Search Documents

By A. K. Andersen

One of the prime examples of the versatility of the MARCONAFLO system, which is a body of technology comprising the means to handle, store, load, transport, discharge and reclaim mineral commodities in slurry form, is the direct application of this process to leaching ores. The initial approach was to provide a much improved materials handling system for the transport of copper ores; however, an extensive development program, inclusive of prototype and pilot plant tests, has established that a new leaching concept is possible with this system. Data are presented from the leaching operation of a 25 TPD pilot plant utilizing a copper-oxide ore, mainly chrysocolla. This pilot plant was designed to incorporate true countercurrent flow where the ore is actually in motion, as contrary to vat leaching operations, and the ore being successfully leached is fine crushed ore (3/8-inch x o), contrary to agitation leach circuits. Extractions in excess of 85% of the soluble values are common with only 15 hours of retention time in the MARCONAFLO leaching system.

Jan 1, 1975

By John Henry Harden

This shaft, located in the northern anthracite coal-field about 2300 feet southwest from the court-house at Wilkes-Barre, in the County of Luzerne, Pa., is the property of the Lehigh & WilkesBarre Coal Company. The sinking and cribbing to the solid rock (see isometrical view on Plate IX) was conducted by Mr. W. W. Kenrick. Dimensions of the earthwork to the foundation of the cribbing, 51' 2" long, 17' 4" wide, 31' deep. Total amount of excavation in cubic yards, 998.5. Dimensions within the permanent cribbing, 45' 4" long, 11' 16" wide, 31' deep, divided into six parts by buttons 8" x 12", each division, 7' x 11' 6". Permanent cribbing 12" x 12"; temporary cribbing 8" x 10" ; backing, 3" thick ; clay puddle to exclude surface water, 12" thick; conductors, 8" x 5"; lining, 1" thick from top to bottom of the shaft. In the latter part of the year 1871, Mr. H. Murray & Son contracted with the company for the continuation of the work at the rate of four hundred dollars per yard in depth, to a point 100 feet below the Hillman seam of coal; for the succeeding 100 feet the price to be increased twenty-five dollars per yard, and so on until the bottom rock of the Baltimore seam of coal was found. The size of the shaft within the cribbing timbers is 45 feet 4 inches by 11 feet 6 inches, having six divisions of equal dimensions, 7 feet by 11 feet 6 inches, giving room for what is known as the "standard diamond " car, whose capacity when level full is 100 cubic feet, but when loaded by the miner 4 inches above the top contains 112 cubic feet." Two divisions of this shaft are intended for hoisting coal from the Hillman seam, two from the Baltimore seam, one for ventilation, and one for pumps. The works were planned for two pairs of direct-acting, high-pressure engines, twenty-four boilers, and for an estimated output of 2500 tons of coal per day from the two seams.

J. E. JOHNSON, JR., New York, N. Y. (communication to the Secretary*).-The discussion of Mr. Henrich's paper took place at a meeting from which I had the misfortune to be absent, and has just come to my attention. I do not wish to let the subject pass without contributing to it a little information which has come into my possession. In 1912, I published a brief note in the Transactions on The Effect of Alumina in Blast-Furnace Slags, giving in tabular form three typical slags used in iron blast-furnace practice, one of them the high alumina slag of, which Professor Richards speaks. That table is reproduced herewith. TABLE 1.-Composition of Slays. 1 3 3 4 5 6 7 CaO by Neutral Ratio Ratio Ratio Al2z03, SiO2, Differ- Substan- Cat Ca0 a A1203 Ratio Per Per ence, ces, CaO Cent. Cent. Per Per Al2O3 + Sioz Sit: SiO2 Cecil_ Cent. Virginia practice 6.5 36.0 54.0 3.5 1.27 1.6S 1.50 Lake-ore practice 13.5 33.0 50.0 3.5 1.08 1.92 1.51 Special experiment... 36.0 24.7 36.8 3.5 0.59 2.90 1.44 It supplies what seems to me convincing evidence that, for the purposes of the iron blast furnace, alumina can be regarded only as a neutral substance, dissolving in the slag and materially altering its viscosity, but not affecting its chemical activity. In subsequent experience with charcoal furnaces, I found the same rule to hold; that the chemical effect of alumina could be disregarded, providing the ratio of the lime and magnesia to the silica were kept constant. This is exactly the experience which Messrs. Dwight and Mathewson had in copper- and' lead-smelting furnaces. I have never seen any evidence or argument adequate to support the contention of Professor Richards-that the alumina acted as a base in the charcoal iron furnace and as an acid in the coke furnace, and that the function of alumina in iron-furnace slags is inherently different from that in copper- and lead-furnace slags-and I am compelled to differ absolutely with his conclusions in that respect.

