Search Documents

Mineralogical analysis of a nickeliferous laterite from the Rockhampton region shows that the nickel is largely associated with the manganese wad and opaline silica. The laterite also contains an appreciable chromite content (about 12 per cent Cr2O,) although this tends to be poorly liberated.Leaching with hydrochloric or sulphuric acid, at atmospheric pressure at the boiling point is non-selective with respect to iron dissolution.The degree of dissolution increases as the acid concentration and retention time are increased; cobalt dissolution requires less aggressive conditions than does the dissolution of an equivalent amount of nickel.Leaching with sulphuric acid at elevated temperatures and pressures leads to a minimum amount of iron dissolution, is rapid, and requires a reduced acid addition rate. Nickel and cobalt recovery from the clarified leachate would be simplified because of the leach selectivity.Pressure leaching appears to be the most practical route for treating the Rockhampton laterite. The economics of processing would be made more attractive by the recovery of a chromium concentrate from the leach residue. This would typically contain about 45 per cent Cr2O, and could be used as a source of chromium chemicals.

Jan 1, 1986

A model was developed to facilitate secondary tailgate support selection based on analysis of over 100 case studies, compiled from two different surveys of operating longwall coal mines in the United States. The ALPS (Analysis of Longwall Pillar Stability) program was used to determine adequacy of pillar design for the successful longwall case histories. A relationship was developed between the secondary support density necessary to maintain a stable tailgate entry during mining and the CMRR (Coal Mine Roof Rating). This relationship defines the lower bound of secondary support density currently used in longwall mines. The model used only successful tailgate case history data, with adequate ALPS SF according to the CMRR for each case. This model facilitates mine design by predicting secondary support density required for a tailgate entry depending on the ALPS SF and CMRR, which can result in significant economic benefits.

Jan 1, 1996

By J. P. Sancho, J. M. Duart, J. I. Verdeja, J. O. García

Following a short review of the history of rails used in the transport of passengers and goods, this paper describes the process for rail fabrication, rail structure, and properties, and summarizes the fatigue test curves carried out on rails used today. Also reported is the process for “continuous rail” production using aluminothermic welding via the introduction of weld metal in onsite casting, as a homogeneous melt. Weld characteristics of aluminothermic welding using different preheating procedures—fusion zone, heat-affected zone, microstructure, hardness, slow bend test, and fatigue test resistance (Wöhler curves)—are related to preheating and welding procedures of 700, 900, and 1,100 MPA rail grades. The Locati method is preferred over the staircase method for ascertaining the fatigue limit due to its simplicity. Macrographic and metallographic inspection of broken specimens reveals the reliability of welding techniques and the good metallurgical quality of welds.

Jan 1, 2007

By Gibbs R

The objective of this paper is to provide a broad qualitative perspective of the needs and costs of infrastructure associated with typical mining projects. Infrastructure may be defined as anything necessary for the development and operation of a project, which is peripheral to the basic extraction, handling and processing of material. As depicted in Figure 1, infrastructure acts as the link between the technological heart of a project and the outside world.

Jan 1, 1990

By Parker JB

The Channar Iron Ore Mining Project (the Project) is a joint venture involving the Hamersley Holdings group (Hamersley) and the China Metallurgical Import and Export Corporation (CMIEC). The Project represents the first new iron ore mine development in Australia since 1971/72 and is the first major overseas mining investment by the People's Republic of China (PRC). The Channar mine is being constructed in the Pilbara region of Western Australia and will operate for more than 20 years supplying the PRC with 200 M tonne of high grade iron ore. The Project is configured to take advantage of Hamersley's existing production and support facilities. The Joint Venturers will invest A$280 million to achieve an initial production rate of 3 M tonne/yr and an additional A$120 million over the next 8 years to achieve full capacity of 10 M tonne/yr. Financing the Project to meet the requirements of both Hamersley and CMIEC, with the dependance of the Project on Hamersley's infrastructure, and in a depressed iron ore market, required an innovative financial structure to be arranged in a limited period. This paper describes both the financial structure and its implementation, and draws a number of conclusions regarding the financing of resource projects.

