Search Documents

By Ryan W. Ulansky

This paper presents the conceptual design of a magnetically-levitated skip for use in an underground mine. A skip is used to move rock from an underground mine to its surface processing facility. Conventionally the skip is raised and lowered by cables, similar to an elevator. In a magnetically-levitated skip, the cable is replaced with a linear induction or synchronous motor to provide propulsion and levitation. Removal of the cables in a magnetically-levitated skip provides many advantages over a conventional system including the ability: to negotiate corners, to travel vertically in the shaft as well as horizontally to the mining face, and to move a very large volume of material using multiple skips in a small shaft. A magnetically-levitated skip is a safer, more environmentally-friendly, productive alternative to conventional skipping. It has the further advantage to decrease haulage distances for underground vehicles.

May 1, 2002

By Foster Fraas

One of the lithium minerals most widespread in the earth's surface is spodumene (Li2O-A1203-4Si02) a lithium aluminium silicate. For some time, deposits of this mineral were known to exist in the Black Rills of South Dakota, but it was only quite recently that Hess4/ pointed out the great magnitude of the low-grade e deposits it s in North Carolina. The theoretical lithia (Li20) content of spodumene is 8.04 percent. The only other minerals with such high lithia content are the phosphates, but these occur only in pockets and are not in extensive deposits5/. Actually, however, the lithia content in spodumene is never found to be this high, being nearly always below 7 percent for the pure mineral, and part of the lithia is apparently replaced by other alkalies.

Jan 1, 1937

By D. Wolfe, R. Cleminson

"The Aurora North mine has been operating for more than ten years, and is the source of over half of Syncrude’s bitumen production. The slurry systems at Aurora experience high rates of wear, and mission lengths on current slurry pumps are nominally 1500-2000 hours. Recent work has enabled a better understanding of the significant adverse effect of large particle impingement damage to impeller vane leading edges - which is the known life determining issue for Aurora hydrotransport pumps. A new pump design has been developed with a larger diameter impeller and increased vane lengths, and is expected to triple Aurora’s mission length for hydrotransport pumps.INTRODUCTIONSlurry Pumps are Critical Equipment at SyncrudeSlurry pumps are a critical component in Syncrude’s operations. In a typical Aurora application, each pump stage helps move over 8000 dry tonnes per hour of oil sand, plus an equal volume of process water that has been added to create the slurry. The average impeller life in oil sand hydrotransport service at Aurora has been nominally 1500-2000 hours, or 12-16 million tonnes of oil sand pumped. Generally, the slurry pump application at Aurora has proven very difficult to improve due to the unique combination of high sand abrasivity, 125 mm (5”) large particle top size (lumps), and high flow rate relative to basic pump size; a factor that results in higher than optimal impeller vane speeds for the service conditions.PROJECT BASISSlurry Pumps are the Reliability Bottleneck at AuroraSlurry pumps are currently the shortest-lived components that determine the overall system run length at Aurora, in Hydrotransport, Extraction and Tailings. Vibrating screens and piping had been previous bottlenecks, but their reliability has been improved through upgrades in equipment design and wear materials. Both vibrating screens and piping can now achieve 4000 hour mission lengths."

Jan 1, 2013

By D. M. Abbott, H. J. Sandri

The geoscience matrix method has proven useful for valuing metallic mineral properties lacking delineated mineral resources or reserves. However, the method explicitly excludes commodity markets from the factors considered; marketability is assumed. When valuing industrial mineral properties, marketability cannot be assumed, it must considered. Market considerations may also significantly affect the standard weightings of geoscience matrix parameters such as the proximity to known deposits. In some cases, such proximity is desirable but in many cases it is undesirable. Application of the geoscience matrix method to industrial mineral properties therefore requires thoughtful, market-related adjustments to the basic geoscience matrix methodology.

Jan 1, 2000

Duty on Lead Reduced. -On December 28, the President signed H.R. 5047 which reduces the duty on unwrought lead from 3.5% ad valorem to 3% ad valorem, with a floor level of 1.0625 cents per pound, effective retroactively from January 1, 1980, through June 30, 1983. Pacific Northwest Power Bill Passed. -On December 5, the President signed S. 885 which will enable the Bonneville Power Administration to guarantee 20-year contracts to its 15 major industrial customers in exchange for higher rates. In effect, the bill will have industrial customers pay some of the costs of building additional generating facilities in the Northwest, of which thermal units are expected to be a major part. BPA supplies power to six primary aluminum producers which operate eleven plants having over 30% of the primary aluminum capacity in the United States.

