Search Documents

By Y. Obara, A. Sato

"Limestone is one of the most important mineral resources, and in Japan it is only one mineral which can be fully supplied by the domestic product. Generally limestone mines in Japan located at mountainous regions, and the combination between bench-cut method and the carry-out system using vertical shaft is widely used in the domestic mines. During mining operations, the occurrence of the blockage in the vertical shafts is very serious problem. Once the blockage in the shafts is occurred, a lot of works and dangerous procedures are necessary to solve the problems. It is thought that blockage is influenced by the cohesion and friction coefficient due to clay minerals thrown into the vertical shafts, however, the quantitative and precise reason is not revealed yet.In this study, the process of blockage occurrence was simulated by 2-Dimensional Discrete Element Method (DEM). In the 2D-DEM analysis, discontinuous circular particles are generated, and the individual movement of each particle is calculated by forward difference method. In the analysis, several typical ore distributions are applied, and the DEM analysis was conducted under the various combinations of cohesion and friction coefficient. From analytical results, it was found that the friction coefficient strongly influences to the occurrence of blockage and there were a threshold values which blockage does not occur. Several kinds of shaft shape were also simulated towards different ore size distributions, and those influences to the blockage occurrence were also discussed."

Jan 1, 2015

By D. A. Jacobson

Mining operations, whether new or existing, are constantly looking for ways to maximize production and improve energy efficiency, while keeping the footprint required to a minimum. The Nordberg MP1250 cone crusher was designed with these three goals in mind. A series of side-by-side evaluations comparing an MP1250 to an MP1000 were completed at two Freeport-McMoRan operations. The first evaluation began October 2009 in a tertiary position and the second began March 2010 in a secondary position, where it remains in full production today. Utilizing 25% higher power capacity than the existing MP1000 tertiary crushers, the MP1250 had 29% higher capacity and 17% lower specific energy, adjusted for differences in feed and product size. The MP1250 compared to the existing MP1000 secondary crushers achieved 30% higher capacity at a slightly reduced specific energy, while achieving a finer product. The MP1250?s higher capacity and energy efficiency may have application in many crushing plants. Depending on site specific economic factors, greenfield projects may benefit from a smaller footprint and less ancillary equipment, whereas brownfield projects may benefit from higher capacity or a finer product within the same footprint.

Jan 1, 2012

By Carlos Alberto Perim

Durante o lingotamento contínuo de placas de aço, muitas vezes ocorre uma queda acentuada de temperatura ao longo do processo. Fatores como o tempo de lingotamento, o superaquecimento inicial da panela de aço, a presença de cascão na panela, entre outros, podem alterar significativamente a taxa de queda de temperatura, levando muitas vezes à interrupção prematura do lingotamento. Neste trabalho, será mostrado o desenvolvimento de um modelo de predição de temperatura ao final do lingotamento de uma panela de aço. Este modelo permite antecipar, com razoável nível de incerteza, a temperatura final do aço no distribuidor durante trocas de panela, de forma que forneça subsídios para a tomada de decisão sobre a interrupção do lingotamento, ou a antecipação de abertura de panela com retorno de aço. Desta forma, o índice de trabalho das Máquinas de Lingotamento Contínuo (MLC’s) da ArcelorMittal Aços Planos América do Sul seria maximizado, e com possível melhoria no Rendimento de Aço. O modelo se encontra em fase de implantação e validação na MLC#3, onde foram definidos parâmetros com critérios de decisão de interrupção/antecipação de troca de panela.

Aug 17, 2017

By Lois G. Schwarz

I did a project (Sungai Piah) as a consultant to your firm in Malaysia, where we were faced with a similar situation as sketched out in your question. The following is what we did for the grouting of the primary holes, which were both located upstream of the plug as well as downstream: We used a hydrophobic MDI based semi-rigid polyurethane prepolymer in the first phase of the grouting operation when grouting under water flow conditions. Then in the second phase and also for the contact grouting we used a two component water compatible polyurethane elastomer. And then for deeper formation grouting, when all the water flow had been stemmed in the vicinity of the plug, we used a regular (balanced stable) cement based grout. So it may not exactly answer your question, but we first used hydrophobic grout because it is very efficient to grout a formation through which water flows. We didn't stop all the leaks day-lighting downstream of the plug or all water running through the formation near the plug, but the flow of water through the rock formation adjacent to the plug was reduced by 99.9%, after completing the urethane grouting. This facilitated the placement of cement based suspension grouts without wash-out.

