuous personal dust monitors to monitor and measure respirable mine dust exposures to underground coal miners. Mines are currently using the PDM3700 personal dust monitor to comply with this regulation. After the PDM3700’s implementation, mine operators discovered that it interfered with proximity detection systems, thus exposing miners to potential striking and pinning hazards from continuous mining machines. Besides the PDM3700, other electronic devices were also previously reported to interfere with proximity detection systems. MSHA sought the aid of the U.S. National Institute for Occupational Safety and Health (NIOSH) and mining industry stakeholders to determine how the PDM3700 and some other electronic devices and proximity detection systems interact with each other. Accordingly, NIOSH investigated existing standards, developed test protocols, designed experiments and conducted laboratory evaluations. Some interferences were observed to be caused by electromagnetic interference from some electronic devices, including the PDM3700. Results showed that there was no significant interference when the PDM3700, as well as other electronic devices, and the miner-wearable component of the proximity detection system were separated by distances of 15 cm (6 in.) or greater. In the present study, it was found that the PDM3700 and the personal alarm device needed to be at least 15 cm (6 in.) apart in order for them to be used simultaneously and reduce potential interference. IntroductionUnderground coal miners are exposed on a daily basis to a variety of hazards, such as coal dust exposures, high noise levels, roof and rib falls, potential for fires and explosions, and operating and working with heavy machinery. One of the hazardous jobs is that of operating or working near a continuous mining machine. According to U.S. Mine Safety and Health Administration (MSHA) statistics, 44 miners had been fatally struck or pinned by a continuous mining machine since 1984. In an effort to prevent future striking and pinning fatalities from occurring, proximity detection systems have been developed and are required on all operating continuous mining machines in underground coal mines, with the exception of full-face continuous mining machines, by 2018 (MSHA, 2015a)."

Jan 5, 2018

By Thomas L. Vande Voort

The strategic plan for bridge engineering issued by AASHTO in 2005 identified extending the service life and optimizing structural systems of bridges in the United States as two grand challenges in bridge engineering, with the objective of producing safer bridges that have a minimum service life of 75 years and reduced maintenance cost. Material deterioration was identified as one of the primary challenges to achieving the objective of extended life. In substructural applications (e.g., deep foundations), construction materials such as timber, steel, and concrete are subjected to deterioration due to environmental impacts. Using innovative and new materials for foundation applications makes the AASHTO objective of 75 years service life achievable. Ultra High Performance Concrete (UHPC) with compressive strength of 26,000 psi (180 MPa) and excellent durability has been used in superstructural applications but not in geotechnical and substructural applications. This paper explores the possibility of using precast, prestressed UHPC piles in future bridges. An H-shaped UHPC section, which is 10-in. (250-mm) deep with weight similar to that of an HP10×57 steel pile, was designed for constructability and economical reasons. Instrumented UHPC elements were cast to conduct large-scale field tests. In the field, two UHPC piles have been successfully driven in glacial till clay soil and load tested vertically. Test results, durability, drivability, and other material advantages over normal concrete and steel indicate that UHPC piles are a viable alternative to extend the life of bridge structures.