Jan 1, 1980

By Alastair C. Torrance

"A brief review of the Australian mining industry is given followed by a more detailed treatment of a study of the influence of primer Size on explosive performance. This is based on a joint research programme conducted by BHP Central Research Laboratories and Dyno Wesfarmers Ltd and examined the effect of the size of cast primers on the run up and steady state detonation velocitiesof ammonium nitrate based explosives as a function of blasthole diameter. The field trials examined a numter of the Dynamo 'Westfarmers HDF series of primers in conjunction with ANFO, emulsion and watergel explosives. Results indicate that the iun up velocity of 187 mm diameter ANFO charges is negligible using cast primers as small as 150g. However, emulsion and watergel explosives did exhibit run up in both 187 and 3:1mm diameter blastholes, independent of the size of primer. This could last from 7 to 10 blashole diameters"

Jan 1, 1991

By CHARLES R. KETES

I. INTRODUCTORY. Lake Valley, New Mexico, has long been one of the most widely known mining districts of southwestern United States. For many years its silver-mines have been among the most famous of the country, visited by many mining men and geologists; yet little information regarding the origin of the ore-deposits and the influencing geologic conditions has found its way into print. With the recent revival of public attention, after a decade and a half of utter stagnation, to the mining of silver in the Southwest, special interest attaches to the genesis and geologic disposition of the ore-bodies which are so finely open to inspection in the Lake Valley district. Moreover, the local features here described are typical of the conditions existing over a much larger field. The fact that the ores are chiefly the chloride and the chloro-bromide of silver adds further interest. Data bearing upon the genesis of haloid ore-deposits are, at the present time, very much sought. Arid regions offer particularly favorable conditions for the formation of such ores. This New Mexican district appears to supply solutions to many problems concerning this class of ores, which have long vexed the student of ore-deposits. II. LOCATION AND HISTORY. The town of Lake Valley is situated in Sierra county, in the southwestern part of New Mexico, and 100 miles northwest of El Paso, as the crow flies.From a mining standpoint, the location of the place is itself suggestive, as it lies on the southeastern slope of the great quaquaversal arch of the Colorado plateau. The center of this vast dome is in north-central Arizona, and radii about 150 miles in length reach its foot in all directions. Around its basal margins runs the broad mineralized belt containing most of the great mines of the Southwest, which extends from south-central Colorado southward and southwestward through New Mexico, thence westward through Arizona, northwestward and northward through southeastern California and western Nevada, and, finally, eastward through Nevada and Utah into Colorado again. This great mineralized belt is important as geographically limiting profitable mining over the greater part of five States.

Jan 1, 1908

By R. A. Cattell

A technologic group such as the Petroleum and Natural Gas Division of the Bureau of Mines, which conducts research on many of the complicated and frequently interrelated problems of extracting crude oil and natural gas from the ground, transporting them to market or to places for subsequent treatment, and manufacturing products, should report progress from time to time. Engineers and others who apply the results obtained by this division are closely associated with its personnel, because may of the problems are attached cooperatively with groups in industry. Some of this cooperation is formal, as exemplified by work now in progress under cooperative agreements with the States of Oklahoma, Kansas, and others, but much of it is informal, prompted by the desire to be mutually helpful in the public interest. Furthermore, the published reports of the Bureau on subjects pertaining to petroleum and natural-gas technology come to the direct attention of a relatively large number of persons, whose interest in results and appreciation of the value of this type of work have caused them to be kept currently informed regarding available data.

Jan 1, 1940

By R. A. Cattell

A technologic group such as the Petroleum and Natural Gas Division of the Bureau f Mines, which conducts research on many of the complicated and frequently interrelated problems f extracting crude oil and natural gas from the ground, transporting them to market or to daces for subsequent treatment, and manufacturing products, should report progress from time to time. Engineers and others who apply the results obtained by this division are closely associated with its personnel, because many of the problems are attached cooperatively with groups in industry. Some of this cooperation is formal, as exemplified by work now in progress under cooperative agreements with the States of Oklahoma, Kansas, and others, but much of it is informal, prompted by the desire to be mutually helpful in the public interest. Furthermore, the published reports of the Bureau on subjects pertaining to petroleum and natural-gas technology come to the direct attention of a relatively large number of persons, whose interest in results and appreciation of the value of this type of work have caused them to be kept currently informed regarding available data.

