Search Documents

By J. E. Tress

The Bureau of Mines prepared submicron tungsten powder by reducing tungsten hexachloride with hydrogen. The particle diameters of the resulting tungsten powders ranged from 0.015 to 0.046 micron. Within the limits of the variables investigated, no clear-cut correlation was found between process conditions and final size of the powder. Oxygen was the major contaminant in the product; being present both as an adsorbed gas and as suboxides of tungsten. Studies showed that the powder yielded compacts of approximately 45 per-cent of theoretical density when compacted mechanically. Low-temperature sintering produced more rapid densification in these compacts than in compacts prepared from conventional powders. Adding up to 20 percent ultrafine powder to conventional tungsten powder caused an increase in density upon compaction with maximum densification occurring at approximately 12 percent ultrafine powder.

Jan 1, 1966

By W. S. Hegler

Introduction The San Antonio mine is on the north shore of Rice lake, thirty miles east of lake Winnipeg and 120 miles northeast of the city of Winnipeg. Since production was started in 1932, about 2,000,000 tons of ore have been mined. Currently in progress is an extensive development programme which involves 11,500 feet of crosscuts, 3,800 feet of raises, 1,753 feet of shaft sinking, and 160,000 cubic feet of slashing, all in footwall waste rock. It is the purpose of this .paper to indicate the necessity for this work and to describe the methods employed to carry it out. Where unknown factors are as prevalent as they are in the average Canadian gold mine, a definite answer cannot be given as to what is the most economical and efficient system for mining dipping deposits. At San Antonio, the host rock for the orebodies, locally termed basalt, occurs as a sill some hundreds of feet in width and dipping at approximately 45 degrees from surface to an unknown depth. It may be assumed that it continues well below the lowest depth established to date by diamond drilling. At present, a vertical winze (No. 3 winze) hoists the ore from the 2,360-foot level to the 1,600-foot level, on which it is hauled about 900 feet to No. 3 shaft, also vertical, and there hoisted to the mill bins on surface. To maintain ore reserves at a five-year figure, at full production, additional deep exploration was required immediately. It was decided to sink No. 4 winze, a vertical opening of the same size as the other operating shafts, to provide ten additional levels (17 to 26) at 150-foot intervals, with additional depth to allow for an underground crusher installation and usual loading-pocket facilities for three-ton skip-hoisting. The winze was bottomed at 1,753 feet below the collar, at a depth of 4,117 feet below surface, and is the deepest man-sized opening in Manitoba.

Jan 1, 1949

By Ernest E. Berger

"INTRODUCTIONOne of the outstanding problems in the normetallic industries, and one which involves two of the greatest of these industries, cement and gypsum, is the reaction of Portland cement with calcium sulphate. To all Portland cement clinker there is added in the manufacturing process, a small amount of retarder, as a necessary ingredient of the finished product. This retards the initial set, increases the strength, and adds to the plasticity of the cement so it will have the desired working and setting qualities. The retarder commonly used is gypsum, (CaSOA.2HO), which is the hydrous form calcium sulphate. Calcium sulphate is also available as plaster of Paris (CaSO4 1/2 HC) and anhydrite (CaSO4). The purpose of this inquiry was to determine the form or mixture of forms best adapted for retarder. The problem is complicated by the fact that cement clinker is a complex mixture of calcium silicates and aluminates, and that clinker from different mills, making cement of approximately equal quality, differs considerably in chemical constitution. Thus the same retarder may give very different results with different types of clinker, especially in the percentage of retarder required for the same degree of retardation.It has been known for some time that a small percentage of plaster of Paris will greatly retard the time of set of Portland cement as well as increase its strength and plasticity, but whether gypsum and anhydrite will have a similar effect is as such disputed question. The offects of gypsum have received little consideration in laboratory research because, even though it will not retard a clinker when the two are mixed in the laboratory, as has been noted in some instances, the cement will have a normal set when the two arc mixed in the large tube mill at the plant, so that practically, gypsum seems to be equally as goou as plaster of Paris, and because of the great saving in cost it has been used almost exclusively."