Jan 1, 2008

By B E. Hall, J Poniewierski, A J. Hills

Following a review of life-of-asset work at MMG’s Rosebery mine in which a proposal to increase production from 0.8 Mt/a to 1.2 Mt/a was mooted, questions were raised as to the seemingly arbitrary reasoning for the production increase. They included: Did the proposal actually add value? Was the production rate from the mine sustainable? Was it the best identifiable value-adding configuration?A multiple scenario analysis study commenced to model how various cut-off grade values against mill throughput, along with associated capital expenditure, would impact on the potential value of the operation. This was carried out utilising the ‘hill of value’ approach promoted by AMC Consultants.The traditional approach to these studies uses a constant cut-off value (NSR – net smelter return) for the whole mine analysis. This was thought to potentially introduce a large amount of variability to the model as different ore types were thought to have different processing costs and different underground lenses were thought to have different mining costs. With the aim of developing a consistent value measure that would be comparable between the lenses, an alternative measure was suggested for all ore block values in this model, irrespective of lens location.The new measure used was a mine variable value (MVV). This allowed for the variable factors of final metal concentrate production to be removed from the ore value. From a mining point this was the haulage distance from ore source to run-of-mine (ROM). For the mill it was the amount of reagents required, varying based on grade together with the amount of power required for crushing, grinding and tailings handling.From the initial run of the model, preliminary results lead to a conclusion of increased value being gained by either increasing cut-off grade or increased mill throughput rate. The validity of the result was tested using alternative price scenarios, which although changed the absolute value achieved did not significantly change the identified value-adding strategies. The realisation of these value increases identified are however contingent on higher sustainable development rates being able to be achieved mine-wide, higher backfilling rates being able to be achieved and overcoming recognised ventilation constraints. Further detailed studies are being put in place to identify the practicality of overcoming these recognised constraints and achieving the higher-value strategies identified.The ongoing objective of the hill of value model built is to keep the model alive as a life-of-asset planning tool and to continue refining the foundation data, such that various mining strategies can be analysed with increased confidence.CITATION:Hills, A J, Hall, B E and Poniewierski, J, 2014. Mining scenario analysis and mine variable value, in Proceedings 12th AusIMM Underground Operators’ Conference 2014 , pp 111–118 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Mar 24, 2014

By James S. Browning

The Bureau of Mines conducted laboratory batch and small-scale continuous flotation tests of weathered mica pegmatite ores from Alabama and North Carolina to determine the technical feasibility of recovering commercial-grade mica concentrates. A new anionic-catonic method was developed for recovering mica in the presence of clay slimes. In continuous tests, concentrates containing 98.1 percent mica were obtained from the Alabama pegmatite ore; the North Carolina pegmatite ore concentrates contained 97.2 percent mica. The recoveries were 83.8 and 81.6 percent, respectively.

Jan 1, 1965

By M. C. McCall

When electric current of any appreciable magnitude flows from a power line into the earth, a change sometimes takes place in the conditions of resistivity immediately surrounding the electrode or medium of contact. If the conducting medium is composed of moist earth or clay the effect is to increase rapidly the resistance. If the conducting medium is coal or a coal bed, the effect is one of slowly decreasing resistance as the coal is carbonized, If, however, the flow of current is not enough to carbonize the coal, it will dry slowly, with a resultant increase in resistance. Measuring ground resistance, or impedance, with conventional commercial ground testers does not always indicate the current that will flow in the earth circuit from a direct-current or an alternating-current power circuit. The exact reason for this has not been determined however, it is thought to be due to the comparatively minute currents used for such testing. A typical ground, tester used by the authors for this work indicated a maximum current of 25 milli-amperes. The frequency of this testing current also has an effect on the readings in all probability. While the possibilities of the effects of varying frequencies has by no means been fully explored in this investigation, there are very definite indications that the impedance of a circuit through a section of earth will vary in some inverse relationship to the frequency of the applied voltages. This is evident at ordinary power-line frequencies ns well as at higher frequencies up to 200 kilocycles, which was the highest frequency available for tests in this investigation. This report is written in the hope that it will stimulate further investigation of the possibilities suggested for communication and the development of safety devices for increased electrical safety in coal mining.

Jan 1, 1952

By B. R. Eichbaum

To develop technology to assure an ample supply of zinc and to reduce environmental pollution, the U.S. Bureau of Mines investigated alternatives to the roast-leach process for treating complex sulfide concentrates. Previous studies proved that low-grade zinc sulfide (ZnS) concentrates could be leached using chlorine-oxygen to produce zinc chloride (ZnCI2). The process involves high energy requirements for evaporating the pregnant solution to produce anhydrous ZnCl2 needed for electrolytic cell feed. An efficient hydrometallurgical process would facilitate treatment of lower grade ores than can be used in conventional processing and would render roasting unnecessary. An alternative method was devised for recovering ZnCl2 from solution. Zinc diammine chloride [Zn(NH3)2CI2] was precipitated from solution by adding ammonium chloride (NH4CI) and sparging with ammonia (NH3) to a pH of 6 to 7.5. The spent solution was treated with calcium hydroxide [Ca(OH)21 at 60° to 80° C for 1 to 4 h to remove remaining zinc and NH3. The Zn(NH3)2CI2 was heated to 300° to 400° C to remove NH3 and produce anhydrous ZnCI2. A possible flowsheet was devised and is included.

