Search Documents

By R. C. E. Bray, Peter Price

"The property of Pamour Porcupine Mines, Limited, is in the eastern Porcupine area, about 12 miles northeast of Timmins. It covers parts of lots 3-6 (inclusive), cons. 5 and 6, Whitney tp., Cochrane district, Ontario. It is an amalgamation of the old La Palme, Three Nations, and Porcupine Grande properties.The first discovery on the Pamour was made in 1911. During 1911 to 1914 a small shaft was sunk on the Three Nations vein to the 200-foot level and a 100-ton stamp mill was put in operation, but only a small production was achieved. The property remained idle from 1914 to 1923. In 1924 some diamond drilling was done along the Keewatin-Timiskaming contact with some encouraging results, but the gold mineralization encountered was too low in general at the price of gold then prevailing to warrant further · work. The increase in the price of gold revived interest in the area, and the above noted amalgamation was effected in 1934. Options were taken and successively dropped by two large mining companies. Following this, exploration both on the surface and underground was started by Quebec Gold Mining Corporation, Limited. Diamond drilling in the early part of 1933 showed considerable ore in conglomerate and greywacke to the east. In the middle of 1935 Noranda Mines, Limited, assumed control and management. A new shaft was sunk and the property was ·equipped with a mill having an initial capacity of750 tons a day. This was subsequently enlarged to 1,500 tons a day.From the commencement of milling (May 16, 1936) to the end of 1946, 5,025,545 tons of ore having an average grade of 0.1327 oz. a ton ($4.64 at $35 an oz.) have been mined and milled."

Jan 1, 1954

By William C. Peters

The frustration encountered by exploration crews in connection with land acquisition could be graphed to show a correlation with the natural law that everything tends to become more so. Figure I shows a rather common, situation. The combinations of ingredients are almost limitless and the resulting brew is often poisonous to an exploration man. A single step, that of taking a series of deep soil samples is often delayed until some sense can be made from "floating" unpatented claims which are obscure in orientation as well as position, placer claims overlapping lode claims, location posts with empty Prince Albert cans, and claims with no apparent assessment work for ten years. Add to this some patented claims with¬out monuments, a state or federal withdrawal area which may or may not invalidate pre-existing claims, a loosely defined tunnel site, and some ranchers who understandably resent the separation of surface rights from mineral rights. The picture is familiar to exploration men. One approach to such problems is to ignore them until someone voices an objection -- but then an even more chaotic situation is likely to develop. Another practice is to stake new claims to cover all ground that is "open" at first glance and then find out if there are conflicts so that the new claims can be adjusted accordingly.

Jan 1, 1970

By Jae-Chun Lee, Rajiv Ranjan Srivastava, Min-seuk Kim, Byung-Su Kim

Recycling of spent hydrotreating catalysts (HTC) can potentially contribute towards the sustainable extraction of metal values. Treating such materials by hydrometallurgical methods to separate metals from the leach liquor of either acid/alkali media is a major step. In the present study, separation of molybdenum from HCl leach liquor of spent NiMo type HTC has been investigated by applying solvent extraction using Cyanex-923. For this, the chloride solution containing 973 mg/L Mo, 254 mg/L Ni and 1634 mg/L Al was taken as the aqueous feed. The parameters including contact time, concentration of the extractant, acid and chloride, and phase ratio were varied to investigate their effect on the extraction efficiency. The McCabe-Thiele plot suggests that > 99% Mo-loading using a 2-stage extraction process. From the molybdenum depleted solution, nickel was selectively extracted by Cyanex-301 leaving Al in the raffinate.

