Search Documents

By P. H. Williams, D. J. Morris

The co-disposal of coarse and fine coal wastes by combined pumping through a pipeline to subaerial deposition was pioneered in Australia in 1990 by Jeebropilly colliery in Queensland. Significant segregation of fines is found to occur in its co-disposal delta, leading to the formation of distinct mainly coarse upper and fine-dominated lower segments; the upper delta drains rapidly and is able to support traffic on its surface immediately after deposition. An existing theory of subaerial deposition, originally developed for mine tailings alone and later extended to trial co-disposal, is shown to apply also to the upper segment of the full-scale Jeebropilly delta

Jun 19, 1905

By Tianjiao Luo

Some literatures discussed on how to recycle the various reagent, but the discussion on how to reuse the waste liquid directly is very little. How to reuse the waste liquid directly was researched in this paper. Firstly, the waste liquid should be filtrated to remove the impurity; then some quantity of H2O2 solution was dripped into the waste liquid to pretreat it; finally, CuSO4solution was added into the treated waste liquid and the pH was adjusted to about 12, then some HCHO solution was added into the waste liquid, in which the treated carbon fiber can be plated. The morphology and composition of coatings were investigated by means of Scanning Electron Microscopy (SEM) and Energy Dispersive X-ray Spectroscopy (EDS), the deposition rate was mensurated by the way of dissolution. The results indicated that, the plating effect was basically identical with new plating solution, and the solution is stable, and the plating rate is still about 0.8µm/h, and the copper coating is even and combines closely with carbon fiber. According to this way, the waste liquid can be reuse 5~7 times.

Jan 1, 2006

By Armstrong M

The Coal Mining Engineering Branch of the New South Wales (NSW) Department of Mineral Resources, in its continuing effort to improve coal recovery from underground coal mining operations, has undertaken a study of the mechanics of sub-surface deformation caused by caving of the extracted area behind retreating longwall faces. The strata movement was monitored by a multi-wire borehole instrumentation system consisting of mechanical anchors installed at different horizons in a borehole extending from the surface to the coal seam. The mechanical anchors were connected to the suspended weights on the surface by stainless steel multi-strand wires. The movement of these weights was monitored as the longwall face approached and retreated past the borehole. The anchors started subsiding as soon as the face retreated past the borehole and continued to subside until the subsidence levelled off when the face retreated 900 m past the borehole. The zone of major caving and bed separation extended to roughly 10 to 13 times the extracted seam thickness and high tensile strains developed inthis zone. The bulking factor of broken strata was less than 1.14 which indicated that the roof layers collapsed in big blocks. The goaf compaction was almost complete when the face retreat was 200 m. Low tensile strains prevailed in the strata overlying the zone of caving and bed separation.

Jan 1, 1986

By Richard F. Lynch, Frank E. Goodwin

"The development of Galfan, a new generation 95% zinc-5% aluminum-mischmetal alloy coating for steel, offers opportunities for greater fabrication flexibility and upgraded corrosion performance in automotive applications. The formability of Galfan is equivalent to that of electrogalvanized steel, based on laboratory tests and automotive component fabrication. Corrosion resistance of Galfan exceeds that of hot dip and electrogalvanized, including performance in automotive industry tests. Automotive production applications for deep drawn and stamped components in France and Germany are based on the ability to meet dual performance requirements for upgraded formability and corrosion resistance. The first U.S. Galfan application was on 1985 model Ford cars and light trucks for transmission oil cooler lines which has now expanded into a number of power steering tubing uses. IntroductionContinuing requirements for improved vehicle performance coupled with the ever present need for reduced cost have spawned the development of a number of new coated steel products. Among this new generation of coated steels is Gaifan™, a 95070 zinc-Solo aluminum-mischmetal hot dip alloy coating. Galfan exhibits particular promise for automotive use based on broad fabrication advantages and upgraded product performance(I ),The unique characteristic of Galfan is the key combination of greatly improved formability with much longer corrosion life. Galfan provides significantly better formability than any other hot dip coating. Testing shows that formability is limited primarily by the steel substrate to which the Galfan coating is applied. Galfan exhibits excellent resistance to flaking and microcracking during commercial forming operations. The result is the elimination of unnoticed damage to the coating which would show up later as premature rusting on the finished product."

