Search Documents

By J. A. Fellows, Earnshaw Cook, H. S. Avery

THE increased use of heat-resistant alloys (26 per cent Cr, 12 per cent Ni; 16 per cent Cr, 35 per cent Ni; 12 per cent Cr, 60 per cent Ni; etc.) in recent years has been accompanied by continued demands by the consumer for improvement in properties. The manufacturers of these materials, of necessity, have resorted to more critical studies of the basic causes of variations in fundamental properties. To keep pace with the need for augmented information, previous techniques of investigation have been refined and new test methods and instruments created. It is the purpose of this paper to describe the apparatus, experimental technique and precision of measurement that were employed in the exploration of properties of heat-resistant alloy presented in a companion paper.? The detailed precautions in experimental procedure essential for attainment of accurate and comparable data at elevated temperatures cannot be too highly emphasized. THE CREEP TEST Since the fundamental concepts of creep testing have been recognized for the past 20 years, present interest is restricted to refinements in equipment and experimental procedure. The creep-test laboratory constructed for the American Brake Shoe and Foundry Co. is designed to permit 1000-hr. tests in the temperature range of 1200° to 2200°F. with a choice of applied stress extending from 50 to 50,000 lb. per sq. in. in increments of 50 lb. per sq. in. To simplify the calculation of weight combinations, the loading beams (Fig. I) are provided with counterweights to eliminate the tare. The precision of the knife-edges (10.1 ratio) is such that a 10-gram weight placed on the upper specimen grip will be exactly balanced by a 1-gram weight attached to the loading shackle. Check of the loading weights proved the maximum error to be 0.06 per cent. Axial alignment is provided by crossed knife-edges in the grip seats. The furnaces are similar in design to those of Crane and Company, Battelle Memorial Institute, and the U.S. Steel Corporation. An 80 per cent Pt, 20 per cent Rh No. 19 B. and S. gauge wire is used as the heating element. The details of construction are shown in the radiograph reproduced in Fig. 2. The windings are held in place on an alundum tube with alundum cement; the distribution of turns is adjusted to give a maximum temperature gradient of ± 1°F. over a 4-in. gauge length (Fig. 3). To avoid sharp temperature differentials at the ends of the test section, the length of the furnace is four times the gauge length. Sixteen-inch coupons are used to reduce the temperature of the threaded

Jan 1, 1942

By Zhucheng Huang, Yuanbo Zhang, Kecheng Zhang, Guanghui Li, Tao Jiang

"With rapid development of Iron and Steel industry, plenty of metallurgical dusts and sludges are generated, which have not been effectively utilized because of their poor hydrophilicity and bad ballability. Agglomeration and roasting of metallurgical dusts & sludges with a new-type composite binder are studied in this paper. The results indicate that the dosage of the new binders can be decreased to 2.5 wt% from 3.5 wt% when using the wet-grinding process. Under the optimal conditions of briquetting pressure 2070 N/cm2, briquetting moisture content 13 wt%, roasting temperature 1000 °C and roasting time 40 min, the qualities of the green, dry and roasted briquettes meet the requirements of the industry production. The finished products have the compression strength of more than 2000 N/cm2, which can be used as high-quality burdens for blast furnaces.IntroductionWith rapid development of Chinese Iron & Steel industry, there are more and more serious resource shortage and environmental pollution existing. Converter sludges, containing 30% ~ 40 wt% moistures, are typically difficult for recycling [1]. Foreign processing technologies for sludges treatment are relatively advanced including cold-bonded agglomerates for blast furnace, RHF reduction for the dusts and sludges with high content of Zn and Pb, smelting and reduction. Domestic iron and steel companies use a small amount of sludges in sintering. However, the sludges have the characteristics of high moisture and containing harmful impurities, which directly affect the sintering mixture permeability and product quality [2-5]. There are also other technologies such as production of metallized pellets, cooling agents for steelmaking, etc [6]. All of these deficiencies and applied are not in large-scale."

Jan 1, 2011

By Chris Rule

This paper tells the story of the rapid commercial application of stirred milling technology at Anglo American Platinum?s many Concentrators. The first stirred mill ? a 10 000 litre IsaMillTM; the largest at the time, was commissioned in late 2003. The project development work was presented at SAG 2001. This operation was ?proof of concept? and vindicated the decision to scale up the technology; allowing a rapid and extensive roll-out of mainstream regrind mills as well as several further flotation concentrate regrind mills, over the next six years. Currently 23 stirred mills are in operation with 64 MW of installed drive capacity ? this paper describes the projects? roll-out and the significant results achieved to date. Many operational problems have been solved along the way, some of these will be described. The introduction of the technology has seen a step change in metallurgical results and progressively decreasing operating costs.

