Search Documents

By D. Gearhart

Full-scale tests are conducted on mine roof supports using protocols developed by the National Institute for Occupational Safety and Health (NIOSH) using the unique capabilities of the Mine Roof Simulator (MRS). These protocols simulate the loading conditions that the support will be exposed to in an underground mine to determine the performance capabilities and limitations of the support. Some tests are conducted with rigid boundary conditions, creating uniform contact and near ideal axial loading conditions. These tests are used to determine the ultimate performance potential of a support, including the strength, stiffness, and stability. For prop supports where stability is a critical design issue, tests are implemented to induce buckling by a modified end condition, eccentric contact, or biaxial loading. It is important to determine the cpacity of the support design when the support is subjected to unpredictable loading conditions. This paper examines the effect of end conditions and load profiles on prop support performance and applies a new analysis methodology based on eccentric loading to determine a factor of safety for load capacity. Recommendations for installation practices that minimize eccentricity and therefore preserve capacity are also provided.

By K. S. Seljesater

SINCE the development of dispersion-hardenable lead-antimony alloys1 in the laboratories of the Western Electric Co., Inc., studies have been made of the effect of various third constituents on these alloys.2 This paper covers a study of the effect of small amounts of arsenic. This element is important since it occurs as an impurity in many commercial antimonial leads and the results obtained are particularly interesting as indicating a class of addition agents which exert a stabilizing effect on dispersion-hardened alloys. EXPERIMENTAL In order to-study the effect ,of increasing amounts of arsenic, a series of alloys were made up containing 1 per cent. antimony, and arsenic varying from 0. to 0.10 per cent., the balance Doe Run lead (99.997 per FIG. 1..-CHANGE OF MICRO-BRINELL HARDNESS WITH TIME OF 1 PER CENT. LEAD-ANTIMONY ALLOY. cent. lead). The alloys were cast into bars 1 ½ in. wide by ¾ in. thick and cold-rolled to about 1/8 in. thickness. Three samples of each composition were annealed 1 hr. at 225° C. and quenched in water. One set was aged at room temperature, one at 50° C., and the third at 100° C., the

Jan 1, 1929

By Frank J. Wiebelt, Spangler Ricker

"INTRODUCTION Bauxite, in Appalachian Alabama, occurs in the Rock Run and Goshen Valley districts in Cherokee County; in Nences Creek Valley near Jacksonville; near Anniston in Calhoun County; north of Fort Payne in DeKalb County; near Ashville in St. Clair County; and near Talladega in Talladega County.In February 1942, Preston E. Cloud, Jr., assistant geologist, Federal Geological Survey, began a study of these bauxite deposits and the geology relating thereto.The Bureau of Mines established field headquarters at Piedmont, Calhoun County, in July 1942. Mineral agreements covering a total of 11,097 acres were executed with 15 landowners in the Rock Run district; 38 in the Goshen Valley district, covering 7,575.5 acres; and 3 in the Nances Creek Valley district, covering 988.5 acres. Drilling was done on.the properties of 9 land¬owners in the Rock Run district, and on the property of 1 landowner each in the Goshen Valley and the Nances Creek districts. Drilling began October 26, 1942, and ceased on May 17, 1943.Power drilling was supplemented by a labor crew that drilled hand-auger holes in shallow deposits and sampled .old shafts, mines, and mine dumps.In all, 222 holes for a total of 13,250 feet were drilled. Of these toles, 88 penetrated bauxite but too low in grade to constitute ore."

Mar 1, 1948

US 4,132,635 -In the froth flotation beneficiation of low- grade siliceous iron oxide ore, an aqueous pulp of undeslimed ore is conditioned first with a reagent formed by incorporating a water-soluble polyvalent metal salt into an aqueous solution of sodium silicate and then with oleic acid or other anionic collector and optionally pine 011 or other frother. The conditioned pulp is subjected to flotation to concentrate Iron oxide values in the froth D. C. Yang, assigned to Michigan Technological University Jan 2, 1979 7 pp (209-1 66) Filed 1-1 3-77 (759,094) Drawing below.) [ ] US 4,133,038-In the froth flotation beneficiation of copper sulfide ore or other ores, an aqueous suspension of a mineral sample of uniform grain size and composition is conditioned with a strongly adsorbable collector in an amount which is a fraction of the amount sufficient to create a monomolecular layer on the mineral grains, and the conditioning continued until the entire amount of collector is adsorbed The conditioned pulp is subjected to flotation, the floated particles separated at timed intervals, and the flotation rate coefficient determined. By varying the degree of adsorption in repeated treatments, the dependence of the flotation rate coefficient on the degree of adsorption may be determined A Nieml Jan 2, 1979 10 pp (364-502) Filed 12-7-77 (858,353) Priority Finland, 5-26-75 (75/1,525) Same: British 1,533,723, dated Nov 29, 1978 Same Canadian 1,065,066, dated Oct 23, 1979 US 4,133,746System and method for maintaining substantially steady state conditions in the froth flotation beneficiation of copper ore, molybdenum ore, or other metal ores The mass flow of flotation concentrate from the cell is monitored continuously, and the rate of admission of aeration air into the pulp in the cell is varied inversely with respect to variations in the mass flow control of rougher flotation cells is accomplished with a single valve G W Dopson, assigned to Magma Copper Co Jan 9, 1979 6 pp (209-1) Filed 11- 23-76 (744,306

