Search Documents

By Modesto Bargallo

De acuerdo a las descripciones de los cronistas del siglo XVI, la "guaira" era un horno pequeño, portátil, de barro crudo y forma troncocónica o troncopiramidal cuadrada e invertida. En ese sentido, el presente texto señala las crónicas y relatos respecto del uso de dicho horno, así como las posibles localidades de las guairas al Cerro de Potosí y campos vecinos como Cerro de Porco y la región de los Lipes: las tres, en época colonial. Asimismo, Potosí y aledaños fueron el lugar clásico, donde funcionaron simultáneamente hasta unas siete mil guairas en sus mejores tiempos de fundición (antes de 1571) según Capoche, y en 6497 existían asientos de guairas.

Mar 1, 1969

By John E. Pahlman

The Bureau of Mines conducted column-leaching tests on 25 domestic Mn ores to determine the feasibility of extracting Mn by in situ or heap leaching with dissolved sulfur dioxide (S02) solutions. The ores tested were obtained from deposits in Arizona, Arkansas, California, Colorado. Maine, Minnesota, Nevada, and South Dakota. Dissolved S02 was found to be effective for leaching Mn; extractions greater than 90 pct were obtained with solution application rates of 1 mL/min from uncalcined, minus 2.5-plus 1.3-cm ore pieces. Leaching these ores with solutions containing only 5-wt-pct S02 and no added H2S04 resulted in Mn being selectively extracted over Fe except when Fe was present as goethite or siderite. Ca solubilization was inhibited by controlling the solution application rate (1 mL/min). The rate of leaching was found to be principally dependent upon the rate at which the leaching solution can penetrate the ore, since the solubilization of Mn upon contact with S02 was observed to be rapid. Despite low water permeabilities of the ores (as low as 10-2 to 10-4 darcy). greater than 90 pct of the Mn was extracted from even the largest ore pieces tested (approximately 10 cm in diameter). It appears, therefore. that leaching Mn opens up the pores, allowing penetration of the leach solution into the ore pieces.

Jan 1, 1988

By H. Yen, D. E. Walsh, H. K. Lin

"Comminution circuits are widely used in nonferrous and precious metals milling. Steel crushers, grinding mills and grinding media are typically used in comminution circuits. Comminution circuit wear products, in the form of metallic iron (steel) fines, are unavoidably produced and report to undersize products in the classification circuit, i.e., flotation or leach feed, while tramp grinding steel (TGS) reports to classification oversize products and returns to the grinding mill, building up in the circulating load. In laboratory studies, TGS reduced grinding efficiency significantly, the impact being dependent upon the size of the TGS present in the mill. Because iron fines adsorb flotation reagents effectively, iron fines increase reagent consumption and reduce flotation recovery. Iron fines are also capable of reducing gold recovery in cyanidation circuits via a cementation reaction. When using filtered gold solution from the cyanidation circuit of an Alaskan gold mine, the gold concentration in solution was reduced by 0.2 to 2.6% over various reaction periods when iron fines were present in the solution.IntroductionComminution circuits are widely used in copper, lead, zinc, nickel, cobalt, molybdenum and precious metal mills. Flotation and leaching processes are usually preceded by comminution (crushing and grinding) circuits in order to liberate valuable minerals for effective separation, concentration or dissolution by the subsequent flotation or leaching processes.Steel crushers, grinding mills and grinding media are typically used in comminution circuits. Comminution circuit wear products, in the form of metallic iron (steel) powder, are unavoidably produced and report to undersize products in the classification circuit (flotation or leach feed), while tramp grinding steel (TGS) reports to oversize productions during classification and returns to the grinding mill, building up in the circulating load. Variables affecting the amount of metallic iron powder and TGS produced in a comminution circuit include ore hardness, grinding mill operating conditions, comminution circuit design and the metallurgy of the steel used for manufacturing crusher liners, mill liners and grinding media. As one example, a comminution circuit product of 80% passing 200 mesh at the Pogo Mine, AK is estimated to contain approximately 2 kg/t of metallic iron. A finer grind will generally produce a comminution circuit product with higher metallic iron fines content."

