Search Documents

By Mark Rybak

On Aug. 31, 2006, Tropical Storm Ernesto hit the city of Richmond, VA. The Battery Park area was hit particularly hard, as flooding forced an evacuation of the area. A large sinkhole collapsed a sewer line in the Battery Park area, blocking the pipe and causing more serious flooding. This article describes the fast track design, bidding and construction of an emergency tunnel to bypass the collapsed sewer. Innovative value engineering, tunneling and shaft-sinking methods and final lining design all contributed to the success of this project. The storm inundated Richmond, VA with up to 305 mm (12 in.) of rain that, in some areas, caused widespread flooding and damage. One of the hardest hit areas of Richmond was Battery Park. A major trunk sewer in the Battery Park area collapsed and caused local combined sewer and stormwater flooding. The collapsed sewer was a 2.4-m x 76-mm (8-ft- x 3-in.-) wide by 2.7-m- x 152-mm- (9-ft- x 6 in.-) high arch sewer that was constructed in the 1920s and later filled over with municipal solid waste and a soil fill cap to cur-rent elevations. A sinkhole was created in the area of collapse approximately 18 m (60 ft ) deep and 31 m (100 ft) in diameter. This caused the existing arch sewer to become blocked. As a result of this blockage, contaminated floodwaters reached depths in low-lying areas in excess of 8 m (25 ft).

Jan 1, 2008

By R. L. Bruening, N. E. Izatt, S. R. Izatt

"Rare earth elements (REE) are essential and unique components of many high-technology products without which functioning of modern society would be greatly impaired. Commercial deposits of REE are limited to a few geographical locations. Largely untapped sources of REE are available in endof- life (EOL) magnets, rechargeable batteries, and electronics. Presently, < 1% of REE in EOL wastes is recycled. Conversion of EOL wastes to liquid streams allows use of IBC’s Molecular Recognition Technology (MRT) process to selectively recover, separate, and purify target REE and associated metals at g/L to mg/L or lower concentration levels. The MRT process together with its applications to separations of REE and associated metals in recycling as well as in mining are described. Economic and environmental advantages of MRT are presented. INTRODUCTIONRare earth elements (REE) include the lanthanide series (La-Lu), Y, and Sc. These elements are not rare, but concentrated minable deposits are scarce (Cordier 2012; Haxel, Hedrick, & Orris, 2002). Over 95 % of the world’s supply of REE is controlled by China (Hanson, 2011a) where they are mined, processed, and the pure elements incorporated into a growing number of consumer and military products. The consumer products are marketed worldwide. Since REE are vitally important in consumer and military products, this situation has caused other nations to scramble to develop the capability to produce their own supply (Cordier, 2012).In the U. S., Molycorp has reopened the Mountain Pass REE mine in California and production has begun (Goldenberg, 2010). Development of a reliable internal source of REE is of high national priority in the U.S. (Hanson, 2011b; Hess, 2012: “Obama Announces”, 2012). These elements have in recent decades been incorporated into new consumer and military products that are essential to our economy and defense. These products range from wind turbines, high performance magnets, hybrid car rechargeable batteries, energy efficient lighting electronics, flat screen televisions, and smart phones to advanced weapons systems (Haxel et al., 2002; Levkowitz & Beauchamp-Mustafaga, 2010)."

Jan 1, 2012

By M. Cornelius

Drilled shaft construction through caving soils has historically been an uncertain, risky and costly operation. Uncertain, because the zone of caving may or may not be known, risky because the loss of a shaft is disastrous, and costly because the Contractor, who faces these risks, must include large sums of money in his bid for shaft wall stabilization techniques. This case study will discuss the stabilization techniques that are typically used within the United States, and then present new technologies, born in Europe, that are being utilized in the States by Malcolm Drilling Company today.

Jan 1, 1999

By J. E. Terry

This paper outlines the steps that are being taken to close the gap between training and industry and indicates areas in which more work needs to be done. Although based on experience in the Maritime Provinces, it is applicable to industrial and educational studies across the length and breadth of Canada.

Jan 1, 1970

By Igor Zh. Bunin

A model for developing electric discharges between sulfide mineral (pyrite) particles under high-voltage nanosecond pulses in a liquid medium (water) is considered. A possibility of electrical breakdowns of liquid gaps between particles under nanosecond pulses is shown. This probability and the energy released in discharge channels depend strongly on the sulfide conductivity.

