Search Documents

By Fred N. Kissell

In This Chapter [Ventilation and methane sampling guidelines for conventional shafts Dealing with restricted spaces where methane can accumulate Ventilation and methane sampling at raise bore drills and Filling shafts at closed coal mines] It is not unusual to encounter methane gas during shaft excavation or shaft-filling operations. Shafts into coalbeds usually produce the most methane, so the information in this chapter applies primarily to shafts at coal mines. Nevertheless, much of the information is relevant for noncoal mines that have methane in the mine or in the overlying strata. METHANE IN SHAFTS EXCAVATED BY CONVENTIONAL MEANS (DRILL, BLAST, MUCK) [ ] Ventilation. Shafts excavated by conventional means are ventilated with a fan on the surface connected to ductwork that extends down into the shaft (Figure 9–1). Shafts into coalbeds should have ventilation systems designed to handle the higher gas flows to be expected as the shaft excavation passes through any over-lying gas-containing strata and nears the coal-bed to be mined. Following are some simple ventilation guidelines for the minimum amount of air required and the selection of the ventilation duct: • Provide enough air to meet the mini-mum OSHA tunnel requirement of 30 ft/min air velocity in the open shaft, as specified in 29 CFR2 1926.800(k)(3). For example, a 20-ft-diam shaft having

Jan 6, 2006

By Fred N. Kissell

In This Chapter [Measuring the gas emission from the coal Methane at the top of the silo Methane at the load-out area and Actions taken after a silo explosion] Methane accumulations in coal silos have resulted in the occasional silo explosion. These can be quite violent and dangerous because coal dust adds to the strength of the blast. However, with the appropriate precautionary measures, methane accumulations in silos can be greatly reduced. Mine Safety and Health Administration (MSHA) regulations at 30 CFR2 77.201 require that the methane content in the air of any coal silo be maintained below 1.0 vol %.3 Also, MSHA requires that methane tests be conducted before any electrical equipment is energized, unless a continuous monitor capable of deenergizing the electrical equipment is used.4 Measuring the gas emission from the coal. The first necessary step in dealing with silo methane issues is to measure the gas emission from the coal going into the silo. Such measure-ments allow one to estimate the silo ventilation needs and permit a comparison with the methane controls used at other mines that have similar gas levels. The gassiness of the coal can be measured by taking conveyor belt grab samples.5 Matta et al. [1978] measured the gas emission from conveyor belt grab samples using a simple desorption test. To conduct the test, they collected several grab samples of coal, weighing a few pounds each, from the conveyor belt entering the silo.6 They then sealed the coal into an airtight sample container that was equipped with a valve and short hose along with a pressure gauge. Every few hours they opened the valve and bled the emitted gas into a water-filled graduated cylinder that had been inverted and placed in a pan of water (Figure 11–1). The results are shown in Figure 11–2.

Jan 6, 2006

By Edward Ernst, Richard Runvik

AT the U. S. Gypsum Co. mine in Oakfield, N. Y., a flat-lying vein of rock gypsum is mined by the room and pillar method. Averaging only 4 ft thick, this vein is 1200 to 6000 ft in mineable width and many miles in length. Overlying the vein throughout the mine is a 2-ft thickness of distintegrated gypseous shale and fractured limestone which parts easily, falling with little or no warning. This shale, known as ash, varies in thickness from less than an inch to more than a foot. Small veinlets of selenite cut this shaley material, which breaks around timber props. The 18-in. limestone over-lying the ash is fractured vertically into blocks of varying size and will fail if any but the shortest unsupported spans are permitted. Above these two members is a thick layer of competent limestone.