Jan 9, 1917

By F. A. Rutledge

"The chromite deposits of Red Mountain, 10,miles southeast of Seldovia, Alaska, are in an intrusive of ultramafic rocks. The earliest reference to the deposits was made by U.S. Grant3/; J.B. Mertic, Jr. 4/ made a brief examination in 1917; and A.C. Gill5/ spent 7 weeks studying the ore bodies and geology of the region in 1918. The Federal Geological Survey had a field party in the region from July until September 1940 and the Red Mountain area was mapped and geological data were assembled by P.W. Guild.6/A preliminary investigation of the Kenai chromite deposits was made in July 1941 by R. S. Sanford,7/district engineer of the Bureau of Mines, accompanied by P. W. Guild, assistant geologist of the Geologi¬cal Survey. This was followed by surface sampling and core drilling, which were completed in September 1942 under the direction of John W. Cole,8 associate engineer of the Bureau of Mines. G. O. Gates, associate geologist, and A, B. Unkelsbay, junior geologist, of the Geological Survey, logged cores and interpreted geologic features revealed by Bureau of Mines drilling and trenching.9/J. C. Roehm, associate engineer of the Territorial Department of Mines; examined the Red Mountain area in august 1941.10/Additional exploration of other deposits in. the Red Mountain area was completed during the summer of 194. Work consisted of surface sampling, core drilling, and mapping. G. O. Gates, associate geologist of the Geological Survey, spent 4 days in August investigating results of the Bureau of Mines program.Throughout the exploratory work conducted by the Bureau of Mines the cooperation of Red Mountain Chromite, Inc., and especially of John Blodgett, Jr., and Collis 2, Druley, president and superintendent, respectively, was greatly appreciated. Use of their camp in the Windy River cirque and shops at Kasitsna Bay facilitated the Bureau of Mines program."

Apr 1, 1946

By B Mohanty, M Alam, F Gauthuer

A series of eleven full-scale production blasts has been earned out in a limestone quarry to study the effect of delay interval and its precision on overall blasting performance. The quarry employed ANFO and cartridged aluminized emulsion in 75 mm diameter boreholes with 2.6 m burden and 2.9 m spacing on a 6.7 m bench. Both V-cut and echelon designs were studied. The types of detonators tested were regular short period electric detonators with expanding delay intervals, a more precise pyrotechnic-based electric detonator (EXADET) with a fixed (25 ms) delay interval, and the ultra-high precision electronic delay detonator (EDD) with constant (but site-selectable) delay interval. The various techniques employed to assess the blast results are described, and the performance of the three types of detonators compared. The use of both EXADET and EDD lead to improved blast results in echelon design. Of the three delay intervals (25 ms, 38 ms, and 50 ms) studied, the best results were obtained with EDD with a 38 ms delay interval, which translates into a delay of 38 ms/m of effective burden. The results also show the need for modification of current V-cut delay designs to derive full benefits from these high precision detonators.

Jan 1, 1991

By J. Philip Neal

Feldspar is no example of special mineralization in isolated spots: it can usually be found within a mile or so of almost anywhere. Along with silica sand, it is a major part of our world's total mineral composition. This fact imparts to it an economic status different from a sulfide ore, or potash, or phosphate. While every feldspathic "stringer" does not possess economic potential, the generous distribution does yield a high statistical frequency of good feldspar ore bodies: the adjective "good" being subject to some flexibility of interpretation. The strong chemical bonds of this alkali aluminum silicate give it certain use advantages, but under present technology its individual elements cannot practically be separated to create aluminum, potassium, sodium, silicon - or their oxides. Its present uses rely upon chemical inertness - as in fillers; and on its physical melting characteristics and their effect in glass, enamel, or ceramics.

