Search Documents

By J. Jordan, D. K. Denton, D. Tesarik, D. F. Scott, T. J. Williams

Personnel from the Spokane Research Laboratory of the National Institute for Occupational Safety and Health integrated the results of studies from a seismic tomographic survey, a finite-difference analysis, laboratory measurements of compression wave (ultrasonic) velocities in rock cores, and site geology to evaluate the use of seismic tomography for identifying induced pressures in an underground pillar at the Edgar Mine, Idaho Springs, CO. The key findings were that (1) the seismic tomograms showed that seismic velocities in rock adjacent to mine openings were low, (2) a difference tomogram in which in situ stresses on the east and west sides of the slot were compared showed that velocities increased west of the slot but decreased east of the slot, (3) geologic features (rock types and a fault) identified through geologic mapping were recognizable in the seismic tomograms, (4) ultrasonic velocity measurements on the rock cores agreed with seismic velocity measurements in the tomograms, and (5) results from a finite-difference analysis compared well to the seismic tomograms west of the slot but not east of the slot. The significance of this research is that seismic tomography is a useful tool for determining relative stress in underground pillars.

Jan 1, 2004

By V. C. Pandolfelli, S. F. Santos, L. A. Rodrigues

Under conditions of stable crack propagation at room temperature, the elastic energy stored in ceramic materials is converted mainly to surface energy. However, at high temperatures, creep may also occur in such materials, in which case it will present a ductile behavior. This paper discusses the brittle-ductile transition of a refractory material. Stable crack propagation and creep tests were carried out under a three-point bending device. A commercial ceramic containing 63 wt-% of SiO2 and 31 wt-% of Al2O3 was used as testing material. The results revealed that the change in behavior from brittle to ductile was caused by softening of a vitreous phase present in the material's microstructure.

Jan 1, 2004

By D Craw, S Clearwater, S Hammit, C Smith

Prior to rehabilitation, plant cover on quartz gravel overburden at Wangaloa coal mine was highly patchy. Stabilisation techniques have since considerably altered the condition of the main overburden yet deposits in the east and west remain largely intact. On the eastern overburden, three distinct zones of revegetation have naturally developed: Zone 1 represents a dense plant cover, Zone 2 a patchy cover and Zone 3 a sparse cover of isolated plants. Aerial photographs show much of the eastern overburden was deposited between 1940 and 1960s. Yet we found that the temporal scale of deposition did not wholly account for the differences observed in vegetation development. To investigate other influential factors, we set up 12 study plots using four replicates in each vegetation zone. The diversity and density of plants in each plot were measured to quantify the degree of vegetation development. Samples from the substrate in each plot were collected using soil cores to a depth of 10 cm. Cores were analysed for indicators of nutrient availability, metal content and physical composition. We found that substrate chemistry varied between individual study plots, but showed little difference overall along the vegetation gradient. Substrate physical differences were much greater. The ratio of coarse quartz pebbles: fines was considerably higher in Zone 3 than other zones, and within zones where plants were not growing. Bulk density also increased successively from Zone 1 - 3. We found clear evidence for the reversed stratigraphy of excavation superimposed over the time scale of deposition, and the corresponding nature of fine particles. The rate of revegetation was therefore highly dependent upon the substrate composition of the last surface deposit from the dumping truck. Our data suggests an optimum ratio exists between inert coarse material and a fine matrix for progressive natural vegetation development on mine substrates.

Jan 1, 2004

Founded in 1994 through a joint effort between Underwriters Laboratories Inc. (UL), the U.S. Consumer Product Safety Commission (CPSC) and the National Electrical Manufacturers Association (NEMA), the Electrical Safety Foundation International (ESFI) is North America?s only non-profit organization dedicated exclusively to promoting electrical safety in the home, school and workplace. ESFI is a 501(c)(3) organization funded by electrical manufacturers and distributors, independent testing laboratories, utilities, safety and consumer groups, and trade and labor associations. ESFI sponsors National Electrical Safety Month each May, and engages in public education campaigns and proactive media relations to help reduce property damage, personal injury and death due to electrical accidents. The Foundation does not engage in code or standard writing or lobbying and does not solicit individuals.