Jan 6, 1957

By D. W. Evans

Mine subsidence problems due to coal extraction have occurred in a number of areas throughout the United States. Depending on the local geology, the depth of the mined seam, the type of mining method employed for extraction, and other related factors, subsidence can result in anywhere from slight displacements to a total loss of ground. These conditions can have serious consequences on the health and safety of the people living above the mined areas. A number of methods exist to provide support for the ground overlying mines. All of these methods employ some mechanism for providing additional support to either the roof of the mine or the sides of the pillars. Since failure usually occurs due to overburden stresses which are transmitted to the roof and pillars, these methods employ techniques to counteract stresses induced due to the coal extraction. The applicability of any particular method will depend on the availability of backfill material, the areal extent of the affected area, and of course, the cost. The primary use of coal ash for subsidence control has been as a backfill material for the stabilization of large areas. Large scale backfilling projects for subsidence control have been performed in Rock Springs, Wyoming, Wilkes-Barre and Scranton, Pennsylvania, and in Fairmont, West Virginia. Some of these projects have utilized sand, as well as, coal ash as backfill material. Much of the backfilling work performed in the United States has been done in an effort to control mine subsidence in abandoned mines. South Africa, on the other hand, has used backfilling extensively both for ash disposal and to increase extraction in active mines. The utilization of repetitive fill and mine techniques has resulted in extraction increases of as much as eight percent in shallow mines and as much as twelve percent in deep mines.(1) The coal ash injection system which can be used for backfilling depends largely upon whether the mine voids are dry or submerged. For dry mines, hydraulic or pneumatic conveyance systems can be used, while submerged mines are limited to backfilling by hydraulic methods. The use of coal ash as a backfill material has a number of advantages, such as: 1. Coal ash is available in areas throughout the United States and in many instances is conveniently located near areas requiring backfilling. 2. Coal ash is available in significant quantities since many coals when burned will result in about 15 to 30 percent ash by weight. 3. Coal ash as backfill is, in many instances, the most economical alternative fill material. Due to the costs associated with above ground disposal, power companies will often times give the material away to lower their overall operating expenses. 4. Coal ash is usually pozzolanic in nature, that is, this material results in cementitious bonding within the backfilled matrix of material.

Jan 1, 1982

By Brian Flintoff

Basic process control is an integral part of most mineral processing plants. It is widely acknowledged to have helped many operations reduce costs and increase productivity and performance. The research community is very active in the development and evaluation of both model based and Al techniques for advanced control applications. Vendors and specialist consulting or engineering firms are in business to help deliver these solutions to the plant floor. It would seem that there is a good balance between business needs and technology, and that the industry should be moving steadily forward in an aggressive pursuit of plant-wide automation. However on closer examination one sees some systemic problems which are sewing to inhibit progress. One of the mist obvious manifestations is the gap which exists between the available technology and current This paper explores the control of mineral processing systems, with a particular emphasis on some of these problem areas.

Jan 1, 1995

By D Gelling

Mineral sands dry plants consist of a large number of repetitive unit operations with significant transport delays, in the form of stream pipes, conveyors and elevators. As part of the P255 mineral sands sponsorship and using the JKMRC developed conductor/non-conductor (CNC) gauges, control loops have been implemented at the multi-duty dry plant of Cable Sands Limited at Bunbury. This paper describes the loops for kV control on a rougher high tension roll machines (HTR). The options available are product grade control and ratio control using the JKMRC CNC gauges, which measure the percent conductors in a stream. The purpose of control is to stabilise the circuit operation against disturbances such as atmospheric and feed disturbances.

Jan 1, 2001

By Ira B. Jorafemon

In the interesting Institute symposium of the preservation of peace by force, through mineral control, one important aspect of the question was not presented. This is the responsibility the United Nations, and particularly the United States, will incur the through limitation of the economic activities of nations that are now friendly to us, as well as of nations that are enemies or are under the control of enemies. After the war all nations, friends as well as enemies will be poor. Hunger and bankruptcy will, will like the sword of Damocles, hang over the heads of all of us on this blundering planet. When the actual fighting is over, there will be a universal attempt to squirm out from under the sword by resuming production of peacetime goods, for trade as well as immediate consumption.

Jan 1, 1944

By J. E. Spencer

Mesozoic and Tertiary mineral deposits in west-central Arizona are commonly associated with Mesozoic thrust faults and Tertiary detachment faults, respectively. Quartz-kyanite rocks and pyritic quartz-sericite schists with local anomalous gold are the product of probable Jurassic argillic alteration of Jurassic volcanic, sedimentary, and plutonic rocks followed by Cretaceous thrust burial and associated metamorphism. Slivers and sheets of Paleozoic carbonates along Mesozoic thrust faults were locally sites of syn-and post-thrust mineralization. Widespread brecciation along Tertiary detachment faults resulted in increased permeability along fault zones. Elevated thermal gradients also resulted from detachment faulting and apparently caused convective aqueous-fluid circulation along detachment faults and associated Fe+Cu±Au mineralization.

Jan 1, 1988

By AIME AIME

AN outstanding session of the Annual February Meeting was one held under the joint auspices of several groups on Tuesday afternoon, Feb. 22, as a symposium on the question of preserving peace in the postwar era through the control of the supply of sundry minerals vital to the Axis nations. D. H. McLaughlin and R. C. Allen were associate chairmen. And C.K. Leith led the discussion.

