Search Documents

By C Agreda

The Cushion Blasting Technique applied to solve the high risk case history represented by a 10,704 TM rock locate at 120 M from the hydroelectrical plants of 350 KV each, is described, analyzed and discussed. The generation and distribution of 700 KV produced by two hydroelectrical plants must not be interrupted by any reason, because the 26 district of the province of cajatambo, of the Lima department; would not have electrical power. The search of the best alternative and methodology, the drilling and blasting pattern calculations, charge design and loading, connections and initiations of the 50 blasts are described, analyzed and discussed. Finally, the excellent results from a technical, economical, enviromental and safety point of view of the 50 primary blasts are discussed and emphasized.

Jan 1, 2005

By Ray H. S, Galgali R. K

It is well accepted that the blast furnace will continue as the main route for iron-making for many more years. However, its limitations have motivated researchers to look for alternative routes, particularly, those where non-coking coal is used for liquid iron production. Smelting reduction (SR), where coal and oxygen are used to produce liquid iron and power is now receiving serious attention. Several smelting reduction reactors are now operating in pilot plant scale and one or two have reached commercial status.

Jan 1, 1999

By Bhaskar B. Thapa, Christopher Laughton, Michael P. Bruen

At Fermilab, located in Batavia, Illinois, a 4,000-foot underground complex of tunnels and caverns is being excavated on a decline of six percent, at depths of up to350 ft, below grade. The site geology consists of dolomitic and shale formations overlain by glacial till. Since the start of construction in March 2000, work to date has concentrated on the excavation and support of the Target Hall cavern, which is characterized by a low rock cover and a final lining of shotcrete. Ground vibrations, noise levels, and rock movement were monitored during excavation by drill and blast methods to prevent damage to experimental facilities, impacts on surrounding communities, and to allow evaluation of cavern performance. The cavern design was based on a UDEC numerical analysis that was validated during construction by comparison to encountered conditions and measured cavern movements.

Jan 1, 2001

By J. E. Scott, L. M. Heaman, R. A. Creaser, G. S. Salazar

"Schaft Creek is a calc-alkaline porphyry Cu-Mo-(Au) deposit located in northwestern British Columbia. The deposit formed in a volcanic arc setting, likely on a back-arc rifted continental fragment. It is hosted by Late Triassic basaltic to andesitic volcanic rocks of the Stuhini Group (Stikine Terrane), and is associated with porphyritic granodiorite dikes emanating from the nearby Hickman batholith. The age of the Hickman batholith is approximately constrained here by a composite U-Pb zircon date of 222.1 ± 9.6 Ma, which is in broad agreement with a well-constrained age for mineralization at Schaft Creek of 222.0 ± 0.8 Ma (Re-Os molybdenite). The deposit is in most respects typical of calc-alkaline porphyry systems, but displays silica-poor sericite-chlorite alteration in mafic country rocks in place of classic phyllic altera¬tion. The deposit comprises three distinct, but related, zones: the northern Paramount zone, the Main zone, and the West Breccia zone. Two phases of mineralization are observed. The first phase occurs as hydro-thermal veins and breccias, and minor disseminations. It consists of bornite, chalcopyrite, molybdenite, and pyrite with potassic and sericite-chlorite alteration. The second phase is minor and consists of veins of molybdenite ± specularite, as well as Cu-Pb-Zn sulfide veins without any significant corresponding alteration. Extensive structural modification has affected the deposit both during and after its formation.Schaft Creek est un gîte porphyrique de Cu-Mo-(Au) calco-alkalin situé dans le nord-ouest de la Colombie Britannique. Ce gîte s’est formé dans environnement d’arc volcanique, probablement situé sur un fragment continental bordé par un bassin d’arrière-arc. Le gîte est encaissé par les roches volcaniques basaltiques à andésitiques du Groupe de Stuhini (Terrane de Stikine) d’âge Triasique tardif, et est associé à des dykes de granodiorite porphyrique provenant du batholithe de Hickman avoisinant. L’âge du batholithe de Hickman est estimé par un âge U-Pb composite sur zircon de 222.1 ± 9.6 Ma, lequel est grossièrement en accord avec l’âge de la minéralisation de Schaft Creek, estimé a 222.0 ± 0.8 Ma (Re-Os sur molybdénite).Ce gisement, bien qu’à plusieurs égards typique des systèmes porphyriques calco-alcalins, présente une altération en séricite-chlorite pauvre en silice dans l’encaissant mafique a la place de l’altération phyllique classique. Ce gîte comprend trois zones distinctes bien que connexes : la zone Paramount au Nord, la zone Principale et la zone West Breccia. Deux phases de minéralisation sont observées. La première phase se présente sous forme de veines et de brèches hydrothermales ainsi qu’en disséminations mineures et consiste en bornite, en chalcopyrite, en molybdénite et en pyrite avec une altération potassique et en séricite-chlorite. La seconde phase est mineure et consiste en veines de molybdénite ± spécularite ainsi qu’en veines de sulfures de Cu-Pb-Zn sans association à une altération particulière. Le gisement a été profondément modifié par la déformation a la fois durant et après sa formation."