Jan 1, 2010

Explosives identification tagging refers to the addition to explosives, during manufacture, of coded microparticles that can survive detonation, be recovered and decoded, and allow the explosives to be identified and traced to the last legal possessor as a result of distribution records kept of the coded tagged explosives. This study seeks to prepare the way for National implementation of identification tagging of all dynamites and cap-sensitive slurries (also known as water gels) by resolving technical issues and by developing a plan for pilot testing of the program. It is presented in two volumes: Volume I, National Implementation Model, and Volume II, Pilot Test Plan.

Jan 1, 1977

By Madsen I. C, Langberg D. E

Recent advances in X-ray diffraction (XRD) technology have made it possible to conduct powder XRD measurements on samples at high temperatures during reaction. State-of-the-art detectors are now capable of rapidly acquiring diffraction patterns across a wide angular range (typically 120"20) enabling phase transformation rates to be measured directly during sample reaction. In this study, the phase transformations during the reduction of hematite to metallic iron by five per cent hydro ºen in nitrogen gas mixtures, were measured in situ between 500 - 700 C. Complete X-ray diffraction patterns were acquired within 15 seconds every one minute, enabling direct measurement of the transient phase abundances during the reaction. The data were quantitatively analysed by the Rietveld method to yield the abundances of hematite, magnetite, wustite and metallic iron, as functions of time during the reduction process. A first-order reactions-in-series model was proposed, and the reaction rate constants and activation energy were determined from the time-dependent phase abundance data.

Jan 1, 1999

By R. W. Bruhn

The objective of the study is to examine the apparent influence of soil and near surface rock strata on the severity of damage experienced by surface structures subjected to mine subsidence. The report discusses: 1) modes of ground movement that might complicate or be confused with mine subsidence; 2) prevailing concepts concerning mine subsidence in the Northern Appalachian Coal Field and Illinois Basin; 3) apparent influences of soil and near surface rock strata on the character of subsidence-related ground movements; 4) classifications and criteria for characterizing damage due to ground movements; and 5) types of subsidence damage experienced by homes above active mines in western Pennsylvania. Presented is a damage classification system incorporating a severity index for characterizing subsidence damage to homes with basements above active mines. A series of case histories illustrate subsidence damage to structures above active and abandoned mines.

Jan 1, 1983

By D. Wolfe, R. Cleminson

"The Aurora North mine has been operating for more than ten years, and is the source of over half of Syncrude’s bitumen production. The hydrotransport systems at Aurora experience high rates of wear, and mission lengths on current slurry pumps are nominally 1,500-2,000 hours. Recent work has enabled a better understanding of the significant adverse effect of large particle impingement damage to impeller vane leading edges - which is the known life determining issue for Aurora hydrotransport pumps. A new pump design has been developed and installed at Aurora, incorporating significantly increased impeller diameter and pumping vane lengths. The new pumps are expected to triple Aurora’s previous mission length for hydrotransport pumps. Part II of this paper will share actual hydraulic and wear performance observed in the first several months of operation, and draw comparisons relative to what was expected for these pumps in design / development.INTRODUCTION Slurry Pumps are Critical Equipment at Syncrude Slurry pumps are a key component in Syncrude’s operations. In a typical Aurora application, each 5000 HP pump stage helps move over 8,000 dry tonnes per hour of oil sand, plus an equal volume of process water that has been added to create the slurry. The average impeller life in oil sand hydrotransport service at Aurora has been nominally 1,500 to 2,000 hours, or 12 to 16 million tonnes of oil sand pumped. Generally, the slurry pump application at Aurora has proven very difficult to improve due to the unique combination of high sand abrasivity, 125 mm (5”) large particle top size (lumps), and high flow rate relative to basic pump size; a factor that results in unduly high impeller vane leading edge speeds for the service conditions."

Jan 1, 2014

Concentrations of bright green material in the &quot;Golden Mile&quot; of Kalgoorlie, which carry particularly high gold values, are known locally as &quot;green leader&quot;.This assemblage consists largely of quartz, sericitic muscovite, carbonates, and pyrite. Some of the sericitic muscovite contains vanadium, giving the rock its green colour. Vanadium oxides, including nolanite, are also present. Tellurides identified in this study are calaverite, altaite, petzite, melonite, and coloradoite. Native gold was found in most of the samples; some of the gold, at least, has been formed from the decomposition of gold tellurides.It is suggested that mineralizing solutions carrying gold and tellurium leached vanadium from the host rocks and subsequently deposited gold tellurides and vanadium-bearing minerals in the &quot;green leader&quot;.