Jan 1, 1989

By L. C. Stone, J. C. Parr, T. N. Anderson, D. Metcalf

An increase in the importance of low-grade materials as sources of gold and silver has led to the need for improved analytical methods on leach solutions, ores and various effluents, residues, and in-process streams. These are required by plant operators as guides to process control and for accounting pldrposes. Atomic absorption spectrophotometry (AAS) and AAS preceded by pre- concentration have been applied successfully to resolve many such problems. However, AAS is no panacea and imprecision or loss of accuracy can result if adequate precautions are not taken to prevent losses and eliminate interferences. The recent methods are discussed together with methods for overcoming difficulties. Comparisons with more classical analytical techniques are also given.

Jan 1, 1981

By Karl R. Becker

A variety of commercial detonators (fuse type and electric instantaneous and delay types) were subjected to impact and thermal stimuli to determine initiation stimulus levels and the dominant parameters in resistance to initiation. In the impact trials the detonators were impacted along their length to find the most sensitive region; threshold initiation limits obtained for these regions ranged from 3.47 to 20.82 joules (2.6 to 15.4 ft-lb). The friction sensitivity of the explosive component was an important parameter in determining sensitivity; various construction features of nonexplosive components played a role as well. In the thermal sensitivity trials, the detonators were heated from ambient to 100° C at an average rate of about 1.0° C/min, and thereafter at 0.5° C/min until they exploded; the explosion temperatures observed ranged from 121° to 188° C. These temperatures correlated quite well with the reaction temperatures of certain characteristic explosive components used by different manufacturers. The data also indicated an effect of confinement on explosion temperatures of detonators.

Jan 1, 1975

Sulphuric acid leaching at atmospheric pressure of a number of Australian nickeliferous laterites was examined in detail. The results obtained indicate that nickel can be extracted from these ores, although the conditions required to achieve about 90 per cent extraction vary widely. These differences in reactivity can be related to the types of nickel-bearing minerals present.Nickel is more readily extracted from nickel-bearing clays such as chlorite, than it is from nickel-containing goethite.The results clearly show the problems associated with the processing of complex ores such as the nickeliferous laterites, and they indicate the need for complete characterization of each deposit.

Jan 1, 1978

By Y. Oka, H. Majima

When a rock particle is subjected to an external force, internal stresses and deformations are experienced by the particle. Assuming that the breakage of a rock is mainly due to tensile stresses generated by the action of a pair of concentrated loads, F, directed in compression towards the loading points at the shortest distance, as illustrated in Fig. 1, the stress and deformation experienced by a particle of irregular shape can be determined with the aid of the theory of elasticity. According to the photoelastic experiments made by one of the present authors,' the stress states in a rock particle of irregular shape are quite similar to that of an inscribed sphere of diameter x, as indicated in Fig. 1, but accompanied by the faint stresses, in the vicinity of the particle outside of the inscribed sphere. Therefore, the stress components in an irregularly shaped particle can be estimated by referring to stress components in a sphere. Applying polar spherical coordinates to an elastic spherical body, as shown in Fig. 1, the stress components are all expressed as multiples of F /x2 and more or less influenced by the loading angle and Poisson's number m. In general, the energy w, acting on a rock particle is defined as the product of loading compression F