Feb 10, 2003

C. W. GOODALE, Butte, ,Mont.-While there are many points in Mr. Read's, paper which I am not prepared to discuss thoroughly, I am inclined to believe that difficulties are involved in the establishment of all employment bureau, which shall have exclusive control over the employment and discharge of workmen. I suppose you .have heard a great deal: about the so-called "rustling card? at the works of the Anaconda company. That is a very innocent sort of card, although the I. W. W. organization has made a great deal of noise about it. An applicant for a job is handed a blank on which he tells his nationality, his age, whether married or single, and the place of his last employment. The company then writes to the place where he says he was last employed to find out whether he is telling the truth; we do not ask the previous employer whether the man is blacklisted or has anything; against his record; but simply, "Was this man formerly in your employ?" A great hullabaloo has been made, about this practice by some of the men in Montana who are afraid, of their own records; but out of 53,000 applications for employment received by the Anaconda company since the employment bureau was formed, only 647 were rejected, which does

Jan 1, 1918

By Xavier B. Starnes

"INTRODUCTION The Krausse Estate property was the site of the first lead silver mining in western Kentucky, which began with the sinking of the Andrew Jackson shaft in 1835 3/. The earliest miners considered fluorspar of no value and threw it upon the waste dump, but Crittenden County later became an important part of the western Kentucky and southern Illinois fluorspar district 4/, which has produced about 90 percent of the fluorspar mined in the United States. By 1945, approximately 35,000 tons of fluordpar ore had been produced from the Estate property.This property can be reached by traveling west from Marion on Highway 60 from 2.5 miles, than northward 3 miles. The road from the paved highway to the mines is very rough but not impassable even in bad weather. Ore is hauled 5 1/2 miles by truck to custom mills at Marion, a town of 2, 000 population, where the Illinois Central Railway was a freight station.Hurricane Creek runs through the eastern part of the property. The surface slopes steeply upward to west from the creek, and the topography is rough. The top of the hill is about 150 feet above the creek.The climate permits working throughout the year, but spring rains cause surface water to enter mine and water apparently drains southward along the fractured fault zones, so that when no water is being pumped at properties north of the Krausse Estate a heavy flow comes on the Krausse."

Sep 1, 1946

By Paulo Sérgio Moreira, Geraldo Lúcio de Faria, Rhelman Rossano Urzêdo Queiróz, Amanda Aparecida Fátima Arruda, Ana Cecília de Carvalho

O aço inoxidável ferrítico 410D (UNS S41003) é um aço relativamente novo e ainda em desenvolvimento no mercado Brasileiro. Ele tem sido posicionado como um candidato a substituir aços baixo carbono comuns e aços patináveis em algumas aplicações onde existam exigências no que diz respeito à resistência do material à oxidação e à corrosão. Entretanto, ainda existem algumas lacunas de conhecimento a respeito do seu comportamento mecânico que permitam avaliar a viabilidade de sua aplicação em condições agressivas de trabalho, como por exemplo em temperaturas relativamente elevadas. Partes estruturais de caldeiras, tubulações para condução de vapores e gases quentes, entre outros, são exemplos em potencial para aplicação do aço 410D. Nesse contexto, o presente trabalho avaliou o comportamento do referido aço quando submetido a ensaios de tração a quente nas temperaturas de 300°C e 600°, comparando-se os resultados obtidos com o seu desempenho à temperatura ambiente. Concluiu-se que o aço inoxidável 410D é susceptível ao fenômeno de envelhecimento dinâmico na temperatura de 300°C, tendo sua capacidade de deformação plástica significativamente diminuída. A 600°C observou-se uma diminuição de 45% no seu limite de escoamento e um aumento de 7% no alongamento total em relação à temperatura ambiente.

