Search Documents

By Michal Stepien, Piotr Palimaka, Stanislaw Pietrzyk

During the steel scrap melting process in an electric arc furnaces, the generated dust may contain a significant amount of zinc. The content of zinc in case of melting galvanized steel scrap is variable and ranges from 15 to 40 wt%. This dust cannot be re-used for the steelmaking process. On the other hand the zinc content is too low to treat the steel dust as a feedstock in pyrometallurgy of zinc. When they are disposed in land fills they have adversely effect the environment. This work presents selected results of research and development of new technology, which was developed in order to utilization steelmaking dust in the sintering process. One of the products (zinc-rich) can be used as a high-quality raw material for production of zinc by pyro- or hydrometallurgical processes. The second one product from the shaft furnace can be used as a feedstock for the steelmaking process.

Mar 1, 2017

By Xiao Hong, Zhang Wenqiang, Gao Bing

The characteristics of top charging coke (coke 1) and stamp charging coke (coke2) were investigated. The weight loss ratios of two kinds of cokes with and without alkalis were measured after reacting with CO under the temperature of 2 900, 1000, 1100 and 1200 °C respectively. The microstructures of original cokes were observed by SEM. The experiment results show that, with no addition of alkali, the weight loss ratios of coke 1 and coke 2 were nearly the same under the temperature of 900 and 1000 °C. While the weight loss ratio of coke 2 was much larger than coke 1 under the temperature of 1200 °C. With alkali-rich, the weight loss ratio of the two cokes was almost the same at 1100–1200 °C.

Mar 1, 2017

By Zhengde Pang, Xue-wei Lv, Guibao Qiu, Chenguang Bai, Zhiming Yan

As a result of the consumption and the rising cost of raw materials for ironmaking, steel producers have increased their utilization of low-cost, low-grade raw materials such as high alumina iron ore. The effect of Al2O3 and the Al2O3/SiO2 ratio on the viscosity, surface tension and sulfide capacity of the CaO–SiO2–Al2O3–MgO–TiO2 blast furnace slag system were studied in the present work. At a fixed CaO/SiO2 ratio of 1.20, 9 mass pct MgO, and 1 mass pct TiO2, the viscosity increases with an increase in Al2O3 content at a range of 16–24 mass pct, and decreases when the Al2O3 is higher than 24 mass pct. Increasing Al2O3/SiO2 from 0.47 to 0.92 causes a slight decrease in viscosity of the slags and has an opposite effect when Al 2O3/SiO2 is more than 0.92. The surface tension increases with increasing Al2O3 content at a fixed Al2O3 content and Al2O3/SiO2 at a fixed CaO content. The desulfurizing capacity decreases with increasing of Al2O3 content, while increases with increasing Al2O3/SiO2 at a fixed CaO content.

Mar 1, 2018

By T. Iriyama, Y. Fujita, R. Omatsuzawa, T. Nishio, N. Okochi

Sm-Fe-N hard magnetic materials are good candidates for high performance bonded magnets. Rapid-quenching method should be highly favorable for the fabrication of isotropic magnet powder with high coercivity. We report here the magnetic properties of Sm-Fe-N powders produced by a few kinds of rapid-quenching processes. Sm2Fe17 powders were prepared by gas-atomization (GA), rotating-disk atomization (RDA), or melt-spinning (MS) method. The Sm2Fe17 GA powder had dendritic solidification structure, while the RDA powder had micro crystalline structure with size of 3-5 µm. Coercivities (HcI) of their nitrides were 56 (for GA) and 217 ka/m (for RDA). The H cI of nitrided Sm2Fe17 MS powder with wheel velocity (V5) of 5-20 m/s, which had also microcrystalline structure, was 53 to 509 Wm. These coercivity values are not sufficient for bonded magnet applications. From the study of additive effects, it was found that C, C-Si, C-Ga, or C-Al addition decreased the crystal size of quenched Sm2Fe17 powder. Consequently, high coercivity was obtained; the HcI of nitrided Sm2Fe1C1Si1 MS powder with V5 of 10 m/s was 898 kA/m, and 708 kA/m for the nitrided Sm2Fe15C1Si1 RDA powder. The compression-molded bonded magnet made from Sm2Fe18Si0.1Nx MS powder showed a high (BH)max of 82.7 kJ/m3.