Jan 1, 1944

By Hamid Maleki

Mine seismicity is influenced by the mechanical properties of both near-seam rocks and overburden and the prudent selection of mining methods and mine layout designs. Using finite-difference modeling, experience in many U.S. mines and measurements of the pressure arch width, the author has reviewed the engineering design factors that control seismicity in room-and-pillar retreat operations for stiff stratigraphic conditions in deep western U.S. mines. By back analyzing the overburden response in now understood to have been inadequately designed historic room-and-pillar mine, the overburden collapse mechanism is addressed as well as the need for improvements in designs including panel and barrier pillar widths, and sequence of retreat.

Jan 1, 2009

By Masayasu Kawahara, Toshiyuki Kozuka

"Lorentz force, which has the functions of wave suppression and mixing control, is very useful for many metallurgical processes. In this paper, it is found that vertical Lorentz force which can change 'the gravitational force is able to modify the dispersion relation of the surface wave generated by gravity and also modify the instability phenomena on the interface so that the lower layer can be scattered into upper layers to realize the strongly mixed region.IntroductionIn metallurgical industries, recently, a new direction of process developments is required backed not only by severer operating conditions, e.g. small amount production, rapid refining, etc. but also by environment and energy problem. Because almost technologies in conventional processes have saturated, an innovative process, which can break the limits in the conventional processes, is now strongly required. Especially, controlling of mixing phenomena between two liquid phases is considered to be one of the most important technologies for the promotion of slagrnetal reaction, wave suppression, etc. On the other hand, electromagnetic forces which have various functions have been applied to many processes. And Lorentz force is able not only to suppress the wave motion of molten _metal surface but also to promote the mixing or separation of two liquids. In this paper, new controlling methods of mixing phenomena between two liquids are proposed, where a direct electric current and a stationary magnetic field are utilized. Vertical Lorentz force due to the interaction between the electric current and the magnetic field can modify the gravity force so that the dispersion relation of surface wave and the instability on the interface can be change to improve or develop the innovative processes(l,2).In case that a direct electric current is imposed on two liquid layers with a stationary magnetic field, Lorentz force of each layer becomes different due to the difference of electrical conductivity. If Lorentz force acting on the lower layer is stronger than that on the upper layer, resonance frequency of the wave motion on the interface due to the gravity can be shifted from the frequency of a outer disturbance to suppress the wave motion. And also, the lower layer can be scattered into the upper layer as liquid particles by an instability phenomenon."

Jan 1, 2000

By Arol, A. I., I. Iwasaki

The presence of calcium ion in iron ore pulps causes heterocoagulation of rnontmorillonite on hematite leading to indiscriminate dispersion. Two methods were investigated to control the adverse effect of montmorillonite: a chemical method using such complexing agents as EDTA and sodium tripoly- phosphate, and a mechanical method involving ultra- sonic treatment. Their roles in controlling the adverse effect were investigated by zeta potential measurements, starch adsorption tests, and flocculation and selective flocculation tests.

Jan 1, 1988

By I. Iwasaki

The presence of calcium ion in iron ore pulps causes heterocoagulation of montmrillonite on hematite leading to indiscriminate dispersion. Two methods were investigated to control the adverse effect of montmorillonite: chemical method using such complexing agents as EDTA and sodium tripolyphosphate, and mechanical method involving ultrasonic treatment. Their roles in controlling the adverse effect were investigated by zeta potential measurements, starch adsorption tests, and flocculation and selective flocculation tests.

Jan 1, 1986

By John L. Schroder, Woods G. Talman

EXPERIENCE has shown that certain known natural conditions and other indefinite characteristics combine to make a mining area vulnerable to mountain bumps. Some of the known conditions are heavy overburden, an overlying stratum of strong non-elastic rock, a structurally strong coal seam that does not crush easily and yet is the weakest stratum in the series, and a floor stratum of more than ordinary firmness. The indefinite characteristics could include resistance of top or bottom of a coal seam to lateral flow, effect of immediate top and bottom strata, nature of the coal seam, and other factors about which very little is known. It is in this area that exhaustive study is needed to achieve positive control of the dreaded mountain bump hazard.