Jan 1, 2014

By W. M. Corse

I bring this investigation to your attention to emphasize the needless waste attendent upon the use of tin plate with an unnecessarily heavy tin coating. With our present knowledge, we are unable commercially to produce coatings as light as the lower weights used in this test. If, however, future research should develop means to this end, the resultant product would meet all practical requirements, and a very considerable saving in pig tin would result. DISCUSSION G. H. Clamer.-—The National Canners' Association is studying the action of fruit juices, etc., on solders. Of course these tests will take quite a long time, and we hope by that time the war will be over and there will be no need for conserving tin for war purposes. Germany for a great many years has prohibited the use of more than 37 per cent. of lead in alloys used in contact with food products. The eutectic composition is 37 per cent. of lead and 63 per cent. of tin; alloys containing more than that percentage of lead have some free lead. J. W. Richards,' South Bethlehem, Pa.—A great deal of conservation can result from the packing of dry foods in cartons and in fiber packages instead of using sheet tin. Many of the boxes used for packing things other than food are frequently made of sheet tin because it prints and lithographs well; these could be made of sheet iron coated with copper or some other substitute metal which prints equally well. The Aluminum Bronze Industry W. M. CORSE,† Mansfield, Ohio.—The conservation of tin, in view of the shipping situation, is one of great importance. Several methods of conservation can be employed: 1. Reduction of the amount of tin in an alloy or compound. 2. Substitution of an entirely different metal or compound for tin. 3. A combination of the first and second methods. The second method is the one that I wish to discuss. Metallic aluminum, has been known for a long time, and its use in copper alloys was discovered about 1855 by Lord Percy. The high cost of production of metallic aluminum retarded its commercial development, and it was not until the discovery of the electrochemical processes for its production that it came to be known as a common metal. I have been particularly interested, for the past few years, in working with the alloy known as aluminum bronze, which is usually composed of approximately 90 parts of copper and 10 parts of aluminum, by weight.

Jan 1, 1919

By W. D. Hausel

The Wyoming Province is an Archean craton which underlies portions of Idaho, Montana, Nevada, Utah, and much of Wyoming. The cratonic block consists of Archean age granite-gneiss with interspersed greenstone belts and related supracrustal terranes exposed in the cores of several Laramide uplifts. Resources found in the Province and in the adjacent accreted Proterozoic terrane include banded iron formation, Au, Pt, Pd, W, Sn, Cr, Ni, Zn, Cu, and diamonds. The Province shows many similarities to the mineral-rich cratons of the Canadian shield, the Rhodesian and Transvaal cratons of southern Africa, and the Pilbara and Yilgarn blocks of Western Australia, where much of the world's precious and strategic metal and gemstone resources are located.

Jan 1, 1991

By C. J. Newman

Production levels at the Kidd Creek copper operation increased during the 1980's by expansion of both the smelter and refinery and by major modifications to equipment which was causing bottlenecks. As a result, there was a significant reduction in the unit cost, some manpower reductions and hence a significant increase in productivity. In the last two or three years, there have been no major expansion projects leading to unit cost reductions and yet these have still been attained. This has been achieved by the development and implementation of various techniques designed to maximize the inherent potential of the operators and maintenance employees. This paper will initially describe the operation but will then place emphasis on employee involvement through such methods as idea awards, incentive schemes, loss control and continuous improvement programs. Organizational changes are discussed, particularly with reference to changes from the traditional operator role to one which encompasses maintenance skills and to cross-training of maintenance employees into multi-discipline fields. The effect of these changes are discussed by a review of the salient plant parameters of safety, production levels, cost and quality.

Jan 1, 1993

By J. O. Marsden, M. M. Botz

"Heap leaching is responsible for approximately 21 percent — 3.9 million metric tonnes — of copper production and 9 percent — 270 metric tonnes or 8.7 million ounces — of gold production worldwide. Given metal price assumptions of $2.25/lb for copper and $1,250/oz for gold, these portions of global production generate revenues of $19 billion and $11 billion, respectively. For heap leaching operations, small changes in metal extraction efficiency drive substantial changes in operating cash flow margins and affect project viability. Variances in actual metal production from budgetary forecast estimates can mean the difference between success (value creation) and failure (value destruction) for a heap leach project. Despite the importance of heap leaching for copper, gold and silver production worldwide, there are no clear standards or guidelines for developing heap leach metal production forecasts. There is considerable variation among copper and gold producers that apply heap leaching technology as to how such modeling and forecasting is applied at the operational level. There are a variety of different modeling approaches that can be utilized for this purpose. However, these vary in cost, complexity, time to implement, accuracy and credibility. This paper explores the options available for heap leach modeling, discusses the advantages and disadvantages of each approach, and provides guidelines/recommendations for an effective approach to modeling metal production at existing or planned heap leach operations. The paper also provides expected ranges of variation between actual and modeled production.Introduction and backgroundHeap leaching is fundamentally different from other methods used in the processing and extraction of gold, silver, and copper and other base metals. Considered globally, the technique represents a relatively modest portion of production compared with the primary technologies applied for copper and gold recovery. Approximately 21 percent of copper production is attributable to heap leaching techniques, as opposed to 79 percent by conventional crushing, milling, flotation, smelting and refining. For gold, about 9 percent of global production is obtained from heap leaching, compared with over 90 percent by various combinations of crushing, milling, gravity concentration, flotation and/or agitated cyanide leaching processes or, in the case of placer deposits, by direct gravity concentration and/or amalgamation. In cases where heap leaching is the primary source of metal production, the ability to accurately forecast metal production may be the difference between commercial success and failure for a project or operation. Heap leaching — of crushed or run-of-mine ore — is also commonly applied as a secondary process to treat lower-grade ores from a given deposit, such as at Chuquicamata in Chile, Cerro Verde in Peru and Bagdad in Arizona for copper extraction and at Twin Creeks and Carlin, both in Nevada, for gold. In such cases, heap leaching provides incremental revenue to supplement the primary process. Variances between actual and forecast metal production from heap leaching as a secondary process are typically tolerated and absorbed within the overall site metallurgical balance. In either case, accurate production modeling and forecasting creates significant value for heap leaching projects, is essential for managing production expectations — timing and volumes — and is likely to be a critical success factor for most heap leach projects."