Jan 1, 2008

By L. L. Chasko

A mine fire is one of the most challenging safety issues facing a mine operator and can occur at any location underground. The National Institute for Occupational Safety and Health (NIOSH) and the Twentymile Coal Mine, Colorado, conducted in-mine experiments to determine the capability of high-expansion foam for addressing underground fires. The tests were conducted in sloping entries with high-capacity diesel-powered foam generators. The following results were observed: a well-designed, maintained, and properly operated high-expansion foam generator can propagate a foam plug hundreds of feet in steep upward sloping (20 pct) multiple entries against a ventilation pressure; stoppings and partitions designed to contain the foam plug in upward sloping entries must be substantially constructed; and the predicted quantity of foam concentrate can be significantly less than the actual amount used due to foam losses, such as bubble breakage on dry surfaces. This paper describes the production of high-expansion firefighting foam and discusses the in-mine experimental tests and results. DISCLAIMER: The findings and conclusions in this report are those of the author(s) and do not necessarily represent the views of the National Institute for Occupational Safety and Health.

Jan 1, 2009

By Stanley K. Haines

This Bureau of Mines publication comprises 19 tables of data concerning domestic barite production and consumption, imports, and world production for the years 1880 to 1976. Barite is vital to the petroleum industry, with 90 percent of domestic consumption used in drilling muds. Domestic production has traditionally fallen short of consumption: in 1976, 41 percent of the 2.2 million tons consumed was imported. World production of barite increased from 269,000 tons in 1923 to 5.2 million tons in 1975 but is in danger of falling short of future demand. The compiled data provide a comprehensive base of information.

Jan 1, 1978

By A-A. Bogno, Ch. -A. Gandin, A. Maitre, H. Henein

Most metallic materials are produced from their liquid state. In order to control the properties of industrial products, it is very important to understand their solidification path and the resulting microstructures which can be significantly affected by melt undercooling. High undercooling results in rapid solidification and a refined microstructure with minimal microsegregation. This paper reports on the analysis of rapidly solidified Al-Cu droplets obtained by a single fluid atomization process, Impulse Atomization. A quantitative analysis by Rietveld refinement method of the Neutrons Diffraction data was carried out to determine the fraction of the intermetallic Al2Cu. Knowing the fraction of Al2Cu, the eutectic fractions and corresponding dendritic and eutectic undercoolings were estimated using the metastable extensions of solidus and liquidus lines of the Al-Cu system calculated by Thermo-Calc. In addition to this work, a model of microsegregation coupled with ThermoCalc software via TQ (application programming interface of ThermoCalc) and the Wang-Beckerman model for dendritic growth velocities has been developed for binary alloys. This has led to the development of a phenomenological relationship between primary phase undercooling and initial growth velocity. A comparison of estimated primary undercoolings using a coarsening model with the adiabatic undercoolings for each alloy composition has confirmed that solidification occurs under adiabatic conditions during recalescence.