Jan 1, 1973

By W. D. Dietzman

In view of the developments and recent interest in recovering heavy oil, this report was prepared to present general information on more than 2,000 heavy oil reservoirs in more than 1,500 fields in 26 states. Information given on each heavy-oil deposit includes the following items: Field and formation, location, average or range of depth, average API gravity of oil, aver- age thickness of formation, areal extent of field, total productive wells drilled in field, discovery date of field, field status in 1963, cumulative production to Jan. 1, 1964, and all known types of secondary-recovery operations initiated (active and terminated) in the reservoirs. The geographical location of heavy oil accumulations in the United States is shown by a map, and a brief discussion of 14 different areas is given in the text. As of Jan. 1, 1964, 75 percent of the heavy oil reservoirs in the United States had produced more than 10 billion barrels of oil and are estimated to contain over 90 billion barrels of oil in place. It is also estimated that if the deposits which have had little or no production history, such as the one in Missouri, were included, the total remaining heavy oil in place would be in excess of 150 billion barrels. To find economical ways of recovering this vast reserve of heavy oil, industry is developing technology in several types of thermal-recovery methods. Some of the general considerations and more suitable limitations in selecting a prospect to study fur thermal-recovery techniques are: Lithology, depth, viscosity of reservoir fluids, gravity of oil, reservoir thickness, oil in place, and permeability and porosity.

Jan 1, 1965

By W. D. Dietzman

In view of the developments and recent interest in recovering heavy oil, this report was prepared to present general information on more than 2,000 heavy oil reservoirs in more than 1,500 fields in 26 states. Information given on each heavy-oil deposit includes the following items: Field and formation, location, average or range of depth, average API gravity of oil, aver- age thickness of formation, areal extent of field, total productive wells drilled in field, discovery date of field, field status in 1963, cumulative production to Jan. 1, 1964, and all known types of secondary-recovery operations initiated (active and terminated) Fn the reservoirs. The geographical location of heavy oil accumulations in the United States is shown by a map, and a brief discussion of 14 different areas is given in the text. As of Jan. 1, 1964, 75 percent of the heavy oil reservoirs in the United States had produced more than 10 billion barrels of oil and are estimated to contain over 90 billion barrels of oil in place. It is also estimated that if the deposits which have had little or no production history, such as the one in Missouri, were included, the total remaining heavy oil in place would be in excess of 150 billion barrels. To find economical ways of recovering this vast reserve of heavy oil, industry is developing technology in several types of thermal-recovery methods. Some of the general considerations and more suitable limitations in selecting a prospect to study fur thermal-recovery techniques are: Lithology, depth, viscosity of reservoir fluids, gravity of oil, reservoir thickness, oil in place, and permeability and porosity.