Jan 1, 2012

By A. U. Miller

Since the organization of the Federal Bureau of Mines, part of the duties of the field men of the Safety Division has been to teach those connected with the minerals industries how to render the proper assistance to an injured worker between the time of the accident and the time when the injured receives medical attention--in other words, "first aid to the injured." For a number of years after the training was introduced, the response of mine officials and workers was very slow. Many times Bureau instructors devoted at least a week to training 5 to 15 or a few more men. However, in recent years since the companies and the Bureau of Mines have had an opportunity to study the results of first aid training, it has been found that in addition to taking care of an injured worker after an accident and thereby greatly reducing the severity rate, the tendency is for the majority of those who take the training to be more careful in their work, or to be more "safety conscious."

Jan 1, 1938

By Guo Qian, Du Guangyin, Deng Yongfeng, Liu Songyu, Wang Ningping

"Metakaolin (MK) can efficiently enhance the strength and the impermeability of concretes and mortars. However, it has rarely been attempted in admixtures of cement-stabilized soils until presently. As deep mixing method is wildly used in ground improvement, the strength of cemented soils (soilcrete) and the applicability of the MK should be considered. This paper focuses on the macro-strength development of cement-stabilised silty soil mixed with MK. The result shows that the addition of MK can enhance the unconfined compressive strength of the soilcrete, which attributes to a combination of the rates of OPC hydration and the MK-CH reaction. Note that the strength of soilcrete was influenced by the properties of soil, water-to-binder mass ratio (W/B) in admixtures, which needs to be reconsidered since the binder mass composes that of cement and MK totally.INTRODUCTIONCement was used in ground modification techniques, such as the jet grouting, deep mixing method (DMM) which was put into practices in Japan and Nordic countries in the middle of the 1970s, and then spread to China, South East Asia[1]. For last decades, fly ash, slag or silica fume was mixed with cement to form the new cement base stabilizing agent in the view of economy and performance improvement. The mechanical behavior of these soil-binder admixtures (nominated as “soilcrete”), was investigated. But the soilcrete modified with the metakaolin (MK) was still not investigated much and lots of further work needs to be conducted.Some laboratory experiments of the soilcretes modified with MK have been taken[2~4]. Kolovos et al. (2013) indicates that the unconfined compressive strength has a more significant improvement when W/B equals 0.4 than that when W/B equals 1.20 concerning the water-to-binder mass ratio (W/B). Sonebi et al. (2013) investigates the mechanical behaviors of cement grouting containing MK with W/B equals 0.4, and also found the effectiveness of the addition of MK. Zhang et al. (2014) performed the studies on Lianyungang marine clay improvement showed that MK obviously enhanced the quality of cemented soils.In this paper, the strength of soilcrete modified with MK is further investigated, where the unconfined compressive strength at different curing time, the content of MK and cement (w/w) in lab conditions was discussed."

Jan 1, 2015

By Saulo Brinco Diniz

O presente trabalho buscou explorar a influência de um tratamento térmico de ressolubilização (70 minutos / 510ºC), antes da laminação convencional de uma liga de alumínio 7475-T7351. Para tal, duas amostras (com e sem o tratamento térmico) foram laminadas de 12,5 mm até 3 mm de espessura, após 13 passes com uma redução aproximada de 10% por passe. Com base nos resultados obtidos via microscopia óptica (Olympus, modelo GX51) e dureza Vickers (durômetro EMCOTEST, modelo Duravision 300), conclui-se que o tratamento térmico de ressolubilização adotado antes da laminação convencional da liga em estudo, propiciou modificações microestruturais e incremento na dureza quando comparada a amostra laminada sem prévio tratamento térmico de ressolubilização.