Jan 1, 2014

By B. Mishra, A. Staley, D. Kirkpatrick

The major waste product of the alkaline extraction of alumina from bauxite [Bayer Process] is known as red-mud. Approximately, a ton of red-mud is produced for every two tons of bauxite mined. The red-mud produced from Jamaican bauxite is rich in hematite, alumina and titanium oxide. It has been shown that over 90-wt. pct. alumina can be recovered from red-mud by soda-ash sintering and caustic leaching. Hematite can be carbothermically reduced with a degree of metallization of over 94 pct resulting in attempts for magnetic separation. These separations are desirable in the notion that there is no waste product generated from this type of processing and consequently an opportunity for complete utilization of the waste material. Conversely, the pre-separated material could be charged through the tuyeres in an iron blast furnace or smelted to produce pig iron. If smelted, the concentration of titanium oxide in the slag will be significantly high justifying its recovery by established acid-leach process. This paper describes the results of alumina recovery and the plans for titanium oxide recovery from red-mud. In addition, the situation of ongoing efforts in iron extraction, particularly, the method of magnetic separation of the reduced material. The problems associated with the use of reduced red-mud as an alternative to direct-reduced iron [DRI] has also been discussed. Critical assessment of the recovery sequence chosen for the products has been described based on economics.

Jan 1, 2001

INTRODUCTION ò World coal production, Exporters and Importers òNew Zealand Exports, Markets and Products ò Types of Markets and Price Setting ò Bench Mark Prices and Exchange Rate ò Transport ò International Marketing - Key Factors ò Coal New Zealand , the Challenges

Jan 1, 1996

Filtration of pulps of varying densities is an essential operation in the hydro-metallurgical production of zinc. The use of filters naturally applies only to the "wet" plants, and in these varying types and sizes are in commission. At Risdon, the Moore suction filter is used for the heavier pulps, except in one instance, where a modification of the Butters-Cassell filter is installed.Filter presses are in general use, and of these, one is a washing unit; the plates, and frames are of cast iron or mild steel, except in one case which is a centre feed press having wooden frames.FILTER DESIGNThe problem of filtration presented itself very early in the history of Risdon and the first developments occurred in what was termed the 250 -lb. plant. Here experiments were made with many types of filters, and as this was the pilot plant on which the design of the 10 ton plant (10 tons of zinc per day) was based, quick decisions were necessary.An Oliver type filter was chosen for the heavier pulp or residue, and a Shriver wooden frame filter press for the lighter pulps.To this day, but with a number of variations, filter presses continue to function unopposed in their particular field; however, the Oliver filter was soon superseded because it was found impossible to wash the filter cake efficiently without repulping; consequently its use was abandoned and the Moore filter adopted.Both- these filters have been modified and developed in many ways to meet the requirements of a zinc plant, but they retain their original basic features.

Jan 1, 1949

By Yeruva Ramanareddy, Sohail Wajid, Ahmed Shaz, K. Bhavani

"CP-06 is an NATM cross passage which connects up-line and down-line metro tunnels near Kilpauk Medical College, Chennai. It lies completely in loose silty sand to dense sand with water table almost touching the ground surface after Chennai floods. Pre-grouting was done before excavation to seal the area and to ensure no-loose pockets. The heading was excavated successfully but while benching excavation huge water ingress started seeping out. Sand also permeated along with water which became unstoppable due to cavity formation and caused the up-line tunnel to sink considerably. A large grouting exercise was carried out with different grout materials and techniques both from the ground surface and inside of tunnel to stop the water ingress and stabilize the tunnel. This paper describes the chronology of events that occurred in the tunnel during CP-06 issue. It elaborates all the different grouting techniques involved in the whole process of the tunnel stabilization. It includes a finite element analysis using Rocscience RS2 9.0 software showing the possible cause of sand incursion with water from the CP invert which lead to the tunnel settlement. This paper also describes the after effects and the lesson learnt from the whole incident.INTRODUCTIONConstruction of Metro Rails has become the latest alternative to cope up with the transportation demand of the growing urban cities population. L&T SUCG JV constructed Chennai Rail Metro Phase II Contract UAA-04 which included design and construction of approximately 4 km of route length of underground mass transit railway including 3 underground stations. This package also includes 12 cross passages which are NATM tunnels connecting upline and down-line side of TBM tunnel for safe evacuation of passengers in case of emergency. As per NFPA guidelines, this is a mandatory structure and there should be atleast one cross passage in 244m tunnel length.CP-06 is a cross passage connecting upline and downline tunnel between Pachiyappa College Station and KMC Station, in Chennai Metro. During the construction of CP-06, heavy water seepage of around 450 liters per minute was encountered during second round of benching excavation after full heading was excavated. An inflow of around 12-15 cum of sand and silt was also observed inside the tunnel along with the seepage water, which created piping inside the TBM tunnel causing it to settle continuously with time. A huge effort was made to stop the water ingress along with loose sand which was causing the running tunnel to settle, involving all possible grouting methods and temporary support installation."