Jan 1, 1991

By Claudio Cesar da Costar

O Alto Forno 1 da ArcelorMittal Tubarão, operou entre 30 de novembro de 1983 e 18 de abril de 2012, produzindo 93.915 Mt. Durante esta campanha, inúmeras melhorias foram implementadas para aumentar sua longevidade mantendo o volume e custo de produção. O Alto Forno 1 da AMT é reconhecido como recordista tanto em volume de produção quanto em tempo de operação para uma única campanha. Durante sua reforma, foram empregadas as técnicas de reforma em grandes blocos, as quais foram trocados todo o cadinho, corpo e topo do Alto Forno, trazendo recursos tecnológicos possibilitando obter melhores resultados durante a segunda campanha. Após a reforma, o Alto Forno 1 continua apresentando bons resultados em termos de produtividade, consumo de combustíveis e índices de trabalho, colocando-o entre um dos Altos Fornos com melhores resultados do grupo ArcelorMittal.

Aug 16, 2017

By The DY125-33(Leg 2) Science Parties, Chuanshun Li, Xuefa Shi, Bing Li

"The slow-spreading Mid-Atlantic Ridge (MAR), with a length of ~1.26*104km (Bird, 2003), is the longest mid-ocean ridge on this plant. Separated by the large, left-stepping Equatorial fracture zones, it then be divided into two approximately equal-length parts: Northern Mid-Atlantic Ridge (NMAR, ~6292km) with an average spreading rate of 24mm/yr, and Southern Mid-Atlantic Ridge (SMAR, ~6332km) of 33mm/yr (calculated from PB2002 model, Bird, 2003). Previous works (e.g. Fouquet 1997, Hannington et al., 2011) suggest that slow-spreading ridge could support hydrothermal activities and further favorable for the development of extensive seafloor massive sulfide deposits (SMS). Unlike the NMAR for which large part has been explored for SMS (Hannington et al., 2011; Beaulieu et al., 2015), the SMAR is amongst the least hydrothermal explored spreading ridges until now (Haase et al., 2005, Beaulieu et al., 2015), though both of them show significant similarities in terms of spreading rate, ridge morphology, segmentation, etc. (Macdonald et al., 2001, Sandwell et al., 2014, Tucholke et al., 2008).Before this work, several hydrothermal cruises had been to SMAR since British and German programs starting in 2002, some hydrothermal fields, along with systematic geophysical data, were newly investigated, and types of geologic setting that can host hydrothermal activity were firstly identified (e.g. German et al., 2008; Haase et al.,2005; Haase et al.,2009; Devey et al.,2010; Schmidt et al.,2011).."

Jan 1, 2017

By L. A. Panek, A. J. Barry, John A. McCormick

"INTRODUCTION During recent years, roof bolting has become widely accepted as a systematic method of supporting both coal- and metal-mine roofs. Today, over 2 million roof bolts are installed monthly. Most of the information on bolt installation procedure reported to date (1,2,3,4,5,6) 3/ has been obtained by trial and error by individual groups or operators. To insure good roof control, experience and field tests have indicated that roof bolts should be installed immediately after the exposure of new roof, and they should be preloaded enough to minimize sag of the roof over the opening. The question of the proper initial preload for roof bolts is under study, although it is a general practice to impose an initial load on a bolt of approximately 10,000 pounds. This created a problem of measuring bolt loads at installations in underground mines, which was partly solved by using a commercial-type torque wrench; a device that permits a direct reading of the torque applied to the nut on a roof-bolt assembly from which the corresponding load can be determined by referring to specifications furnished by the manufacturers. However, considerable apprehension was expressed regarding the accuracy of this measuring procedure because of variations in the manufacture of roof-bolting materials and the degree of care exercised in making bolt installations. In the process of loading a bolt, only a small part of the effort is expended in producing strain in the bolt - the larger part of the effort is used in overcoming frictional effects in the nut-bolt-washer assembly. These frictional effects are subject to many factors, such as condition of threads, type of lubrication, if any, the finish on the nut and bearing plate, and the alinement of the bearing plate on the bolt. The object of this investigation was to determine the accuracy with which the load developed in a slotted-type roof bolt installed in a conventional manner in shale or sandstone roof rock can be determined from the torque applied to the nut.This report is the first of a series relating to basic research in roof bolting in underground mines. A future report will cover results obtained using expansion-type bolts under similar conditions. Other reports will consider the efficiency of bolt anchorages, the long period stability of bolts, and the design of safe and efficient roof-bolting systems."