Jan 1, 2015

By Bráulio Salumão de Oliveira

A participação do petróleo e gás natural na matriz energética mundial aumenta gradativamente a cada ano. Em estimativas para as próximas duas décadas, tais fontes continuarão a figurar entre as principais na participação em suprir a demanda por energia mundial. Para que seja tecnicamente e economicamente viável a exploração destes recursos, são necessários utilizar produtos e processos inovadores que, por sua vez, exigem evolução da pesquisa e desenvolvimento de novos materiais e processos. Este estudo objetivou analisar o desenvolvimento tecnológico de ligas ferrosas para os produtos tubulares utilizados nesse mercado, através da elaboração de indicadores a partir de documentos de patentes indexados na base Derwent Innovations Index entre 1995 e 2014. Foram elaborados indicadores de evolução temporal, de identificação dos elementos de liga, das tecnologias em processamento dos produtos e das propriedades requeridas além de comparativos entre principais desenvolvedores e seus mercados de interesse. O número de documentos de patentes sobre o tema aumentou significativamente durante o período estudado. Foram notados países com destaque no número de depósitos de patentes, porém com pouca expressão de pedidos fora de seu território. Os principais titulares são empresas japonesas embora a China tenha apresentado a maior tendência de crescimento de depósitos no tema.

Aug 16, 2017

By Robinson Reis Miranda

Este trabalho discute o desenvolvimento de massas de tamponamento de furos de corrida de fornos de redução: altos-fornos, fornos de ferros-ligas, cubilôs, entre outros, a partir de resíduos de chamote, materiais refratários, alumina e piche de alcatrão, subproduto da coqueria, utilizado como aglomerante. Foram investigadas as condições de plasticidade, resistência, usinabilidade, moldabilidade e poder de adesão. Os resultados obtidos mostram a possibilidade de emprego industrial destas massas de tamponamento.

Aug 7, 2018

By Daniel Alves Sodré

O processo de eletroerosão por penetração permite a usinagem de componentes metálicos nas mais variadas condições de tratamento termo mecânico e durezas. Entretanto, as tabelas e fórmulas tecnológicas empregadas para a execução deste processo não consideram essas distintas condições do material com uma variável. Desta forma, este trabalho objetivou avaliar a influência dimensional na usinagem via eletroerosão por penetração em componentes com e sem tratamento térmico de têmpera seguida de revenimento. Foram avaliadas amostras de aços ferramenta largamente empregados na indústria, representados pelas normas ABNT NM 122 Graus D6 e O1 e ABNT NM 87 Grau 1045. Observou-se uma variação dimensional de 20?m entre as amostras.

Aug 17, 2017

By Luis Noval Noval García

El objetivo de la ventilación es desarrollar una atmósfera saludable, segura y apta para la realización del trabajo por parte del personal. En ese sentido, el presente texto señala los gases como problemas comunes presentados dentro del ambiente minero tales como asfixia por anoxia (caso de inhalación) intoxicación, envenenamiento y muerte (letal) e inflamación y explosión (Productos). Para eliminar estos riesgos se debe eliminar las causas a través de una buena ventilación. Asimismo, es necesario conocer las propiedades de los gases, disponer de equipos para detectar su presencia y procurar los medios para eliminarlos.

Sep 1, 1984

By W. R. Crane

Subsidence and ground movement are phenomena common to and attendant upon practically all large-scale mining operations, and under certain conditions may occur in all workings, large and small. The interpretation of the cause of failure in rock masses involves a study of the nature of plants of weakness common to all rocks. The dominating planes of weakness can readily be determined by observation in any given locality, and in order of importance in the study of subsidence are (1) faulting planes, (2) bedding planes, (3) joint planes, and (4) other prominent planes of weakness such as thrust and shear planes and contacts. This report has mainly to do with the third item, joint planes, and is a preliminary statement which t to be followed by a more complete report in bulletin form.

Jan 1, 1931

By Joseph Hartshorne

EVER since the introduction of the Siemens regenerative furnace, it has been recognized that a certain amount of gas is lost each time the furnace-action is reversed. This loss comes, first, from the gas which passes through the free connection between the stack and the gas-main, which exists during the time the reversing-valve is turning over; and, secondly, from the gas which is in the chamber and flues, from the hearth to the reversing-valve, and which flows back into the stack when the valve is reversed. The amount lost each time is, of course, small; but, since a furnace is reversed from four to six times every hour for, say, 300 days in the year, the aggregate is large enough to be well worth attention. The estimate has been published' that, in Germany alone, the loss from the first of the above causes amounts to 500,000 marks per year. The loss from the second cause is, of course, much greater. A process for saving this entire loss, in use at Teplitz, Bohemia, for about three years, would seem to be of value even in this country, where coal is cheaper and where the small economies are not watched as closely as they are in Europe. This process, invented by Mr. Adelbert Kurzwernhart, late Technical Director of the Teplitzer Walzwerk, has been worked out with thoroughness. The loss from each cause can be calculated very closely for any particular furnace, and the results to be expected from the process ascertained. It can easily be decided, therefore, whether it is worthwhile to adopt it under any given conditions. The amount of chamber-gas lost depends upon,-(1), the cubic contents of the chamber, ports and flues upon one side of the furnace, up to the reversing-valve (deducting, of course,

Mar 1, 1906

By A. M. Gaudin

A new method of measuring the viscosity of unstable suspensions has been developed, using a Heinz viscometer. The technique was applied to kaolin-water suspensions. Spreads in viscosity with lime additive were measured.