Jan 1, 2017

RISKGATE is an interactive online risk management system developed by the Minerals Industry Safety and Health Centre (MISHC; University of Queensland) to maximise health and safety performance in the mining industry through implementing continual improvement in management of major unwanted events. A comprehensive knowledge base has been captured for risk management of tyres, collisions, fires, isolation, strata underground, ground control open cut, explosions, explosives, manual tasks and slips/trips/falls. This will be extended to outburst, coal burst and bumps, interface displays and controls, tailings dams and inrush in 2013. RISKGATE presents substantive and leading edge controls to assist industry stakeholders in the design, management and reporting of organisational and regulatory compliance requirements. From a broader industry perspective, RISKGATE provides an environment for knowledge capture and knowledge exchange to drive innovation and best practice in the identification, assessment and management of risk. By capturing operational knowledge from industry experts, RISKGATE provides a cumulative corporate memory at a time of high personnel turnover in the coal industry. All major Australian mining companies are contributing topic experts to this broad industry initiative. In the first 24 months, nine coal mining companies nominated over 80 different experts who contributed over 400 days of individual time to the knowledge capture workshops. RISKGATE is the largest single Australian Coal Association Research Program (ACARP) occupational health and safety (OHS) initiative to date.

Aug 1, 2013

By W. D. Macleod

This paper describes a mineral dressing process for the upgrading of tin ores. The process described is called 'agglomeration' and. is similar in many respects to flotation. Many variables have been examined experimentally both on batch and continuous operations and are reported upon herein... Using a Mt. Pleasant tin ore, assaying 0.5% Sn, an upgrading to 8% Sn, with a recovery of 95% could be obtained by this process.

Jan 1, 1966

By Donna Guillen, Matthew Lehar, Sebastian Freund, Jennifer Jackson, Helge Klockow

"Research and development is currently underway to design an Organic Rankine Cycle (ORC) system with the evaporator placed directly in the hot exhaust stream produced by a gas turbine (GT). ORCs can be used to generate electricity from heat that would otherwise be wasted, thus producing carbon-free energy. In conventional ORC configurations, an intermediate oil loop is used to separate the hot gas from the flammable working fluid. The goal of this research effort is to improve cycle efficiency and cost by eliminating the pumps, heat exchangers and all other added cost and complexity of the additional heat transfer loop by developing an evaporator that resides in the waste heat stream. Direct evaporation – although simpler and less expensive to implement than indirect evaporation of the working fluid – has historically been avoided due to a number of technical challenges imposed by the limitations of the working fluid. The high temperature of the hot exhaust gas may cause decomposition of the organic working fluid and safety is a major concern due to the high flammability of some of these working fluids. The research team has addressed these challenges and developed a new direct evaporator design that can reduce the ORC system cost by up to 15%, enabling the rapid adoption of ORCs for waste heat recovery. The ORC system is intended to integrate with the GT either as a retrofit or to be marketed as a single package, thus maintaining the manufacturer’s warranty.IntroductionWaste heat from turbines and engines used in industrial applications along with waste heat from industrial processes are exceptionally abundant sources of energy. If even a fraction of this waste heat could be economically converted to useful electricity, it would have a tangible and very positive impact on the economic health, energy consumption, and carbon emissions in the U.S. manufacturing sector. Land-based gas turbines are used in a broad range of applications to produce both shaft and electrical power. Most commonly known for generating electricity either as peaking units or as base load units, they are also used to directly drive pumps, compressors or other machinery requiring shaft power. Simple cycle gas turbines have the advantage of a short startup time relative to coal-fired and nuclear units, however, they incur a significant penalty on their efficiency. Large frame gas turbines usually are combined with bottoming steam-based Rankine cycles to increase the overall efficiency of the system and thereby improve their cost performance. Small-frame gas turbines with exhaust temperatures around 500°C could in principle benefit from steam bottoming cycles, but rarely use them in practice because of the high capital cost of the steam system. Particularly for base load small frame gas turbines, akin to those used in pipeline applications, an increase in efficiency is highly desirable."