Aug 17, 2017

By Katarína Gáborová, Marcela Achimovičová, María Florencia Márquez‑Zavalía, Jaroslav Briančin, Oľga Šestinová, Pavel Škácha

In this paper, the structure, morphology, chemical composition and leaching of naumannite ( Ag2Se) were studied. Mechanical activation of Ag2Se in a planetary ball mill resulted in increasing its specific surface area. The influence of milling time on the particle size was studied by particle size distribution analysis and scanning electron microscopy. The leaching kinetics of non-activated and mechanically activated samples in 3.5–7.9 mol/L HNO3 solutions were examined. Subsequently, the effect of leaching temperature in the range of 25–50°C on the recovery of silver from mechanically activated naumannite was documented. The maximum yield of silver 94% was achieved after 120 min of leaching in 7.9 mol/L HNO3 at 50°C for the sample mechanically activated for 30 min. Based on calculated activation energy values from the Arrhenius equation, a mixed leaching mechanism consisting of diffusion and surface chemical reaction as the rate-controlling steps of the solidliquid reaction was assessed.

Mar 4, 2023

By Freeman Bishop

More than a few discussions are taking place these days among management economists seeking a way out of the dilemma of lower productivity vs. higher labor costs. Most suggestions would be illegal under present antitrust laws. Otherwise interindustry cooperation could be used to divide up some of management's tasks. Or price structures might be tuned to the special machinery and skills of some plants. Both remedies would be under attack almost immediately. There is one other remedy that is getting lots of attention: some form of compromise between management and labor to phase out no longer needed work practices that unions insist shall be retained. Railroads are the national industry suffering the most from this disease, still known as "featherbedding," an epithet coined by the railroaders themselves.

Jan 1, 1971

By Peter G. Chamberlain

Domestic mining will not produce a significant portion of the manganese consumed in the United States unless new mining and processing techniques are implemented that will enable domestic lean ores to economically compete with rich foreign ores. One mining-processing technique that appears promising for certain deposits is in situ and/or heap leaching with aqueous SO2. Since leaching offers economic advantages of low capital costs, low operating costs, and short start-up times as well as environmental and safety improvements over conventional mining-processing, the Bureau of Mines studied the leachability of manganese deposits from several districts. Manganese oxides, hydroxides, and carbonates were leached to 80 to 90 pct recovery in 7 to 40 days of leaching with a solution containing 5 pct SO2 in column leaching tests. Preliminary cost analyses of surface mining-heap leaching, block caving-in situ leaching, and shrinkage stoping-in situ leaching indicate that the products of manganese leaching may be economically produced for the chemical and electrolytic manganese industries. The easiest marketable product to obtain would be a manganese sulfate commonly used as a fertilizer amendment. Manganese carbonates and hydroxides could also be precipitated from the pregnant leach solutions.

Jan 1, 1983

By W. P. Sykes

SINCE Honda and Murakami1 in 1918 proposed their constitutional diagram of the carbon-free iron-tungsten system, considerable effort has been expended by several investigators in attempts to define more positively the structural features of the alloys. The existence of an intermediate phase corresponding to the formula Fe3W2 (68.7 per cent W) was proposed from evidence of a purely metallographic nature by one of the present authors2 in 1926. Since that time the identity of this phase has been confirmed by Arnfelt3 and by Takeda,4 both of whom employed X-ray methods as well as the microscope and the chemical analysis of isolated microconstituents. According to Arnfelt, Fe3W2, as crystallized from the iron-rich melts at a temperature above 1450'C., contains by analysis 68.7 per cent W. The lattice of this phase is characterized by trigonal symmetry. Arnfelt, moreover, proposed a second intermediate phase formed at some temperature between 1450° and 1000° C. by a peritectoid reaction involving Fe3W2 and the iron-rich solid solution. A melt containing 25 per cent W was cooled to 1000° C. and heated for. 100 hr. The precipitated tungsten-rich constituent was separated and found by analysis to contain 62.6 per cent W. This composition agrees closely with that represented by the formula Fe2W (62.2 per cent W). Diffraction patterns from the concentrated precipitate showed a hexagonal unit cell. Takeda confirmed the data of Arnfelt regarding Fe3W2 but was unable to detect Arnfelt's second intermediate phase. While Takeda. failed to describe in detail the treatments employed, he stated that in alloys containing 40 per cent W which were quenched after heating at various temperatures between 1200° and 1450° C., no evidence of the second phase (Fe2W) was observed either in the microstructure or in the diffraction patterns of isolated residues. He therefore considered the existence of this low-temperature hexagonal compound as disproved.