Jan 1, 2000

By Yuanbo Zhang, Bingbing Liu, Zhuyin Chen, Xiao Kang, Chen Liu

Composite agglomeration process (CAP) is an effective method to utilize the iron-bearing dusts generated in the ironmaking plants, by which the dust percentage in the sinter feed can be increased up to 20 wt %. In the current study, a comparison on behavior of iron-bearing dust in the conventional sintering process (CSP) and CAP was characterized. The results showed, in the CSP products, the scattered iron-bearing dust in the mixture was disadvantageous for the sintering indexes and consolidation of the finished sinters. In the CAP products, the main phase in the iron-bearing dust pellets was well-crystallized Fe2O3 grain particles. In the matrix parts, there were more Fe3O4 particles generated, which caused to high RDI+3.15 and low RI of the finished products. The pellets and the matrix parts were bonded by iron oxides and acicular calcium ferrite.

Jan 1, 2016

By Kumar M. Lyer

Residence time distribution (RTD) of light and heavy liquids in a pyrometallurgical channel reactor was mathematically modeled by representing the reactor as a combination of ideal reactors. Cold model studies simulated the counter-current flow of slag and matte (or metal) with high-strength bottom gas injection. The experimental variables include flow rates, heights, density and viscosity of the two liquids; gas flow rate; injector diameter; and distance between injectors. The experiments covered a wide range, of the appropriate dimensionless parameter, including conditions in ferrous and nonferrous extractive metallurgy. Dispersion modeling studies were also carried out to determine the degree of backmixing. Results indicate that the degree of backmixing in the channel reactor for various operating conditions corresponds to that for 3-20 perfectly mixed reactors in series.

Jan 1, 1993

By Shilai Yuan, Huimin Lu, Panpan Wang

A big andalusite ore bed was found in Dingxi District, Gansu, China. In this paper, the feasibility of producing solar grade silicon from aluminum-silicon alloys by carbothermal reduction of andalusite ore was studied. First, the carbothermal reduction experiments were conducted in a 100 kVA DC submerged arc furnace with reducing temperature 2000–2200 °C and reducing time 4 h, the hypereutectic aluminum-silicon alloys containing 50–55 mass% aluminum and 35–45 mass% silicon were obtained; then the investigation on solidification of the hypereutectic Al-Si melts under the temperature gradient as an intensified separation silicon way was carried out. According to previous investigation, the optimized technical process for solar grade silicon and eutectic Al-Si alloy from andalusite ore was proposed.

Mar 1, 2017

By P. M. Tyroler

Inco operates a hydrometallurgical plant to treat the residue from the pressure carbonylation process. The main constituent in the residue is cop¬per. The residue is leached under pressure in an acid sulphate solution in two stages and the copper is recovered via electrowinning. The electrowinning tankhouse is fully integrated into the overall plant flowsheet as spent elect¬rolyte is required in upstream leaching steps. In recent years, the amount of residue had increased and copper removal capacity became the rate limiting factor for the entire plant. Consequently, a major program was undertaken to upgrade the tankhouse with regards to capacity, efficiency, cathode quality, working environment and structual integrity and appearance. This paper will describe current facilities and operation, and detail progress in our up¬grading efforts.

Jan 1, 1987

By Bin Xu, Qian Li, Xiaoliang Liu, Yongbin Yang, Hongwei Li, Tao Jiang, Yan Zhang

The direct cyanide leaching rate of gold from a gold calcine was only 71.33%, due to 19.51% of gold being encapsulated in the iron oxides. To enhance the cyanide leaching of gold, the calcine was pretreated with acid or alkali washing. The mechanisms by which acid and alkali pretreatment improve gold leaching from calcine are investigated through chemical analysis, XRD, and SEM-EDS characterization.

Mar 1, 2017

By D. H. Magoon

The zinc smelter of Cominco Ltd. at Trail, B.C. Is the largest In the western world. A total of 550.000 tonnes of concentrate are proceed at the smelter annually. Approximately 80% of the zinc concentrate is roasted and the remainder Is treated by aqueous oxidation preaaure leaching. The zinc concentrate roasting and sulphur dioxide gas processing plants have undergone many changes over the years. This paper describes the processes and equipment currently used for concentrate roasting, S02 gas cooling and cleaning, mercury removal, sulphuric acid production liquid S02 production, and tall gas S02 scrubbing. The recent Installation of an advanced process control system for the operation of these Integrated processes Is also described.