Jan 1, 1980

By T. E. Pogue

This paper traces the co-operative initiative undertaken by South Africa?s gold mining companies through the Chamber of Mines Research Organization (COMRO) in development of hydraulic technologies. After a brief description of the structure of these technologies? development under COMRO?s stewardship, the paper turns to an overview of the structure of innovation within which these hydraulic technologies were developed. A central focus of this paper is systematic review on whether similar technologies are likely to emerge in the present system of innovation and the role played by innovation policy.

Jan 1, 2006

By Louis C. Britcha

"The Phelps lease in Jasper County, Missouri, was first examined by the Bureau of Mines3/ in December 1943, at the request of Thomas Phelps of Joplin, the lessee. Owing to urgent war requirements for zinc and lead and evidence of favorable geological conditions and past productivity of adjoining properties, it,considered justifiable to explore for extensions of known ore deposits and possible undiscovered ones. In August 1944, funds were allotted for this work, which was started January 5, 1945, under the direction of the author.The provision of facilities and storage space on the property by the lessee during drilling operations is gratefully acknowledged.The Phelps lease is on land belonging to the Rex Mining & Smelting Co. It lies immediately southeast of the city limits of Joplin, Mo. It may be reached by going cast from Joplin on paved 20th street to half a mile beyond Range Line road. Twentieth street is the northern boundary line of the property, which consists of approximately 145 acres and includes the W 1/2, NE1/4, and all of the E ½. NW1/4 except 15 acres along the west side of that quarter section, of sec. 18, T. 27 N., R. 32 W., as shown on figure 1.The property is part of a 1,000-acre tract owned by the Rex Mining & Smelting Co., Paul D. Porter, president, Joplin, Mo. The lease was acquired by Thomas Phelps of Joplin, in 1937. At present the lease is controlled by a recently formed association known as the Eureka Products Co., Charles W. Madison, manager, Kansas City, Mo.Dependable skilled mine labor is scarce in the district at present, but there seems to be enough transient mine labor for small operations. The prevailing wages of the district run from 55 cents to 95 cents per hour for various types of mine labor.Living accommodations and markets to supply all domestic requirements are available in Joplin.In its program of exploration of mineral deposits, the Bureau of Mines has as its primary objective the more effective utilization of our mineral resources to the and that they make the greatest possible contribution to national security and economy. It is the policy of the Bureau to publish the facts developed by each exploratory project as soon as practicable after its conclusion. The Mining Branch, Lowell B. Moon, chief, conducts preliminary examinations, performs the actual exploratory work, and prepares the final report. The Metallurgical Branch, R. G. Knickerbocker, chief, analyzes samples and performs beneficiation tests. Both these branches are under the supervision of Dr. R. S. Dean, assistant director."

Jul 1, 1946

By D. C. Foote

MR. FOOTE: This paper deals with blasting and mechanical loading. The Union Pacific Coal Company does all of its blasting with permissible powder and electric shooting, but this paper deals principally with blasting in connection with mechanical loading. With the introduction of mechanical loading into the coal fields of southern Wyoming one of the main problems to be taken into consideration was the drilling and blasting of the coal. The methods used in blasting coal for hand loading were found to be ill adapted to the mechanical practice, so numerous tests were conducted from time to time to determine a system or systems whereby the coal might be blasted in a form to be easily handled by the loading units. The general practice in blasting coal for hand loading, for example in a room 24 feet wide and seven feet high with an undercut of seven feet, would be to shoot one or two strong breaking shots in the center and one on each rib. While much of the cut would be blasted down in good lump, some coal would be left hanging at the back and ribs. With hand loading, the miners would have time to pull this coal down with a pick between cars and eventually would clean up the place ready for the cutting machine. The loading machine, however, cannot get this coal down and its operation would be delayed while the men were doing the necessary pick work.