Sep 1, 1925

By Edna A. Dancy, Gerhard J. Derge

The specific conductance of FeOx,-CaO melts in contact with iron was found to decrease from 200 ohm-1 cm-1 for FeO, to 40 ohm-1 cm-1 for a melt containing 26.3 pct CaO at 1400°C. The temperature coefficient was positive at all compositions, but became smaller at high CaO contents. Current efficiencies for electrolysis increased from 2.5 pct in FeOx to 17.3 pct at the high CaO composition, indicating a change from predominantly electronic conduction to conduction with a substantial ionic contribution. It was shown that Ca++ ions as well as Fe++ ions carry the ionic current. A subsidiary investigation on the apparent effect of atmospheres of argon, helium, and nitrogen on the electrical conductivity showed that this could be correlated with surface temperature losses, which varied with the thermal conductivities of the gases and resulted in precipitation of metal by the reaction 3 Fe++ = 2 Fe+++ + Fe. The work described in this paper is offered as a contribution to the general fund of knowledge concerning metallurgical slags. Measurement of electrical conductivity and electrolysis are comparatively trouble -free methods for investigating molten materials, but, although these methods had been used for complex slags, it was not until the work of Bockris et al.1 that the approach of examining simple binary slag systems was employed, and CaO-SiO2, MnO-SiO2, and Al2O3-Si9 were studied. Two groups have performed work of particular relevance to the present investigation. Inouye, Tomlinson, and chipman2 studied the conductivity of wustite as a function of temperature and of the addition of 5 mol pct of a number of oxides, including CaO. They concluded that molten FeOx in equilibrium with iron is a semiconductor. Simnad, Derge, and ceorge3 demonstrated the ionic nature of liquid iron silicate slags and also concluded that, although the conductivity of FeOx in equilibrium with iron is predominantly electronic in nature, there is a small ionic contribution. The work reported here on FeOx,-CaO slags consists of three main parts, namely, the determination of the specific conductance over a wide composition range, an investigation into the nature of the conductivity through current-efficiency measurements over the same composition range, and an attempt to identify the current-carrying ions, as well as a subsidiary investigation on the apparent effect of the nature of the inert atmosphere on the conductivity. EXPERIMENTAL Materials. The slags, varying in composition from FeOx to 27 pct CaO, were prepared by heating reagent- grade Fe2O3 in an ingot iron crucible with a suitable amount of CaCO3 and, in some cases, powdered iron, in air. This prefused material was then used for the runs. At the end of each run the cell was removed from the furnace and quenched by immersing the bottom half in water. After crushing, the slags were analyzed for calcium and total iron by the usual wet methods. The oxygen content was obtained by difference. Specific Conductance: Apparatus and Method. Fig. shows the experimental setup, with the conductivity cell and leads of ingot iron. The standard four-probe method for measuring high conductivities was used. In this, the potential drop across the unknown resistance is compared with the potential drop across a known resistance connected in series, i .e., same current through both resistances. Thus there are both current and potential leads to the center electrode and to the crucible, which acts as th other electrode. Both ac and dc circuits were available for the measurements; they have been described in earlier work performed in this laboratory.4,5 The geometry of the cell was such that the center electrode was equidistant from the bottom and sides of the crucible. This ensured that the current path was the same irrespective of the magnitude of the conductivity of the material in the cell. Cell constant were measured with KC1 or NaCl solutions, which have considerably lower conductivities (0.0013 to 0.25 ohm-' cm) than the slags, and this precaution in design made sure that the determined cell constants applied to the cells with contents of any conductivity. The cell-constant determinations were made with the ac measuring circuit to prevent polarization. The four-probe method eliminates lead resistance but not the resistance of those parts of the center

Jan 1, 1967

By Michael B. Tessieri

With the increasing environmental demands and higher fuel efficiency standards on auto manufacturers, the use of aluminum in automotive applications is expected to show significant growth for the balance of this decade. Cast and wrought aluminum usage is reviewed by auto part, and alloy family for the year 2000 automobile. The analysis addresses the effect of this increased volume on the recycling infrastructure and identifies issues and opportunities, which will face the recycling industry.