Jan 1, 1965

By M. A. Grossmann

THE hardenability of most steels can be predicted within 10 to 15 per cent provided the complete chemical composition is known, including "incidental" elements; and provided the as-quenched grain size is known; and provided, finally, that the composition and heating temperatures for hardening are such as to result in austenite free from carbide particles. In method proposed herein, the steel is considered as having a base hardenability due to its carbon content alone (the hardenability of a ''pure steel" of the given carbon content, without any other elements), and this base hardenability is multiplied by a multiplying factor for each chemical element present. After multiplying all these together, the final product is the hardenability. Grain sue may be taken into account either in the base hardenability or after the multiplication. Hardenability is stated in terms of "ideal critical diameter"; namely, the diameter of bar, in inches, that will just harden all the way through (absence of un- hardened core) in an "ideal" quench, and the calculation may also be related to the Jominy test. The data bring out certain features rather clearly. For example: I. It is quite useless to attempt to predict hardenability unless all elements, including "incidentals," are known; thus an "incidental" chromium content of 0.20 per cent increases the hardenability by about 50 per cent. 2. The relative effectiveness of different alloys is sometimes unexpected; thus molybde- num when calculated in this way appears to be of the same order of effectiveness as manganese, rather than much more powerful as wouldappear to be common experience; observe that an increase from no manganese to 0.20 per cent Mn provides a multiplying factor of 1.67, and an increase from no molybdenum to 0.20 per cent Mo provides a factor of 1.63, an increase of over 60 per cent in each case. However, if to a steel containing 0.50 per cent Mn there is added " 20 points of manganese," the factor is raised from 2.65 (for 0.50 per cent Mn) to 3.35 (for 0.70 per cent Mn), or an increase of only 26 per cent. Thus the first small addition of an element has a much more powerful percentage effect than an equal further addition when some is already present, and in most cases the effect of molybdenum is considered in relation to a steel in which molybdenum is absent. 3. If two elements are equally effective, a greater hardenability will be obtained by using, for example, 0.5 per cent of each than by using 1.0 per cent of either of them alone. 4. A knowledge of the as-quenched grain size is essential for precise work, since a difference of only one grain size number (say No. 7 instead of No. 6) makes a difference of almost lo per cent in hardenability (in these units); this, however, does not apply to certain steels of high hardenability. It should be emphasized that in chromium steels (over 0.30 per cent Cr) and chrome- molybdenum and chrome-vanadium steels, undissolved carbides are likely to be present in the steel as quenched, and that in such cases the charts can indicate only a maximum possible hardenability, whereas the extent of hardening actually obtained may be much less. Thus tests on a number of chrome-molybdenum steels have indicated a degree of hardening amounting to only 50 to 65 per cent of the maximum possible, and in chromium steels from full hardening (100 per cent) down to as low as 70 per cent. On the other hand, when the amount of such elements is small (Cr under 0.30 per cent, Mo up to 0.25 per cent in the absence of Cr, and V up to 0.04 per cent), the charts provide reasonable approximations. The precise figures on the charts are suggested as tentative, subject to some modification as more data accumulate, but the fundamental concept appears to be supported by tests made on a wide variety of steels, a few of the correlations being shown in Fig. I.

Jan 1, 1942

By Greisson Peixoto Rangel

A variação da resistência à compressão de argamassas geopoliméricas foi estudada em função da razão ativador/precursor e da molaridade da solução ativadora. As argamassas estudadas foram confeccionadas com metacaulim (precursor) ativado com solução composta por hidróxido de potássio e água destilada, e areia normal brasileira. De acordo com os resultados, a resistência aumenta com a diminuição da razão ativador/precursor e com o aumento da molaridade da solução ativadora. Além disso, os valores encontrados condizem com os presentes da literatura e com possíveis aplicações para argamassas de múltiplo uso.

Oct 30, 2017

By M. Carrales, C. J. Jirik, W. D. Dietzman

In view of the developments and recent interest in recovering heavy oil , this report was prepared to present general information on more than 2,000 heavy oil reservoirs in more than 1,500 fields in 26 states . Information given on each heavy - oil deposit includes the following items : Field and formation , location , average or range of depth , average API gravity of oil , average thickness of formation , areal extent of field , total productive wells drilled in field , discovery date of field , field status in 1963 , cumulative production to Jan. 1 , 1964 , and all known types of secondary - recovery operations initiated ( active and terminated ) in the reservoirs . The geographical location of heavy oil accumulations in the United States is shown by a map , and a brief discussion of 14 different areas is given in the text . As of Jan. 1 , 1964 , 75 percent of the heavy oil reservoirs in the United States had produced more than 10 billion barrels of oil and are estimated to contain over 90 billion barrels of oil in place . It is also estimated that if the deposits which have had little or no production history , such as the one in Missouri , were included , the total remaining heavy oil in place would be in excess of 150 billion barrels . To find economical ways of recovering this vast reserve of heavy oil , industry is developing technology in several types of thermal - recovery methods . Some of the general considerations and more suitable limitations in selecting a prospect to study for thermal - recovery techniques are : Lithology , depth , viscosity of reservoir fluids , gravity of oil , reservoir thickness , oil in place , and permeability and porosity .

Jan 1, 1965

By L Zhang

The Chinese coal industry is the largest coal producer in the world. The total production in I995 was 1.28 bnt. On the way towards introducing a market economic system, this mature industry is facing major challenges. The main problems are a large surplus of manpower, shortage of current assets and capital, low productivity, high casualties and a huge deficit. This paper discusses the present situation and the future developments in the Chinese coal industry. The current policy can be stated as ‘rapidly developing the state collieries and improving the village and private mines; integrated development to achieve an economic operating scale and encouraging a diversified economy; rapidly exploiting and developing in the North west and South west; promoting productivity and efficiency; welcoming multi-sources and types of investment; setting up coal exchange markets; and the careful control of resources and the environment'.