Jan 1, 1962

By Robert D. Thomson

The plastics industry runs into the billions, both in the dollar value of its finished, products and in the pounds of plastic raw material produced. It is, too, one of the fastest growing industries with a 300 percent increase in production in the past ten years. Informed estimates set 5.9 billions pounds as the plastic volume for 1959. Statistically, this is equivalent to a per capita consumption of 25 pounds in the United States. Plastics are man-made materials in contrast to natural materials like wood and are a family of materials -- not a single material - each member having special advantages. A generally accepted definition; for plastics is; a large and varied group of materials which consist, wholly or in part, of combinations of carbon with oxygen, hydrogen, nitrogen, and other organic and inorganic elements. This, while solid in the finished state, at some stage in its manufacture is soft enough to be formed into various shapes, most usually through the application either singly or together of heat and pressure. Many combinations and many different materials are thus possible. Therefore, for purposes of simplification, most plastics can be classified under one of 14 recognized basic family groups. These groups in turn generally can be further classified into one of two major subdivisions - thermosetting or thermoplastics. A few plastics are in between and they can be formulated to be either thermosetting or thermoplastic.

Jan 1, 1960

By Ott F. Heizer

This paper describing the mining practices at the mines of Massachusetts, Massachusetts Co., Inc., at Mill City, Nev., is one of a series being prepared by the Bureau of Mines on mining practices, methods, and costs in tie various mining districts of the United States. The author acknowledges the assistance of William C. Vanderburg, associate mining engineer, U. S. Bureau of Mines, in the preparation of this paper.

Jan 1, 1930

By John C. Machisak

Injury data and experience, with related employment statistics, at coal mines in the United States for 1959 are presented in this publication under the following general sections: (A) General injury experience: Tables 1 to 6: Current data on number of injuries degree of injury, frequency and severity rates, average severity, and related employment and production data by work location. (B) Selected injury experience: Tables 7 to 38: Current data on principal agencies of injuries, distribution of injuries by part of body injured, days of disability, extent of hand and machine loading, experience by employment and production groups, and various other operating factors and physical conditions related to the occurrence of injuries at the Nation's coal mines.

Jan 1, 1961

By A. Vien, A. J. Neale, B. C. Flintoff, R. P. Edwards

Froth flotation is one of the most widely used and effective processes for mineral beneficiation. First introduced in 1911, flotation technology has seen many developments over the past 80+ years. Innovations in reagent chemistry, equipment design, process analysis and process control have given design and plant engineers a powerful set of "tools" for process optimization. However, it does not follow that all flotation systems are optimized. As Klimpel observes: "The problem with the industrial flotation process is that it is relatively easy to get reasonable results, and relatively difficult to get excellent results" Klimpel (I 988). While reasonable was sufficient in the past, competitive forces will make excellent necessary in the future. Judging by the activities in many Canadian plants this transition is already underway. This paper examines the role of some of the optimization "tools" in effecting this change.

Jan 1, 1994

By Fabiano Della Libera da Silva

Este artigo propõe uma metodologia para a construção de um Referencial Estatístico para a Utilização Física de equipamentos de mina. Para tanto, calcula-se um valor mensal (RE) apoiando-se em conceitos importantes para a operação de mina e que estão e inter-relacionados, como o comportamento sazonal da precipitação pluviométrica, o Teorema do Limite Central e a Gestão da Lacuna de Resultado. A metodologia proposta foi aplicada em uma mina de ferro a céu aberto e às frotas de transporte de um complexo minerador no Norte do Pará.

Aug 17, 2017

By Diogo de Oliveira Azevedo

No presente trabalho, processos de conformação a frio e recozimento foram aplicados à liga de magnésio ZK60A (Mg-6%Zn-1%Zr) com o objetivo de determinar a cinética dos fenômenos de recuperação e recristalização para permitir o refino de grão. Para tanto, foi desenvolvida uma série de matrizes de conformação para a trefilação incremental de barras circulares da liga ZK60A inicialmente recebida no estado envelhecido (T5), resultando em reduções de 7,8%, 15,4%, 22,6% e 29,4%. Após cada passe de trefilação, as propriedades mecânicas do material foram determinadas. O estudo do recozimento foi realizado em amostras com o máximo encruamento a temperaturas de 400°C, 350°C, 300°C, 250°C, 200°C e 150°C. Pela metodologia aplicada, foi possível avaliar a cinética do processo de recristalização da liga ZK60A e determinar a sua energia de ativação.