Jan 1, 1995

By Michael E. Henderson

The U.S. Bureau of Mines (BOM) constructed the Hydraulic Transport Research Facility (HTRF) to investigate the hydraulic parameters relating to the transport of coarse coal. To achieve these goals in a timely and efficient manner, the Bureau contracted to Boeing Services International, Inc. (BSI) the responsibility of operating the HTRF and providing technical support. This data report is a summary of the testing and data results for the period from 16 September to 1 November 1983. The testing covered herein is for coarse 2-in by a (minus 50 mm) Pittsburgh Seam coal in a 12-in (3 00 mm) pipeline, at velocities ranging from 5 to 18 ft/s (1.5 to 5.5 m/s) and at concentrations ranging from 15 to 55 pct.

Jan 1, 1985

By Wesley Alves Quintão

O projeto criado e aqui apresentado teve por objetivo atender as necessidades da empresa em relação às metas de economia de energia e adequação ao mercado atual e para isso foi estudada uma maneira de gerar economia de gás com o desligamento de pilotos de ignição e também eliminar atrasos mecânicos no processo de acendimento, purga e estanqueidade do forno de reaquecimento Stein, através do uso de recursos da automação, eliminando dispositivos eletromecânicos garantindo velocidade de informação, economia comprovada de gás e maior confiabilidade no sistema de monitoramento do processo.

Aug 17, 2017

By Kássio Nogueira Cançado

Para resfriar as barras de aço após o processo de lingotamento contínuo, são utilizadas estruturas chamadas de bolsas de aciaria onde as barras são armazenadas, empilhadas em conjuntos de XX até YY barras. Essas bolsas tem por finalidade permitir o resfriamento lento das barras e assim melhorar a qualidade metalúrgica do material. O estudo feito teve como objetivo criar uma ferramenta computacional capaz de simular o perfil de resfriamento dessas barras, ajudando na tomada de decisão no ambiente industrial. O modelo desenvolvido permite a simulação de varias situações de carregamento, várias dimensões e tipos de barras. Os resultados obtidos foram validados numericamente com o modelo desenvolvido por SILVA [1] que já estava validado com testes experimentais. O erro relativo ao modelo existente foi de aproximadamente 2% o que valida os resultados e a deixa a ferramenta apta a ser utilizada no ambiente industrial. O modelo permitiu um melhor planejamento da produção, representando um potencial de ganho de 12 horas em 72 horas de produção.

Aug 17, 2017

By Tomek Ulatowski

INTRODUCTION In 1974, Industrial Miners Mexico, S.A. (IMMSA), agent for the borrowers, was the largest privately-held mining, smelting, and refining company in Mexico (accounting for 32% of Mexico's nonferrous metal and coal production in 1974), the fourth largest company in terms of sales, and the second most profitable company in Mexico, excluding government wholly-owned and operated industries. The company was engaged in the mining, smelting and refining of coal, copper, fluorite, gold, lead, silver, zinc and related by-products for domestic consumption and export. A combination of favorable factors led IMMSA to propose an investment plan amounting to US$286 million for 1974 through 1978, of which US$150 million was to be financed. These factors included: Substantial profits in 1973 and 1974 Positive near-term outlook for metal prices Success of the reinvestment program in increasing productivity Substantial additions to proved reserves during 1973-1974 and Fiscal incentives provided by the Mexican government to stimulate investment in the mining industry. The primary purpose of the investment program was to construct a new electrolytic zinc refinery and to expand and modernize many of the company's existing mining and refining facilities. THE BORROWER Company History Compania Miners Mexico, S.A. was incorporated in the city of Monterrey in 1918 as a wholly-owned subsidery of ASARCO Inc. (formerly American Smelting and Refining Company, New York) for the purpose of mining and processing non-ferrous metals and related products. In compliance with the Government's Mexicanization program, ASARCO Inc. divested itself of 51% of its equity in Compania Miners Asarco, S.A. on June 30, 1965. Subsequently, ownership in the divested share was apportioned as follows: 15% ownership in Compania Miners Asarco, S.A. to a group of private investors, and 36% in trust for subsequent public sale. The company's name was changed to Asarco Mexicana, S.A. in 1965. Mexican ownership in Asarco Mexicans, S.A. was increased to 51% in 1967, following the purchase of the 36% share ownership held in trust, and then to 66% in 1974 when ASARCO Inc. divested itself of an additional 15% of its holdings in Asarco Mexicans, S.A. Following its 1974 divestiture of 15% of Asarco Mexicans, S.A., ASARCO Inc's ownership in Asarco Mexicana, S.A. was reduced to 34%. In 1974, the company changed its name for the second time to Industrial Miners Mexico, S.A. (IMMSA). Fiscal Agreement IMMSA entered into a fiscal agreement with the Mexican government in 1969. The agreement, which was renewed in 1974, provided for 100% of the production and export tax corresponding to the federal government with a minimum of 50% of the amount refunded to be reinvested in fixed assets. Further, the agreement permitted the company to

