Search Documents

By Indrajit Paul, Atanu Pal, Kapil Modi, Sanjay Chandra, Chandra Sekhar, Srinivas Dwarapudi

"High alumina content in the Indian iron ore fines (2.5% Al2O3) resulted in poor quality pellets at the recently commissioned 6 MTPA pelletizing plant and a study was under taken to establish suitable pellet chemistry through proper fluxing agents. Limestone fluxed pellets were prepared at varying basicity (0 to 0.8) and pyroxenite fluxed pellets at varying MgO contents (0 to 3%) to study their effect on the metallurgical properties. Fired pellets were tested for their strength, RDI, reducibility and swelling. Microstructural studies, optical and SEM-EDS, were carried out to quantify different phases and their chemistry. Acid pellets exhibited poor quality whereas limestone pellets at 0.8 basicity and pyroxenite pellets at 1.5% MgO exhibited optimum metallurgical quality. Formation of widely distributed silicate melt in limestone pellets and high melting point slag & magnesioferrite in pyroxenite pellets found to improve their quality. However during commercial production of MgO bearing pyroxenite pellets, their room temperature and low temperature properties found to be inferior, but exhibited better high temperature properties, viz. softening-melting behavior. Contrary to this, commercially produced limestone pellets, comprising CaO, exhibited better strength and RDI but showed poor high temperature properties. To yield the benefits of both CaO (for good strength and RDI) and MgO (for low swelling and high softening), a dual flux combination was established by using both limestone and pyroxenite/olivine together that resulted in optimum metallurgical properties. Coke rate at the blast furnaces found to be reduced by 1kg for every1% increase of dual flux pellets in the burden.INTRODUCTION Iron ore agglomerate quality plays a vital role in decreasing the reducing agent consumption and increasing the productivity of blast furnace. In most of the integrated steel works, the burden mix for blast furnace is decided as per the availability of the iron ore agglomerates like sinter and pellets. More attention has been given in recent years to the use of fluxed pellets in blast furnace due to their good strength and improved reducibility, swelling and softening melting characteristics. Generally, quality of pellets is influenced by the nature of ore or concentrate, associated gangue, type and amount of fluxes added and their subsequent treatment to produce pellets. These factors in turn result in the variation of physicochemical properties of the coexisting phases and their distribution during pellet induration. Hence properties of the pellets are largely governed by the form and degree of bonding achieved between ore particles and the stability of these bonding phases during reduction of iron oxides (Panigraphy et al., 1990). It is important to note that conditions and parameters of pelletizing are specific to given ore or concentrate; the present study is undertaken for typical Indian hematite ore fines high in alumina. Except authors earlier work on quality of pellets from Indian iron ore (Dwarapudi et al., 2008, 2010), there is no considerable literature reported on the effect of pellet basicity and MgO content in the basicity range of 0 to 0.8 for Indian hematite ore."

Jan 1, 2018

By Rodrigo Vitorino da Silva

Ligas a base de zircônio são utilizadas na indústria nuclear devido à suas boas propriedades mecânicas, baixa absorção de nêutrons e boa resistência à corrosão. No entanto, durante a operação do reator, o hidrogênio é absorvido pela liga, resultando na formação de hidretos. Para aumentar o tempo de operação desses componentes é necessário o desenvolvimento de novas ligas que retardem ou diminuam esse efeito. Este trabalho tem como objetivo avaliar a influência dos tratamentos termomecânicos no zircônio puro, através de testes que avaliem a corrosão, absorção e dessorção de hidrogênio nas condições laminada a frio e tratada termicamente. Análises de difração de raios-X indicam a existência de uma matriz Zr-a para as condições analisadas. Após a hidrogenação são formados ZrH e ZrH2. O zircônio puro encruado absorveu 1,23%p H. O zircônio puro laminado e tratado termicamente absorveu 0,85%p H. O resultado de DSC mostra que a decomposição dos hidretos ocorre em faixas de temperatura entre 318 e 368°C para a condição tratada termicamente. Para condição laminada, o resultado mostra uma transformação de fase entre 565 e 650°C. O conjunto de resultados permite concluir que a amostra tratada termicamente absorve menos hidrogênio, porém o início do processo é menor. A amostra tratada termicamente é menos resistente a corrosão e a velocidade da corrosão é menor.