May 1, 1953

By R. Singh

The present paper deals with the development of flotation based process for enrichment of a lead-zinc sulphide ore from Ganesh-Himal region of Nepal. Detailed characterisation and flotation studies were carried out under varying process conditions. The sample assayed 2.47% Pb with 13.6% Zn. The ore was predominantly made up of spahlerite and pyrite in association with subordinate amounts of galena, minor amounts of pyrrhotite and chalcopyrite. Dolomite was the main gangue. The modal analysis showed the probability of fair liberation of sulphides from gangues around 210 microns but the locking of galena with sphalerite and other sulphides continued to finer sizes. Under the optimum process conditions the rougher lead and zinc recoveries were 96.3% and 90% respectively. Multistage cleanings of rougher products proved helpful in improving the concentrate grade, meeting the required specification. Based on the studies undertake a process flow-sheet for the concentration of the ore to individual lead and zinc concentrates was developed.

Jan 1, 2014

By CDC CDC

In 2004, a total of 251 metal mining operations reported employment to the Mine Safety and Health Administration (MSHA). Metal mines were the smallest mining commodity sector, comprising 1.7% of all mining operations. • Gold mines

Sep 1, 2007

By LeRoy D. Loy

To facilitate effective land reclamation and comply with existing state regulations, surface coal mine operators have in recent years adopted new mining techniques and equipment utilization for steep-terrain mining. In contrast to direct spoiling with draglines or shovels, these new mining methods require some form of overburden haulage from the excavation face to the point of reclamation. Although current mining methodologies such as Block-Cut, Modified Block-Cut, and Mountaintop Removal with Head-of-Hollow Fills have proven effective in achieving reclamation objectives, some production problems have resulted from pit congestion and excessive equipment delays. Recognizing this problem, the United States Bureau of Mines contracted Skelly and Loy to design innovative mining concepts utilizing conveyor haulage in place of trucks, loaders, dozers and scrapers. Project objectives required definition of current bottlenecks and development of mining systems to: alleviate bottlenecks; increase production potential; facilitate additional resource recovery; enhance reclamation; reduce safety hazards; and improve mining economics. Successful completion of project goals within a four year program involves systematic implementation of the following separate work phases: 1) Develop Concepts for Block-Cut Mining Systems; 2) Determine the Economic and Technical Feasibility of Concepts; 3) Prepare Detailed Design and Specifications of Concepts; and 4) Prepare Specifications for Conducting Field Tests of the Most Promising Concepts. At the time of this publication, Phases 1 and 2 are finalized with Phase 3 efforts well underway.

Jan 1, 1977

By Junmo Ahn

This study investigated leaching kinetics by alternative lixiviants for copper leaching from chalcopyrite (CuFeS2), the most abundant copper resource in the world. As a refractory sulfide mineral, chalcopyrite shows low copper extraction due to passivation on chalcopyrite surface. Also, decrease of copper grade with high portion chalcopyrite requires the alternative leaching procedure to increase copper recovery. Therefore, alternative lixiviants such as sulfurous acid and methanesulfonic acid (MSA) were tested for both concentrate and low grade ore to enhance copper extraction. Also, an oxidant, hydrogen peroxide, was compared to ferric to find out the improvement of leaching kinetic. In concentrate leaching tests, 30 g/L MSA showed the highest copper extraction (47%), compared to other lixiviants at 75 °C. Periodical H2O2 addition enhanced copper extraction, and above 90% of copper extraction was observed within 96 h by periodical addition of 0.6% H2O2 at 75 °C. The activation energy of chalcopyrite leaching by MSA and H2O2 achieved 40 kJ/mol, which is chemical reaction control. The results of low grade ore leaching tests indicates that no significant difference among lixiviants (H2SO4, H2SO3 and MSA) with ferric was observed, all of which achieved around 37% within 24 h at room temperature. However, significant increase of copper extraction (>80%) was observed at both 20 g/L MSA and 10 g/L H2SO4 conditions by the addition of 10% H2O2.