Jan 1, 1987

By Pierre De Pasquale, Aquilino Antonio Alvarez-Castro

Greenhouse gas emissions are now an essential issue for extractive industries. Actually, lowering of quarry energy consumption and CO2 emissions participates to answer both environmental and financial issues. The “EE-Quarry” European project, supported by the European Commission (EE stands for Energy Efficient), develops a new and highly effective modelling and monitoring Energy Management System technique to improve Energy Efficiency and move to a low CO2 emission rate in the nonmetallic mineral industry.

Jan 1, 2016

By Howard P. Hamlin

This Bureau of Mines report is concerned with the testing procedures for evaluating clays, shales, and slates for lightweight aggregates using the rotary-kiln method of production. To meet the increasing demand for light-weight concrete, rapid, accurate methods for appraising raw materials for light-weight aggregate are needed. Preliminary tests were made on samples of clay, shale, and slate, using laboratory equipment, and the data were used to establish operating conditions for pilot-plant-size rotary-kiln tests. Lightweight concrete was made from the processed aggregates and the properties determined. The results show that the laboratory data can be used to guide rotary-kiln testing, and, with the exception of sampling, a complete appraisal of a raw material for lightweight aggregate concrete can be made in 3 days by the methods described in this report.

Jan 1, 1962

By Brain E. Gombos

The Allen Park Sanitary Sewer Overflow (SSO) Tunnel and relief sewer project, located in the city of Allen Park, MI, is a long-term corrective action designed to bring Sanitary District One?s sanitary system into compliance with its 2005 consent order and service contract with the Detroit Water and Sewerage Department (DWSD). The $20 million project is intended to reduce Allen Park?s wet weather discharges to DWSD, reduce bypass pumping to the Ecorse Creek and limit the future risk of basement flooding by providing storage during wet weather events and eliminating hydraulic bottlenecks in the sanitary sewer system.

Jan 1, 2013

By Mina M. Shinouda

Brightwater West (BT4) represents the state of the art in utility tunneling, namely a long relatively small diameter, soft ground tunnel, with no intermediate shafts, under significant groundwater pressures, requiring very precise survey control in order to hit a small exit window. The tunnel is over 6.4 km (4 miles) in length, is expected to encounter active earth pressures of over 5 bars in glacial geology, and a planned hole through into a shaft eye constructed at 45.7 meter (150 feet) below the water table. Despite the fact that all of these challenges have been previously overcome in larger diameter tunnels, the technical solutions are much more challenging in a smaller diameter due to the lack of space available for implementing the equipment and techniques required. In addition to the technical challenges, the project is faced with many of the constraints designed to minimize the impact of these types of projects on the neighboring community and environment. The work shaft for BT4 is within 15.2 m (50 feet) of Puget Sound and is on a site that was previously occupied by petroleum storage tanks, and all of the tunnel muck has to be removed from the site by barge as trucking is not allowed by contract. The paper addresses the work performed during the preparation for tunneling stage of this project both in assembling the TBM and in preparing the site for its arrival.

By J. Daavittila, P. Jokinen, M. Honkaniemi

In the latter part of the 1980?s Outokumpu Chrome in Tornio, Finland, was in a situation when its twenty-year-old ferrochrome plant was becoming inefficient to sustain economically sound production. The company made extensive studies on the then available processing methods to find out the best possible processing route. As a result the whole plant was practically rebuilt and expanded. When equipment was proven in practical operation an application for FeMn production was developed. Now when Tornio FeCr-plant is considering the expansion the same type of exercise is to be performed with today?s challenges, which will be discussed in the paper. These challenges include increasing costs or decreasing quality of raw materials, increasing energy costs, stricter environmental regulations and demand of better working conditions. The possibilities to respond to these challenges will be discussed in the paper. The future and continuing development with FeCr includes the better utilization of process dusts and a lower consumption of energy. By adapting the latest automation tools to better control of the process even higher efficiencies can be achieved with present technology. New processes are considered for development in the future and some possible technologies will be described.

Jan 1, 2004

By Juan Kobashicawa, Bernardo Falcón

En este trabajo se explican los controles automáticos desarrollados (In-House) e implementados en el circuito de Molienda de Compañía Minera Antamina, el cual abarca Molinos SAG, de Bolas y los Hidrociclones respectivos. Los controles implementados son basados en el Control por Lógica Fuzzy y las Bandas de Bollinger; así mismo se indican los criterios en el diseño de los controladores y las variables del proceso que se han tomado para la implementación donde se controla un indicador de distancia del centro de masa de la carga respecto al centro del molino de Bolas. Asimismo, se muestra el impacto positivo logrado con la estabilización del circuito.