Jan 1, 1932

By John Convey

This short paper deals with the subject of research and its relation to productivity. All who have stopped to even think about industrial re-search and its impact on the nation-al economy take for granted that research and development are pre-requisite to increased productivity. It is another matter, however, to identify and properly evaluate the many factors entering into the relationship between the two. Some studies are currently underway in the United States on the subject, but, so far, nothing much in the way of conclusive data has come to light. In Canada, we have not yet even produced any statistical figures on national productivity, although work is now being done on this subject and information will soon be available. The usefulness of being able to measure the benefits of investment in re-search and development in terms of industrial growth or productivity need not be laboured for the benefit of those interested in research management.

Jan 1, 1964

By T Barnes, K D. Sexton, T J. Tope

For the past decade, the U.S. Department of Defense (DoD) has been under increasing pressure from state and federal regulatory authorities to develop management strategies for waste streams generated at its bases, installations, and ranges. Since passage of the Federal Facilities Compliance Act (FFCA) in 1992, concerns have focused in particular on military munitions and energetic waste streams.

Jan 1, 1997

By Zhucheng Huang, Lingyun Yi, Bin Chai, Tao Jiang

"A high iron content manganese ore was reduced at 900~1200°C and followed by a magnetic separation process. SEM and EDS analyzes were employed to examine the transformation of microstructure and phase in reduced sample and the mechanism was revealed. Results showed that elements enriched during reduction. Iron existed in the metal iron phase and most of oxygen formed compound with manganese. Consequently a clear distinguish between iron phase and manganese minerals formed, which was beneficial to the separation of iron and manganese. But the iron phase can not be monomer dissociation in grinding process and manganese compounds turned into magnetic product as package and mechanic inclusion due to the isomorphism of iron and manganese and the small particle size. And MnO could be found partially in iron phase, which hindered the further separation of manganese and iron.IntroductionManganese is widely used in industry. The amount of manganese used in steel industry is very huge and 90% manganese is used in steel industry. Manganese ore resources are rich in China, yet with fewer rich ore but more low-grade ore which accounts for 93.6% and fine refractory ore. The constitution of the ore is very complex and more than 73% of all the manganese ore contains iron[l,2]. With the increasing of consumption of steel, the demand for manganese is becoming larger and larger and the imported ore accounts for more than 50%. Therefore, how to use the manganese ore efficiently has very significant meaning. The main method is manganese residual, which is simple and stable. However, the development of the method is limited by the quality of manganese ore, the huge amount of manganese residual, the technology of blast furnace process and economics[3,4]. Chemical benefication which may pollute environment and is difficult to recover iron is still being researched[5,6]. The paper investigated the process in which anthracite coal was the reducing agent for coal-based direct reduction and magnetic separation of the ore, and SEM with EDS measurements were employed to examine the transformation of phase in reduced sample and the mechanism was revealed[7,8]."

Jan 1, 2013

By Bin Xu, Qian Li, Xin Min, Xiaoliang Liu, Yongbin Yang, Tao Jiang, Yan Zhang

The ringing characteristics of acid and alkaline iron ore pellets powder in kiln were studied by the thermodynamic calculation using software FactSage7.0, roasting experiments using briquetting method and analysis of SEM-EDS. The thermodynamic calculation demonstrated that liquid phase could be generated from alkaline pellets powder at a lower temperature and the amount of formed liquid phase was much more than that from acid pellets powder at the same temperature. Roasting experiments indicated that the compression strength of alkaline pellets powder briquettes were also higher than that of acid pellets powder briquettes. Additionally, the analysis of SEM-EDS suggested that the alkaline pellets powder briquette presented more liquid phase and a more compact structure comparing with the acid pellets powder briquette, which was consistent with the results of thermodynamic calculation and roasting experiments. Hence, in comparison with acid pellets powder, alkaline pellets powder is much easier to ring in the kiln.