Jan 1, 1985

By Gilles Cachia, Foteini Vasilikou, Seth Pollak, Hannes Lagger

"INTRODUCTION The Shatin to Central Link (SCL) is a new rail line being constructed by the MTR Corporation for the Government of Hong Kong to cater for the growing passenger demand between the North-East New Territories and the urban areas of the city. Contract 1103, which will provide the 4 km of running tunnels between the new Hin Keng and Diamond Hill Stations, was tendered in a design-build framework and awarded to Vinci Construction Grands Projets (VCGP) in October 2012, with Arup as Vinci’s lead designer. One of the most challenging pieces of work on the contract involved the construction of 133m of SEM mined tunnel on the northern end of the project. The Northern Mined Section (NMS) is an undrained, twin-track, single bore profile, broken out through the southern pipe pile wall of the Hin Keng Station cut-and-cover box, Figure 1. The tunnel has maximum excavated dimensions of 14.5m span x 12m height, with track spacing of 6.175m. The general excavation sequence consisted of 3 stages; a 6m high top heading (73.1m2), followed by bench (27.3m2), and invert (26.7m2). A risk-based approach to the design was taken given the large variation in rock level, cover, and an active stream course above tunnel crown. Ultimately, six different temporary support types were utilized in order to optimize the construction process through continually changing ground while maintaining a safe and stable excavation. Three main support types were developed during the initial design phase, along with a “contingency” case, which utilized a partial heading excavation sequence and enhanced face support. The purpose of the contingency support type was to have a robust, engineered design available for immediate implementation should unexpected ground behavior develop, leading to the breaching of instrumentation trigger levels. This support type was never implemented on site. Drill- and-blast tunneling commenced once 6m of rock cover was verified through forward probing. A robust instrumentation and monitoring scheme provided valuable data throughout excavation and the means to carry out a geotechnical back-analysis of the ground behavior and support performance."

Jan 1, 2016

By Joaquim Luiz Monteiro Barros

O atendimento as normas ambientais vigentes nos diversos processos das siderúrgicas no Brasil, mais do que uma exigência legal, deve ser um compromisso da empresa com os funcionários, clientes e com a sociedade como um todo. O perfeito dimensionamento do sistema de limpeza de gases e a aplicação de filtros de mangas horizontais é, com certeza, uma alternativa eficiente para solucionar de forma adequada as particularidades e necessidades dos diversos processos siderúrgicos.

Aug 17, 2017

By John R. Reeves

The data presented in this paper form the chief part of a general survey of the oil-shale resources of Indiana. Other papers* have already been published which contain data an various aspects of this resource. In combination, these papers present data with reference to the following points; (1) distribution of the New Albany shale; (2) amount of shale available; (3) homogeneity and thickness of the formation; (4) amount and quality of the oil obtained from the shale; (5) nitrogen content of the shale; (6) extractibility of the shale and its amenity to breaking; (7) some economic factors bearing upon the utilization of the shale; and (3) other miscellaneous factors and data. In the future, technical work on other phases of the general problem is expected to be done with the object of making a complete survey of this resource which is of much potential importance to the state and nation.

