Search Documents

By P. A. Botha

Most sinter producers prefer to use a range of iron ores with the aim to optimize their sinter blends. ISCOR is however limited to the use of ore from two deposits, namely Sishen and Thabazimbi. Only sinter produced from Sishen ore is described in this report. The Sishen iron ore deposit provides high-grade hematite ore with a mean iron content of 65 per cent. Three major ore types are developed: massive, laminated and conglomeratic. The main ore mineral is hematite with minor to trace amounts of quartz, mica, phosphates and, in places, carbonates. A sinter product is characterized by its mineralogical composition and metallurgical properties. The production rate also plays an important role in the economic evaluation of sinter quality. Sinter-pot tests were conducted with varying basicities, given as the ratio of CaO to SiO:< and coke content. The results of these tests were characterized by mineralogical and metallurgical methods. Basicity of a sinter mix directly influences the mineralogical composition and metallurgical properties. The content of calcium ferrite and calcium silicate increases with increasing basicity, thereby increasing the reducibility and cold strength of the sinter product. Experiments performed during this study provided a model for the optimization of the sinter mix with respect to its mineralogical and metallurgical parameters.

Jan 1, 1991

By Jan Vrestal, Josef Tomiska, Pavel Broz

"Thermodynamic investigations on fcc solid ternary Fe-Ni-Cr alloys have been performed by means of the computer-aided Knudsen cell mass spectrometry. Ternary T.AP.-series (Thermodynamically adapted power series) are used for the algebraic representation of the thermodynamic excess properties. At 1650 K the molar excess Gibbs energy GE is negative over the whole field of stable fcc phase. The molar heat of mixing HE is exothermic in the predominant part of the fcc phase field. Only between the section with a constant ratio of mole fraction Xcr/XNi = 0.64 and the fcc phase field boundary the HE values are slightly endothermic. The results of this work can be used successfully for phase diagram calculations.IntroductionThermodynamic investigations on multicomponent alloy systems such as the Fe-Ni-Cr ternary system including the three binary boundary systems are very time-wasting and usually beset with considerable experimental difficulties. Additionally, the required experimental equipment is very expansive and the obtained results are not always satistying. Therefore it is understandable that many phase diagram calculations are based only on few experimental values of the molar excess free Gibbs energy GE. Consequently, Kundrat and Elliott [1] as well as Hillert and Qiu [2] used in their reassessments of the phase diagram of the Fe-Ni-Cr system thermodynamic data mainly assumed and/or optimized by means of various reasoning.Lee [3] reported recently, a revision of the used thermodynamic description of the Fe-Ni liquid phase is necessary to obtain a better agreement with the experimental data on the bcc/liquid or fcc/liquid tie lines and liquidus temperatures in the Fe-rich region of the Fe-Ni-Cr ternary system than in the previous assessments. This is 'in full agreement with mass spectrometric investigations of Fe-Ni alloys in the liquid and in the fcc solid phase, published earlier [4,5]. Indeed, phase diagram calculations based upon the molar excess free Gibbs energies GE obtained in these studies yield liquidus and solidus lines in excellent agreement with experimental phase diagram data [5]. Nevertheless, these experimental data have not been considered later on any more, not even in the revision by Lee [3]."

Jan 1, 1996

"Mechanical alloying (MA) synthesizing technology and thennohydrogen processing (THP) were utilized to produce nanocrystalline Ti-MMC's reinforced by TiB intermetallic compound by using TiH2-B powder mixtures. Powders MA'ed up to 8 hours were examined by X-ray diffraction and SEM study. All MA'ed powders afterwards were HIP'ed at 700, 800 and 950EC for 1 hour. Detailed XRD, SEM and TEM study of the samples were carried out to determine the structure and micrography of the Ti-TiB MMC material processed by MA+THP approach followed by HIP'ing at high temperatures.IntroductionThe fiber reinforced titanium base composites [1,2] which possess a great resistance to high temperature have been investigated. In these studies fibers of C and SiC were used as reinforcing materials. However, these fibers react with Ti-matrix at elevated temperature resulting in product formation at the interface between the matrix and the fiber. Because of the chemical reactions, strength of the product MMC material diminishes.In conventional techniques of whisker reinforced composite material production, the mixtures of matrix metal powders and dispersed fibers are consolidated by hot pressing, HIP and/or hot extrusion. These techniques, however, have some shortcomings. Hard and brittle fibers could be broken during mixing cycle of the processing. Consolidation techniques could also be the cause for fiber breakdown. Attaining of the uniform dispersion of fibers into the metal matrix is not an easy process. The chemical reactions at elevated temperature exposures in the interface between the matrix material and fiber reinforcement cause product formations leading to poor mechanical properties."