Jan 1, 2017

By V. A. Melezhik, A. H. Green, L. N. Grinenko

Finally, a theoretical model is constructed that takes

Aug 1, 1994

By George H. Holmes

The water situation in Nevada mineral and related industries is described in this report. It contains information on the sources and adequacy of supply to current operators, requirements and uses, quality and costs, geography, hydrography, precipitation and evaporation characteristics, and Nevada water laws. Also, information is given on the water requirements of one public utility powerplant, and the source and consumption of water in four major cities. Water distribution at 24 operations is shown on schematic waterflow diagrams. The mineral industries of Nevada in 1962 used 8.6 billion gallons of new' water and reused 3.8 billion gallons for a total usage of 12.4 billion gallons. The copper industry was the major water user. The 1962 value of all mineral production in Nevada was $85.5 million. The large amount of water required to maintain thin high production is obtained principally from ground-water sources in alluvial valleys and the permeable rock formations of some mountain ranges. Some water is also obtained from perennial streams and springs. Sources of water utilized by existing industry ire near most mineral industry operations; however, seven companies are forced to pipe water distances ranging from 2 to 8 miles. Although water supplies of presently operating companies are adequate at most operations, several companies resort to large-scale reuse of water as a matter of conservation and economics. Acquisition of water by new operators is possible but takes considerable negotiation. Water rights, surface and underground, are controlled by the State. The quality of the water is satisfactory for most purposes. Analyses of 19 samples, listed in the appendix, show the range in water quality at various plants throughout the State. Costs of delivering new water to current operations range from 2 to 26 cents per 1,000 gallons with an average of 10 cents per 1,000 gallons for power and maintenance. No firm costs for recirculating water were available; estimated costs range from 1.5 to 2.5 cents per 1,000 gallons. The mineral-product value of the entire Nevada mineral industry in 1962 was equivalent to $10 per 1,000 gallons of new water and $26 per 1,000 gallons consumed. Projection of the 1962 water requirements of the Nevada mineral industry indicates that the demand For new water will increase from 8.6 billion gallons in 1962 to 11.9 billion gallons in 1980, a 43-percent increase. Water requirements in the year 2000 are estimated as 14.8 billion gallons, an increase over 1962 water demand of 78-percent.

Jan 1, 1966

The SFR system utilizes a skimmer or extractor placed at or near the slurry-froth interface where there is a higher concentration of valuable mineral particles. With assistance of hydrocyclones, it is possible to classify the extracted particles into coarse and fine particle streams, that can be handled separately. It also allows the coarser solids to be separated from entrained low-value fines. The first test results with the SFR system significantly improved both coarse and fine particle recovery in a flotation cell. The SFR system was tested in the flotation circuit at a copper-moly concentrator, and the results show that the use of the skimmer has huge potential to increase the froth recovery (Rf) of both molybdenum and copper.

Jan 1, 2012

By E. Morrice

As part of its efforts to maximize process efficiency and decrease energy requirements in mineral processes, the Federal Bureau of Mines has investigated methods for beneficiating bastnäsite ores from Mountain Pass, Calif. The results of a bench-scale study on the flotation of bastnäsite ore are presented. Flotation at a pulp temperature of 40° to 45°C yielded a cleaner concentrate containing 58.7 pct RE203 at a rare-earth recovery of 67 pct. These results are comparable to those reported for the commercial beneficiation method in which the pulp is heated to boiling before flotation. An attempt was also made to recover a barite flotation concentrate from the bastnäsite rougher tailing. Concentrates containing only 70 pct barite were obtained.