By Jeffrey M. Taylor, Arturo Ressi di Cervia

"Construction of the drilled shafts for the Brightman Street Bridge Replacement Project were not only challenging due to working over the water but were also challenged by changed soil conditions, concurrent work being performed by an adjacent contractor on the same project, environmental restrictions and severe winter conditions. A total of 36 x 8 foot (2.44m) diameter drilled shafts with 7.5 foot (2.31m) rock sockets were installed for the East and West bascule piers. This project also included Osterberg Cell load testing on two production drilled shafts at both the East and West bascule piers. The results from the load test program were used to fine tune the design of the drilled shaft rock sockets. From a constructability standpoint the reverse circulation drilling method with a pile top drill rig proved to be an excellent choice for drilling the overburden and rock sockets of the large diameter deep drilled shafts. INTRODUCTIONThe replacement Brightman Street Bridge spans the Taunton River between Fall River and Somerset in Massachusetts.The new crossing is located approximately 1500 feet (450m) upstream from the existing Brightman Street Bridge, which was built in 1908. The new mainline bridge includes nine spans totaling 1725 feet (525m). A bascule type moveable span will be located in the middle of the Taunton River and provide a 200 foot (61m) open channel centered about the 400 foot (122m) navigational channel. The bascule span, which has a span length of 409 feet (124.7m), will be a trunnion-type four leaf structure with a solid deck. A site plan is shown in Figure 1 Contract 3, which includes construction of the foundations for the East and West bascule piers, was bid on December 19, 2000 and was awarded to Modern Continental Construction Company (MCC) on January 24, 2001. MCC in turn awarded the subcontract for the installation of the drilled shafts to TREVIICOS Corporation, which started mobilizing in June of 2001.The scope of work for the drilled shafts of Contract 3 consisted in installing 18 drilled shafts in three rows on each side of the river to support the bascule piers located in the middle of the Taunton River.The foundation plan for the bascule span is shown in Figure 2."

Jan 1, 2004

By E. Bonsall, J. J. Brummer, A. R. Graham

"A method and device are described for sampling diamond-drill core by cutting a continuous fillet of constant cross section from the cylindrical surface of the core throughout appropriate sample lengths. The apparatus employs a tapered, abrasive-set, cutting wheel, the conical cutting surface of which projects slightly into a rectangular core-guiding trough set parallel to the axis of rotation. The depth of fillet and thus the amount of sample per unit length can be regulated by adjusting the core guides. The freshly cut fillet itself, by engaging in a guide beyond the cutting wheel, acts to prevent rotation of the core during operation of the device.The cuttings which form the sample are normally collected in a tray below the cutting-wheel and appear at about 80 per cent -100 mesh. They require little or no further treatment or comminution before analysis. Speed, economy and convenience of sampling are thus greatly increased as compared with conventional sampling by im-1>act breaking or sawing, followed by crushing, grinding and sub division for assayAssays from fillets (about 1/20 the cross-sectional area of the core) and from 180-degree segments, from the same ninety-three core-samples, representing 431 feet of nickel-copper mineralization, gave the following results:"