Jan 1, 1929

By Glen A. White

The level of impact and mitigating measures that are forecast in an environmental assessment (EA) for a new, or significantly modified, metallurgical processing facility or mine are taking on increasing importance during the subsequent life of the facility. The basic premise is that one is authorized to operate within the envelope defined by the approved EA. Operations inevitably change as they develop and mature, and at some point, one is faced with the prospect of re-doing the original EA work. This can lead to significant development delays. Cameco Corporation (Cameco) has played a major role in developing the northern Saskatchewan uranium mining industry over the past decade. Through the EA process, the company has developed ideas on what works well in generating approvals that give the operator some future flexibility. Early introduction of concepts for potentially different mining and processing methods, as well as contingency plans if things do not work out exactly as predicted in the original EA, can make subsequent regulatory approval for change a more efficient process. One must also preserve the principles of open consultation upon which the EA process was originally based. As such, involvement and support from local communities and other stakeholders is required to ensure the long-term success of the EA process.

May 1, 2004

By Minggao Qian, Jialin Xu, Wenqi Lai, Weibin Zhu

This article advances an innovative concept explaining the connotation and technical system of "green" mining. The important theoretical foundations of "green" mining are the distribution and development characteristics of joints, fractures and bed separations, and the seepage and flow behavior of methane and water in the broken rock strata following coal mining. The main focus of "green" mining technique includes water-preservation in mining areas, coal mining under buildings with bed separation spaces grouted to retard surface subsidence, partial extraction and backfill mining, simultaneous extraction of coal and coal-bed methane, coal roadway supporting and underground disposal of rock waste, underground coal gasification, etc.

Jan 1, 2005

By D Craw

Oceana Gold as part of their environmental strategy are looking at various methods for cost-effective revegetation of their tailings dams. Under the concept of revegetating the tailings this study looked at several issues. These issues were; testing different methods of revegetation, arsenic (As) uptake in vegetation with respect to capping thickness, and background As levels in farmland areas above mineralised rocks. A number of plots were set up in a temporarily disused tailings dam to trial the direct sowing of ryecorn into the tailings.   Ryecorn was sown in sandy tailings (ca 1000 mg/kg As) and then covered with oxidised schist to anchor the seeds. This proved successful and ryecorn was established. Once the plots covered with oxidised schist were growing, 1 m and 2 m strips were sown on the sheltered side of the existing plots without the covering of oxidised schist. The uncovered plots also established successfully. From this set of trials a sowing plan can be developed that uses a minimum of resources to successfully establish vegetation. The maximum As content of the ryecorn was 80 mg/kg. Clover, Yorkshire fog and ryegrass plant matter was sampled from a pot trial that used different thicknesses of topsoil covering tailings material. As the thickness of topsoil increased, the amount of As taken up decreased. Soil samples were taken from farmland areas which were known to have elevated levels of As (up to 1000 mg/kg) in the top 10 cm. Vegetation samples were also taken from the same locations, and show the As levels in plants is <50 mg/kg.

Jan 1, 2006

By Michel Ruel

"PID loops – also known as base layers or regulatory controls – form the foundation of any plant’s control layer and it is generally accepted that PID loop health has a direct impact on the plant’s bottom line. Keeping these thousands of control loops in good health has a direct impact on the plant’s bottom line: it reduces variability, improves quality and throughput, and decreases energy costs and raw material usage. This has been well proven and documented in many articles. In the last ten years, technology has evolved: control engineers can now keep track of control loop performance and link it to the root causes of variability. However, they lack industry-wide best practices and criteria for determining what can be considered as excellent, good, fair, or poor performance. To ensure that PID control loops continue to perform well and meet their objectives, control engineers need a combination of (a) an appropriate monitoring technology and (b) best practices for doing the maintenance of base layer controls.Most plants have limited resources and operate with an increasing number of constraints; therefore, using the right tools and including reports in daily workflow is key for success. This paper suggests roles and responsibilities of key players needed to work toward control performance best practices and discuss organisational changes to succeed.INTRODUCTIONAlthough PID controllers are reliable workhorses in the process industry, they are often underrated. Since the 1980’s, computer control has evolved and the control algorithms used by control engineers have become increasingly complex. However, PID controllers still handle over 90% of the control loops in operating plants. Table 1 shows the savings that can be realized by achieving best-practice in several different process control categories (Brisk, 2004). The savings are expressed as a percentage of production costs."