Jan 1, 1990

By A. Rios

ENAMl's Paipote Smelter commenced operations in 1951. At present, it processes 230,000 tonnes/year of green feed in a conventional smelter, which comprises one reverberatory furnace, two Hoboken, one Peirce-Smith converters and one rotary anode furnace. The feed is composed of 83% copper concentrate and 17% metallic copper precipitates, which results in a feed average grade of 32% of copper content. The final products are 75,000 tonnes/year of copper anodes and 48,000 tonnes/year of sulphuric acid. At present, the plant is undergoing a modernization to expand the smelter capacity to 300,000 tonnes/year of green feed and increase the sulphuric acid production to 100,000 tonnes/year. This will be achieved with the installation of an El Teniente Converter and an expansion in the acid plant. The work began in November 1991 and is scheduled to be in operaton by March 1993. The paper provides an overview of the modernization plans and results achieved to-date.

Jan 1, 1993

By Qingguo Xue, Jingsong Wang, Yingli Liu, Guang Wang

In the dropping zone of blast furnace (BF), primary slag absorbing ash of pulverized coal and coke become to be intermediate slag. Due to viscosity and surface tension of slag and the pore between cokes, some slag remained in coke layer and affected the permeability of blast furnace. The flow behavior of slag with different basicity (0.55–1.10) and Al/Si (0.35–0.50) were studied. Meanwhile, the viscosity and surface tension of slag were calculated. The results showed that, with the increasing basicity of slag, surface tension increased and viscosity decreased. With the Al/Si increase, surface tension and viscosity increased. The smallest pore that all slag can pass through was 4.5 mm. However, the height between slag droplets and the bottom of crucible indicated that the ability of slag to pass through pore were weakened with the increasing basicity and Al/Si. Thus, slag which absorbed ash from fuel become difficult to pass through coke layer.

Mar 1, 2017

By I. Filzwieser, S. Wallner, M. B. Hanel, A. Filzwieser

Whenever thinking about increasing tankhouse performance two major aspects has to be considered, the technological feasibility as well as the economical impact. For meeting the requirement of an increased current density leading to an increased productivity, Mettop has developed the METTOP-BRX Technology, which allows the introduction of fresh electrolyte between each pair of anode and cathode. As an example of a green field approach the installation at Xiangguang Copper Co., Ltd will be described. Since the start up in 2011, Xiangguang Copper Co., Ltd operates one of their two copper refining tankhouse with a current density of 420 A/m2 and a current efficiency above 98% in average. At Montanwerke Brixlegg Ag, as an example of a brownfield installation, the annual production could be increased by 50%. Although for many years a total of two industrial applications are in operation, the successful implementation of this technology that result in significant operational and economic advantages has not been fully accepted within the industry due to misunderstandings, incorrect interpretations and lack of awareness. It is intended with this paper to create a better understanding about the parallel flow technology and help to eliminate worries and concerns.

Mar 1, 2017

By S. Neogy, M. Gupta, D. Srivastava, V. Kain, S. Roychowdhury, R. C. Prasad, G. K. Dey

"Austenitic stainless steels are an important material of construction for Boiling Water Reactors (BWR). These stainless steels are amenable to strengthening by strain hardening. Various deformation modes at different test temperatures and strain become active. In the present investigation type 304LN stainless steel was used in the annealed and strain hardened condition. Thin foils were prepared from gauge section for transmission electron microscope (TEM) investigation after tensile testing at room temperature and at 288°C. TEM investigation reveals that twinning is the major mode of deformation for the tests done at room temperature while dislocation cross-slip is the major mode of deformation at higher temperature. Stacking faults were also observed to a limited extent. The extent of twinning was much higher for the tests done using the rolled material. The formation of martensite in the stainless steel due to straining was investigated by the analysis of selected area diffraction patterns.IntroductionAustenitic stainless steels (type 300 series) are an important material of construction in Boiling Water Reactors (BWR). These stainless steels cannot be heat treated but can be strengthened by cold working [1]. Nitrogen alloying of these stainless steels result in high strain hardening rates and higher strength without any loss in toughness [1]. Stress Corrosion Cracking (SCC) in BWR of these types of stainless steels have been attributed to surface strain hardening and strain hardening ofregions adjacent to constrained weldment [2].The test temperature [3, 4], prestrain [5] and nitrogen level [5] has been reported to affect the deformation mechanism during tensile testing. Byun et al. [3] have reported the formation of martensite, dislocations, stacking faults and twinning during tensile deformation, the extent of each depending on the test temperature. Strain localisation has been reported to occur during tensile deformation in irradiated stainless steels [ 6]. The behaviour of rolled material during tensile testing is similar to that of irradiated material to a large extent [3]. Austenitic stainless steels are low stacking fault energy (SFE) materials in which various types of microstructures have been reported to form during tensile deformation and the strain is also highly heterogeneous in nature in these stainless steels which aides SCC in BWR environment to a large extent [7]. During cold working of austenitic stainless steels second order twinning has also been reported [8]. Knowledge about the deformation mechanisms operative in the strain hardened austenitic stainless steels during tensile testing at different temperatures is essential to understand the material deformation behavior and the present study aims at enhancing the existing understanding."