Mar 1, 2017

By James T. Tanner

Mica is a generic term that applies to a group of complex aluminosilicate minerals that have a sheet or plate-like structure and with different chemical compositions and physical properties. All micas form flat six-sided monoclinic crystals with remarkable cleavage parallel to the direction of the large surfaces, which permits them to be split into optically flat films; as thin as 1µm in thickness in some cases (Rajgarhia, 1987). Some micas are more easily split than others. For example, muscovite mica found in pegmatites is more easily split into thin films than is phlogopite. Mica found in mica schist is not as easily delaminated as mica found in weathered pegmatites. According to Dawson (1 949), the commercially important mica minerals are: Muscovite-potassium mica (colorless to pale green and ruby) Biotite-magnesium-iron mica (dark brown to black) Phlogopite-magnesium mica (pale yellow to dark brown) Vermiculite-hydrated biotite or magnesium-iron-mica (bronze yellow flakes) Lepidolite-potassium-lithium mica (pale lilac to deep purple) Some micas of less importance are: Zinnwaldite-lithium-iron mica (gray to smoky brown) Roscoelite-vanadium-potassium-magnesium mica (various shades of green and brown) Mica, principally muscovite, is widely used for industrial applications because of its exceptional physical, chemical, electrical, thermal, and mechanical properties (Table 1). Phlogopite and vermiculite follow muscovite in importance. Biotite finds very little commercial application at the present time. Commercially, mica is used in a number of forms. These forms and their description follow: Sheet mica refers to books of mica either mined from hard rock (pegmatites) or from loosely consolidated clayey material formed from the weathering of pegmatites and alaskites. These books can be readily split into thin film or splittings with specific thicknesses ranging from 0.0031 to 0.10 mm (Davis, 1985). Quality sheet mica is graded into 10 quality classifications (Tables 2 and 3). Books of mica that are flawed with excess inclusions, cracks, or folds (A mica) are called scrap mica and are either ground into commercial products by a dry or wet process. Built-up mica was developed in 1894 as a result of the cost and scarcity of sheet mica, and because many satisfactory electrical parts could be made from it (Preston, 1971). This type mica is formed by layering pieces of mica splittings upon one another and binding them together with inorganic or organic binders. These sheets are then pressed together under high temperature. Mica for this process is produced from pieces of sheet mica too small to be punched into electrical parts (Davis, 1985). Reconstituted mica is mica paper produced by forming a mat of very thin delaminated flakes of scrap mica. This mat is usually impregnated with an organic binder, but is also available unimpregnated. It is dried at 110°C. The mica for this process is either produced from the trimmings of a sheet mica operation or from blocks of A type mica (Davis, 1985, Chapman, 1983). Ground mica constitutes by far the largest use of mica, both quantitatively and application wise. It is produced by grinding and sizing scrap mica (also mica concentrate) obtained from five sources, 1) trimming from sheet mica, 2) A type mica blocks, 3) as a byproduct of spodumene and feldspar mining, 4) weathered pegmatites and alaskites, and 5) metamorphic schists. Synthetic mica is produced by crystal growth in a slowly cooled melt of accurately proportioned chemical oxides. Extended cooling times at a specific viscosity result in larger crystals. Many different micas have been formed by this process; however, fluorophlogopite is the most common.

Jan 1, 1994

By J. Rostami, J. Brune, S. Slouka

Respirable dust poses long-term health issues to personnel working in mining and civil projects where mechanized mining and tunneling machines are used for hard rock excavation. Machines, such as longwall shearers, roadheaders, or continuous miners, use consumable picks to cut rock. However, rock dust is generated in the work environment each time the pick tip contacts the rock surface. Additionally, the generated dust can be reintroduced into the air further down in production, such as at transfer points. The purpose of this study is to characterize respirable dust particles generated at the pick tip at two stages of pick wear: new and moderately worn. Understanding dust characteristics in terms of concentration, size distribution, and particle shape throughout the life-cycle of the pick will provide a basis to mine and tunnel operators for changing out picks to mitigate dust generation at the source. This paper discusses the dust characteristics generated from preliminary full-scale cutting tests in a laboratory of an igneous rock block cut with conical picks at new and moderately worn levels of wear. The moderately worn pick generated a size distribution that favored smaller particle sizes compared to the new pick. The moderately worn pick also generated more overall dust, as the concentration level in mg/m3 was over double the amount of the new pick. Lastly, both picks generated particles that had similar aspect ratios and roundness measures.