Jan 1, 1998

By Hongfa Hu, Stavros A. Argyropoulos, Stephan Ferenczy

"Physical as well as mathematical modeling was carried out to investigate the exothermic mass transfer in liquid metal systems. In these systems, the exothermicity induces unique heat, mass and momentum transfer phenomena. Moreover, these phenomena are deeply coupled and they are further complicated by the presence of a moving boundary.In the physical model used, ice cylinders were immersed into sulfuric acid solutions, because the intermixing of ice with sulfuric acid is very exothermic. In this low temperature system, velocity and temperature measurements in the sulfuric acid were made as well as measurements of the ice melting in the sulfuric acid.The mathematical model developed solved simultaneously the heat, mass and momentum equations numerically, utilizing the control-volume finite difference approach. The enthalpy method was adopted to track the moving boundary. Predictions made by the mathematical model were in close agreement with the results obtained by the physical model.The results from the mathematical model were further validated with experiments involving high temperature liquid metals. Specifically, data were obtained in an experimental setup involving (a) dipping silicon cylinders into high carbon liquid iron and (b) dipping nickel cylinders into liquid aluminum. Results from these experimental studies supported the predictions of the mathematical model."

Jan 1, 1999

By E. Oshilna

The Mitsubishi process has many advantages pertaining to economical and environmental matters. These advantages have led to the installations of the Mitsubishi process in constructing new smelters: The Mitsubishi process utilizes highly oxygen enriched blast air and uses a special lime slag in the C?furnace. These characteristics change the . distribution of Impurities from other processes which use P.S. converters, Recently an Increased amount of secondary materials which contain impurities Is being treated at Naoshima Smelter. In order to cope with an Increment of the Impurities load and maintain the cathode quality, many Improvements have been Implemented. This paper discusses the impurities behavior In the Mitsubishi process and describes the measures taken to treat an Increased ?amount of secondary materials:

Jan 1, 1998

By Eleazar Salinas R., Miguel Perez L., J. Cesar Juarez T., Martin Reyes P., Eduardo Cerecedo S., Isauro Rivera L., Francisco Patino C., Juan Hernández A.

"A complete characterization of burrows from Mining district of Pachuca - Real del Monte, in Hidalgo state Mexico, was done. These kind of residues had not been formally characterized, founding an average chemical composition of 70.43 % wt. of Si02, 7.032 % wt. of Ah03, 2.69 % wt. of Fe20 3, 0.70 % wt. of Mn, 3.98 % wt. ofK20, 3.34 % wt. of CaO, 2.50 % wt. ofNa20, 1.01 % wt. of MgO, 0.26 % wt. of Ti02, 0.04 % wt. of Zn, 0.026 % wt. of Pb, 56 g/ton of Ag and 0.6 g/ton of Au; In the same way, the residues present as majority mineralogical phases the following: Quartz, Berlinite, Orthoclase, Feldspar, Anorthoclase and Calcite. By the other hand, joint with the big volume that present these residues and the chemical and mineralogical characteristics, these materials or sub - products can be used for production of ceramics, into mixes forming some materials for architecture (bricks, blocks, and tiles), refractory bricks, in the production of cement and to get some metallic values such as gold and silver involved in these residues.IntroductionActually the mining residues in Hidalgo State, Mexico are the result of more tan 500 years of mining, leading so a great volume of deposits, which we can classify in different types, among the most communes we have: Acid Mining Waters, Waters of solid transport and elements in the form of radicals, deposits of abandoned minerals without processing, and mining wastes of processed minerals known as burrows or dumps, being these the most abundant in the Hidalgo State [1-4].Form the metallurgical point of view, it is known that a characterization study if fundamental to find the viability of reuse of these kind of residues, leading so an additional use and the opportunity of get an alternative use into several industrial processes, due to its contents of oxides of silicon, iron, aluminum, calcium, sodium and potassium, principally, besides of its mineralogy and distribution of chemical elements into its primary and secondary phases [ 1-2, 5- 6]."

Jan 1, 2011

By Bin Du

In recent years, concurrent product design and process is gaining popularity and will become a norm of the industry of the future. Forging has been a critical manufacturing process for production of components with superior tensile strength, toughness and grain flow. This paper describes an expen system which is being developed for forging die design and forging process analysis in concurrent engineering environment. Rules and guidelines pertaining to forgeability are formulated and incorporated into the knowledge-base in building the system. The system is built using an object-oriented paradigm. The object-oriented approach and hierarchical rule structure paradigm are briefly discussed. Finite element analysis packages (ALPID-2D) were incorporated into the program to give the simulation result of the forging process. The system can automatically produce a competent design and recommend a set of processing parameters for a given product. The designer can modify the design according to the result of the simulation.