Jan 1, 1970

By Raymond B. Ladoo

Talc is a hydrous magnesium silicate having the chemical formula H2Mg3 (SiO8 ) 4 ; it is often called steatite, soapstone or potstorie, and by the trade names talc clay, agalite, asbestine, and verdolite. The term talc may be used to include all forms of the pure mineral, whereas steatite denotes particularly the massive, compact variety, and soapstone the impure, massive form that often contains only 50 per cent of talc. Merrill 1 says: The name soapstone is given to dark-gray and greenish talcose rocks, which are soft enough to be readily cut with a knife, and which have a pronounced soapy or greasy feeling; hence the name. Such rocks are commonly stated in textbooks to be compact forms .of steatite, or talc, but as the writer has elsewhere pointed out, and as shown by the analyses here given, few of them are even approximately pure forms of this mineral, but all contain varying proportions of chlorite, mica, and tremolite, together with perhaps unaltered residuals of pyroxene, granules of iron ore, iron pyrites, quartz, and, in seams and veins, calcite and magnesian carbonates. When pure, talc is soft, having a hardness of 1, but when impure or when it grades into its varieties, the hardness increases to 3 or 4. Talc ranges in color from pure white and silvery white through gray, green, apple green, gray green to dark green, nlso yellow, brown, or reddish when impure. It is rarely, if ever, found in wellformed crystals, but often occurs in foliated plates or in fibrous aggregates. It is commonly compact or massive or in fine granular aggregates. Several analyses of talc from different regions ·are given in Table 1. Talc has several varieties, the most important of which is Rensselaerite. This variety, found in a small area near Gouverneur, St. La.wrence County, N. Y., is a hard, fibrous, -waxlike mineral having the same chemical composition as talc, but lacking its softness and its peculiar greasy feel. Its hardness and its peculiar fibrous form, even when ground, have made its grinding and separation a separate problem. In addition to the varieties of talc and soapstone, the mineral pyrophyllite or agalmatolite, a hydrous silicate of alumina, with the formula H2Al2 (Si08 ), is also mined and sold as talc. It resembles talc in color, feel, luster, and structure, and may be successfully substituted for true talc for most uses. In this paper it will be considered as one of the commercial forms of talc.

Jan 1, 1923

By Edward E. Johnson

The U.S. economy made significant progress in 1984. The current-dollar gross national product (GNP), the market value of the Nation's output of goods and services, increased almost 11 percent over that of 1983 to slightly more than $3.66 trillion (table 1), and the real gross national product increased almost 7 percent.2/ Such rapid growth in real GNP has not occurred since the early 1950's. Real final sales increased only 5 percent during 1984, and real business inventories increased $24.8 billion ($57.9 billion in current dollars). Total employment of 106.7 million was an all-time record, and the unemployment rate declined from 9.5 percent in 1983 to 7.4 percent in 1984. During 1984 the U.S. dollar showed great strength on international markets, contributing to large current-dollar negative net exports of goods and services (-$62.5 billion) and even larger negative net exports of merchandise (-$107.6 billion). The strong dollar and the substantial increase in net imports of goods and services helped reduce U.S. inflationary pressures and provided a major source of loanable funds for financing domestic private investment.

Jan 1, 1985

By Robert M. Semple, Harvey W. Parker

INTRODUCTION Two promising innovative tunnel support systems are being developed by the Civil Engineering Department of the University of Illinois. One of these is a lining which can be placed by a slipform located immediately behind and contiguous with a tunneling machine. Recent advancements in construction materials appear to provide the breakthrough required to make such a system feasible and practical. The lining material which permits this construction scheme is wire fiber reinforced concrete made with high, very early strength regulated-set cement. Parts I and II of this paper relate to this slipformed liner. Part I discusses the material and equipment required to install the liner. The "Extruded Liner System" (ELS) has been devised to place the lining. This ELS concept is briefly described and a tentative development program is outlined. In Part II, the physical properties and practical construction aspects of the liner material are discussed and a program for structural testing of 10-ft diameter prototype tunnel supports is presented. Part III contains descriptions of improvements to conventional steel-rib tunnel supports. It is shown that square tubular box sections are structurally superior to wide flange sections for complex loading conditions often encountered in rock tunnels. Analytical studies and tests on connections have been performed to evaluate their structural behavior. These are presented along with a program for comparative large-scale tests on horseshoe-shaped frames with a 10-foot span. This research is being conducted by the Department of Civil