Aug 8, 2018

By J. H. E. Jeffes, K. T. Jacob

The activity coefficients of oxygen in liquid Pb-Sn alloys have been measured between 550 and 1100°C by use of solid oxide galvanic cells: Pt, Ni-NiO | Zr02 Solid electrolyte | O (Pb + Sn), Cermet, Pt; and Pt, Fe-FeO | Zr02 Solid electrolyte | 0(Pb + Sn), Cermet, Pt. Alcock and Richardson's quasi-chemical equation, with the coordination number of atoms set to 2, is found to predict successfully the activity coefficients of oxygen in these alloys. The relative partial molar enthalpy and entropy of oxygen at 1 atom per cent in the alloys have been calculated from the variation of the activity coefficient with temperature. The addition of Sn to an unsaturated solution of O in Pb is shown to decrease significantly both the partial molar enthalpy and entropy of O. As the measurements were restricted to a narrow range between 750 and 1100°C in Pb-rich alloys, however, the pronounced variation of the partial molar enthalpy of O with temperature at constant alloy composition predicted by the quasi-chemical model could not be verified.

Dec 1, 1971

By Paulo Santiago

Redução dos custos de operação e a produção de aço com menor impacto ambiental são diretrizes unânimes na siderurgia atual. A tecnologia das Turbinas de Recuperação de Topo (Top Recovery Turbines – TRT) é um aliado importante para seguir nessas direções. As TRTs produzem energia elétrica a partir do gás de alta pressão proveniente do topo dos Altos Fornos, gerando energia elétrica sem impacto em emissões. Durante a campanha de operação da turbina, a mesma pode perder eficiência operacional devido a, dentre outros, deposição sobre as palhetas. Com o intuito de melhorar o desempenho da turbina estabilizando sua geração durante toda sua campanha, foi desenvolvido um trabalho de dosagem de polímero dispersante na água de spray da turbina (para turbinas com tecnologia de água de spray na admissão do gás). A dosagem do polímero dispersante visa reduzir a deposição e incrustração nas palhetas, reduzindo assim a perda de performance durante a campanha causadas pelo incremento de massa nas palhetas. Os resultados alcançados em um teste de campo em uma siderúrgica no Brasil foram um incremento de 52% na geração durante a campanha onde o polímero dispersante foi aplicado. Com a aplicação do polímero, uma melhora significativa na confiabilidade e performance da turbina assim como a possibilidade da redução no consumo de água foram atingidos

Oct 30, 2017

By Jr. Raleigh

As part vi the development of the Coal Quality Expert (CQRN) --a computer program capable of predicting the impacts of coal quality on power plant performance, costs, and emissions control--several nationally important coals are being characterized to augment the coal quality database associated with the software. The project is sponsored by the U.S. Department of Energy and the Electric Power Research Institute (EPRI) under the Clean coal Technology Program. Since 1989, CQ Inc. (a subsidiary of EPRI) has characterized seven bituminous coals from Alabama, Illinois, Kentucky and Oklahoma and six sub-bituminous coals from the Powder River Basin (PRB) in Montana and Wyoming. Coals from the PRB region--being burned more frequently in Midwestern and southern power plants to reduce emissions of sulfur oxide compounds--can sometimes contain significant concentrations of potentially toxic elements. Although no limits were imposed on air toxics emissions from fossil-fuel fired utilities by the Clean Air Act Amendments of 1990, future regulations may be implemented at the conclusion of Federally-mandated emissions studies. One possible result is that any increased utilization of coals, including those from the PRB, may depend on the potential for removing toxic trace elements prior to combustion.

Jan 1, 1993

By MATT RENAUD, Mustafa Kumral

Mining corporations have spread their operations worldwide in the last few decades. The reason behind widening operations geographically can be seen as it being part of a risk diversification strategy. Given that the technical, financial and social risks are high, favorable deposits, taxation regimes and legislative frameworks create incentives for international mining operations. On the other hand, international mining activities add the risks of permitting, investing, operating and decommissioning to the corporations. These risks could emerge from defaulting, corruption, resource nationalism, social license to operate, and political and legislative uncertainties and instabilities.