Jan 1, 2011

In surface mining operations, ultra-heavy trucks operate on haul road networks which are typically from 10?40 km in length. These road networks are often not optimally designed and maintained and as a result, identifying and remediating road functional defects is problematic. Most surface mine operators agree good roads are desirable, but find it difficult to translate this into an effective road maintenance system. This paper presents a haul road maintenance management system which utilizes an assessment of rolling resistance based on a functional performance evaluation of a haul road, together with mine haul truck operating cost models to derive the optimal frequency of road maintenance. A typical application is presented which illustrates the potential of the technique to manage maintenance as and where needed with resultant reduction in total road user costs and an improvement in service provided for the road user. Keywords: Haul road, surface mining, road maintenance, transportation, pavement design

Jan 1, 2003

By G. David Baskin

Changes in the 1978 quantity and value of the sales of various natural abrasives, compared with the data for 1977, were of a mixed nature. Output of tripoli-type materials and garnet increased in both tonnage and value. Emery production also increased. But special silica stone product sales decreased in both tonnage and value, and the reported quantity and value of sales of manufactured abrasive material also decreased for 1978. In 1979 output of tripoli-type materials and special silica stone products decreased in both tonnage and value when compared with the previous year. The tonnage and value of sales of garnet and manufactured abrasives increased when compared to 1978 data.

Jan 1, 1980

By J. L. Yordan, J. Kortmeyer, I. Yildirim

Talc is used to remove stickies from pulp during paper recycling processes. It is well known that the interaction is controlled by the surface chemistry at the talc/water, sticky/water and talc/sticky interfaces. If the interfacial tensions are known, one can calculate the free energies of interaction and hence predict whether the stickies can be removed by talc. In the present work, the surface tensions of several different talc samples were determined using the acid/base theory. The information was then used to determine appropriate interfacial tensions, which in turn were used to determine the free energy of interaction between talc and stickies. It was found that the calculated free energies are much more negative than those between the stickies and other minerals such as calcium carbonate, bentonite clay and kaolin clays.

Jan 1, 2002

By S. Mundike

A scraper-based block cave method has been successfully applied to extract the Lower orebody at Nchanga since the 1950s. Since inception, scraper drifts and service ways have been supported using steel arch sets fabricated to a specific design from high strength manganese steel To reduce costs and to improve productivity, trials commenced in 2002 using fibre reinforced shotcrete as an alternative support method. One of the areas, the 2420 8E 1C trial drift, was subjected to abutment loading for several months prior to undercutting and cave mining. Shotcrete installed exhibited minor cracking shortly after application but very little deterioration thereafter. Following the success of the trial, the application of fibre-reinforced shotcrete was extended to other drifts. This paper describes the application of fibre-reinforced shotcreteat Nchanga and outlines design and quality assurance methods employed.

Jan 1, 2005

This paper reviews ore pass practice in some Canadian mines in Quebec and Ontario. In particular it reviews ore pass configuration, flow control mechanisms and monitoring practice. A review of the type of problems encountered and the tools to restore flow is also presented.

Jan 1, 2005

By M. Djivre, T. Eger, A. Godwin, I. Bhattacherya

Load-haul-dump vehicles (LHDs) are extensively used in underground mining, however, equipment design and operating conditions contribute to restricted operator sight lines. The inability to clearly see people, objects, or hazards around the machine has contributed to a number of accidents including fatal injuries. In order to identify vehicle design characteristics resulting in restricted and blocked sightlines, line-of-sight assessments are traditionally completed in the field. However, field methods are unable to evaluate lineof- sight under dynamic operating conditions, and are limited in their ability to provide feedback on the impact of various operator characteristics such as sitting height. Results of this research show computer simulation and virtual reality can be successfully used to evaluate line-of-sight during the operation of LHD vehicles. In order to benefit from virtual reality applications, the work environment, LHD vehicle, and human posture need to be represented as accurately as possible. A computer simulation program with ergonomic analysis features, Classic JACK 3.1, was successfully used. Threedimensional CAD models of LHDs were developed from manufacturer specifications and pictures taken from LHDs currently in use. The LHD models were imported into the JACK environment, a digital human was positioned in the cab of the LHD vehicle, and the vehicle and human were driven over a typical mine route. Real-time feedback in the JACK program was used to identify what the operator could see under different operating conditions. Machine characteristics and operating scenarios resulting in impaired line-of-sight were successfully identified with this method. The JACK program could also provide real-time feedback on the human’s joint forces and torques, strength requirements, postural comfort, and metabolic energy expenditure. As a result, this method could be used to successfully evaluate musculoskeletal injury risk factors along with system design recommendations to improve workplace safety and productivity in any setting. The LHDs evaluated in the JACK software package can also be combined with mine models and imported into other VR software packages (e.g. Blender) in order to enable viewing in Laurentian University’s Virtual Reality Laboratory. The VR models using these packages can be viewed in stereo to provide better appreciation of spatial vision issues.