Sep 1, 2017

This paper describes new research and development currently being undertaken by the CSIRO Mining Technology Group to advance the automation capability of continuous mining equipment in underground coal mining operations. The effort aims at increasing the overall rate of roadway development as well as providing a safer working environment for underground mine personnel. The activity is funded by the Australian Coal Association Research Program (ACARP) and forms part of a larger underground development initiative, known as the CM2010 project. The CM2010 is managed via a consortium of leading mining industry representatives through the Roadway Development Task Group (RDTG). The Task Group has identified three research areas requiring new development in order to realise the CM2010 project objectives: self-guiding (autonomous) continuous miner capability, an enhanced drilling and bolting process and improved mesh deployment. CSIRO's primary role in the CM2010 project is in the development of the autonomous continuous miner guidance capability.This paper reports on outcomes achieved at the half-way mark of a three year research and development project. It details the technical developments undertaken towards demonstration of a 'self-steering' capability to enable a continuous miner to automatically maintain a given mining heading and mining horizon under production conditions. A primary technical requirement of this automated functionality is the means to accurately determine both the location and orientation of the continuous miner in real-time. Testing and validation of the guidance system solution has been implemented using a combination of an instrumentation-grade inertial navigation unit and radar technology. Comprehensive performance evaluations have been conducted using a scale skid-steer mobility platform known as the Phoenix. Results achieved to the present stage of the project are highly promising and suggest that an automated self-steering functionality is achievable under production conditions. This new outcome represents an important move towards implementing a step change improvement for future underground roadway development.

Dec 6, 2010

By D. M. Doyle

A study of the various components contributing to energy costs and their relationships to generally trended operating data, such as tonnage, operating costs, etc., over progressively shorter time periods provides information for an energy audit. A study of annual data gives some insight into the importance of various energy components. As the time frame of the study progresses through monthly, daily and, finally, into quarter hourly data, the variations become more evident and, most important, strategies develop to minimize energy costs. The results of an audit conducted during the summer of 1978 at Wesfrob Mines Limited are reported to illustrate this important phase, prerequisite to a meaningful energy cost avoidance program. The balance of the paper deals with the energy conservation program at Falconbridge Nickel Mines Limited's Sudbury operations, the metering and control equipment, the commitment, the new energy accounting practices and, lastly, the policies. Examples of successful energy conservation endeavours include automatic peak electrical load control, waste heat recovery from mine air and compressor cooling water, energy reductions resulting from lower building temperatures and curtailment of idling loads. The use of pulse meters to measure the flow of gas, steam, compressed air and electrical energy, with their signals interfaced to process computers, allows monthly, daily and, if necessary, immediate reporting of energy and energy per unit of production information The program so reported at Falconbridge's Sudbury Operations is credited with an annual cost avoidance of .9 million dollars in a 14.0-million-dollar annual energy account

Jan 1, 1979

By M. J. Leeuwner

Computational fluid dynamic (CFD) modelling is used to research the complex flow structures that exist in a hydrocyclone. By simulation of a two phase (water and air) flow system, the internal flow and multiphase interactions are investigated. The suitability of CFD modelling as a design tool is further evaluated by examining the effect of varying device dimensions. Three hydrocyclone geometries, used in previous studies, are specified. A transient simulation approach, which employs the Reynolds Stress Model as turbulence model and the Volume of Fluid model as multiphase model, is followed. Results are validated qualitatively against experimental measurements from the previous studies. Keywords: CFD modelling, hydrocyclone, Reynolds stress model, multiphase flow

Jan 1, 2008

By John D. Bardill

Data from extensive tests was obtained on friction-head losses of various sand slurries, composed of materials of different specific gravities and under varying transport conditions, to provide useful information for designing hydraulic transport systems. The tests were run in a pilot plant through 2-, 3-, and 4-inch lines with slurries composed of relatively pure barite and limestone solids. Available grinding and classification equipment did not permit attaining a comparable size distribution in the two materials tested, thus preventing direct correlation of friction-head loss values to physical properties or mineral composition. A total of 495 measurements were made of limestone slurries in the 2-, 3-, and 4-inch pipe test sections at flow velocities from 6 to 14 feet per second and pulp densities from 40 to 70 percent solids. A total of 640 measurements of barite slurries were made in the 3-and 4-inch pipe test sections at flow velocities between 7 and 14 f.p.s. and pulp densities ranging from 40 to 80 percent solids.