Oct 8, 2019

By Bruno Miotto, Rômulo Faria, Juliano Tessinari

Water has become a scarce resource in quality. Companies in the ornamental stones sector use water intensively in their processes. Given the current situation, it is imperative to rationalize this feature that at first is related to the reduction of consumption, through no waste. Considering the importance of environmental preservation of this resource and also to comply with the legislation that governs the procedure for processing of ornamental stones, new alternatives should be available for the maintenance of current activities and promoting the development / growth of the sector on the principles of environmental sustainability and economic in future scenarios. The ornamental stones processing industries, especially for micro and small enterprises, require the implementation of a management program that optimizes the use of this feature, since the techniques individually processed operate with three basic processes dependent on water use: split blocks, polishing and finishing slabs. This technology requires a large volume of water resources and control measures involving operating recirculation water can minimize power consumption, making the company more profitable and sustainable. This is a survey of literature, associated with technical reports provided by partner companies and government agencies. This study aimed to the organization and provision of theoretical knowledge about the subject matter coupled with management practices, which may be reproduced or re-purposed in ornamental stones processing companies. It should be noted that the industry in question is lacking in technical expertise for the implementation of sustainable attitudes relevant to water reuse.

Jan 1, 2014

By Shamim A. Dar, & Samsuddin Khan, & K. F. Khan, Mohd Shuaib

The Late Paleocene–Middle Eocene phosphate nodules of Solan District of Himachal Pradesh belong to green facies of Subathu Formation of Sirmur group. Field observations indicate sporadic distribution of phosphatic nodules in the yellow brown to rusty brown, buff-colored bleach shales. Phosphatic nodules are dull earthy to dark grayish in color and break with sharp and conchoidal surfaces. Studies of phosphatic nodules using petrological microscope, X-ray diffractometry, and scanning electron microscopy (SEM) attached with energy dispersive X-ray (EDX) reveal that cryptocrystalline apatite (fluorapatite) is the dominant phosphate mineral. Silt sized silica is the dominant gangue, whereas pyrite and muscovite are present as minor gangue. The phosphate minerals occur as oolites, pellets, and cryptocrystalline apatite in the groundmass. Silica veins form a network replacing the original phosphatic matrix. Brown to brownish black color may be attributed by the organic matter in the phosphatic nodules. Completely phosphatized radiolaria and partially pyritized planktonic foraminifera are observed. There is corroboration of organic matter in the form of microbial filaments in the groundmass of apatite. The findings in the present investigation indicate that the different forms of the minerals, their texture, and distribution in the phosphatic nodules might be due to environmental vicissitudes in oxidizing to reducing conditions followed by replacement processes. Presence of microbial filaments may be due to the active role of microorganisms during the formation of these phosphatic nodules.

By Bruce R. Lipin

Chromite, the only ore of chromium, occurs almost exclusively in mafic-ultramafic rocks and their weathering products. However, not all kinds of mafic-ultramafic rocks are favorable hosts for possible low-grade chromite deposits. For instance, chromium-bearing basalts are not favorable because they commonly contain <0.3% Cr203, and chromite is almost always less than 50 mp in diameter, if it is present at all. Chromite-bearing ultramafic rocks in stratiform and alpine complexes tend to be either ore grade (>25% chromite) or very low grade (<2% chromite); intermediate rocks are scarce. In most complexes, large tonnages exist only in the <2% chromite rocks and the composition of the chromite in those rocks may be unsuitable for metallurgical use. Some nickel laterite districts contain more than lo8 tons of material with 2.0 to 5.5% Cr203, and hence, chromium could be a byproduct of nickel in some laterite districts. In addition, some chromiferous sand placers may contain tens to hundreds of millions of tons of material between 2 and 5% Cr203

Jan 1, 1983

By M. L. Fuller

OWING to the nature of the die-casting process, freshly cast alloys are undoubtedly not at equilibrium from the standpoint of alloy phase relationships. After casting, therefore, they tend to undergo phase changes, with the ultimate effect of reaching a state of equilibrium at the aging temperature, beyond which no further change takes place. This phase alteration undoubtedly is one of the primary causes of the changes in dimensions and physical properties that zinc-alloy die castings undergo during aging. It is planned to report on this problem in a series of papers of which this is the first. The writers have made a study of commercial zinc die-casting alloys over a period of several years, utilizing the X-ray diffraction technic of determining the phase composition changes in the alloys. Up to the present, two principal phase changes have been observed which are capable of causing dimensional changes: (1) the segregation of secondary constituents from the zinc-base solid solution and (2) the beta aluminum-zinc decomposition. The latter is the subject of the present paper and studies on the former will be reported upon at a future time.