Aug 16, 2017

By R. Simon, L. Yarborough

This paper presents a correlation for predicting the critical pressures of gas-solvent-reservoir oil systems of the type encountered in gas and solvent injection processes. Experimental data from 14 systems were used to develop the correlation which expresses critical pressure as a function of composition, C7+ mol weight, and C7+ characterization factor. Critical pressures predicted by the correlation for the 14 gas-solvent-reservoir oil systems have an average deviation of 2.8 per cent of the experimental values. The correlation war used to study a wide variety of other hydrocarbon mixtures reported in the literature whose critical conditions are in the range of interest in oil recovery work (100 to 280F and 2,000 to 6,000 psia). Critical pressures predicted by the correlation had an average deviation, expressed as per cent of experimental value, of 5 per cent for 20 miscellaneous mixtures from the literature, and 6.4 per cent for I7 methane-butane-decane mixtures reported by Sage and Lucey. INTRODUCTION Predicting critical points of hydrocarbon mixtures is an important part of phase behavior calculations. If the critical point can be predicted for a specific mixture, the separation between the bubble-point and dew-point regions will be defined, and physical properties of the mixture can be calculated by using the principle of corresponding states. Numerous correlations for predicting critical points of hydrocarbon mixtures have been published. Six of these correlationsl-8 were for light hydrocarbons, and two correlations7,8 ere for high boiling-point petroleum distillates. Organick9 And Eilerts" presented correlations which combined the published data from both light and heavy mixtures, and these correlations became the only available methods for predicting critical pressures for wide boiling range mixtures. In the course of the authors' work on secondary recovery by gas and solvent injection, experimental data were obtained for 14 mixtures of dry gas, ethane-propane-butane solvents, and various reservoir oils. The critical pressures and critical temperatures of these gas-solvent-reservoir oil systems were in the range of 1,900 to 4,800 psia and 180 to 265F. The critical pressures predicted for the 14 mixtures by the correlations of Organick and Eilerts had an average deviation from the measured values of about 13 per cent. The authors felt that it was necessary to develop a better correlation for engineering calculations and the resultant correlation, which is presented on Figs. 1 and 2, predicts the critical pressures of the 14 mixtures with an average deviation of 2.8 per cent. The validity of the correlation was tested by applying the correlation to other hydrocarbon mixtures reported in the literature. This subject is discussed later in the paper. The authors feel that there is also a need for an improved critical temperature correlation for gas-solvent-reservoir oil systems. However, developing a critical temperature correlation is a significant study in itself and is not included in this paper. EXPERIMENTAL DATA The compositions and critical points obtained by the authors for 14 gas-solvent-reservoir oil mixtures are shown on Table 1. The methane concentrations in these mixtures varied from 20 to 63 mol per cent. The intermediate hydrocarbon group, consisting of ethane, propane, and butane, varied from 20 to 64 mol per cent, and the concentration of the C,, fraction from 10 to 20 mol per cent. The physical properties of the C,, fraction covered the range from light, paraffinic, nonasphaltic (Mixtures 5, 6, 7, 8, 9 and 10) to heavy, aromatic, and asphaltic (Mixtures 13 and 14).

By Afshin Sadri

Uma das principais razões para o reparo de altos-fornos é a perda do revestimento refratário, principalmente nas regiões da soleira e onde são feitos os furos de corrida. A operação intensa dos altos-fornos pode resultar em desgaste e deteorização extensiva do material refratário. Isto pode, então, afetar a continuidade das operações e a vida útil do forno. Novo-Lipetsk (NLMK) e a Hatch desenvolveram uma abordagem sistemática para monitorar a condição do revestimento da soleira dos altos-fornos usando Acousto Ultrasonic-Eco (AU-E), um sistema de ensaios não-destrutivos desenvolvido pela Hatch. Inspeções contínuas e periódicas dos altos-fornos revelaram áreas com deterioração acelerada do material refratário, formação extensa de “elefant foot” e acelerado desgaste do refratário, assim como fissuras e outras anomalias. Para prolongar a vida do forno, mantendo a intensidade de suas operações, algumas modificações, tais como a melhoria da qualidade do coque e da limpeza das placas de resfriamento e adição de óxido de titânio, entre outras medidas, foram recomendadas e aplicadas. Este trabalho demonstra como esforços coordenados entre a NLMK e a Hatch resultaram no prolongamento da vida útil de um alto-forno