Jan 1, 2011

By Wesley A. Grosh

The Valzinco mine, Spotsylvania County, Va., is a lead-zinc deposit with minor quantities of copper. The property was reopened n 1942 by Panaminas, Inc. The Bureau of. Mines, in an effort to increase the reserves of the deposit to justify greater production, diamond-drilled nine holes totaling 4,213 feet during 1943. Drilling by the Bureau delimited the original ore body and discovered another ore body on the hanging-wall side, which was being developed by the company at the close of the project.

Jan 1, 1949

By R. S. Dean

The possibility of cheap electric power for a number of mining areas in this country has suggested to many the idea of electric smelting of nonferrous ores in small units at or near the mines. The electric smelting of nonferrous ores was tested fairly thoroughly 20 years ago by United States Bureau of Mines and by others, and the fact that it did not achieve continuing workable success in any instance is sufficient proof that it offered no advantages at that time.

Jan 1, 1937

By Joseph E. Pogue

FOR a number of years the petroleum department of The Chase National Bank has been making a continuing study of the financial aspects of thirty oil companies. (See Pogue and Coqueron, "Financial Analysis of Thirty Oil Companies," pamphlet, The Chase National Bank, November 1945, for data covering eleven years, 1934-1944, and the list of the companies making up the group. See also "Capital Employed in the Petroleum Industry," by the same authors, M&M, November 1944.1 This group represents a large sample of theAmerican petroleum industry, covering about two thirds of the business. Certain aspects of this study concern the capital employed in crude oil production, the main features of which arc presented in this paper.

Jan 1, 1946

By Ker-Chang Hsieh

Four three-phase equilibria and one two-phase equilibrium in the FeNi- S-0 quaternary system in the vicinity of 1023 K and Pso2 = 1 atm were studied using the following emf cell 2 Pt,o2 (air)Zr02 .CaO/Pso2 = 1 atm, mixture of phases, Au The four three-phase equilibria are sp + (Fe,Ni )S + Ni 3s2, sp + Ni 3s2 + NiO, sp + NiO + N1S04 and Fe2 o3 + sp + (Fe,NOS04 -Y:he two-phase equilibrium is sp + (Fe,Ni)S. The two-.phase equilibrium was measured by using mixtures containing a major portion of one phase and a minor portion of the other. The results are presented in terms of oxygen potential as a function of YNi = nNi/(nN1+nFe) at constant temperature and pso2 = 1 atm. The stability diagram was also calculated using appropriate thermodynamic models for all the pertinent phases. The calculated diagram is in accord with the measured ones.

Jan 1, 1985

By D. I. Hoyer

A preliminary model has been developed for autogenous pebble milling using information obtained from studies on ball milling and SAG milling. The model treats the breakage as the weighted sum of first-order breakage of smaller particles by tumbling pebbles, non-first order breakage of larger particles which are too large to be nipped properly by pebbles, autogenouS fracture and chipping of larger lumps to form pebbles, and autogenous fracture and abrasion of pebbles. The model includes the effects of residence time distribution, classification through the exit grate, and a mass transfer relation which describes the accumulation of fine material in the mill. Example simulations are given, based on breakage parameters determined from batch grinding tests in laboratory mills. fracture breakage and abrasion. In the development of these preliminary mass balance equations it will be assumed that breakage by fracture is first-order, but this assumption will be modified later in the paper. It will also be assumed that the residence time distribution of a long autogenous mill can be described by an equivalent series of m fully-mixed mills, with a classification action imposed on the mill contents by the discharge grate. Size distributions are expressed as a v2 geometric series, numbered 1 for the top size down to n for the fines, or "sink" interval. If the holdup in the mill is W then the rate of breakage of material in size interval i is given by SiwiW, where wi is the fraction of material in size interval i, and Si is -the overall specific breakage rate of size i material (fraction per unit time).