Jan 1, 1934

By Edmilson Renato de Castro

Apresentam-se o processo e o protótipo de forno para a produção de ferro gusa por redução carbotérmica estimulada por micro-ondas de minério de ferro, na forma de pelotas auto-redutoras. O forno de redução com potência regulável de até 15 kW de micro-ondas de 2.45 GHz foi especialmente projetado e construído para este processo. A estrutura do forno é em aço inoxidável e utiliza três geradores de micro-ondas focados para o centro de um aplicador cilíndrico. Com esta configuração conseguiu-se produzir um campo eletromagnético de alta densidade energética. A carga de pelotas auto-redutoras, com massa em torno de 20 g foi reduzida em um cadinho de carbeto de silício. A montagem do forno dispõe de uma balança elétrica adaptada para suportar o cadinho de redução. O presente forno dispõe de controle e medida da potência fornecida e refletida, permitindo medir a energia de micro-ondas efetivamente aplicada à carga. Esta característica permitiu realizar balanços de massa e de energia além de determinar a evolução da taxa de reação através da medida contínua da massa das pelotas sob redução, ao longo do tempo de processamento. Obtiveram-se curvas cinéticas de redução carbotérmica de minério de ferro incentivada por micro-ondas e de seu consumo de energia durante o processo.

Aug 1, 2018

By Pedro Jorge Walburga Keglevich de Buzin

A produção siderúrgica em usinas semi-integradas gera vários tipos de resíduos dentre os quais as carepas. No presente trabalho estuda-se o comportamento físicoquímico em altas temperaturas de briquetes autorredutores elaborados com carepa e finos de carvão vegetal produzidos no Rio Grande do Sul, objetivando sua introdução no processo produtivo de aciaria elétrica. Ensaios realizados em laboratório com briquetes industriais confeccionados com estes resíduos demonstraram a potencialidade de utilização destes briquetes autorredutores em processos siderúrgicos via forno elétrico a arco (FEA).

Aug 16, 2017

By David Leidel, Beth Shimer, James Stuart

Periodically, the Institute of Makers of Explosives Safety Library Publications are reviewed, edited and updated to reflect recent technical developments, new commercial explosive products and new regulatory requirements. The rapid proliferation of electronic devices, particularly portable communication systems, inventory management devices, navigational aids, etc., required the revision of the IME Safety Library Publication 20, “Safety Guide for the Prevention of Radio Frequency Radiation Hazards in the Use of Commercial Electric Detonators”. The new edition of SLP-20 has been updated to correct alterations to U.S. frequency allocations and maximum transmitted power permitted and a discussion of communications and tracking systems required in underground mining by the Miner Act. Also, an entire section was added dedicated to safe distances from RF sources to the special type of resistorized electric detonators used in the upstream oil and gas industry on wellsites and an enlarged section describing the particular types of RF sources that the blaster may encounter, perhaps in construction blasting operations.

Jan 1, 2012

By Rogério Pinto Coelho Catalão

No presente trabalho utilizou-se etanol no tratamento de cementação de engrenagens de aço DIN17NiCrMo5 utilizadas em transmissões automotivas. O processo de cementação foi realizado em fornos industriais contínuos utilizando gás natural e etanol como agentes cementantes às temperaturas de 870°C, 890°C e 930°C após o qual as peças foram temperadas e revenidas. As amostras tratadas foram submetidas à análise de fases por difração de raios-X e as microestruturas foram caracterizadas por microscopia ótica. O tamanho de grão austenítico das amostras tratadas foi determinado em 20 ± 2 µm com percentual de austenita retida entre 20% e 30%. A adição de etanol elevou o teor de CO na atmosfera do forno. Foi determinada a variação do teor de carbono em profundidade nas amostras tratadas, o que permitiu o cálculo das constantes de difusão do carbono na austenita.

Aug 8, 2018

By Warren J. Bruckard, Mark I. Pownceby, Sazzad Ahmad, M. Akbar Rhamdhani

Rutile is the preferred feedstock for producing high-grade TiO2 pigment but due to decreasing resources, alternative materials such as ilmenite is now used to produce a synthetic rutile (SR) feedstock. This requires removal of impurities (e.g. Fe, Mg, Mn) which, for a primary ilmenite is straightforward process. Processing of weathered ilmenite however, is complex, especially when chrome-bearing impurities are present since minor chromium downgrades the SR market value as it imparts color to the final TiO2 pigment, Chrome-bearing spinels are a problem in weathered ilmenites from the Murray Basin, Australia as their physical and chemical properties overlap with ilmenite making separation difficult. In this paper, different sulfidation process routes for weathered ilmenites are analyzed for their applicability to Murray Basin deposits as a mean of remove chrome spinel impurities. Thermodynamic and experimental studies indicated that selective sulfidation of chrome-bearing spinel can be achieved under controlled pO2 and pS2 processing conditions thereby making them amenable to separation.