Jan 1, 1940

Winzes are usually sunk 9 ft. 6 in. long by 6 ft. 0 in. wide and are divided into two compartments, 4 ft. 0 in. by 5 ft. 0 in. inside the timbers. The general practice is to sink the winze to a depth of from 9 to 12 ft., put in bearers and three or four rings of timber, and then erect a sinking headframe before continuing sinking operations.GENERALThe main feature governing the design of the headframe was that all parts could be transported on timber trolleys in No. 2 Shaft. Except for some minor details the structural members consist of steam pipe. Joints are sections of steam pipe welded to one member and into which the other member fits and is held in place by a 1-in. bolt. The headframe consists essentially of two bedpieces to carry the winch and to form a seat for the four legs. The legs support the sheave bearers, the tipping door and the brace.Except during tipping operations the door is in a nearly vertical position. For tipping it is lowered to an inclined position and a hook suspended from one of the bracing members of the headframe is attached to a "D" welded to the bottom of the kibble. This causes the kibble to tip when it is lowered on to the tipping door. The capacity of the kibble is 4 cubic feet.THE HEADFRAMEThe dimensions of the headframe are:Height to top of sheave .. .. 14 ft. 10 in.Distance centre to centre of legs 4 ft. 4 in.Length of bedpieces .. .. .. .. 8 ft. 9 in.The weight is approximately 2,000 lb., the tipping door and bedpieces being the heaviest members. They weigh 240 lb. and 170 lb. respectively.One compartment of the winze is decked over, and the bedpieces, which are 8 ft. 9 in. lengths of 6 in. pipe with three short lengths of plate welded to the underside, are placed over the sinking compartment, either transversely or parallel to the winze. Three 3 inch pipes act as spreaders between them.Welded to the top of each bedpiece is a 6-in. by iHn. plate 3 ft. 0 in. long with four 4-in. by 1.5-in. slots cut longitudinally at 10 in. centres. Two 10 in. by 4-in. timbers are bolted to these plates, the distance between them being adjusted to suit the holes in the winch bedplate, which is bolted to the 10-in. by 4-in. timbers.Two short lengths of 3 in. pipe are welded to each bedpiece at 4 ft. 4 in. centres. These form the seats for the legs of the headframe, which are...

Jan 1, 1941

By C. H. Schack

Extractive metallurgy techniques currently employed to recover silver from primary ores and secondary scrap were reviewed and evaluated to identify and delineate metallurgical problems whose resolution would increase the supply of silver from domestic materials. The survey revealed that practically all primary silver is recovered by froth flotation concentration of various types of ores, followed by smelting and refining of the separate lead, copper, and zinc concentrates. Silver losses during the complex processing are, with rare exception, inconsequential. Furthermore, any silver production gain from base metal ores, which contribute about two-thirds of the total primary silver, is directly dependent no improvement in the market for the base metals. Statistical data on new and old silver scrap are wholly inadequate to make reliable conclusions about scrap processing problems and the possibility of increasing the recovery of silver from the many forms of secondary silver-bearing materials. The available information indicates (1) that efficient silver reclamation practices are employed by the larger users of silver, and (2) that recovery of additional secondary silver involves solution of problems of collection rather than of processing. Several possibilities exist for limited increases in silver production from primary ores by improvement in metallurgical practices. Specifically, research is needed to (1) solve the problem of recovering silver from the copper ores of the Copper Range district, Michigan; and (2) devise economically feasible methods for recovery of silver from presently marginal or submarginal ores char because of grade, location, and frequently complex nature cannot presently be exploited by conventional techniques.

Jan 1, 1965

Stope support systems, typically consisting of props and packs, are used extensively in the gold and platinum mining industry to stabilize the rock mass in the excavation vicinity and to reduce the hazard associated with rockfalls and rockbursts. The design of stope support systems was historically based predominantly on past experience and practices, and cost considerations. The recent development of a new and improved support design methodology, has led to the potential for significant increases in worker safety and support cost savings. This paper reviews some of the fundamental rock mass and support criteria that form the basis of the improved support design methodology. The considered design criteria are the height of potential fall; quasi-static stope closure rates; dynamic stope closure rates; compressive hangingwall stresses; discontinuity spacing, orientation and interface properties; effect of support length (stoping width); effect of compression rate; consistency of support performance; a real coverage; support spacing; and zone of support influence. The proposed support design methodology combines both the zone of influence and key block stability theories, resulting in optimized support systems for rockfall and rockburst conditions. The site-specific methodology consists of two stages: (i) a tributary area analysis, and (ii) a zone of support influence and a stability analysis, considering hangingwall failure due to buckling, shear and block rotation, which gives maximum safe spacing of individual support units. The methodology is suitable for designing support systems for both blocky hangingwalls and hangingwalls fragmented by face-parallel extension and shear fractures.

Jan 1, 2001

By T. A. Muhlare

The use of electrolyte additives to smoothen cathode deposits during copper deposition is practised worldwide. These additives absorb on the cathode surface and take part in the electrochemical crystallization process. However, these additives also affect the quality of the cathodes when they are inadequately controlled. Electrolyte additives used by Palabora are glue, thiourea, Avitone and chloride. Their effects were determined on cathode quality, the size of the current density region that gives the desired compact morphology, and current efficiency. This was done in a small-scale cell. Small cells have different hydrodynamics from industrial-scale cells, which makes it difficult to simulate the operation of industrial cells in a laboratory. The approach used here was to use a rotating cylinder cathode to attain controlled hydrodynamics. The rotation speed was chosen to give a diffusion layer thickness that is similar to that of an industrial-scale cell. It was shown that even fairly small changes in the additive levels can significantly affect the cathode morphology, and the current density range over which this morphology can be obtained. Keywords Copper, electrorefining, glue, thiourea, avitone and chloride.