Jan 1, 1982

By K. Najim, D. Hodouin

"The raw ores which are processed in mineral processing plants exhibit very strong variations of their physical and chemical properties. As a consequence, the performances of the comminution and separation processes vary greatly from time to time. Model-based control strategies improve the performance of the plant; however, they require some form of adaptation to cope with the variations of the are properties.This paper deals with the use of adaptive techniques for the control of mineral processes. It begins with a survey on adaptive control algorithms including parameters estimation aspects. Then several examples dealing with crushing, rod, ball, autogenous and semi-autogenous grinding, flotation , drying and calcination processes are reviewed.IntroductionThe operation of the various processes of mineral processing plants (crushing, grinding, flotation, dewatering, etc.) is generally controlled using empirically tuned regulators of constant structure, such as PID controllers. To improve the operation performance, mineral processors try to implement specifically designed controllers, i.e. controllers based on plant dynamic models. Most of the time, these techniques improve the control of the mineral processing installations. However, modelling is a complex procedure because of the problems of measurement and data management, specific to this industry, and because of the variations of the model parameters. In this context model-based control strategies do not always bring the expected improvements or are sometimes discarded and replaced by more conventional techniques .The sources of variation of the dynamic behaviour of mineral processing systems can be classified into three categories: (I) the inherent changes of the raw ore properties (composition, grindability, mineralogical texture, etc.); (2) the process tuning modifications (grinding media loads, number of hydrocyclones, slurry level in flotation cells, agitation speeds, etc.); (3) the feedrate variation of the ore, water, chemical reagents, etc. All these factors change the fundamental properties of the process dynamics such as the grinding or flotation rates and the residence time in the equipment. The simplified linear models which are used to describe the process dynamics are not able to track the complex behaviour of the mineral processing systems when the amplitude of the sources of variation are too large. The mismatch between the model and the plant behaviour is then frequently a cause of model-based controller failures."

Jan 1, 1992

Jan 1, 1965

By T. T. Tomimatsu

[This Bureau of Mines paper investigates explores, and analyses the Corporate structure dynamics and Rancid role to evaluate the economic health of the U.S. copper producers. It highlights the Corporate policy options and measures of corporate profitability and suggests that a competitive domestic copper industry will exist in the future. The study highlights the activities of 14 selected major copper-producing companies, including their subsidiaries o affiliates, that were responsible for more than 95 percent of the total U.S. production in each of the years since 1969. The selected firms are hot all primarily in the business of producing copper. Several of the large producers are classified by the financial institutions as integrated oil and gas enterprises.]

Jan 1, 1980

By J. Yuan

Ground calcium carbonate (GCC) and chemically precipitated calcium carbonate (PCC) have become important mineral-based commodities in recent years. GCC manufacturing generally requires high purity and high brightness deposits of marble, chalk or limestone as the stone source. PCC usually uses limes made from lesser quality limestone deposits. GCC products have a wide span of particle size, with a d50 size ranging from sub micrometers to as large as several inches such as those used in landscaping. PCC products are typically limited to less than 10 µm (1,250 mesh). Each PCC product has a narrowly distributed size range. GCC and PCC products tend to have higher levels of whiteness com-pared with other traditional filler and extenders, such as kaolin and talc. Published statistics of GCC production volume often vary due to the exclusion of certain size range GCC products. According to Roskill’s latest estimate, world GCC capacity was believed to exceed 56 Mt (62 millionst) during 2004 for all grades.

Jan 1, 2005

By S. Shi, J. Y. Hwang, B. Li

Silver, copper, and zinc are commonly known elements with antibacterial and antifungal capabilities. Attempts have been made to dope silver on minerals, glass, and ceramics and the resulting materials have been investigated for their antibacterial and antifungal properties. Since silver is expensive and very reactive, silver doped materials have been found inappropriate in some applications. Copper-vermiculite is investigated as an alternative. Vermiculite has high cation exchange capacity on the magnesium ion in the crystal structure. Copper ion may have a high tendency to replace magnesium because of similar charge interference and ionic radius. Copper-vermiculite is prepared by reacting vermiculite and copper chloride solution. By impregnating copper ions into the nanometer openings between the layers of vermiculite, it is possible to render the composite with antibacterial functions if the copper ions could be released gradually from the composite. The antibacterial efficiency of Cu-vermiculite against Escherichia coli was studied using the Halo method. The results show that Cu-vermiculite is effective for preventing the reproduction of the bacteria. Heat treatment of Cu-vermiculite at up to 400°C does not show significant changes in antibacterial activities.

Jan 1, 2002