Jan 1, 1992

By Ronald Erdmann

Today the BOF filter dusts and sludges are mainly dumped due to their zinc contents. By typically ranging from 2 to 5 % they prevent the filter dusts and sludges from beeing recycled via the blast furnace route. Based on the different discharge kinetics of Iron and zinc during the main blowing period In a bottom stirred BOF a simple and efficient system for recovery allow zinc fractions has been developed. The obtained material Is suitable for recycling without nsc of shell formation In the blast furnace. Different subsequent development steps have been performed. By starling with a very simple lime dependent model the sludge from the BOF off gas cleaning system was collected in two different sludge channel systems. This model based an the fact that most of the scrap based zinc Is discharged from the melt within the first eight to ten minutes of the BOF process. To Improve the system a spectroscope zinc sensor was Installed at the hot section of the off gas cleaning system to get more reliable informations on the actual zinc concentation of the BOF dust. By use of the system up to 50 % of the BOF sludge can be recycled.

Jan 1, 1995

By Kimiaki Utsunomiya, Yasumasa Hattori, Yoshiaki Mori, Toyokazu Okubo

"The effect of various operating conditions on splashing behavior in a Peirce-Smith converter has been investigated with a 1/5.7 scale cold model. Dynamic similarity between the model and a commercial converter was attained by setting the modified Froude number in the model experiments in· the range for normal converter operation. It is known that for a given modified Froude number the dimensionless penetration length of gas into the liquid phase increases as the liquid density decreases. Moreover, penetration· length has a large effect on splashing behavior. Therefore, a heavy liquid, a mixture of water and lead concentrate was used as the liquid phase. It was concluded that the amount of splash dramatically decreases with a reduction in the buoyancy energy per, unit liquid mass and an increase in the horizontal distance between the tuyere tip and the edge of the mouth.IntroductionSubmerged gas injection is widely used in practice in ferrous and nonferrous pyrometallurgical operations to achieve large gas-liquid contact areas and good agitation of liquid for rapid chemical reaction. The common application in ·nonferrous industry is the Peirce-Smith converter with multi-tuyere for copper and nickel matte converting. This process has been used for over 100 years because of its effectiveness in mixing of the molten bath, as well as its merits of the engineering simplicity. However, the mechanisms which · determine the blowing performance is poorly understood, and the design and operating conditions of the Peirce-Smith converter varies widely from plant to plant, such as by diameter, length, mouth angle, tuyere position and level of molten matte. Smelters have continuously made an effort to increase converter productivity, implying maximum tuyere blowing rate. Above a certain critical blowing rate, splash of molten matte from the converter mouth becomes unacceptable because of dangerous ejection and accretion buildup around the converter mouth, which results in interference with effective hood sealing. In fact, a 1993 converter survey[!] reported that splash was a major limiting factor for blowing rate and 54% of responding plants from around the world regard it as a limiting condition[2]. In order to increase tuyere blowing rate a study of the effect of various operating conditions on splashing behavior is expected."

Jan 1, 2000

By J. C. Huyhua

The effect or various oxidants on gold and silver dissolution in thiourea solutions (0.05 M in H2SO4) was studied using the rotating disc technique, a.t 2s c and 600 rpm. These studies were carried out at constant (4:1) initial molar ratio or thiourea to oxidant concentrations, to produce 50 % thiourea. oxidation. The initial dissolution rate of gold was approximately four times higher in the presence. of ferric sulfate (5.37 x 10-3mg cm-2 s-1) than in the presence of hydrogen peroxide (H2O2), potassium persultate (K2S2O3), or monopersulfa.te (KHS06). The dissolution rates for silver were considerably lower than gold for the same oxidants. Oxidation of thiourea in the presence of peroxygen and persulta.te compounds is a. fast reaction and it is completed in less than ten minutes. On the other hand, the oxidation or thiourea with? ferric.sulfate is slow, yielding a second-order reaction rate constant k = 6.09 I mol-1 h-1. Sulfur formation in the ferric thiourea system begins when ferric ion reduction approaches to completion. With hydrogen peroxide, sulfur is observed at lower thiourea concentration than ferric. Suifate. The presence of a large excess or free thiourea i.e., s to 20 % thiourea oxidation) retards sulfur formation and maintains favorable dissolution rates. Finally, carbon-in-leach experiments indicate that thiourea solutions a.re stable for several days, with ferric sulfate or hydrogen peroxide. The dissolution rates of gold and silver doubles in the presence or activated carbon when hydrogen peroxide is used as oxidant.

Jan 1, 1989

By E. Oshima

In May 1991, a New Mitsubishi Continuous Copper Smelter Line started operation at Naoshima. Recently, it has been continuing steady operation and one and a half year campaign life has been achieved. In 1996, new records of on line time, the amount of copper concentrate treated and copper anode production were achieved. 1t proves the superiority of the process with respect to pollution control, energy efficiency, flexibility and easiness of the operation and over all economy including off gas handling cost. Furthermore, .plans are underway to prolong the campaign life for two years and to improve the process efficiency. This paper describes recent operation, improvements, and a future capability study.