Jan 11, 1996

The low production rates associated with the underground metal mining industry have received considerable attention during the last decade. A number of significant technological advancements, in the form of new equipment, have taken place to improve the economics of ore production. Unfortunately, an extremely important factor in the equation -- the operator protection and safety -- continues to receive a low priority. The underground metal mining industry has one of the poorest industrial safety records in the United States. Equipment operators are constantly being placed in hazardous situations. Even one fatality is one too many. All of us bear the responsibility to eliminate it. This project is one of the important steps currently being undertaken by the U.S. Bureau of Mines to improve the operational safety of seven major pieces of ore handling equipment commonly used in underground metal and non-metal mines. The objectives of this study are; (a) to identify the existing hazards associated with the operation of the specific equipment, and (b) to recommend practical solutions that will minimize these hazards and reduce operator injuries. These recommendations are to be in the areas of equipment design improvements, additional operator protection and warning devices, equipment operating procedures and any modifications to the existing safety regulations.

Jan 1, 1975

By G. L. Mowrey

One critical element of the U.S. Bureau of Mines (Bureau) autonomous mining research program is the development of a reliable coal interface detection (CID) system. Several candidate CID concepts currently being investigated by the Bureau include vibration, passive infrared, radar, and natural gamma radiation (NGR). To establish which CID sensor technologies need to be developed for a given seam, coal and adjacent rock samples (i.e., immediate roof and floor) are being collected from selected major coal seams in the U.S. and are being analyzed in terms of NGR and other geophysical measurements. Results of the NGR measurements indicate that, in general, all shale and shale-like materials (e.g., drawslate, slate, and fireclay) have higher NGR readings than the coal seam. Consequently the NGR method appears to be a potentially useful CID tool, provided that the immediate roof and floor are both composed of a high percentage of shale-type material.

Jan 1, 1990

By R. J. Tocher

Uniaxial testing was performed on coal specimens to determine the time-dependent response. The testing was carried out on coal from six mine sites throughout the Western United States and Pennsylvania. Testing configurations were varied to allow analysis of moisture dependency, stress level and specimen orientation. Several theories were presented for the behavior of coal due to moisture diffusion. Experimental results showed the correlation between the theories and the actual material response. Coal deformation was found to be highly dependent on the moisture level of the testing environment. Moisture migration causes drying and shrinkage which lead to progressive degradation of the material. The coal tested experienced a rebound if saturated after a period of drying. This type of time-dependent behavior overshadows the dependence on the applied stress level, which, however, still produces a noticeable creep behavior. Analysis of one series of creep test results was performed. A relationship was developed on the basis of a simplified rheological model to describe the coal response to uniaxial stress. Previous empirical formulations in the form of power laws were compared and their deficiencies pointed out.

Jan 1, 1980

By Northcutt Ely

This volume summarizes mining and petroleum legislation in 45 African jurisdictions. Within these jurisdictions, primary attention is given to requirements that must be met in each country for acquisition of rights to permit development of mineral resources. Coverage includes: First, identification of the controlling laws or statutes governing minerals acquisition and reference to the administrative authority; second, analysis of the laws governing mines and quarries and their products; third, analysis of laws applicable to natural gas, petroleum, and related materials; and fourth, mention of laws regulating offshore operations. Where pertinent, sections dealing with historical background or administration have been added. In countries where minerals are subject to control of states or provinces, those areas are considered separately from the central government.