May 18, 2022

By U. M. J. Boin, W. L. Dalmijn, T. P. R. de Jong

"This paper explores the complex interrelationship between the resource cycle, recycling and metal production as a function of economics, environmental legislation, and product design. It is argued that central to optimising this resource cycle lies the control in particular of physical separation plants by the application of advanced sensor technology and sorting equipment, as well as suitable control and sampling algorithms supported by optimising mass balance models.Metals are produced through a long chain of processes. For primary resources, metals production goes through mining, mineral processing, ore smelting, conversion and refining steps or via low temperature hydrometallurgical processes, or a combination of both pyro- and hydrometallurgical operations. For the recycling of resources, metals are separated and recovered from metal scrap, which plays an increasingly important role in the world. Metals after being produced, either from primary or recycling resources, have to be further refined or manufactured into various types of alloys and finally shaped into different products for the end-users. Since the end-user discards products the contained materials find their way back into the resource cycle as scrap. Therefore, controlling the metallurgical reactors also controls, in a much broader sense, the material quality in the complete metals cycle, from the production phase, to the end-use phase, up to the recycling phase (Reuter et al., 2003). The recycling phase includes separation of materials into saleable intermediate products, which are reintroduced into the production phase as a recycling resource. Therefore, the metallurgical processes in each unit operation in the metals production and processing chain have to be controlled, so as to achieve optimal performance of high product quality, low energy and materials consumption, and low environmental impact."

Jan 1, 2003

By B. Y. Tuo

This article presents results of studies performed to determine the feasibility of using low-grade limonite ores from Yunnan deposit. Laboratory tests and commercial trials have shown that the magnetic separation can be performed with a high high-grade concentrates. The quality of the preparation concentration meets the requirements for blast-furnace smelting. The results as a whole demonstrate the feasibility of utilizing bank limonite ore. Yunnan limonite?s magnetic separation, roasting magnetic separation and flotation experimental study shows that grade of the ore grade can been from 32.91% heighten to 58.64%, a recovery of iron is 90.87%, productive rate is 51% through orthogonal test optimization; roasting magnetic separation can obtain that the grade of iron preparation concentrate is 61.16%, recovery is 67.39%, productive rate is 36%. As far as economy and enviormental protection is concerned, strong mag-netic suggested a more appropriate process. Keywords: Limonite; Roast; Magnetic separation

Jan 1, 2014

By T. Bhambhani, Mukund Vasudevan, Partha Patra, D. R. Nagaraj, P. Somasundaram

Selective Ni separation from ultramafic ores rich in serpentines has been a huge challenge in the mineral processing industry, and therefore highly inefficient. Analysis of the root causes of the challenges and consequent development of robust processing solutions were the main goals of the Cytec-Columbia. University-Vale Joint Development Program. In this context, the subject of this paper is limited to one of the key findings of this research program which is the influence of fibrous serpentines on grade-recovery characteristics. Specifically, the poor flotation behavior is characterized by an atypical reverse C-shaped grade-recovery curve.

Jan 1, 2011

By Milton H. Fies

THE writer wishes to acknowledge at the outset his great sense of obligation to those who contributed so broadly and expertly to the preparation of this paper: Dr. Albert DeSmaele, Chairman of the Board of Directors of Socogaz, Belgium; Dr. Julien Venter, Director of the National Institute of Coal Mining and Coal Utilization Industry, Belgium; Dr. Roger Loison, Chief Engineer, French National Coal Research Board, France; and Dr. Erich Sarapuu of the Sinclair Coal Co., Kansas City, Missouri. Liberal use has been made in this paper of a recent publication on Russian, Italian, Belgian, and French experiments prepared jointly by the Centre d'Etudes et Recherches des Charbonnages de France (Cerchar) and the Institut National de l'Industrie Charbonnière of Belgium (Inichar).1 The writer is particularly indebted to Dr. E. T. Wilkins, of the Fuel Re¬search Station, London, and to Mr. James L. Elder, of the Alabama Under¬ground Gasification Experiment at Gorgas, Alabama, for their unfailing patience and effective support. Not only did these experienced and capable men edit and revise this discussion, but much of its content is a direct con¬tribution quoted in full from their memoranda. Without the assistance of all these colleagues, this presentation would not have been possible. It has been a privilege to serve and work with them and to acknowledge repeatedly their loyal cooperation. The recovery of the energy inherent in coal beds throughout the world has been done through the years by methods that today may be justly regarded as primitive. While the techniques of coal mining through the application of machines and the enhancement of information and skills have advanced to an extraordinary extent, particularly during the past 20 years, the underlying means is essentially the same as when man first began to mine coal. Despite this progress in the manner of coal mining, it continues today as a hazardous, toilsome, grimy task. Coal mining per se has advanced at a greater and more rapid stride in the past 25 years than the mining of any: other mineral, but the basic method is fundamentally the same as it was the first day a miner took a pick into his hands many centuries ago. This situation presents a challenge to mining engineers everywhere, from

Jan 1, 1953