Aug 17, 2017

By D. W. Fuerstenau

THE object of this article is to point out the experimental relationship which exists among contact angle, adsorption density, zeta potential, and flotation rate data. In each of the experiments discussed in this article, the surface properties of quartz, as a function of pH, were measured in solutions to which constant quantities of dodecylam-monium acetate were added. Morrow1 and deBruyn2 worked with solutions containing 4.08x10-5 moles per liter, whereas Fuerstenau3 and Seele worked with solutions containing exactly 4x105 moles per liter, but this difference is not significant. The pH of the solutions was regulated with HCI or NaOH in all cases. In each case, the addition of collector was constant, but the concentration of dodecylammonium ions decreased because of the formation of dodecylamine at higher pH values.2 Contact Angles: Gaudin and Morrow1 presented data for the contact angle of quartz in solutions containing 4.08x10-5 moles of dodecylammonium acetate per liter between pH 2 and pH 10.15. Using the same captive bubble techniques, the writer measured contact angles on quartz in solutions containing 4x105 moles of dodecylammonium acetate per liter at pH values ranging from 9.9 to 13.2. Both sets of data are presented in Fig. 1, in which the contact angle in degrees is plotted as a function of the pH of the solution. From pH 2 to about 8, the contact angle

Jan 1, 1958

By M. A. Vasina, I. A. Matveeva, E. A. Naumova, V. V. Doroshenko, N. A. Belov

"Using the calculated (Thermo-Calc software) and experimental methods (SEM, TEM, EMPA, DSC, XRD, etc.) the phase composition, structure and hardening of aluminium alloys of the Al-Ca-Zn-Mg system were studied in the following range: 2. 5%Mg, up to 10% Ca, and up to 14% Zn (wt%). Fragments of this quaternary phase diagram in the aluminium corner were constructed, including the liquidus surface, as well as some vertical sections. It was shown that the relatively large amount of zinc enters in the Ca-containing phase, which formula can be described as (Al,Zn)4Ca. An increase of Zn content leads to formation of Al4Ca primary crystals at lower concentrations of calcium. The eutectic (Al)+(Al,Zn)4Ca has a fine structure and aluminide particles are capable to spheroidization during the heat treatment at temperature 500 C. The maximal level of hardness observed on calcium containing alloys was higher than 200 HV, what gives the reason to expect good strength properties. With an example of an Al-9% Zn-2,5%Mg-3,5% Ca model experimental alloy based on the (Al)+(Al,Zn)4Ca eutectic, a principal possibility of manufacturing thin rolled sheets was demonstrated.INTRODUCTION Aluminum alloyed with calcium was first studied in 1970-80s by such authors as Piatti (1976), Moore (1978, 1980), Il'enko (1985), Swaminathan (1990), and Perez-Prado (1997) as superplastic materials. In particular, the alloy systems Al-Ca-Zn were studied (Il'enko, 1985, Swaminathan, 1990, Perez-Prado, 1997). For some time there was no new published works concerning the aluminum-calcium alloys. During the last years many works were published dedicated to the calcium alloying of magnesium alloys (Kim, 2011; Xu, 2011; Aljarrah, 2008; Bakhsheshi, 2014). This urged the authors (Belov, Naumova & Akopyan, 2016) to start studying cast and wrought aluminum-calcium alloys for construction (2008–2014). There is almost no information in the literature concerning triple and more complex diagrams of the aluminum-based system states with calcium and other elements. In recent work, parts of the state diagrams are plotted for the aluminum angle zone: Al-Ca-Mg-Sc (Belov, Naumova & Bazlova, 2016), Al-Ca-Ni-Sc (Belov, Naumova & Bazlova, 2017), Al-Ca-Si-Sc (Belov, Naumova & Akopyan, 2017) and others. Special attention was paid to the study of the system Al-Ca-Zn-Mg (Naumova, 2017). Based on this system creation of advanced extra-high tensile alloys is planned. Wrought extra-high tensile alloys series 7??? based on the system Al-Zn-Mg-Cu are well studied."