Jan 1, 2011

By Andrew G. Patton

The Alimak mining method was introduced at the David Bell mine in 1998 to extract an otherwise uneconomic and inaccessible reserve. The success associated with the extraction of these reserves led to major expansion of the method. To date, results have been extremely positive in terms of grade control, reduced dilution, stope recoveries, productivities and mining costs. It is hoped that through further development of the method at David Bell mine we will continue to see positive results in these areas and be able to increase mineable reserves to include proven resources that do not currently meet the criteria of our current stoping plan.

Oct 1, 2001

By Jinwu Kang

The hydraulic turbine blade of the matensitic stainless steel (Cr13%,Ni5%,Mo1%) is a kind of large and curved shape, which is susceptible to deformation in both casting and heat treatment processes. The coupling analysis of heat transfer, phase transformation and stress in heat treatment process of the turbine blade for Three Gorges Project is carried out by using Deform-3D software. Its temperature fields, phase fields and stress fields in heat treatment process are obtained. And its deformation is predicted. In the cooling process of normalizing, the blade exhibits relatively large deformation. Based on the stress analysis and deformation prediction in heat treatment process, an algorithm for the determination of reverse deformation of the blade casting in heat treatment process is presented. And the reverse deformation distribution of blade is obtained.

Jan 1, 2010

By G. C. Sun

Rock mechanics properties, i.e. uniaxial and triaxial compressive strength, indirect tensile strength shear strength, Young's modulus, and poisson's ratio were collected for coal and related strata from 50 coal seams in 90 mines. The methodology of data organization and retrieval is described in details. The values and .ranges of those properties are also discussed.

Jan 1, 1993

By R. Simonson

Agenda ? Need and Introduction ? Interface Management Programs ? Outcomes of Successful Interface Management ? Key Success Factors ? Lessons Learned ? Concluding Remarks Need for Interface Management ? Complex projects ? Larger in scale ? Physically dispersed and delivered remotely ? Involved with several stakeholders ? Risks thus imposed due to: ? Iterative and dynamic nature ? Large information flow ? Document revisions and information updates ? Related sources of Risk: ? Ineffective communication ? Poor work relationships ? Person to job mismatches ? Failure to clarify expectations

Aug 1, 2013

The need for legislative reform of health and safety legislation has been recognised in New Zealand for about a decade. Previous legislation did not cover all work places, many areas were excluded from coverage, and there were at least 14 different acts and dozens of sets of regulations dealing with various aspects of health and safety.

Jan 1, 1993

By N. L. Hayward, V. H. Ness

In the past decade Australia has seen the development, construction and commissioning of three complex processing plants for the treatment of lateritic nickel ores. These have all been based on high pressure acid leaching (HPAL) for extraction of nickel and cobalt into solution, followed by solid liquid separation in a CCD circuit. However, flowsheets for separation and purification of the nickel and cobalt diverge markedly. The existing plants have been commissioned with varying degrees of success, with a variety of problems ranging from materials of construction to inadequate design. While the process problems are not insurmountable, there is much room for improvement. Currently there are several new HPAL plants at the feasibility or financing stage. All of these have adopted one of the existing flowsheets. Most of the enhancements have focused on increasing autoclave size. It is now time to assess the success and failures of the three existing plants and incorporate this experience in a design for productivity, efficiency and reliability. Towards this end, this paper discusses aspects of flowsheet optimization, materials of construction and engineering design.

Jan 1, 2001

By Mohammed Sakr

A Two-Section Helical Pile (TSHP) is a steel pipe with two shaft sections of different diameters and with one or more helix plates near the bottom of each shaft section. TSHPs are used regularly in western Canada as foundation pockets for single and double circuit distribution power line poles. The results of a comprehensive lateral pile load test program and the field monitoring of TSHPs installed in organic soil (muskeg) over soft clay are presented in this paper. A total of nine full scale lateral load tests were carried out, including seven tests using TSHPs with different diameters and embedment depths, and two tests using one-section helical piles. The prime objective of the study was to evaluate the lateral resistance of TSHPs installed into very soft organic soil (muskeg) overlying soft clay soils, to compare their lateral resistance relative to one-section helical piles and to compare the measured and the estimated lateral resistances using p-y curves. In order to provide sufficient soil data for analysis, the subsurface soil stratification was evaluated using two different techniques including; Cone Penetration Tests (CPT) and Portable Soil Probe Tests (PSPT). The two testing techniques were also compared and evaluated. This paper summarizes subsurface soil conditions, pile configuration, helical pile installation procedure, testing setup and results.

Jan 1, 2009