Jan 1, 2011

By Xuling Chen, Yi Wang, Xiaohui Fan

"The current control method of grate-kiln iron ore oxide pellet production is lack of accuracy and normalization due to the limited detection conditions. Therefore, mathematical models of grate-kiln temperature field are presented. With calculation of gas-particle heat transfer as well as enthalpy changes of moisture evaporation and magnetite oxidation, the thermal history of pellets throughout grate-kiln process can be acquired and used for production status estimation. Taking the calculated results as well as detected data in production as inputs, process parameters such as running speed, fan opening and coal injection rate as adjusting objects, expert system for grate-kiln pellet production is outlined. And the preheating section dominated control strategy is explained. Results of production application show that the stability rate of gas temperature in gas hood of preheating section is increased from 91.0% to 94.2%, compressive strength and first grade rate of pellet are increased by 3.62% and 2.36%, respectively, while FeO content is 18.18% lower. Control guidance of this expert system can solve production anomalies effectively, stabilize grate-kiln iron ore oxide pellet production and improve pellet quality.IntroductionSteel industry in China has developed rapidly in recent years. China’s crude steel production in 2010 is nearly 627 million, which is 44.2% of the world total production. Burden with higher quality is demanded by enlargement and modernization of blast furnaces. And oxide pellet production has become a growing concern. In 2010, the total production of pellet in China is 110 million, and about 60% is produced by grate-kiln process."

Jan 1, 2012

By Bin Xu, Qian Li, Xishan Li, Yongbin Yang, Hongwei Li, Tao Jiang, Yan Zhang

The cyanide leaching rate of gold from a multi-refractory gold concentrate (18.05 g/t Au) containing 1.62% As, 20.76% S, 6.95% C and 1.31% Sb was only 1.33%. The enhancement of gold leaching was studied mainly by the pretreatment of oxidative roasting and alkaline sulfide washing. Results showed that after the two-stage roasting (i.e., I stage of 500 °C, 1 h and II stage of 700 °C, 2 h) most of sulfur (93.84%) and carbon (98.27%) were removed, but the gold leaching rate of calcine just reached 71.33% because the residual arsenic (0.63%) and antimony (1.15%) were still high. After alkaline sulfide (i.e., NaOH and Na2S) washing, the residual arsenic and antimony was further decreased to 0.21 and 0.65%, respectively. The gold leaching rate of the treated calcine by cyanidation could increase to 93.52% substantially. Also, the optimized particle size, NaCN concentration and leaching time were −0.045 mm over 85%, 0.1% and 36 h, respectively.

Mar 1, 2017

By Donghai Li, Cheng Pan, Xuewei Lv, Mei Liu, Enguang Guo

"Phosphorite is the main raw material for the production of phosphorus in chemical industry. More attentions have been drawn to the phosphorite concentrate beneficiated from low-grade phosphorite due to the decrease of high-grade phosphorite. For another, the agglomeration process is necessary for the phosphorite concentrate after beneficiation process. The mineralogy and sintering process of the phosphorite from Leshan, China were studied in this work. The result shows that the main phases in the phosphorite are fluorapatite (Ca3(P04)3F), hydroxylapatite (Cas(P04)3(0H)), quartz (Si02) and dolomite (CaMg(C03)2). The yield of the sinter increases with increasing the carbon dosage to 7%, and then decreases when it continuously increases. Similar regularities were found for the strength and the content of P20s of the sinter. The best strength of the sinter as well as its P205 content were discovered when the carbon dosage is 7%. Fluorapatite ((Ca5(P04)3)F) is the main phase in the sinter while fuggerite (Ca2MgSiz01) is the main binder phase.IntroductionPhosphorus is an important foundation industrial raw material of national defense industry, food industry and chemical industry, where it is used to produce red phosphorus, phosphonium hydroxide, phosphorus pentasulfide and phosphoric anhydride[l-2]."