Jan 1, 2018

By Luc Delaey, Horace Pops

The structure and morphology of thermoelastic and burst type martensitic phases that form upon cooling in Cu-Zn-Si p phase alloys have been studied by transmission electron microscopy. The martensitic phases are composed of a lamellar mixture of two close-packed structures with different stacking sequence, namely ABCBCACAB (orthorhombic) and ABC (fcc). Striations within thermoelastic martensite are most likely produced during interaction with impinging burst-type martensite and not as a consequence of secondary shears. In a study of the martensitic transformation in ternary Cu-Zn based 0 phase alloys1 the dependence of the martensitic transformation temperature, M,, with composition shows variations for elements within a constant valence subgroup and between different subgroups. Such variations are not reflected in a change in habit plane, which is approximately the same for each ternary alloy, namely in the vicinity of (2, 11, 12 Ip. The fact that the habit plane remained constant, despite large differences in M, temperature and electron concentration, suggested2 that the crystal structures of the martensitic phases could be nearly the same. Crystal structures of ternary Cu-Zn based martensites have been determined recently for alloys containing the three-valent elements gallium3, 4 and aluminm. The present studies have been made to examine the structures and morphology of the martensitic phase in ternary Cu-Zn based alloys containing a four-valent element, silicon. I) PROCEDURE Two alloys were prepared by melting and casting weighed quantities of the component high-purity metals in sealed quartz tubes under half an atmosphere of argon. They were subsequently remelted by levitation under a protective atmosphere of argon. After allowing for losses of zinc as determined by the difference in weight before and after casting, the compositions in atomic percent of both alloys were established to be Cu-33.5 Zn-1.8 Si and Cu-27 Zn-5.0 Si. These alloys were homogenized in the P-phase field for 2 days at 800" C. Bulk samples consisted of a martensite phase at room temperature, the M, temperature being approximately 30' and 200" for the 1.8 and the 5 pct Si alloys, respectively. Thin disks were cut from the ingots using a spark machine, and they were heated for 5 min at 800' and quenched into water in order to obtain martensite. These slices were thinned chemically at room temperature in a solution consisting of 40 parts HN03, 50 part H3PO4, and 10 parts HC1 and thinned further electrolytically by the Window technique, using a voltage of 15 to 25 v and a mixture of 1 part HN03 and 2 parts methanol, which was kept at a temperature near -30° c. Foils were examined by transmission electron microscopy using a Philips EM 200 electron microscope. 11) RESULTS AND DISCUSSION 1) Structure and Morphology. Fig. 1 shows the martensitic phase in the alloy containing 1.8 at. pct Si. This phase is composed of contiguous platelets, each containing striations. The direction of the striations changes at the boundary between individual platelets. These internal markings resemble the striations that are usually identified as stacking faults, as for example in Cu-A1 martensites6-a or the lamellar mixture of two close-packed phases in Cu-Zn-Ga marten-sites.3p '9 lo In the present alloys, selected-area diffraction experiments have been obtained in order to determine the nature of the striations. Figs. 2(a), (61, and (c) are electron diffraction patterns of an area inside a single martensite plate. Fig. 2(a) contains diffraction spots which correspond to two close-packed structures with different stacking sequences, namely ABCBCACAB (orthorhombic) and ABC (fcc). Spots belonging only to the fcc structure are indicated by arrows. By tilting the foil either the orthorhombic structure, Fig. 2(b), or the cubic structure shown in Fig. 2(c) may be obtained. When the foil is oriented so that only the diffraction spots of the orthorhornbic structure are present, bright-field illumination shows small lamellae, as seen in Fig. 3. In this figure the lamellae that belong to the fcc structure are bright bands inside the dark extinction contours of the orthorhombic structure. The boundaries of the lamellae are parallel to the basal planes of the orthorhombic structure and to the {Ill} planes of the cubic structure, the close-packed directions of both structures being parallel. The 5 pct Si alloy shows similar features as those described for the 1.8 at. pct Si alloy.

Jan 1, 1969

By B. S. Tani, R. V. Schablaske, M. G. Chasanov

MEASUREMENTS of the solubility of scandium in liquid cadmium from 349" to 606°C by Chasanov, Hunt, Johnson, and eder' led to the isolation and characterization of the intermetallic compound ScCQ. The solid phase found in equilibrium with a saturated solution of scandium in liquid cadmium above 422°C is ScCQ. The equilibrium solid phase below this temperature has not as yet been characterized. Hexagonal needles of ScCG were isolated from a 5 wt pct Sc alloy which had been ice-quenched from 500°C. Free cadmium was leached away from the intermetallic with saturated ammonium nitrate solution. The concentration of cadmium in successive leaches was followed polarographically and the leaching process was terminated when the rate of cadmium dissolution decreased markedly. Chemical analysis of the intermetallic thus isolated is as follows: 11.5 wt pct Sc and 88.3 wt pct Cd. The composition of ScCQ is 11.8 wt pct Sc and 88.2 wt pct Cd. X-ray diffraction powder photographs of ScCds taken in a 114.6-mm Debye-Scherrer camera with CuKa, radiation can be indexed on the basis of a hexagonal nit cell. Lattice coonstants are a. = 6.330 ± 0.001A to 6.324 i 0.001A and co = 4.853 i 0.001A. The a0 has a slight range with the lower value seemingly associated with the cadmium-rich terminus of the phase. With eight atoms in the unit cell the calculated intermetallic density is 7.54 g per cu cm; the density as determined by a liquid-displacement method is 7.7 g per cu cm. Powder-diffraction data for ScCQ are recorded in Table I. Stoichiometry, symmetry, unit-cell dimensions, and the number of atoms per unit cell indicate the MgsCd (D019) type structure for ScCQ; space group is D,&-P6,/mmc. Atomic coordinates are:

Jan 1, 1964

By A. Anttila

The grinding mill is probably the most common unit operation used in mineral processing. There is, however, much which can still be done in the way of optimization. This paper discusses the results of a well controlled pilot scale test in which the performance of a tumbling mill with a conventional rubber lining equipped with lifter bars is compared to that with a smooth rubber lining of the magnetic type. The results indicate that the smooth lining is about 14 percent more effective with respect to energy consumption. By optimizing the size of the grinding media, the mill capacity can be increased in many grinding operations. In this specific case the -20 mm ball charge required 26 percent less grinding energy than one with a -30 mm ball charge. The energy savings can. in most cases, be converted to increased capacity. The wear of the grinding media is difficult to assess over a short period test but the results suggest it is somewhat less when a smooth lining is used. The wear of the linings has not been included in this study but it is generally accepted that the use of the magnetic lining reduces the lining costs dramatically. Computer simulation using the Millsoft code, developed by Mishra e.a. confirms and explains the increased effectiveness of comminution when smooth lining and smaller grinding balls are used.

Jan 1, 1998

By M. M. Fine

The results of tests on oxidized lead ores from two properties are reported in this paper. The investigation was on a small laboratory scale only; no pilot-plant tests were made. One sample, from the Magajupa Mining Co., near Duenweg, No., contained coarsely crystalline and disseminated galena and cerussite, so both tabling and flotation were considered in the beneficiation. By this treatment of an ore containing 11.5 percent lead, a recovery of 79.5 percent of the lead was made in a concentrate containing 73.3 percent lead.

Jan 1, 1948

By B. G. Klugh

In a paper before the Institute at Wilkes-Barre, Pa., June, 1911,' Mr. James Gayley discussed the application of this process to iron-bearing materials. The same author² described the results of operations at the plant at Birdsboro, Pa. The purpose of the present paper is to present further discussion of some techuical details involved in the operation of this plant, and of the theoretical and practical relations of this product to blast-furnace practice. Since Oct. 1, 1911, the Birdsboro plant has been in operation at the blast-furnace of the E. & G. Brooke Iron Co. The results have been highly satisfactory, although the material treated, being chiefly the flue-dust currently made by the furnace or taker] from the accumulated stock-pile, was excessively high, and yet not uniform, in carbon, so that the desirable control or regularity of the amount of fuel in the mixture treated could not be maintained. Nothing could more forcibly demonstrate the flexibility of the process than the fact that, under these conditions, the sinter produced was, in all cases, of excellent quality. The Dwight & Lloyd process, as such, slid its present highly-developed mechanical appliances were described by Mr. Gayley in the paper above mentioned. While the repetition of some particulars will be unavoidable in this paper, it will be confined to features bearing upon the metallurgical principles involved. According to the principle of the process, the finely-divided iron-bearing material to be sinterecl is intimately nlixed with

Jan 1, 1913

By Richard F. Hammen

Mineral extraction from sulfide ore deposits usually leads to the combined action of oxygen and water on the newly exposed ore. The result is acid mine drainage, a low pH solution of various metal sulfate salts and sulfuric acid. Paradoxically, the valuable metals dissolved in acid mine water are a liability because they are too toxic for discharge but too dilute to recover economically. The expense of compliance with water quality release standards has reduced the profitability of many mining operations. Solid phase extraction (SPE) columns have been developed to extract metals from acid mine water. These columns are designed to remove the toxic elements from water and recover the metals as purified fractions. This article describes the results of a Phase 1 bench-scale project to test the performance of the SPE columns. The tests were conducted with water collected from the abandoned Berkeley Pit copper mine in Butte, MT.