Jan 1, 1968

By J. F. Shultz

The Bureau of Mines investigated the hydrogenation of carbon monoxide and carbon dioxide over Raney nickel catalyst and nitrided fused-iron catalyst using both a single-pass and a recycle system. Activation energy over Raney nickel catalyst is 29 to 32 kcal/mole for synthesis from either CO or CO2, Pressure dependence of the gas conversion is to the 0.3 power for synthesis from CO and to the 0.5 power for synthesis from CO2. Nitrided fused-iron catalysts were tested using high recycle rates and 3H2+lCO, 2H2+lCO, and 1H2+lCO feed gas at 21.4 atmospheres absolute pressure. The relative usage of hydrogen (moles H2 consumed per moles Ha+CO consumed) was larger than in corresponding single-pass tests, and the relative usage of hydrogen approached the feed gas ratio monotonically as conversion increased. Activation energy was found to be 12 or 13 kcal/mole fresh feed gases of 3H2+lCO or 2H2+lCO. For single-pass operation the activation energy under the same conditions was 19 to 21 kcal/mole.

Jan 1, 1967

By Jim Huerta

Diesel fuel usage in the mining industry continues to escalate. This is because approximately 60 percent of all mined materials are surface extracted by large equipment using diesel fuel, which continues to increase in cost per gallon. For example, coal mining uses large equipment such as wheel loaders, wheel dozers, draglines and [ ] dredgers. In one year, three of the largest U.S. coal mining operations consumed approximately 567 million to 852 million L (150 million to 225 million gal) of diesel. At an approximate cost average of $3.25/gal the expenditure on diesel is $487 million to $731 million per year. So, are there any solutions that could reduce this cost burden? Yes, there are. Coal mining companies can extract less ore; use more efficient extracting equipment that consumes less fuel; wait for a significant reduction in the cost of fuel; or find and use technology that would create efficiencies that would lower the cost. Nanotechnology is one such technology that might provide the means to create the efficiencies that will significantly lower diesel fuel costs.

Jan 1, 2011

By H. M. Thorne

Industrial shale-oil operations in North America and Europe predated the Drake discovery, but, since then, most have succumbed to competition from petroleum. However, the existence of enormous oil-shale resources in the Green River formation of Colorado, Utah and Wyoming [estimated at over a trillion bbl of shale oil in place] and the advancement of United States oil- shale technology by research and development programs of government and industry during the past 15 years point to a natural partnership of petroleum and oil shale to meet the accelerating energy demands of the future. The utilization of oil shale is not a question of limited petroleum supplies, but one of economics. Two factors are expected to improve the economic outlook for industrial shale oil production -- a rise in petroleum replacement cost and further advances in oil-shale technology.

Jan 1, 1963

By A. S. Yue

It was deemed desirable to obtain an understanding of the vacuum desulfurization process. McKechnie1 has reported that the sulfur content of nickel- and cobalt-base alloys is reduced in vacuo. Keverian and Taylor2 have observed that vacuum melting causes desulfurization of iron-carbon-silicon alloys. Garnyk and samarin3 have desulfurized transformer steel by vacuum treatment. Experiments were conducted in order to investigate the desulfurization of liquid iron under reduced pressures, and to establish the effect of some alloying elements, and various crucible materials. A vacuum-induction furnace of 50-lb capacity was used. The charge was Armco iron. Silicon was added as 90 pct ferrosilicon, carbon as electrode graphite, and aluminum as high-purity aluminum metal. Magnesia and silica crucibles were used, their inside diameters were 5 1/2 and 5 3/8 in., respectively. The temperature was measured with an optical pyrometer and it was held at 1600 1 15°C. Samples were withdrawn with quartz tubes of 6 mm ID, without disturbing the furnace atmosphere. Pressures were measured with an alphatron gage. The experimental results are shown in Fig. 1. They indicate that: 1) Sulfur can be removed from liquid iron alloys by vacuum treatment; 2) The desulfurization is enhanced by the presence of silicon, carbon, and aluminum, all these elements increase the activity of sulfur dissolved in liquid iron;4 3) The pronounced effect of silicon indicates that probably a volatile silicon sulfide is formed, Alcock and Richardson5 have observed a similar phenomenon; 4) The same rate of desulfurization was obtained when the metal was contained in either magnesia or silica crucibles. Dr. J. Keverian has contributed many discussions and recommendations. M. S. Sutliff has helped in conducting the heats. The permission of General Electric Co. for this publication is gratefully acknowledged.

Jan 1, 1960