Jan 1, 1977

"The mining industry uses many types of mineral and metallurgical plants to produce saleable product from ore mined. Plant design history has left current operations with a mixture of manual operation and various forms of automated process controls. Consequently, we typically see high variability in the continuous operations together with a shortfall in the attainment of full capacity, or higher utilisation of consumables.At a level of best practice, ‘Operational Performance Excellence’ focuses on process control, using automation and control systems to deliver process optimisation. This more sophisticated delivery is a great deal more difficult than the first stage of equipment selection / installation. It includes the appropriate selection of the right instrumentation, control system, key process knowledge, individuals with a solid control engineering background / experience, and the essential backing / support of the operations management team together leading to higher value delivery. Robust solutions can be realised, considerably minimising process variation, thus leading to process optimisation. This approach results in an easier, efficient and safer process while providing considerable returns for the plant owners.How variable are your processes, and do you maintain optimised process performance with dedicated resources, modern instrumentation, ‘best practice’ control systems and performance monitoring tools? In this paper, these questions and their possible answers are discussed."

Jan 1, 2014

By A. D. Pienaar

The aqueous chemistry of niobium and tantalum compounds with hydrofluoric acid is a mature field of investigation. In contrast, very little attention has been paid to reactions of these compounds in non-aqueous environments. Similarly, reactions of elemental fluorine with niobium and tantalum compounds have received little more than cursory attention in literature. This work discusses the isothermal reaction kinetics derived from thermogravimetry, using a less redundant approach than is currently the standard. We also discuss the most likely kinetic models for this reaction.

Jan 1, 2012

By Vince Luongo

PROJECT DESCRIPTION The York Durham Sanitary System (YDSS) Interceptor in the Town of Richmond Hill located just north of Toronto, Ontario, Canada will see the construction of a tunnel extending along 19th Avenue for a length of approximately 3.8 Km from Yonge Street, east to Leslie Street and will have a minimum internal diameter of 2.1 m. t to Leslie Street and will have a minimum internal diameter of 2.1 m. The tunnel will connect into four shafts, for which two of the shafts will be constructed using the slurry wall construction method given the high water table and difficult ground conditions encountered at these locations. The two shafts noted as Access Shaft No. 2 and No. 3 were designed and constructed to meet regulatory conditions, which required a sealed shaft construction method. GEOGRAPHICAL PROFILE The ground conditions in the Toronto region consist predominately of glacial till, glaciolacustrine and glaciofluvial sand, silt and clay deposits, and beach sands and gravels. The shallow geological formation found in the project area consists of four types of deposits: Oak Ridge Morain deposits, Halton Till, Glacial lake deposits and Organic soils. The Oak Ridge Morain is the dominant deposit encountered along the tunnel alignment. This formation consists of three deposits: The Upper Till, Middle Sand and the Lower Till. Standard penetration tests (SPT) carried out in these deposits measured N-values ranging from 2 to more than 100 blows/300mm which indicate very loose to very dense soil conditions. The Middle Sand deposit will be the dominant feature within the slurry wall construction at access shafts 2 and 3. Access Shaft 3 The base of the slurry wall will be 20.5 M below the ground surface. Slurry wall excavation will be within peat and organic soils found at the upper 3 M, followed by 5 M of the Upper Till. The remainder of the excavation will be within the Middle Sand. The piezometric head elevation is found at the ground surface. Access Shaft 2 The base of the slurry wall will be 22.5 M below the ground surface. Slurry wall excavation will be entirely within the Middle Sand 2.The piezometric head elevation is found at 7 M below the ground surface.

Jan 1, 2007

By Collin L. Stewart

The high cost and limited flexibility of modern longwall systems has resulted in the need for mine engineers and geologists to predict possible adverse mining areas ahead of mining and to then design and implement suitable ground control solutions in a timely and cost effective manner. Therefore, over the last 30 years, geo-technical evaluations for coal mine planning and development have advanced from a minor afterthought to an important part of today?s successful, high capacity, longwall mining operations. The latest iteration in this progression of improved analysis for predicting future mining conditions is a computer-based Stability Mapping System developed by West Virginia University. This system is designed to allow the mining engineer and geologist to effectively combine the mine geologic characteristics, stress influences, and structural features into an integrated stability map for use in mine planning and support design. This paper details the application of the stability mapping system to Bowie Resources, LLC, Bowie No. 3, multiple-seam longwall coal mine. At this mine, the prediction of adverse mining conditions using the stability mapping system allowed management to accurately adjust their support densities and operational procedures, and to successfully mine through difficult conditions safely and successfully.