Jan 1, 2004

By J. F. Papp

In the United States, chromium has been consumed in three major markets: chemical, metallurgical, and refractory. The predominant end use for chromium in the United States is in the metallurgical market as an alloying element in the production of stainless steel. In addition to being a major stainless steel-producing country, the United States is a major world producer of chromium-containing chemicals and has used substantial amounts of chromite ore for refractory applications. Chromium use is not easily further subdivided within the chemical and refractory industries because there is insufficient publicly available information to do so; however, chromium use can be subdivided among metallurgical industry uses based on the American Iron and Steel Institute (AISI) reported shipments of stainless steel by market classification (agricultural, aircraft, automotive, etc.). It is the goal of this study to determine the distribution of U.S. chromium apparent consumption among major markets in the United States. The distribution is expressed in the form of dimensionless fractions that are computed based on documented chromium consumption by major market. The distribution of chromium among markets within the metallurgical market is computed in a similar manner. Distribution factors are first computed for the major markets, then for markets that are subdivisions of the metallurgical market. The distribution of chromium among major markets has changed substantially over the time period of analysis. The fraction of chromium consumed by the metallurgical market has increased while that of the chemical and refractory markets has declined. Within the metallurgical market, the service industry market accounts for the greatest fraction of chromium consumption followed by transportation. Electrical, machinery, and fabricated products markets account for a substantial share of the metallurgical chromium consumption.

Jan 1, 2004

The Beruang Copper-Gold Deposit is located very near the centre of Kalimantan in Indonesia. It is a dacitic tuff hosted deposit currently being explored by Kalimantan Gold Inc of Canada. Exploration activity to date at Beruang has been focused on the Main Zone, which is defined by a north-south elongate, 1 + 1.5 km zone of anomalous copper and gold, and intense phyllic alteration. The disseminated sulfides responsible for the anomalous copper values produce a moderate to high chargeability signature. Phyllic alteration is overlain at high levels, and on the western edge of the Main Zone, by advanced argillic alteration. The dacite tuffs hosting the mineralisation are cut by post-mineralisation dacite dykes that are delineated by ground magnetics and geological mapping. Base metals, principally zinc and lead, form broad halos around the Main Zone. These metals are incorporated in massive NE-trending, polymetallic mineralisation that outcrops to the north and south of the Main Zone. IP survey results highlight the highly pyritic NNE-trending shear zone, which hosts most of the copper mineralisation in the Main Zone. A high chargeability anomaly at depth in the central-east part of the Main Zone is interpreted to be the source for mineralising hydrothermal fluids. This is suggested by zonations in alteration and mineralisation. A deep chargeability anomaly can be correlated with the downward plunge of a pyritic breccia, encountered at shallow levels in drillholes, and is a potential breccia pipe target. Compilation and inversion modelling of the IP results has yielded some interesting drill targets.

Jan 1, 2004

The theme at this yearÆs AusIMM New Leaders Conference in Ballarat was æThe Minerals Industry û Future Directions for New LeadersÆ. There was a strong focus on the recruitment and retention of trained and skilled graduates and new professionals into the mining profession. This paper highlights some of the key findings and discussion points from the New Leaders Conference. While some of the main causes of the decline in attracting new geoscientists to the mining industry have been identified, there still remains a lack of accountability among a number of Australian mining companies. Some of the factors identified that are driving new graduates away from the industry include; the social and geographical isolation, the long hours in challenging conditions and a difficulty in obtaining work straight out of University. Often there appears to be no clear opportunities within companies for career development and advancement. The opinion also still persists that the mining industry is lagging behind in both environmental and technical developments, which makes entry to the industry unattractive. Solutions that some of the large players in the Australian mining industry are implementing to help reverse the trend include targeted marketing of the lifestyle, money, freedom and travel offered in the mining industry, the development of graduate recruitment programmes and much more emphasis on the quality and reputation of the companies themselves. Incentives to attract families have also been significant in attracting and retaining employees whom otherwise would have left the workforce. However, more still needs to be done to completely reverse this trend and the mining industry needs to continue to be proactive in marketing itself as a desirable employer and career choice option for students and new professionals.