Jan 1, 1962

Same-batch and non-blind as well as blind pulp duplicates are often submitted as quality assurance/quality control (QA/QC) control samples to a routine laboratory along with routine assays (and other control samples such as reference material samples). The current ways of interpreting the results of duplicate assays to derive QA/QC conclusions and decisions, however, has not yet been formalised in a scientific manner. The current, prevailing approach and its limitations are reviewed and a new method is proposed as a substitute tool. This new tool should allow for operational error detection on a batch per batch basis (ie batch rejection) as well as laboratory performance assessment with time on reproducibility.

Jan 1, 2008

By Slawomir Bock

One of the fundamental issues having a great influence on the safety of operations performed in underground mines is the support of workings which should assure their stability in a given geological setting and mining-technical conditions during the life of their use. The process of designing and planning support for roadways may use analytical and empirical, as well as numerical methods. In view of the rapid increase in the data processing capacity of computers and the development of more and more enhanced software for numerical modeling, it seems to be advantageous to use numerical methods in searching for design solutions ? especially in the case of non-typical mining and geological conditions and in cases that need to take into consideration a great number of factors. The assessment of rock mass quality is of basic significance in designing mine supports. Fractures, dividing the rock mass into blocks, have an essential influence on the stability of the rock mass and underground construction. This paper presents examples of the fundamental underground investigations on the rock mass conducted by the Department of Extraction Technologies and Mining Supports of the Central Mining Institute in Poland, such as: penetrometric tests, introscopic examination, laboratory testing of rock samples and ground penetrating radar. Moreover, this contribution also presents examples of applications of three-dimensional numerical modeling for the purposes of stress-strain analysis of the rock mass around mine workings and computer-aided support design by means of FLAC3D (developed by Itasca) and Cosmos/M (developed by Structural Research and Analysis Corporation).

Jan 1, 2009

By G. Song

"SynopsisAccording to the overlying rock strength and thickness of 10 shallow coal seams in China, the strata are classified into four types: weak and laminated strata (hereinafter referred to as WL), weak and massive strata (WM), strong and laminated strata (SL), and strong and massive strata (SM). The four types of strata, together with longwall panel height (M), panel length (L), and seam depth (H) are factors that influence the loads on hydraulic power supports. Principal component analysis was used to study the seven influencing factors. It turns out that seam depth (H) is multicollinear with WL, WM, SL, and SM. Thus the enumerated seven factors are divided into two models. In Model 1, six factors; panel height, panel length, and layer thickness of the four type strata are involved. In Model 2, three factors; panel height, panel length, and seam depth are included. Using multivariate regression analysis, two equations to calculate loads on supports are obtained for each model. The equations were applied to shallow coal seams. The equation of Model 1 is more accurate than that of Model 2, but Model 2 could be further used in deep coal seams. The equations were coded through VB programming to simplify the calculation.IntroductionTo ensure coal production in the long term, the focus of coal mining has been gradually shifted to the western areas of China in recent years due to rich coal resources in this region. Most of the coal seams in this area are shallow but the support loads are abnormally high. In these circumstances, the chock loads estimating methods used in the past do not work. If the rated working resistance of a support is larger than needed, the shield is unable to fully perform, while a lower working resistance would lead to accidents like shield crushing or even casualties. This problem is frequently found in shallow coal seams such as Shenfu-Dongsheng, Yulin, Tuha, Lingwu etc. (Zhang, 2011). Thus, to ensure safety and efficiency during mining, the estimation of support loads and selection of supports are of great significance."