Jan 1, 1985

By AIME AIME

M ODERN metallurgy properly belongs to this century. The great advance made in this science is directly attributable to the discovery of the Roentgen rays. Application of the results of this discovery, together with the more recent corroborating studies in electronic diffraction have definitely and for all time established this science. Metallurgists today speak with familiarity of the atoms of the different metals in terms of their orientation, atomic volumes, lattice structures, dimensional lattice constants distance of nearest approach, and the like. One matter of profound interest, which is quite staggering to the imagination of the human mind, is the enormity of the number of atoms even in a small particle of metal. As an illustration, let us compute the number of atoms in the volume of one cubic centimeter in a single grain of absolutely pure copper. Eighteen and a fraction cubic centimeters equal the volume of one cubic inch.

Jan 1, 1940

By A. L. Hauff

As US Coal producers are looking more and more to the international markets, they face the complex job of planning and managing transportation logistics which make effective use of production capabilities, considers the various contract requirements to be fulfilled, Train, Truck and Vessel capacities, port restraints, etc. Pulling all the necessary pieces of information together to allow proper planning throughout the supply chain is often a time consuming, manual but necessary task. This paper will discuss the various constraints, requirements and considerations to supplying coal to a global market.

Jan 1, 2012

By G. H. Martindill

Complex chemical and physical changes occurring during carbonization result in a heterogeneous system composed of gaseous, liquid, and solid phases, whose relative proportions and chemical compositions change constantly as temperature increases. Studies in which the participating variables are isolated and controlled should be useful in formulating the mechanism of coal carbonization. The most characteristic property of a coking coal is its ability to form a plastic mass at a certain stage of the carbonization process. During this period it is believed that fluidity of the coal influences the properties of the resultant coke. This report gives results of an investigation by the Federal Bureau of Mines of the influence of the maximum fluidity attained by the charge on the physical quality of the coke or char produced. As a first approach to the problem, researchers investigated high-melting-point pitches, which are relatively simple carbonaceous materials. The plastic properties of these pitches, prepared specially for this work, varied greatly; their fluidities, as measured by the Gieseler plastometer, covered most of the fluidity range characteristic of coking coals. Blending these pitches with increasing pro-portions of fine coke progressively reduced their fluidities. Coal-pitch and coal-coke blends also were treated; their fluidities were varied by changing their blending ratios. The various blends were carbonized in a small-scale carbonizer and the resistance of the carbonized residue (char) to abrasion was determined in a small-scale tumbler test, using the Roga drum.

Jan 1, 1960

By M. P. Hoffman

The U.S. Bureau of Mines is developing a roof bolter with a computer-controlled drill head that will increase the safety of roof bolting in underground coal mines by allowing miners to be relocated to a safe area. To ensure secure anchorage, acceleration and strain data are broadcast from an instrumented drill steel to a data acquisition system. These data are analyzed, correlated, and transformed to pro-vide information about roof strata, then are sent to a supervisory computer executing National Institute of Standards and Technology's real-time control software. The supervisory computer sends setpoint commands to proportional-integral-derivative control loops to control drill thrust, position, revolutions per minute, and torque.

Jan 1, 1994

By K. O. Bennington

[Thermodynamic properties of two amphibole asbestos minerals were determined by the Bureau of Mines. The enthalpies of formation were determined by the hydrofluoric acid solution calorimetry method. Heat capacity measurements were made with an adiabatic calorimeter over the range of 5 to 315 K. High-temperature enthalpies above 298 K were determined with a copper-block drop calorimeter to 852 K for amosite and to 902 K for crocidolite. Thermodynamic data determined for amosite of the composition Fe5+2.2766Mg1.5209 Fe+03.12Mn0.0825) Si7.9163Al0.0837022.0363)(OH)1.9637 are: S°298 = 168.8 ± 5 cal/deg-mole; ?Hf°298-15 (elements) = -2419.24 ± 2.95 kcal/mole; ?Hf298.15 (oxides) = -30.92 ± 2.47 kcal/mole; and ?Gf° -2260.1 kcal. Corresponding data found for s3 ,1s = crocidolite of the composition (Na1.9Ca0.1)(Fe2+.024Fe2.5 01Mg0.475) (Si7.9713024Fe+2 2.501Mg0.475) (Si7.971 Al0.029022.095) (OH)1.905 are: S2.98-15 - 161.1 ± 4 cal/deg-mole; ?Rf° 2 298.15 (elements) = -2433.56 ± 2.99 kcal/mole, 10298.1s (oxides) = -87.69 1.70 kcal/mole, and ?Gf°298.15 = -2269.8 kcal.] Calorimetric values from this investigation were combined with other data from the literature to calculate the Gibbs energies of formation and equilibrium constants of formation over the temperature range of the measurements. Tables of enthalpies of formation and Gibbs energies of formation are given as a function of temperature both from the elements and the constituent oxides.

Jan 1, 1978