Jan 1, 2004

By N. Hmidi, T. Yalcin, M. Papadakis, B. Hilscher

Mill tailings, containing iron sulphides in particular, pose an environmental concern since they constitute a potential source of acid mine drainage which can damage vegetation, harm soil and living organisms, and contaminate groundwaters. Proper disposal of acid generating tailings is therefore an important issue that must be addressed and resolved in a satisfactory manner. Placer Dome Canada operates a 4000 t/d gold cyanidation facility at Musselwhite mine, in northwestern Ontario, where the mill tailings have been classified as acid generating. This study was conducted to explore the effectiveness of froth flotation in removing the sulphide minerals from these tailings and producing a low-sulphur, non-acid generating material that could serve as a capping material for previously deposited tailings. Laboratory semi-batch flotation tests were carried out in accordance with an experimental design procedure, and a computer simulation program was developed to facilitate the evaluation of flotation performance. In this investigation, pH, collector concentration, and airflow rate were considered as the relevant flotation variables, and their effects were examined both experimentally and by simulation. Results have demonstrated that flotation can successfully desulphurize the Musselwhite mine tailings and render them non-acid generating.

Jan 1, 2004

By C. C. Russelll, V. T. McLemore

The Metals Mining Sector of the Acid Drainage Technology Initiative (ADTI-MMS) addresses technical drainage-quality issues related to metal mining and related metallurgical operations, for future and active mines, as well as, for historical mines and mining districts. One of the first projects of ADTI-MMS is to develop a handbook describing the best sampling, monitoring, predicting, mitigating, and modeling of drainage from metal mines, pit lakes and related metallurgical facilities based upon current scientific and engineering practices. One of the important aspects of planning a new mine in today’s regulatory environment is the philosophy of designing a new or existing mine or expansion of operations for ultimate closure. The holistic philosophy taken in the ADTI-MMS handbook maintains that sampling and monitoring programs should be designed to take into account all aspects of the mine-life cycle. Data required for the closure of the operation are obtained throughout the mine-life cycle, from exploration through post-closure.

Jan 1, 2004

By Y. M. Shneerson, V. M/ Shpaer, E. E. Zhmarin, A. Y. Lapin, E. M. Vigdorchik

This paper describes studies of zinc concentrate oxidizing pressure leaching using the method of mathematical modeling. The concept of a kinetic function was taken as a basis for mathematical modeling of the leaching process. The kinetic function describes dependence of the unreacted component share OJ on the relative time x (the relative time is the ratio of the test duration and the time of complete dissolution). This kinetic function is determined in accordance with the results of batch laboratory tests. The laboratory tests have been carried out on zinc concentrate produced from Kazakhstan zinc-copper ores. Zinc concentrate consisted mainly of three types of minerals: sphalerite (70%), pyrite (13%) and chalcopyrite (10%). Oxidation reactions of sphalerite, pyrite and chalcopyrite have been considered as principal ones. The kinetic characteristics of the process (kinetic function, reaction order, activation energy, duration of complete dissolution of the concentrate components) have been calculated in the course of laboratory tests. The mathematical model was used for estimation of the main technological leaching process parameters (such as process rate, degree of metals extraction, autoclave capacity, heat balance, etc.). Mathematical modeling based on the kinetic function concept allows safe designing of metallurgical equipment and scaling the technology to industrial capacity.

Jan 1, 2004

I attended a funeral in West Monroe, Louisiana, for one of the best powder peddlers I’ve ever known. He started work in 1948 for Dixie Dynamite, a seismograph explosive distributor. His first job was as a truck driver, then magazine keeper and then sales re p re s e n t a t i v e . When Dixie Dynamite quit, he acted as an explosives sales agent for sometime before moving on to Kansas to be a sales rep for a distributor there. We called him the “ragin cajun” long before James Carville came on the national scene messing up things. While he was born in G e o rgia, he was a Cajun at heart. I don’t believe the old saying, “Build a better mousetrap and the world will beat a path to your door.” To me, the best products in the world need to be sold. Two examples of this are the Beta system for TV and the Apple Macintosh computers. Beta is the best system but VHS took over because the Beta people fell down on the selling job. Windows 98 is Macintosh ‘86 but again the engineers were not salesmen. Marion “Johnny” Johnson who was buried only about a half mile from his first magazine site proved that good selling is good citizenship. He could have sold any firstclass product, for he wouldn’t tolerate inferior items, and made a successful career of it, but he chose dynamite and the industry benefited from his talents.