Jan 1, 2015

CONTENTS PAGE Simons, Theodore.-Basic Principles of Gravity Concentration-A Mathematical Study : :.. 1 Taggart, Arthur F. and Gaudin, A. M.-Surface Tension and Adsorption Phenomena in Flotation 11 Hersam, Ernest A.-Factors Controlling the Capacity of Rock Crushers 12 Shaw, S. F.-The Ore Deposits of Sierra Mojada, Coahuila, Mexico 12 Wilson, Philip D.-The British Columbia Batholith and Related Ore Deposits 26 Greensfelder, N. S.-Shot-firing by Electricity 27 Mitke, Chas. A.-Metal Mine Ventilation in the Southwest 28 Foley, F. B. and Howell, S. P.-Neumann Bands as Evidence of Action of Explosives upon Metals 30 Schwartz, H. A., Payne, H. R., Gorton, A. F., and Austin, M. M.-Conditions of Stable Equilibrium in Iron-carbon Alloys 30

Jan 12, 1922

By Ellsworth Y. Dougherty, Edwards F. Fitzhugh

"INTRODUCTION During the summer of 1945 the Bureau of Mines made approximately 200 miles of reconnaissance magnetic surveys in north-central Mirnesota. The survey started near the western end of the Mesabi Iron Range and extended into the area to the southwest, west, and northwest and also southward to the-northern limits of the Cuyuna Iron Range. The purpose of the survey was to data to assist exploration for iron ore in the region through:1. Supplying a relatively unit form network of traverses, by which and future surveys of localities in the urea ray be correlated. Suggesting localities in which more detailed magnetic surveys may be justified, and, Disclosing localities in which there is lass hope of obtaining significant results from further magnetic surveys.The instrument used was a Hotchkiss Superdip, and traverses for calibration and comparison were run with a Schmidt-type magnetometer. Field observations and work directly related thereto were carried out under contract by E. J. Lang-year Co., Minneapolis. Engineers of the Bureau of Mines planned, directed, and reviewed the survey."

Aug 1, 1946

By Sergio Trindade

O elevado consumo de energia elétrica no processo de fabricação de ligas de manganês, associado a uma baixa disponibilidade deste recurso no Brasil, justifica a busca por processos mais eficientes que promovam o aumento da competitividade e sustentabilidade do negócio. O presente trabalho teve como objetivo quantificar o consumo de energia elétrica, na produção de ligas de manganês, em função da composição mineralógica da carga de alimentação no forno elétrico a arco. A metodologia adotada consistiu de quatro etapas básicas: revisão bibliográfica da caracterização mineralógica e química dos minérios de manganês utilizados no processo, levantamento do histórico de produção em função do consumo de energia e proporção de minérios na carga metálica de alimentação do reator, tratamento e discussão dos dados e, por último, elaboração do artigo. Os resultados permitiram identificar uma ordem a priorizar na alimentação dos minérios com melhores performance de processo. Os minérios são, na ordem do melhor para o pior, minério de manganês de Carajás (Azul), minério de manganês de Urucum e o minério de manganês Sílico Carbonatado (Morro da Mina).

Aug 17, 2017

By Howard Eavenson

THE low-volatile, or smokeless, coal field of southern West Virginia is in Fayette, Raleigh, Wyoming, Mercer, Summers and McDowell counties, in the extreme southern portion of the state, and extends into the adjacent counties of Tazewell and Buchanan in Virginia. McDowell County is the largest producer, with Fayette and Raleigh counties next. The total area of the field (Fig. 1) is approximately 1600 square miles, or 1,024,000 acres. The percentage of volatile matter in the various seams ranges from 15 to 26 per cent. The upper limit of true low-volatile coal is usually considered to be 23 per cent volatile matter; above this point, the coal usually is classed as medium volatile. This limit will be used in this paper.

Jan 1, 1931