Jan 1, 1923

By Aprígio Ângelo de Jesus

No presente trabalho, foram avaliados os efeitos do tratamento térmico de alívio de tensões na microestrutura e propriedades mecânicas de juntas soldadas dos aços SA516-70 e SA387-11 (ambos aplicados na fabricação de vasos de pressão). Chapas com 40 mm de espessura de ambos os aços foram soldadas por arco elétrico com arame tubular e, posteriormente, submetidas a tratamento térmico para alívio de tensões. A variação de dureza ao longo da solda e a resistência à tração dos materiais soldados e tratados termicamente foi avaliada. A microestrutura dos materiais soldados foi acompanhada por microscopia ótica convencional. Por meio do tratamento térmico empregado foi possível observar a redução do nível de encruamento nos metais base e zonas termicamente afetadas das juntas em ambos os materiais com aumento de ductilidade no aço SA516-70.

Aug 8, 2018

By Charles A. Kliche

INTRODUCTION The Northern Great Plains Coal Province which occupies approximately 36.6 ha contains about one-half of the nation's total coal resources. About one million ha are underlain by coal that is considered to be mineable from the surface. The topography of the province is predominately plains, rolling hills, and some badland areas characterized by breaks or sharply eroded hills. Elevations range from about 1500 m above sea level on the west to about 600 m above sea level on the eastern boundary. The average slope of the ground is approximately 2 m per km. Streams in the province drain generally easterly and southeasterly (1). In the United States, the Northern Great Plains Province lies within the states of North Dakota, South Dakota, Montana, Wyoming, Nebraska, and Colorado. The coal within the province is located almost entirely in the states of North Dakota, Montana, and Wyoming. Although it is relatively low rank, the coal within the province encompasses a large portion of the total remaining U. S. reserves. The U. S. Geological Survey estimates the total remaining coal resources of the United States to be 2.6 trillion mt within 1000 m of the surface, and 2.9 trillion tons within 1830 m of the surface. Of this total, only about 177 billion mt are classified as reserves meaning that they are (1) known in location, quantity and quality from geologic evidence supported by engineering measurements, and (2) economically recoverable based on currently available technologies and current market value (2).

Jan 1, 1983

By M. H. Kline

Round Mountain is one of a number of locations investigated by the Bureau of Mines in its search for manganese deposits during the early phases at the strategic minerals program. The Suiter mine, on Round Mountain, had provided some 5,000 tons of manganese concentrates during the period 1917 to 1919, and early in 1941 prospecting by the Virginia Hardwood Lumber Co. in this same area had discovered manganese on what later became known as the Hall Pit. These promising indications encouraged the Bureau to begin an exploration project in search of additional reserves of manganese on Round Mountain in January 1942 (fig. 1).

Jan 1, 1948

By W. J. McConnell, C. P. Yaglaglou

"IntroductionThis paper on the kata thermometer is issued by the Bureau of Mines on account of the general interest in this instrument and the fact that it is frequently used in studies of mine ventilation conditions with regard to comfort and health of miners. It has been used in the studies being conducted along this line by the Bureau of Mines on the effects of high temperatures and humidities of air in mine working on the comfort conditions, as well as in studies of atmospheric conditions in mine, railway and vehicular tunnels.The study of the various physiological responses of the human body to different degrees of temperature combined with different percentages of relative humility in still and in moving air, now being conducted at the Pittsburgh experiment station of the bureau in the research laboratory of the American Society of Heating and Ventilating Engineers, cooperating with the Bureau of and the U. S. Public Health Service, presents an added opportunity of investigating the instruments that have been devised to measure atmospheric conditions as they affect the comfort and health of human beings.The ordinary mercury thermometer, as pointed out by Heberden3 almost hundred years ago is a very inadequate instrument for measuring the physiological effects of atmospheric conditions. It merely accounts for that part of the body heat lost by raliation and convection, while as a matter of fact greater part of the body heat resulting from the metabolic process within the body is eliminated by means of evaporation from the surface of the body."