Jan 1, 2004

By J. B. Rubenstein

This work demonstrates the feasibility of using confocal surface profilometry to measure and characterize wear of graphite anode surfaces. This method was tested using anode samples that were electrolyzed for 24 hours in a laboratory-scale magnesium cell with a high oxide molten salt electrolyte. The oxide produced accelerated wear on anodes designed for low oxide electrolytes. Contour maps, which are effective at displaying non-uniform wear, and total graphite consumption values were generated from the collected surface coordinates. Along with both qualitative and quantitative analysis capabilities, this measurement system was shown to have a fine resolution and a low detection limit.

Jan 1, 2004

By A. Ardiant, C. E. F. Mumbunan, I. Irawan

As a part of mine operation’s success key, Community Development nowadays seems to be a rule of thumb. Not only is for a short term need of the company during their operation but also for the national public opinion on the presence of the mining industry to a certain region. Nanggung region which is only a 2-hour drive from Jakarta, brings the challenges to Antam’s gold mine business in the areas such as illegal miner presence, easy access to the mine area as it is very close to the community, and national political sensitivity considering its proximity to Jakarta. The company allocates about 3%of its total operational cost annually for Community Development pro-gram. The program is derived through SWOT analysis and broad involvement of all community components to assure that the allocated fund is addressed to the right place. In the year of 2002, the company has successfully established a conducive-relation with the community.

Jan 1, 2004

By W Farnworth, D Fergusson

Estimation of productivity is a key factor in the design of hydraulic mines and in assessing their economic feasibility. A published Russian formula for hydraulic mining monitor cutting rates overstated productivity by up to 2 tonnes per minute (251%) when applied to Solid EnergyÆs hydraulic mines. A new formula, taking into account additional productivity factors, was derived by Solid Energy and produced an acceptable correlation between predicted and actual cutting rates inNew Zealand and overseas hydraulic mines, with an average error of approximately 0.1 tonnes per minute.   Another key factor in hydraulic mine design is the transport of coal slurry via flumes. Solid Energy carried out a series of 80 full scale tests in a surface flume installation, varying the gradient and coal:water ratio. Both steel flumes and plastic-lined flumes were evaluated. A modification of the Chezy Open Channel Flow formula, including a factor for slurry density, gave a reasonable correlation between actual and predicted flows. It is believed that this Solid Energy formula is suitable for the design of flume installations for hydraulic mining.

Jan 1, 2004

By J. I. Mathis

"The failure that was utilized for developing this model was a double bench-scale failure, approximately 20 m in height, in the Misery pit at BHP Billiton’s EKATI mine site. The bench that failed was excavated in biotite schist. Due to previous problems with bench-scale toppling failures, this bench was excavated with a 70° inclined, 30 m deep preshear. Upon exposure, the wall was very clean with half-barrels commonly observed from the pre-shear operation.In August 2003, a bench failure of about 1000 t occurred in this pre-sheared biotite schist (Fig. 1). Upon examination it was noted that the foliation that paralleled and dipped at 70° into the face when excavated was approximately horizontal at the top of the failure (Fig. 2). While the failure mode itself appears complex, the failure was apparently driven by three factors:• a low-angle, low-frictional strength fault or discontinuity at the base of the failure area;• water either contributed meteorically from precipitation and/or from permafrost melt; and• foliation planes providing a viable toppling geometry once toe block motion began to occur.The above details are illustrated in Figure 3.After considerable thought and analysis, a model was postulated for the failure.It is thought that the entire failure had been triggered by displacement of a toe block (Fig. 4). This toe block is bounded on the back by foliation, the bottom by a low-angle, lowstrength fault, and the front by the bench face. Water pressures behind the bench face developed forces on the block as can be seen in Figure 5. These forces were sufficient to induce block motion. As can be seen in the relative shear strength diagram in Figure 6, only a small amount of water is necessary in the face to initiate block displacement. Note that in this figure, a simplistic piezometric pressure distribution was assumed."

Jan 1, 2004

By B Siddall, A Gunstone

The use of a partial secondary crushing circuit provides a flexible way to optimise existing SAG comminution circuits limited by rock competency or enables optimal processing of an ore through second hand equipment not specifically selected for that ore. This paper details the process involved in designing a partial secondary crushing circuit using the recent installation at Mt Rawdon Gold Mine in Queensland as an example.