Jan 1, 1993

By Zhengde Pang, Xue-wei Lv, Guibao Qiu, Chenguang Bai, Zhiming Yan

As a result of the consumption and the rising cost of raw materials for ironmaking, steel producers have increased their utilization of low-cost, low-grade raw materials such as high alumina iron ore. The effect of Al2O3 and the Al2O3/SiO2 ratio on the viscosity, surface tension and sulfide capacity of the CaO–SiO2–Al2O3–MgO–TiO2 blast furnace slag system were studied in the present work. At a fixed CaO/SiO2 ratio of 1.20, 9 mass pct MgO, and 1 mass pct TiO2, the viscosity increases with an increase in Al2O3 content at a range of 16–24 mass pct, and decreases when the Al2O3 is higher than 24 mass pct. Increasing Al2O3/SiO2 from 0.47 to 0.92 causes a slight decrease in viscosity of the slags and has an opposite effect when Al 2O3/SiO2 is more than 0.92. The surface tension increases with increasing Al2O3 content at a fixed Al2O3 content and Al2O3/SiO2 at a fixed CaO content. The desulfurizing capacity decreases with increasing of Al2O3 content, while increases with increasing Al2O3/SiO2 at a fixed CaO content.

Mar 1, 2018

By B. S. Crocker

Introduction Pebble mill grinding can be defined as wet or dry grinding in a tumbling mill with pebbles used as grinding media instead of metal balls. To clarify the terminology, which may differ in the various mineral industries, it is essential to point out the differences between grinding with partially sized and carefully sized grinding media. When grinding with partially sized media (limited top size only), sizing is usually the setting of the primary crusher and there is no bottom sizing-all fines, chips, sand, and small sizes are included. This is often called run-of-mine or primary autogenous grinding. In this case the entire crusher discharge is fed into the mill and part of it becomes "charge" and the rest is "sand feed." When grinding with carefully sized media (i.e., media that is sized both at the top and bottom of the size range), no fines or chips should be present in the charge to the mill. This is pebble milling and the grinding media consists of ore, rock, Danish pebbles, gravel pebbles, or ceramic pebbles-media that is appreciably lighter than steel balls. The grind¬ing charge is fed to the mill to maintain a load and it does the grinding usually on a classified sand product of suitable size. If the grinding media is the same as the raw material being ground, this type of grinding is also called secondary autogenous grinding. Pebble milling was in common use in the gold mines of South Africa in the early 1900s. It is by far the oldest form of autogenous grinding. It may be used to grind crushed ores from a maximum size of about -% in. to all -10 µm. Pebble milling differs from "run of mine" grinding in many ways, but two big differences are: I) The ore itself is crushed to approximately t/4 in., or it may be further reduced to 8 or 10 mesh in a rod mill or fine crusher. 2) Then carefully screened ore of the correct size is placed in one or more stages of pebble mills to grind the ore to its desired final size. The media size is carefully selected to be the most efficient for the particular size reduction required in each stage. This is a precise practice, and pebble mills can be designed as easily and accu¬rately as can rod mills or ball mills by those skilled in the art. A pebble mill is a rotating cylinder in which the grinding media has been carefully sized for the job in hand. If the mill is doing coarse grinding, the media will be correspondingly large and the mill might be called a primary (or intermediate) pebble mill or a lump mill. If it is to do fine grinding, the media selected is proportionately smaller and the mill would be called a secondary or tertiary pebble mill. The media itself is normally rounded pebbles made from screened ore from the primary-crusher discharge. The charge could be rounded pebbles of the correct size removed from a primary autogenous mill, or the pebbles could be carefully sized gravel, sized beach pebbles, or sized flint pebbles. Usually the specific gravity of a pebble is from 35 to 55% of that of steel balls. It commonly varies from 2.66 to 4.2, depending on the specific gravity of the ore. Primary pebble mills, or lump mills, would be charged with pieces of rock up to 10 in. maximum and 5 in. minimum and would grind crusher discharge with a maximum size of 1/4 in. on hard ores and 3/8 in. on softer ores. Secondary pebble mills could be charged with pieces of rock screened on 4 x 4-in. square mesh and retained on 1 1/2 x 1 1/2 in. These mills would grind material with a top size of 8 to 10 mesh. Tertiary pebble mills could be charged with screened rock that would pass 3 x 3 in. and be retained on 1 x 1 in. and grind 35 to 48 mesh sands. Principles of Operation Media Size To operate a pebble mill efficiently it is imperative that great care be taken in screening the rock feed that is fed into the mill to round up into a range of pebble sizes that are suitable for grinding of the sands that are also being fed into the mill, having regard to the top size and the average size of such sands. Since most mill operators know from experience the correct size of steel balls to be used in a mill to handle different sizes of sand feed, it is convenient to relate the pebble size to a ball size. If the correct ball size is not known, it is relatively simple to conduct batch laboratory tests in 12- to 18-in. laboratory mills to determine the optimum size of steel ball. Also, Bond and others have published formulas for calculating the optimum ball size. When the correct size of the individual steel ball is known, then a pebble of the same weight will perform the same grinding if used in the proper size of mill and under the proper conditions, which will be defined later. This media size, as defined by the average weight of the individual pieces, is most important. The following tests will serve to clarify this point. Laboratory Tests Using Steel Balls or Pebbles. Several labora¬tory grinds were made to compare a given size and weight of steel ball with a pebble of the same weight but larger size, and of the same size but lighter weight. The following loads were used in the 12-in. laboratory mill: All 1 1/4-in. steel balls weighing 122 ± 10 g. All 1 3/4-in. pebbles weighing 123 ± 5 g. All 1 1/4-in. pebbles weighing 45 ± 3 g. To equalize capacity, the test with the steel balls was run only 34% as long as the tests with pebbles. In each case, 2,500 g of primary sands were ground at the optimum gravity for the media being tested at a speed 78 1/2 % of critical speed, and for 170, 340, and 680 revolu¬tions for the steel balls, and 500, 1,000, and 2,000 revolutions for the pebbles. The first test is summarized in Table 74 by showing the 80% passing size in microns for the feed and for each of the grinds. Two other tests are summarized in Table 75 showing the screen analyses