Jan 8, 1958

By M A. Faizulin, N G. Stukalova

The present till now practice of averaging of ore by metal content at mining-dressing enterprises does not allow evaluating objectively really existing regularities of dressing process. The processing of large statistical data by specially designed methods has revealed the relationships of extracted mass of metals into concentrates when processing of ore at preparation plants. The analysis of the obtained relationships points to necessity of timely control by flows of ore with due account of different sorts of metal. For this problem solving it is offered to use specially designed methods on carrying out of calendar planning of a mining and shipment of ore at open casts, based on ranked arriving of flows of different sorts ores to preparation plant. The given methods includes economic-mathematical model forming and its implementing by worked out method. The formed model allows taking into account different technological and organisation limits, typical operation conditions of open cast and preparation plants. Using this methods of control of mining operations and designed on its basis the complex of software allows increasing volume of metals, extracting into concentrate, up to two per cent without any additional costs and saving of the existing technological schemes at preparation plant.

Jan 1, 2003

By J. P. Ramsey

This is a description of the efforts of a research project intended to demonstrate methods of alleviating pollution from coal mine refuse piles and slurry lagoons. These are mainly derelict barren sites. Some are burning and some are vulnerable to wind erosion which causes air pollution. Some occupy valuable land near metropolitan areas. They are an integral part of the landscape of the Appalachian and Midwestern Coal Fields. They are important in the light of growing civic awareness of the great general problem of waste disposal and environmental improvement. In the V-shaped valleys of the Pocahontas Region, they continue to be piled higher and higher. In flatter topography, they tend to form broad, flat ridges. Some contain more metal forms than others and some have a minimum of metal, but weather to a fine talc, which chokes streams with a fine particle suspension. Most are burning or have burned, but burning or weathering, most all are sources of pollution to the atmosphere and to adjacent waterways. This demonstration project is being carried out at an abandoned mine near the town of Du Quoin in southern Illinois. It is jointly sponsored by the Truax-Traer Division of Consolidation Coal Company and by the Federal Water Pollution Control Administration of the Department of the Interior. The site area is a refuse pile and slurry lagoon, each of fifty acres. It is hoped that basic data from this study will be generally applicable to other sites and will provide a basis for rational and efficient engineering design of future reclamation projects. Most refuse piles have extremely long term capabilities to produce highly potent acidogenic oxidation products typifying the more serious aspects of acid mine drainage contamination. Numerous sites remain where the abandoned mine no longer discharges acid waters, but its associated refuse pile continues to generate significant quantities of acid and other oxidation products even after many years.

Jan 1, 1969

By Ernest F. Giovannitti

A couple of years ago, one of the major television networks produced a series on the environment. One episode in the series dealt with the nation's solid waste problem and some of the research being done to solve it. It was interesting to listen to one researcher who was attempting to develop a glass that when broken would dissolve in water. It was said that using this glass would eliminate over 100 million tons of solid wastes each year. At first glance, it would appear that this research-effort would make a significant contribution to environmental pollution control; however, if one pauses to consider the water, he can see that this solution to the solid waste problem may well contribute to a water pollution problem. The dissolved material must either end up in our surface streams or be removed in waste treatment systems. Either alternative may have a more adverse effect on the environment than the original problem. With today's emphasis on the environment, it is important that the effects of our activities be studied in depth. Then, by properly planning the activity, the adverse effects can be minimized. The coal mining industry 100 years ago was in the same boat, as our glass maker, is today. Unfortunately, it too failed to consider all the effects of its activities and as a result, in Pennsylvania, there are over 5000 miles of streams adversely affected by coal mine drainage. The situation is improving, however, because mine operators are beginning to recognize and accept the methods for controlling coal mine drainage. The purpose of this paper is to discuss the measures for the control of coal mine drainage and to set forth the factors that affect these controls.

Jan 1, 1972

By Akira Yazawa

To realize highly efficient process in extractive metallurgy, continuous operation nearly in equilibrium is preferable, but most metallurgical processes consist of plural steps with different chemical potentials. Traditional two-step process of sintering followed by reduction is continuous in each step, but is heterogeneous reaction system far from equilibrium, and the chemical potentials are varied considerably along the distance the charge travels in a reactor. This route will become old-fasioned in next century due to the various inherent problems caused especially by sintering process. To establish reasonable new smelting processes, the important tasks of the metallurgists are how to introduce feed and reacting gas in the reactor, and also how to overcome the difference in chemical potential in the reactor system. Based on the ways to solve theses tasks, recent proposals of new smelting process for copper and lead are classified and discussed with the help of sulfur-oxygen potential diagram. On such potential diagram, each equilibrium step in continuous smelting is expressed at a fixed point, and two reactors with different chemical potentials must be connected by continuous molten flow through launder or partition wall. In the latter case, the reactor is apparently single, but some technical problems must be overcome. While, in a batch smelting like converter, potential variation is successively realized along a path on chemical potential diagram with the time elapsed. To establish immediate equilibrium, continuous steady flow of reactants into well mixed reactor is indispensable. In modern smelting process, the ore is mostly supplied in the form of powder which have huge surface area and fluid character, and consequently injection process must be very attractive. Several examples are discussed for both of copper and lead smelting, and promising future technologies are suggested.