Jan 1, 2004

This paper provides an expanded definition of industrial minerals that challenges the way we look at exploration, development and the understanding of mineral industry structure and profitability. Included in industrial minerals are bulk commodities such as iron ore and coal alongside the more traditional industrial minerals such as salt, soda ash, silica sand and clay. The profitability of industrial minerals is reviewed from a producerÆs perspective and shown in many instances to be significantly higher than for precious and base metal industries. The key drivers of profitability are examined along with some highly profitable industrial mineral industries such as borate, potash, chromite and natural soda ash. Demand for industrial minerals in Australia and Asia is reviewed, with a focus on supply bottlenecks and the opportunity this represents for investment by Australian companies. The establishment of new price benchmarks is considered and the possibility of new export grades for industrial mineral products. Investment opportunities in industrial mineral projects are outlined, including some exploration concepts in Australia and Asia. Industrial mineral project evaluation methods are discussed and the challenge issued to companies (exploration, production and finance) to become a part of the profitable action in the world of industrial minerals.

Jan 1, 2004

By P Storey, B Deans, T Lancaster

Straits completed its Feasibility study on the Whim Creek Copper Project in 1996. At this stage WCCP provided Straits with an open pit mine - heap leach - SX-EW copper project to follow on from its successful Girilambone Copper Operation (GCC). Since this time Straits has continued to review WCCP investigating a number of development and production scenarios. The development of Whim Creek, early 2004 and is on schedule to commence copper production in the final quarter of 2004. On current reserves Whim Creek will produce approximately 17 000 tonnes of copper cathode per annum for three to four years, at cash costs of The paper will cover a general description of the project, the project development and key design issues. Additional construction related issues associated with the complete relocation of the GCC plant to Whim Creek will be covered in the conference presentation.

Jan 1, 2004

By Joseph J. Zaluski, J. Steven Gardner, Marco M. Rajkovich

The telephone rings at 3:20 a.m. An exasperated voice on the other end says, “There has been a mine explosion at Mine No. 5 and we have not heard from three units of men.” Twenty-three minutes later, the phone rings again and another panicked voice says, “There is something wrong at the slurry impoundment, the pool level has just dropped five feet and we are trying to figure out what is wrong” Thirty minutes later, the mobile phone rings. An excited security guard says, “We have reports of thick black water running down the right fork and left fork of Straight Creek and both seem to be rising in the banks.” If this is not enough excitement, the mobile phone rings again. A stressed company official says, “I just heard a report that black slurry is running out of the portals of XYZ Co. No. 2 Mine, which is adjacent to our No. 5 Mine.” Is this all some kind of dream or nightmare? More importantly, though, if this happens, what do you do? Most people think: “It can’t happen to me.” But mine explosions do happen, slurry impoundments can rupture and creeks can flood with black water causing damage to others, including competitors. A mine’s response must be quick, cool-headed, calculated and effective. This article examines the issues, concerns and ramifications of this hypothetical disaster. The authors then present a systematic crisis-management response.

Jan 1, 2004

By W. D. Gould, A. Kapoor, K. Morin, P. Bédard

This paper presents the results of a research study that is being conducted by the Mine Effluents Program, Mining and Mineral Science Laboratory (MMSL), Natural Resources Canada aimed at evaluating biotechnology processes for the treatment of nitrogen compounds such as thiocyanide (CNS) and ammonia (NH4-N) which are present in gold mill effluents. A sequencing batch reactor (SBR) technology, commonly used for the biological treatment of municipal and industrial effluents, was used in this study. In the SBR process, the micro-organisms were able to degrade CNS to NH4-N and NH4-N to nitrate (NO3-N) at operating conditions of two 12 h treatment cycles per day, with pH maintained in the 7.4 to 7.6 range, and at room temperature (approximately 21°C) and also at 12 °C. The end products of CNS and NH4-N biological oxidation were NO3-N and sulphate (SO4) that are relatively non-toxic. Partial removal of NO3-N was achieved by biological denitrification reactions in the SBR process. The SBR process effluent was measured to be non-toxic to rainbow trout based on the 96 h acute toxicity test. The microbial consortium isolated from the SBR treating a simulated effluent was able to effectively oxidize CNS and NH4-N to NO3-N in water samples (under batch conditions) collected at three mine sites located in Quebec, the Northwest Territories, and Yukon.

Jan 1, 2004