Jan 1, 2013

By Ender Keskinkilic

Continuous casting of slabs is conducted with two successive steel flows: first from ladle to tundish, then from tundish to mold. There are certain process abnormalities related to ladle, tundish and mold. For example, change of submerged entry nozzle (SEN) is the one encountered during steel flow from tundish to mold. Tundish exchange is the abnormality taking place due to replacement of processed tundish with the new one at rest. Another example is the flow of steel from ladle to tundish without a ladle shroud. In this study, a statistical analysis was conducted related to the process abnormalities in slab casters of a steel plant. Slab surface defects observed in slab yard was incorporated in this analysis.

Mar 1, 2018

By Egil Aukrust

"An American Iron and Steel Institute Task Force evaluated developing direct steelmaking technology worldwide to seek a replacement for the coke-oven, blast-furnace, basic-oxygen process technology now in use. To remain internationally competitive it is essential to move away from the traditional series of batch processes towards continuous processing and the associated energy savings which are possible with high technology process control systems. The group identified in-bath smelting of iron ore pellets or fines with coal as the process most sui table for domestic raw materials (including abundant scrap) and called for research to study operation with varying degrees of preheat and prereduction of the ore by the gases generated from the coal and various degrees of combustion of these gases above the melt.A coordinated, 3-year, $27 million, direct steelmaking research program is proposed. Concurrent projects include design, construction, and experimental operation of an in-bath smelting pilot plant; modeling, simulations, and laboratory-scale experiments at universities on slag-phase and metallicphase reactions and interactions; and large-scale heat transfer and reaction rate trials. Also included are modeling studies and pilot plant trials of on-stream decarbonization and desulfurization; application of circulating fluid bed technology to fine ore reduction and hot gas cleanup; and specific heat transfer and fluid flow research projects.IntroductionThe American Iron and Steel Institute (AISI), based on the Task Force studying direct steelmaking, believes strongly that a coordinated program of research on the reduction of domestic raw materials to liquid steel should be undertaken as part of the Steel Initiative program. To specify the steelmaking process for development best suited to the American steel industry and domestic raw materials, it was important to determine the state-of-the-art of direct steelmaking worldwide, both as practiced and under development, and then, by expert analysis of the processes and their potentials, to choose the process most likely to provide a domestic competitive edge."

Jan 1, 1988

By Jinxing Ji

Several fundamental aspects related to the nickel electrowinning from chloride electrolytes have been addressed in this paper. The thermodynamic study includes the activity coefficient of the hydrogen ion and the speciation diagram of NiCI2 solutions. The activity coefficient of the hydrogen ion (YH+) was calculated and estimated experimentally using a combination glass pH electrode. It was found that YH+ was greater than one in concentrated NiCl2 solutions and increased significantly with increasing NiCl2 concentration. The speciation diagram for NiCl2 solutions was plotted with YH+ and the effect of the ionic strength on the equilibrium constants being taken into account. It was discovered that the predominant nickel species in the acidic region were Ni2+ and NiCI+ in 0.937 M NiCl2 solution at 25°C. Electrodeposition tests demonstrated that higher Nit' concentration in the electrolyte improved the current efficiency of nickel electrodeposition (CENi). The additions of H3BO3, and NH4Cl increased very little the current efficiency of nickel electrodeposition at pH 1.5 and temperature 60°C. However, the addition of sulfate decreased the current efficiency of nickel electrodeposition. Nickel electrodeposition was also found to be a steady-state process since the amount of acid added to the electrolyte at a constant pH increased linearly with time during galvanostatic electrodeposition. The cathode surface pH during nickel electrodeposition was measured using a flat-bottom combination glass pH electrode and a 500-mesh gold gauze as cathode. The cathode surface pH was found always to be higher than the pH in the bulk electrolyte, and if the current density was sufficiently large, it would eventually reach a level causing precipitation of insoluble Ni(OH)2(s) on the cathode surface. Rotating disc electrode studies revealed that the rate of nickel electrodeposition was first order with respect to the activity of nickel ion and zero order with respect to the activities of chloride and hydrogen ions. The rate of hydrogen evolution was found to be first order with respect to the activity of hydrogen ion and to be zero order with respect to the activities of nickel and chloride ions. These findings indicate that nickel deposition and hydrogen evolution proceed independently.

Jan 1, 1995