Jan 1, 1988

By Shrivastava P, Humphreys M, Guibal D, Deraisme J

Customer requirements concerning the final products of iron mines are extremely stringent. Because of this, there is an ever-increasing need for mine operators to monitor and strictly control the quality of their product. This quality, as measured by the stockpile grade variability, is the result of a very complex process, where natural characteristics (the orebody and its geology) are transformed through the mining technique (open pit, shovel and truck fleet, blending into stockpile). The only way to reproduce and hence to control the variability of such a system, which is composed of several interactive sub-processes, is by simulation. A complete simulation of a Hamersley Iron Pty Ltd (HI) ore deposit has been undertaken to forecast the impact and cost of various mining methods, mining schedules and product stockpile sizes on variability of chemical and physical characteristics of the products. The mining simulation was made on a conditionally simulated orebody. On a range of criteria, the simulation was considered to fulfil the objectives set and was a valuable aid to analysis of product grade variability, operating and capital costs, selection of equipment, mine scheduling and setting of product grade targets.

Jan 1, 1994

By John C. Franklin

INTRODUCTION Alpha-emitting radon daughter products are a recognized health hazard contributing to the development of lung cancer in persons exposed to excessive concentrations over an extended period. The primary control technique used by the mining industry is dilution with fresh air. Because the uranium is deposited in porous sandstone in most U.S. mines, the control of this hazard with dilution requires excessive volumes of air. As the mines become larger and deeper, the cost for ventilation becomes a major expenditure for the mining industry Most mines are maintaining levels of radon daughters lower than required by law but to maintain these present levels the mining companies are going to be drilling more vent holes or using other control techniques as the mine expands. These control techniques are being investigated by the U.S. Bureau of Mines to determine their effectiveness, cost, and safety for underground use. [Instrumentation] The Bureau's early research used batch sampling of both radon and radon daughters for determining the concentrations. In both cases it was determined that batch sampling did not give a complete understanding of what was happening to the concentrations. Therefore, continuous monitoring systems were developed for both. A continuous flow-through radon monitor was developed by the Bureau (Franklin, et al.., 1976) using a modified Lucas flask mounted on a photo-multiplier-tube (PMT). The air was filtered twice prior to entering the flask to remove dust, diesel smoke, moisture, and radon daughters. The signal from the PMT was then inverted, shaped, and driven to a data acquisition system (DAS) which accumulated the signals. The DAS has two comparators for setting the scan time and interval, a 24-hour clock with Julian date, a printer, and a perforated paper tape punch. Sampling time is determined by the type of experiment being conducted. Our normal sampling time is one 10-minute scan every 15 minutes, but could be set as low as one scan every minute or as long as a 16-minute scan every 167 minutes. There are two models of the DAS. One is a 10-channel system and the other a 30-channel system. On a 10channel system normally 6 channels are used for radon and radon daughters and the other four channels are used for temperature, absolute pressure, air velocity, and relative humidity as described by McVey (1977). Figure 1 shows a scan of five channels monitoring the radon concentration from intake to exhaust in a stope for a non-work day. If the radon concentration stayed this constant during work days, then continuous monitoring would not be necessary. [ ] Droullard (1977) developed a continuous alpha-beta monitor. This monitor has been modified so that it can be used with the DAS previously mentioned. Control Techniques The U.S. Bureau of Mines has conducted research in controlling airborne radon/radon daughter for 10 years. Major efforts have been conducted in sealing the rock to prevent the release of radon, bulkheading to seal nonproductive areas, backfilling with classified mill tailings, and positive pressure ventilation. Also, tests have been conducted to determine the mining cycles contribution to the radon problem. Surveys One stope with two intakes and one exhaust was continuously monitored to determine the effects of blasting, mucking, and drilling on the airborne radon concentrations (Franklin, et al., 1976). Two other detectors were located inside the stope which were close to the mining activity. In this stope no appreciable change in radon was observed during drilling holes for blasting and roofbolts. This study showed increases up to 40 percent in radon for slushing in the exhaust drift. The radon remained high and very eratic during slushing, as can

Jan 1, 1981