Jan 1, 2005

By A. Mitchell, T. Bagshaw

A recent paper by Thomas1 has presented new data on the solubility of hydrogen in solid silver at 1 atm pressure in the temperature range 600° to 963°C. However, no data is reported in the literature on hydrogen solubility in liquid silver. The Sieverts technique which has been described previously2,3 was used in the present work. Charges of approximately 160 g were melted in Morgan "purox" recrystallized alumina crucibles and purified helium was used for the determination of the "hot volume" during each experiment. A chemical analysis of the silver indicates that the impurity content (Cu + Al) is less than 0.02 wt pct. Hydrogen solubility in the temperature range 963° to 1200°C was investigated. The results of three experiments are shown in Table I. Fig. 1 shows an Arrhenius plot of the present work together with the solid-state data of Thomas, Steacie, and johnson,4 Eichenauer et al.,5 and Siegelin et al.6 The following expression has been derived from the Arrhenius plot of the present data: log (solubility of hydrogen, cm3 per 100 g) = 2.154-3512.0/ToK The heat of solution derived from Fig. 1 is 31,150 cal per g mole H2 compared with the value of 33,020 cal per g mole H2 obtained by Thomas and 12,000 cal per g mole H2 obtained from the data of Steacie. It was observed that hydrogen evolution took place when the silver melts were solidified under 1 atm of hydrogen, which would not be expected from an extrapolation of the results of Steacie. Schenck and Lange7 have observed that, for several transition metals at their melting points, the ratio of the hydrogen solubility in the liquid to that in the solid lies in the range 2.1 to 3.1. The present results and those of Thomas are in accord in this respect having a ratio of 2.8. 'C. L. Thomas: Trans. TMS-AIME, 1967 vol. 239, pp. 485-96. 2T. Bagshaw and A. Mitchell: I. Iron Steel Inst., 1966, vol. 204, p. 87. 'M. Weinstein and J. F. Elliott: Trans. TWS-AIME, 1963, vol. 227, p. 382. 'E. W. R. Steacie and F. M. G. Johnson: Proc. Roy. Soc. (London), Ser. A, 1928, vol. 117, pp. 662-79. 'W. Eichenauer et al.: Z. Metallk., 1958, vol. 49, pp. 220-25. 6W. Siegelin et al.: Z. Elektrochem., 1957, vol. 61, pp. 359-66. 'H. Schenck and K. W. Lange: Arch Eisenhuettenw., 1966, vol. 37, no. 9, pp. 739-48.

Jan 1, 1969

By B. Derin, T. Uzunoglu, O. Yücel

In this study, reduction behaviours of Turkish chromite concentrate (48 % Cr2O3, 13.30 % FeO, 18.33 % MgO, 12.37 % Al2O3, 5.76 % SiO2) and nickel oxide by Fe-C alloy in graphite crucible were investigated. In the first stage of experiments, steel scraps were melted in graphite crucibles and were saturated with carbon at 1600 °C and 30 min. In the second stage, mixtures of different amount of chromite concentrate, nickel oxide and flux additives (CaO,SiO2 and CaF2) were charged into the graphite crucible containing the Fe-C alloy and heated to 1600 °C for different reduction times (0-180 min) under argon gas. The highest Cr and Ni con-tents in alloys were found as 11.41 and 14.37 % and the highest Cr and Ni recoveries were found as 88 and94 %, respectively at 180 min.

Jan 1, 2007

By Filiberto Fernández

El presente texto señala el proceso de estabilización de las altas eficiencias de corriente en la refinería de Southern Perú a través de los hornos, el desarrollo en los cátodos producidos y su apoyo del personal de mantenimiento, operaciones y producción. De forma, que utilizando esta política, la refinería ha incrementado la densidad de su corriente, controla mejor sus procesos, control físico y las pruebas de investigación en forma ordenada, eficaz y efectiva.

Sep 13, 2001