Jan 1, 1997

By Met B. E

During the operation of the Parkes process of desilverising, and in the earlier days of the continuous process, gold and silver were removed separately from softened lead bullion. Gold was removed in the Parkes process by a selective zincing, and -in the continuous process by treatment with zinc in a special de-golding kettle, in each case a crust being obtained carrying the gold and a small portion of the silver. Actually the process could have been more correctly termed a de-copperising process, on accountof the relatively large amount of this metal present, and its affinity for zinc, which caused it to enter the crusts produced.The crust was treated in reverberatory furnaces, where the bulk of the copper and zinc was removed in by-products, and the resulting "gold bullion" cupelled to give adore bullion containing approximately 2,000 ounces gold per ton.For the purpose of parting this dore, a small Balbach-Thum plant of 11 cells was used, and once each six months a short campaign was conducted on the accumulated metal.With the development of the process of de-copperising smelter bullion by means of sulphur, when a bullion averaging about .004% copper was constantly available for refining, the need for a separate de-golding process disappeared.The de-golding kettle of the Continuous Process...

Jan 1, 1937

By E. S. Chalpin

On 25 August 1971, the U.S. Bureau of Mines contracted with the Aerojet Liquid Rocket Company to perform an engineering research program to be completed on 25 May 1972. The program objective was to evaluate the advantages and disadvantages of the underground use of several power sources including but not limited to a closed cycle diesel, electric cable/motor, rechargeable battery/ motor and exhausting diesel for mine shuttle cars, with emphasis on health and safety. This report, Research in Advanced Power Systems for Mining Health and Safety consists of four (4) main parts: (1) Hazards and Safety Analysis of Mine Power Systems, (2) Evaluation of Closed Cycle Diesel Power System for Mine Applications, (3) Closed Cycle Diesel Power System Consumables Compatibility, and (4) Concluding Remarks and Recommendations. The hazards introduced to a mine by shuttle car power system failure modes were evaluated and reported. A "fault tree" analysis was generated for each power system and the probability of death or injury during an eight (8) hour shift and for a week of operation (105 hours) were estimated. Advantages and disadvantages were also reported for each system studied. Aerojet's assessment, based on a "forced decisions analysis," of the four shuttle car power systems as to their relative health and safety is that the exhausting or open cycle diesel is preferred, followed by the closed cycle diesel, the electric cable/motor and the rechargeable battery/motor. The assessment was based on ten parameters pertinent to the health and safety aspects of shuttle cars. Drawing layouts of two typical mine shuttle cars incorporating closed cycle diesel powerplant concepts are included in this report. The performance parameters established for the two concepts are tabulated. A study was made of the logistics involved in transporting and replenishing the consumables needed to operate a shuttle car equipped with a closed cycle diesel. The closed cycle diesel powerplant consumables -oxygen, potassium hydroxide, and diesel fuel - were analyzed as to their compatibility with materials found normally in a gassy coal mine. Spill tests simulating inadvertent leakage of liquid oxygen in a coal mine were performed. A critical evaluation of existing oxygen sensitivity data and the relationship to the use of oxygen on a shuttle car in a coal mine environment is presented.

Jan 1, 1972

By J. C. Potvin

Although the occurrence of deposits of titanium minerals on Kenya’s present day beaches and adjacent dune systems has been well documented, the potential for older formations to host economically viable deposits had not been recognised until recently. The Magarini sands formation in Kenya has been found to contain deposits of ilmenite, rutile and zircon in quantities and grades that have the potential to be commercially exploited. Since 1995, Tiomin Resources Inc. has explored these deposits and has identified one deposit, the Kwale project, as being able to support the development of a mine producing some 300,000 tpa ilmenite, 75,000 tpa rutile and 37,000 tpa zircon. Tiomin plans to start production by late 2002. Construction of a US$137 million operation is set to commence in the first half of 2001.