Jan 1, 1974

By R. D. Auten

This paper is primarily a report on the process of using oolitic aragonite, as received from Marconi& Ocean Industries, Ltd. without further processing, for a major portion of the raw feed to a rotary kiln producing cement clinker. Oolitic aragonite is a high purity calcium carbonate material, dust free, with the appearance of a course, white sand. It is farmed when under the right conditions of temperature ocean currents, and ocean floor topography. The calcium carbonate will precipitate into small spherical particles on the ocean floor. These oceanic conditions are correct to cause precipitation of the calcium carbonate near Ocean Cay in the Bahama Island chain. The present growing deposit near Ocean Cay is in the billions of tons and is mined by a relatively shallow-operation hydraulic dredge. The aragonite thus formed is en orthorhombic crystaline form of calcium carbonate with a specific gravity of approximately 2.9. At a temperature of 505°C. (940F), the aragonite converts to the hexagonal crystal of calcite with a specific gravity of 2.6 to 2.7. This change in specific gravity weakens the structure of the particles but the individual pieces are still fairly hard. When the material is then calcined at 900°C (1650°F), the particles retain their shape but become soft and will break up under finger pressure.

Jan 1, 1978

By Derek J. Fray

"In order to extend the application of fused salts in\the electrowinning and electrorefining of metals, it is necessary to maximise the current density, minimise the voltage drop and greatly increase the area of electrode surface so as to compete with the space-time yield of pyrometallurgical reactions. The various designs of electrowinning cell are reviewed and it is shown that by the application of a modest centrifugal field it is possible to reduce the anode to cathode interelectrode spacing to 4 mm whilst still maintaining a current efficiency of 85-90%.The thermodynamic potential for electrorefining is far less than for electrowinning yet fused salt electrorefining is only applied in limited cases. The reasons for this are discussed and the important design parameters evaluated. It is concluded that by using packed bed electrodes, separated by a diaphragm, the possibility of electrorefining with very low energy consumption can be achieved. Carbothermically-produced metals are always cheaper than those produced by electrolysis but suffer from the disadvantage of low purity. It is proposed that fused salt electrorefining may offer an energy efficient way of upgrading the metal. IntroductionThe majority of metals can be deposited from fused salts (1,2) but as commercial production is restricted to the more reactive elements, it is worthwhile considering the advantages and disadvantages of fused salt electrolysis as' compared to smelting and aqueous electrolysis. The advantages over aqueous extraction are as follows:1) the much higher conductivities and diffusivities result in much lower IR losses and higher current densities can be achieved at modest voltages;2) the elevated temperatures of operation result in larger exchange currents which give rapid kinetics and lower activation polarisation for the electrode reactions;3) the absence of water as a solvent means that it is not necessary to consider the evolution of hydrogen as a competing cathodic reaction. Furthermore, alkali halide salts, often used as solvents in fused salt electrolytes, have high deposition potentials;4) molten salts generally are mutually soluble and, therefore, concentration polarisation effects are minimised."

Jan 1, 1988

By R. C. FLEMING

G OLD MINING is enjoying a real revival in the West, and a considerable portion of the production is coming from small properties. The large mining companies of the world get most of the publicity, but in the last year the small gold property has often proved a more attractive field for the mining engineer looking for something to do. Old mines have been re- opened, prospects have been more closely examined, and many properties that were out of the running with the high commodity and labor costs of two or three years ago, have recently been making money for their operators. An interesting phase of this activity is the operation of so-called one-man mines. The west is dotted with these small properties, without the resources or reserves to warrant large-scale operation, but which return a living and often something over to one or two men who under- stand mining and simple methods of treatment.

Jan 1, 1932

By A. Sainato, S. J. Schatzel, D. M. Hyman, J. C. LaScola

The Bureau of Mines determined the gas contents of 135 oil shale samples obtained from approximately 630 ft of core drilling. Drilling was done within a projected mining zone of the Cathedral Sluffs Mine, located in the Piceance Basin of western Colorado. Methane contents were determined by the modified direct method, which can measure the volumes of several gases released from or reacted with mine rock without destructive sample treatment. Over the duration of the test, nitrogen was largely unreactive, CO2 increased slightly, oxygen decreased markedly, and methane increased more than the total increase of all contained gases. The gas volumes were normalized per unit sample mass and are given in cubic centimeters per gram. Common time irzdices for test duration of 3, 40, and 125 days were used to compare methane desorption among samples. The means of the sample populations for these indices were 0.0316, 0.114, and 0.195 cm3/g, respectively. These quantities are lower than those reported in a Bureau emissions study at the Horse Draw Mine in the Piceance Basin. Oil shale samples that were gas enriched beyond the mean methane contents frequently contained bitumens and pyrite.

Jan 1, 1987