Jan 1, 2006

By B. Hilscher, P. Nayak, N. Yoon

"The mining industry is currently facing challenges with declining feed grades and is struggling to find solutions to improve the project’s economic value. By means of pre-concentration, ore sorting aims to separate the barren material from the valuable ore to reduce energy consumption and tailings generation, while increasing the feed grade, concentrate grade, mill recovery, and revenue. In addition, ore sorting allows the modification of deposit geometallurgy in order to allow the creation of an optimal mill feed.This paper evaluates the applicability and challenges of ore sorting by utilizing the results from four different mines, and reviews them in detail. The mines include two underground and two open pit mines that are base metal and precioius metal operations. In order to understand the applicability of ore sorting in these operations, initial rock-by-rock test results and different types of assays (atomic adsorption [AA], inductively coupled plasma [ICP], and fire assay) are utilized. Using the assay results, the grade recovery curves for ore sorting are generated and they are further improved by using and developing an ore sorting algorithm, which is discussed in this paper. The application and evaluation of ore sorting in greenfield and brownfield properties will also be discussed.The state of the art ore sorting technologies for both rock-by-rock and bulk sorting are reviewed in this paper. The future technologies on the horizon, including different combinations of sensors, are explained. The sorting technologies include, X-ray transmission (XRT), X-ray fluorescence (XRF), colour, infrared, electromagnetic, and laser induced breakdown spectroscopy (LIBS).IntroductionOre sorting is a sensor-based sorting technique introduced between the excavation stage and processing stage, where the unwanted waste is diverted to the waste dump and only the ore is sent to the mill for further processing. As a result, the quality of the material entering the mill is improved and the dilution of the ore is reduced. In greenfield projects, sensor-based ore sorting provides an opportunity to reduce the capital cost of the project and increase the return on investment (ROI). With most operations currently facing the challenge of finding a high grade deposit, having a sorting unit provides several advantages while keeping the cost at minimum."

Jan 1, 2017

By Elmer Stewart, Richard May

"The Central Mukur deposit was discovered by the Semipalatinsk Geological Exploration Expedition (GEE) during detailed searches from 1977 to 1980. Andas Altyn Ltd., a Kazakhstanian gold mining company acquired the property and commenced mining in 1995. In 1998, Andas-Altyn Ltd. became a wholly owned subsidiary of Eurasia Gold Corporation.The Central Mukur gold project covers a linear series of parallel, discontinuous zones of near surface oxide gold mineralization that covers a distance of 7 kilometers and extends past the property boundaries. The oxide gold mineralization is a result of the regional oxidization of a primary sulfide gold mineralization emplaced in a series of shallow dipping thrust faults. Resources as calculated by the GEE are 3.45 mt at an average grade of 1.84 gmt Au in the C1 +C2 category and 7.52 mt at an average grade of 1.80 gmt Au in the P1 category. The Central Mukur Gold Heap Leach Mine consists of an open pit, heap leach pads, and an ion exchange resin gold recovery plant. Limited gold production (<2,500 ounces/year) has been achieved over the past three years leaching run of mine oxide gold mineralization. Gold recovery utiling cyanide to dissolve the Au and ionic resin technology to recover the Au for the leachate is approximately 60%. Loaded resin is shipped to a treatment plant at Almaty where the gold is stripped from the resin, refined and sold.This paper will describe the geology, mining, and processing of the Central Mukur ore. In addition, it will describe what it is like doing business in Kazakhstan and the transition from a Soviet style operation to a more western style operation.INTRODUCTIONThe Central Mukur Mine is owned and operated by Andas-Altyn Ltd. a Kazakhstanian gold mining company located in northeast Kazakhstan. Andas-Altyn is a wholly owned subsidiary of Eurasia Gold Corp., a Canadian public company listed on the Alberta Stock Exchange. The Central Mukur mine consists of a small open pit, and a heap leach operation that utilizes ion exchange resin to recover gold from pregnant solutions. In addition to the Central Mukur mine, Eurasia also owns the Myaly heap leach gold project which is also operated by Andas- Altyn Ltd."