Jan 1, 2001

By T A. J Hopper, B J. Birt, K K. Trofimczyk

Nuclear magnetic resonance (NMR) has been utilised in the oil and gas industry for over 60 years. The technology was recently identified as having potential value in iron ore, where latent bound moisture may affect ore handling even after dewatering and extraction. The first step in introducing this technology to iron ore involved laboratory tests on drill core samples. These results established the parameters for a downhole borehole magnetic resonance (BMR) tool for iron-rich environments, which was subsequently developed. A major challenge involved shrinking what is a very large tool in the oil industry to a slimhole, lightweight, 1-man deployable mining tool.Of primary concern was the ability to measure the very fast transverse relaxation times (T2s) seen in the lab results on iron ore samples. Iron creates local field gradients that significantly decrease the T2 times. As a result, the BMR tool had to be able to measure T2s in the range of hundreds of microseconds, a level not required in clastic sedimentary formations. The choice of T2 cut-offs in iron ore is critical to successfully separating the free and bound fluids. The industry has typically focused on T2 cut-offs in clastics and carbonates, but not in systems with high iron content. Using core analysis results (poro-perm and NMR) we were able to verify the BMR response. The T2 cut-offs were determined from NMR core analysis and then applied to the logs so as to provide a continuous, calibrated permeability log.Field results that highlight the challenge involved in logging in iron-rich environments are presented, as well as some minimum requirements for a successful BMR log. Examples from boreholes in an active iron ore mine in the Pilbara iron ore province in Western Australia are presented, as well as explanations for how NMR data can be combined with bulk density logs to provide a continuous dry weight density log based on the original density-porosity equation from Alger et al (1963).CITATION:Hopper, T A J, Trofimczyk, K K and Birt, B J, 2017. Development of a slimhole downhole nuclear magnetic resonance tool for iron ore – some applications and limitations, in Proceedings Iron Ore 2017, pp 473–480 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

By Honeycombe R. W K, Greenwood J. N

Powder metallurgy has been developed rapidly in the last twenty years by overseas metallurgists. The technique of making the powders and their subsequent pressing and sintering into useful forms has' only been introduced into Australia under the stress of war-time economic conditions.The technique involved has very little in common with our usual methods of fabricating engineering alloys by melting the ingredients to a homogeneous mass, followed by casting to shape or casting to ingot form and shaping by application of pressure-so-called mechanical working. On the other hand, the technique includes operations, such as milling and sizing, familiar to the primary metallurgists.The compacting of metal or other powders finds important application in two outstanding fields of engineering production: (a) in making porous bearings and contact brushes, in which such a material as powdered graphite can be incorporated; (b) in making cutting tool tips of hard -carbides, which have a melting point too high to make casting feasible, and which would be too brittle in the cast condition in any case. In both these cases; the final article can be made of the desired shape and size (subject to shrinkage allowances) whilst the compact is in a soft and readily machined condition a consideration of great importance in connection with the hard carbides.In order to develop the necessary equipment and technique and at the same time to assisil in the war effort, it was decided to divert the research work of the Metallurgy Department of the University of Melbourne to the problems associated with the production of hard carbides from local raw materials and the sintering of such into tips for cutting tools. Since this work was started at least two industrial concerns have started to produce these materials in the Commonwealth.The work. to date has included (a) the purification of crude cobalt oxide from Risdon and the reduction of this to metal Particles of less than 10 p. diameter; (b) the production of tungsten powder from King Island scheelite and its conversion into tungsten carbide with particle size less than 4 p. diameter; (c) the sintering of the latter product, using the former as a bond; (d) the production of titanium carbide from titanium dioxide; (e) the separation of columbium and tantalum oxides from a Northern Territory tantalite, and the conversion of these into the respective carbides.