Jan 1, 1985

By A. L. Mular

"This paper summarizes the present-day usage of computers in the mining-metallurgical industry. The industry appears to be following a path taken by other industries in improving the operation of processing plants, production schedules, grade control and haulage performance. A reduction in the cost of computers and computing has been a significant factor.An attempt is made to forecast the future of computers in our industry. Such developments as time-sharing, mini-computers, and easy-to-understand process-oriented languages will lead to wider usage. Considerable strides have been made in the use of computers for laboratory data acquisition. In general, the implementation of new methods, new techniques and new equipment will require plant personnel to develop new skills. The universities are meeting this challenge by re-structuring curricula and offering special courses. Most vendors of computers already offer special courses within their own facilities at a customer's plant."

Jan 1, 1970

By John W. Walkiewicz

The U.S. Bureau of Mines has conducted studies to utilize rapid microwave heating to stress fracture ore samples. Iron ores containing hematite, magnetite, and goethite were subjected to microwave energy in batch operations at 3 kW and heated to average maximum temperatures between 840 and 940 °C. Standard Bond grindability tests showed that microwave heating reduced the work index of iron ores by 10 to 24 pct. In a microwave chamber designed to simulate a continuous throughput operation at 3 kW, the grindability of a taconite ore was improved by 13 pct at a bulk temperature of 197 °C. Because stress cracking occurred at a lower temperature, less energy was consumed. To further improve the economics of microwave fracturing, higher powers up to 16 kW were used to rapidly heat samples to relatively low temperatures in a continuous, belt-fed applicator. A significant improvement of grindability was obtained with a larger rod mill feed size in comparison to a minus 6-mesh Bond feed.

Jan 1, 2010

By Paulo Conceição, Carlos Sampaio, Carlos Petter, Ariane Kuerten

The Sensor Based-Sorting technology is an emerging technology applied in mineral separation and concentration. The technique consists in using a method known as Dual Energy X-ray Transmission sorting (DE-XRT). The particle's position over the conveyor belt was evaluated and, despite de variability of results, shows that there is no a position with greater accuracy on the sensor's reading. Results obtained indicated that DE-XRT sorting technology was able to significantly reduce the mass and the ash content of the ore feed, being an interesting option for reduction of costs and improvement of coal quality in beneficiation plants.