Jan 1, 1999

By Kenneth B. Higbie

METALLURGICAL ACTIVITY in 1963 was again dominated by the insatiate demands of research and development conducted in conjunction with the nation&apos;s defense and aerospace programs. An increasing effort was noticeable throughout the year, however, to apply to the commercial field many of the processes and techniques that have been developed by government-sponsored research. Particularly effective has been the Industrial Applications Program of the National Aeronautic and Space Agency through which many of the technological advancements made during the course of NASA research and development have been published and released to the public. POWDER TECHNOLOGY Powder metallurgy techniques for fabricating metals, not long ago declared outmoded because of improved casting and shaping methods, have since made an astonishing comeback. Traditionally mechanical pressing of powder shapes has been employed when melting and casting was difficult or impossible, when phase relationships needed to be sidestepped, or when machining costs could be avoided. Hence, it has long been used for producing relatively small special shapes of high-melting metals and alloys. Small iron parts produced with a punch and die have been common for many years, but powder metallurgy techniques are now applicable to a wide range of materials and items. Hard-to-handle materials including refractory metals and their alloys are now rolled, forged, or extruded from billets made by sintering isostatically compacted powders. The major element of the powder metallurgy industry still comprises iron shapes, however, and two-thirds of the annual 100,000 tons of powder metallurgy products are made of iron. The largest single user of powder-forming techniques is the automobile industry which currently consumes 14,000 to 16,000 tons of iron powder per year. A typical 1963 model auto contained more than 100 pressed powder parts (e.g., transmission gears, timing gears, sprockets, ball joint suspensions) totaling 5 to 7 pounds per car. Some of these powders are used in self-lubricating parts of porous copper and copper alloys containing as much as 20 volume-percent lubricating oil. The expanded use of powder techniques, coupled with

Jan 1, 1964

By Alan D. Fisher

Amtrak made a decision to replace an aging bascule bridge with a vertical lift bridge for their crossing of the Thames River in New London, Connecticut. The new lift bridge occupies the same alignment and shares the same foundations as the bascule span. During construction the deep foundation caisson supporting the bascule span settled and tilted. Investigation into possible reasons revealed interesting historical facts, both of the construction of the innovative open well caisson foundations and of the state-of-the-art in tremie concrete placing methods in use at the turn of the century. This paper describes both of these topics.

Jan 1, 2008

By Brian H. Greene

The U.S. Army Corps of Engineers, Pittsburgh District, is in the final phases of modernizing the locks and dams on the Monongahela River. One facet of this modernization is to replace the existing Locks 4 located on the Monongahela River approximately 40 river miles upstream from Pittsburgh, Pennsylvania. The existing locks consist of a 56-foot x 720-foot main chamber and a riverside 56-foot x 360-foot auxiliary chamber built in the 1930s. Two new lock chambers, each 84-foot wide by 720-foot long, will be constructed at the location of existing Locks 4 and will be named Charleroi Locks. The purpose of the new project is to facilitate navigation on the lower Monongahela River. Pittsburgh is currently the second largest inland waterway port in the nation, and the new locks will be an important component of the navigational infrastructure. The existing lock walls are of mass concrete construction and are founded on wooden timber piles driven to rock through alluvial sands and gravels. The new lock walls were designed to be supported by approximately 300 reinforced concrete drilled shafts, varying in diameter from 4 to 6 feet. To handle axial loads, the drilled shafts were designed for end bearing, with some skin friction. The tips of the shafts will be founded within competent rock. Since the walls will undergo lateral loads, the drilled shaft design also had to consider this loading condition. Some of the drilled shafts will be installed within coffer boxes, which will incorporate a tremie concrete seal down to top of rock. Complicating the design even further was the fact that some portions of the new walls will be supported by shafts that extend some 9 feet above top of rock through alluvial soils, producing a cantilever effect. The first phase of the new lock construction was initiated in the summer of 2005 with a contract awarded to replace the river wall. This required shutting down the existing riverside lock chamber and diverting all river traffic to the longer existing land chamber. The foundation of the new river wall will use 144 drilled shafts. To optimize the design embedment of drilled shafts in rock for the river wall, an exploratory drilling program was conducted by the contractor in July and August, 2005. Based on the quality of the sedimentary bedrock, the shafts will be embedded in rock from 31 to 38 feet. To achieve adequate end bearing resistance, the tips of each shaft will extend through predominantly claystones into a more competent siltstone unit for a minimum embedment of one foot. The contractor also performed an exploratory pile driving program to aid in the construction of the drilled shaft casing and the cut off walls that will encapsulate the river wall. Two demonstration drilled shafts located outside the footprint of the new river wall, will be constructed prior to the drilling of any production shafts. The demonstration drilled shafts will verify that the contractor is able to meet the design criteria and quality requirements of the contract. The river wall contract is currently underway and is scheduled to be completed in 2010.

Jan 1, 2006

By Wilbert J. Huff

The organization of the Explosives Division has been outlined in two preceding publications., The activities of the various units for the fiscal year 1939 are described hereafter: I. INFLAMMABILITY OF GASES AND VAPORS DETERMINATION OF EXPLOSION HAZARDS OF COMBUSTIBLE GASES AND VAPORS IN MINES AND INDUSTRIES (a) Determination of Limits of Inflammability of Gases and Vapors The following hitherto unpublished limits of inflammability were determined during the past fiscal year.

Jan 1, 1939