Jan 1, 1942

By Jasper L. Stuckey

PYROPHYLLITE, first identified as soapstone,' later as agalmatolite,2 and finally as pyrophyl-lite, has been known to occur in North Carolina for more than 130 years and has been produced intermittently in commercial amounts for the past 100 years. Pyrophyllite mining, however, has become a major industry in North Carolina only during the past 25 years. North Carolina and California are the chief producing states. Current annual production averages 125,000 tons, of which slightly more than 90 pct comes from North Carolina. Distribution and Geologic Setting: All known pyrophyllite deposits in North Carolina are associated with rocks of the Carolina Slate Belt,' which is composed of a vast series of metamorphosed volcanic and sedimentary materials, occurring as two zones extending in a northeast-southwest direction across the state. The larger of these zones, lying in the central Piedmont region, varies from 8 to 50 miles wide. The smaller zone lies along the eastern edge of the Piedmont region and is partly covered by coastal plain sediments. The rocks in both zones consist of a great volcanic-sedimentary series, composed of air-laid and water-laid tuffs and breccias, lava flows, and slates. On the basis of composition, they may be classed into three groups: 1) tuffs, breccias, and lava flows of acid or rhyolitic composition; 2) tuffs, breccias, and lava flows of a basic or andesitic composition; and 3) water-laid slates composed of fine grained materials derived chiefly from the acid tuffs and breccias and

Jan 1, 1959

By J. B. Forrester

In the operation of the coal mines in Utah few adverse conditions confront us. Physical conditions for the economical extraction of the coal are as near perfect as it is possible for them to be. Still several obstacles are encountered to keep up our interest and prevent us from getting in a rut. Of these I shall speak only of Burning, Wants, and Sluffing of Ribs. Should one travel the outcrop from Ivy Creek in Emery county to the Utah-Colorado line, there would be one outstanding feature indelible impressed upon one's mind. That feature is the omnipresent indications of burning in place. Viewing the eastern escarpment of the Wasatch Plateau from a distance, many splotches of dark red are plainly seen always lying above the coal floor. This stratum is a felspathic sandstone, appearing as a white line running the full length of the above escarpment and about midway between the floor of the valley and the top of the plateau. The coal bearing complex consists of shales, sandstones and coal. This complex varies from two hundred to eleven hundred feet in thickness. The number of coal seams are exceedingly variable. As a rule the argilutites form the bulk of this complex. This material is baked by the burning of the coal and the iron present is oxidized to the ferric state, coloring the shale to a dark red. This baked material forms a shingle tales that in places cover the entire complex. It is natural to expect that the most extensive burning is in the canyons facing to the south and east and on the south slopes of the ridges running to the east or west. Such, indeed, is the case. Still in this arid region many crop fires have existed upon the north slopes, especially in those canyons that face to the east. In fact today, instances are not rare where grassy north slopes, heavily timbered with balsam and fir that have attained a diameter of 14 to 24 inches, are found growing upon the disintegrated baked shingle and later development proves that the coal has been burned at least 500 feet back from the outcrop. Still these conditions are not normal. In this arid climate the south and east exposures are steep and barren, except for the scrub pine, cedar, mahogany and kindred semixerophytes. Bunch grass is also a lover of such exposures. There is very little soil found in such places; it is either blown away as fast as formed or washed away by the rare torrential rains, or the rapidly melting snow. Thus we see that the physical conditions are favorable for the starting and maintainence of outcrop fires. This brings us to the probable origin of this phenomenon. There are four probable ways' that such fires, could be started, namely:

Jan 1, 1921

By James A. Schneider

The successful installation of long piles driven into very dense sands relies on the occurrence of the reduction in local friction with increased pile embedment, a phenomenon known as ?friction fatigue?. The underlying mechanisms controlling friction fatigue are poorly understood, with some design methods including an adjustment for the influence of pile diameter while others do not. This paper back calculates the installation resistance of 0.356m to 2m (14in to 78in) diameter open ended piles driven into very dense sands using wave equation analyses. Cone penetration test data are used to link soil properties to installation resistance. The study illustrates consistent interpretation of a variety of case histories of open ended piles driven in very dense sands using newly developed analysis techniques and normalized parameters. Results provide information on methods for incorporating friction fatigue into drivability studies as well as a discussion of mechanisms related to pipe pile installation resistance in sandy soils.

Jan 1, 2010