Jan 1, 1924

By Ralph H. Whaite

In undermined urban areas, new solutions to subsidence problems are being sought. The Bureau of Mines is investigating a hydraulic backfilling technique whereby fill material is pumped as a slurry through a closed system and widely distributed in inaccessible mine workings from a single borehole. A full-scale demonstration was completed in 1973 in Scranton, Pa., which is underlain by abandoned anthracite mines in several coalbeds superposed one above another. A 30-acre residential area was stabilized by injecting about 450,000 cubic yards of crushed mine refuse into two coalbeds through five injection boreholes. Nearly 200,000 cubic yards was injected through one borehole from which the material moved into the mine workings on all sides; the injected material reached a maximum lateral distance of 640 feet and filled mine openings from floor to roof. In the gravity-feed method formerly used to backfill inaccessible mine workings, quantities of fill injected per borehole averaged about 300 cubic yards. The gravity-feed method required many closely spaced injection holes and provided incomplete filling. The new method, designed for inundated mines, proved successful also in mine workings about mine-water pool level. Distribution of slurry through a buried pipeline minimized disturbance to the community.

Jan 1, 1975

By D. J. Donaven, Manuel Gomez, W. S. Landers

Bulk density tests were made on a Western U.S. coke oven plant blend to obtain bulk density control data that would be directly transferable to plant practice . Maximum bulk density values were obtained at zero surface moisture . Increase in surface moisture to about 6 percent decreased the bulk density to a minimum value . Increase in the fine grinding of the blend , at constant surface moisture , decreased the bulk density . The effect of oil on bulk density was observed with five oils at concentrations ranging from 1/8 to 1-1 / 2 gallons per ton . Maximum bulk densities were obtained within the 1 / 2- to 1 - gallon - per - ton range . Essentially the same bulk densities were obtained with petrolatum- and nonpetrolatum- containing oils . Storage effects were observed on samples tested at selected intervals from 0 to 56 days . No significant change in bulk density took place if no surface moisture was lost during storage .

Jan 1, 1964

By M. Ribeiro, P. So, P. Wong

Electrowinning is a process by which metals, such as copper or nickel, are recovered from aqueous electrolyte solutions resulting from the extraction of the metal ion from an acidic or basic leach solution. The electrolyte or “pregnant” solution is customarily forwarded to an electrowinning "tankhouse." In the tankhouse, the metal ions are deposited on cathode plates by electrodeposition and then recovered from the cathode plates. Other processes may be employed with other metals, such as nickel, zinc, among others, to produce an electrolyte from which their respective metals are obtained. During the electrowinning (electrodeposition) stage, elemental metal is plated out at the electrowinning cathode and oxygen evolves at an insoluble anode. The evolution of oxygen gas forms bubbles which entrain strong acid electrolyte, carrying it into the air above the electrowinning tank in the form of a fine mist or spray when the bubbles break. An acidic mist is generated above the electrolyte. This mist or spray then spreads throughout the electrowinning tankhouse. The acidic mist is corrosive and a health hazard and can cause extreme discomfort to the skin, eyes, and respiratory systems of tankhouse workers, especially during hot weather conditions. Polyfluoroalkyl based products (PFAS) have been widely applied as anti-misting agents in the electrowinning of metals in an acidic electrolyte. Functionalized PFAS compounds, however, have come under increased scrutiny by the EPA due to their impact on human health and the environment. There remains need for improved acid mist suppression agents for electrolysis and electrodeposition, particularly for products free of fluoroalkyl components.

Feb 1, 2023

By Leandro Gusmão da Silva

Neste trabalho, foram estudados os efeitos da irradiação de uma superfície polida do aço inoxidável tipo ASTM F138 com laser de pulsos ultracurtos. As irradiações foram realizadas variando-se a velocidade de varredura do laser, ou seja, a taxa de sobreposição espacial de pulsos. Foi observado que após a irradiação houve uma visível mudança na coloração da amostra. Também foi verificado que com o aumento da taxa de sobreposição de pulsos a superfície tendeu a tornar-se preta, ou seja, absorvedora de luz. Com essa técnica, pode-se realizar marcações com alto contraste sem que haja formação de camadas de óxidos, nitretos ou alterações microestruturais no metal, o que é importante para um material com a precisão que um implante exige.

Aug 17, 2017