Jan 1, 2015

By Jon R. Maki

"EVTAC, an iron ore mine in Minnesota, had trouble meeting the customer’s pellet silica requirements. In addition, the mine plan was moving towards a lower grade ore and funding was not available for plant improvements to compensate for the change in ore or improving quality. Small changes to optimize various processing equipment resulted in significant improvements in both quality and productivity; for example, productivity on one mill line increased by 10% while producing lower silica concentrate. This paper will provide the methodology that allowed EVTAC to improve quality and productivity through process optimization with little capital investment.INTRODUCTION EVTAC, an iron ore mine in Minnesota, had trouble meeting the customer pellet silica requirements. In addition, the short-term mine plan was changing to a lower ore grade. Because of limited funds, EVTAC did not have the capital for investing in the plant to compensate for the ore change or to make improvements to lower product silica levels. Small changes to optimize process equipment resulted in significant improvements in quality and productivity; for example, one mill line feed rates increased by 10% while also producing a higher quality concentrate. These changes were sufficient enough to allow the mine to lower the target ore grade beyond their initial goal. At one time, a $3M flotation facility was considered as a way to meet quality with the new ore grade. However, the process changes were able to accomplish the same silica reduction with roughly a $50,000 investment in VFDs for sump controls. This paper will discuss some of the modifications that allowed EVTAC to meet the quality and production objectives with little capital investment. It also discusses the methodology used to make these process improvements."

Jan 1, 2014

By Robert H. Robinson, Levent Ozdemir, Russell J. Miller

The paper summarizes an investigation into the applicability of mechanical excavation to oil shale mining; identifies available machine types that are best suited to various aspects of the mining operation; presents preliminary comments on the configuration of an "IDEAL" oil shale mining machine; and establishes the background information necessary for conceptualizing and evaluating new mining methods using mechanical excavation equipment. Conclusions are also presented as to the best currently available systems, as well as potential future systems.

Jan 1, 1983

By Rob Jameson

"The demand for commercial and residential construction has continued to evolve across the United States over the last decade. Our markets demand larger, deeper and inherently more complex structures, located within increasingly constrained urban locations and with challenging geotechnical conditions. As project demands incrementally escalate, specialty contractors are continuously challenged to extend their state of practice. Development in the size and capabilities of construction equipment, tooling, techniques, monitoring and verification systems over the last decade has consistently allowed contractors to build larger and deeper. For support of excavation (SOE), in addition to scale, selection of the most appropriate system has been a key to success in the most challenging ground conditions. This selection process is based on sound engineering and construction practice, and also prior experience, both positive and negative. Ultimately many Owners have chosen to manage their risk of SOE construction through design-build contracts, which allows specialty constructors to optimize the balance of cost, schedule, scope and associated risk based on their local expertise. Successful implementation of a design-build methodology begins long before a contractor is selected, with identification of key project requirements and risk factors during the feasibility studies and design development phases. In these early stages of the project development, advice and budgets are frequently solicited from Specialty Contractors. The Owner, Construction Manager and Consulting Team will filter this input from multiple sources to provide their specific recommendations, develop construction documents and select the appropriate form of contracting. Only in the final stages, after award of a Design-Build Subcontract, can the successful specialty contractor directly influence risk management approach on the project. A case study is presented from Block 9 in San Francisco’s Transbay District. This project demonstrates the incremental identification, assignment and mitigation of construction risk through the planning and design build process for SOE on the deepest planned excavation in San Francisco.INTRODUCTIONThe mature urban development market in United States results in high demand for complex Support of Excavation (SOE) schemes on constrained sites. The Design-Build approach can be applied to increasingly difficult SOE challenges, combining regional specialty subcontractor knowledge and experience in order to optimize solutions for cost and schedule. The most successful applications will involve early engagement of shoring subcontractors within the project teams, during feasibility and design development stages, in order to identify key scope and risk issues, and their potential solutions. Throughout the project development, it is important to reasonably assign responsibility for construction risks amongst the project stakeholders who are best able to control them.This paper presents a case history for San Francisco’s Block 9, a well-planned and successfully executed design-build SOE project in San Francisco’s Transbay Redevelopment area. Throughout the 4 year period from the Developers initial proposal to the Redevelopment agency, through completion of excavation down to subgrade, the project team developed a series of increasingly refined SOE schemes, with corresponding scope definition and cost and schedule estimates. This program relied on early identification of key challenges and risks for the project, and evolved through multiple phases of proposals as first the General Contractor (GC) and then Specialty Shoring Subcontractor were engaged for the project. The scheme, cost and schedule refinements continued throughout construction in order to accommodate unanticipated conditions and events as they unfolded."

Jan 1, 2017