Oct 3, 2019

By C. R. Julian

THE large pyrites ore-bodies, the underground mining of which is to be described, are situated at Rio Tinto in the Province of Huelva in Southern Spain. The situation of the different ore-bodies with relation to one another is shown in Figure 1. It will be seen on the plan that the strike of the ore-bodies is approximately east and west. The geology of the district has been very fully described by Dr. D. Williams (1), so that for the purposes of this paper it will be sufficient to give briefly the salient features o each of the two larger ore-bodies which are being mined by underground methods at the present time. (a) San Dionisio.-This ore-body is the largest single deposit in Rio Tinto, having on its upper levels a length of 3,500 ft. On the upper levels the average width is approximately 200ft. but in places on the lower levels there is a width of 900ft. of un broken pyrites. Diamond-drill holes, without running out of ore, show the ore-body to persist to a depth of at least 1,600 ft. The ore-body in the upper part lies between slate and porphyry walls, but in depth is enclosed in porphyry walls. (b) South Lode.-Faulting is considered to be responsible for the break in the solid ore between South Lode and San Dionisio. On the upper levels, the South Lode ore-body has an unbroken length of 4,000 ft. The massive pyrites has a maximum width of 300ft. and an average of about 100 ft. Ore has been proved to a depth of 1,000 ft., at which depth the ore-body is much reduced both in length and breadth. This ore-body, to the depth at which it has been proved, lies entirely between slate and porphyry walls. The South Lode and the San Dionisio ore-bodies are mined both by open-cast and by underground methods. There is evidence that these mines have been exploited intermittently during the last 3,000 years; but, as is to be expected, no records are available of the tonnage mined prior to the time of purchase by the present company.

Jan 1, 1940

By Rodrigo Sales

Os principais objetivos de um projeto de Integração e Otimização de Processos (PIO – Process Integration and Optimisation) é de auxiliar no desenvolvimento de uma estratégia integrada de desmonte e cominuição que minimize o custo total por tonelada processada nas etapas de lavra e cominuição das operações, minimize o consumo de energia e maximize a taxa de processamento, produção de metais e lucro da empresa. O projeto consiste na revisão de práticas operacionais, auditoria e amostragem, benchmarking, modelagem e simulações das operações de perfuração e desmonte e cominuição. Isto permite uma análise holística das operações para identificar oportunidades de melhorias e desenvolver estratégias integradas e otimizadas de operação da mina-à-planta. O projeto incluiu o sistema exclusivo da Metso, SmartTag™, para rastrear o minério dos furos de desmonte na mina até a planta concentradora com o objetivo de correlacionar os tipos de minério e de desmonte com os resultados de desempenho da planta. O sistema de modelamento geometalúrgico automatizado chamado GeoMetso™ utiliza a tecnologia de rastreamento de minério SmartTag™ para coletar continuamente dados de desempenho da planta e atualizar automaticamente os modelos preditivos e o modelo de blocos em tempo real. Este sistema é a base para a implementação, validação e melhoria contínua das estratégias integradas e otimizadas de operação, além de auxiliar na reconciliação da mina-à-planta e planejamento de lavra.

Aug 17, 2017

By Luiz Guilherme Isfer Maciel, Marilena Cardu, Fernando Golin, Jacopo Seccatore

"This study applies the concept of the difficulty of tunnelling by drilling an blasting (D&B) to selectedcases from the Brazilian tunnelling industry. The difficulty of tunnelling has been defined in previouswork as the difference of specific drilling (SD) from industrial average trend: easier when SD is lowerthan average, more difficult when SD is higher than average. Results show how tunnels in Brazil tend tobe unrealistically more difficult to excavate when compared to similar excavations in similar geologies elsewhere in the world. It is thoroughly discussed the reason for such anomaly (up to +90% SD compared to industrial average). One reason could be the lack of options amongst explosive products on the brazilian market. Only ANFO and explosive emulsions are available in Brazil. Lacking high VOD(Velocity of Detonation) products might result in reducing the maximum allowable burden amongstproduction holes, therefore increasing SD. Another reason could be found in the tunnel designers’tendency of choosing D&B as excavation method for weak rock masses that would benefit from mechanical excavation. The reason to this tendency can be partly found in the lack of availability of mechanical excavation machines in the brazilian market. Blasting in weak rock masses requires more careful smooth blasting, hence a closer spacing amongst contour holes to avoid costly overbreak: this increases SD. A third reason could be found in the lack of skill amongst the local workforce. When dealing with unskilled workers the blast designers naturally tend to avoid highly optimized blasts thatrequire very skilled workforce to be realized on field. The designer in this case tends to leave the blastdesign simpler but more robust, at the cost of higher specific drilling and specific charge. The conclusions suggest that this unrealistic difficulty when compared to world average could be a simptom of the so-called “Brazilian cost” within the tunnelling industry."

Jan 1, 2017