Jan 1, 1998

By G. C. Gullo, H. Wabusseg, P. J. Uggowitzer, H. Kaufmann

"The basic concept of New Rheocasting (NRC) is described and the application of wrought alloys with this process is discussed. Practical experiments with the aluminium alloy AIMgSi I are explained. For this alloy the proper NRC - casting temperature was determined by using Thermo Cale - computer software and DT A and the essential processing conditions are shown. In the experiments the melt was taken from an aluminium holding furnace and cast into NRC steel cups. After controlled cooling the resulting slurries were cast into a 4-step die on an UBE HVSC 350 Squeeze Casting machine. The characteristic microstructural values such as grain size and shape factor were measured and compared with classical casting alloys. The influence of the wall thickness of the step part (6 mm, 10 mm and 14 mm) on the microstructure is described. Tensile properties in different heat treatment states are compared with characteristic prope1ties of the same alloys in forged condition. The ew Rheocasting - process CNRC)The NRC process is a recently developed new semi-solid processing method which allows the production of pore-free, pressure tight components.In the NRC process a fu lly liquid, but only slightly superheated melt is taken from a holding furnace and poured into specially designed steel crucibles, which are placed on a carousel next to the Vertical Squeeze Casting machine. In this ,NULL,slurry maker'· globul ar a-Al grains grow, following forced homogeneous nucleation at the cup wall [ 1, 2]. In the few minutes during which the melt is cooled to sem i-so lid processing temperature, a stable ske leton of a-Al phase forms. The resulting slug keeps a cylindrical shape during its slide into the sleeve of the Vertical Squeeze Casting machine, where it is cast into shape."

Jan 1, 2000

By Philip Nash, Jie Zhou, Joshua Blackketter

"Large ingots tend to have internal defects such as shrinkage cavities and porosities, which have to be closed during the cogging stage to ensure sound internal quality of forged parts. In this work, finite element methods were used to simulate open die forging passes, with varying parameters that affect the void closure behavior profoundly. Numerical models ware constructed in ABAQUS, DEFORM and FORGE using data taken from footage of the forging process and material mechanical data obtained from the Gleeble compression tests. Forging variables such as pass rotation, reduction per pass, and feed ratio were studied with intense attention paid on the special properties of H13 steel, so that this study can be applied to solve real world problem.IntroductionCenterline defect closure is a frequently studied but still challenging topic in open die forging industry. In practice, open die forging is employed as an effective hot forming process to make desired shape of metal products as well as to ensure center consolidation of internal defects which result from the casting process. Nowadays, remarkable large forgings have been more and more required to meet industries demand. However, the increase in ingot size has tended to result in considerable macrosegregations and shrinkage cavities or voids, which need to be worked thoroughly during the forging process; but the size of the products and limitations of manufacturing capacity, such as the press load, make it difficult to achieve adequate local deformation to close those defects. Therefore, choosing optimal forging parameters under given work condition to ensure good internal quality of forged products is critically important."

Jan 1, 2012

By De-wen He

The distribution of persistent organic pollutants in the environment is studied using the multimedia environmental fugacity model, and environmental health risk assessment of POPs nearby a copper smelt enterprise is carried out. The result indicates that all are in an agreeable risk level without exception. The annual individual chronic risk index of HCB is 7.50×10-11. The annual individual risk index of 3,3&apos;,4,4&apos;-TCB is 1.57×10-9, and the annual individual risk index of 2,3,7,8-TCDD is 6.57×10-9.

Jan 1, 2009

By Geoffrey Brooks, Ben M. Ekman, M. Akbar Rhamdhani

"Concentrated solar collectors including solar simulators have been studied to concentrate solar radiation to flux levels capable of reaching temperatures of 3000K. Currently, there are no industrial scale solar reactors used for material processing and only small research units have been tried. Various laboratory scale solar reactor designs are reviewed including their operating temperature and heat transfer efficiency. Solar reactor designs can be classed into directly or indirectly irradiated and single or double cavity construction. Thermal efficiencies of up to 40% have been achieved in experimental units while operating at 1500K. Problems are encountered that relate to the transfer of high heat flux. Hybrid reactor system should be considered in the future to overcome some of the practical issues associated with solar thermal reactors.I. INTRODUCTIONIn the high temperature processing of materials, such as the production of metals, cement, refractory or glass, the reactions are typically performed in the range of 500° to 2000°C. Metals are produced from minerals, which maybe oxides, sulphides, chlorides or silicates, and to recover the metals, these compounds have to undergo chemical reaction to liberate the metal. The thermodynamic stability of these compounds found in minerals necessitates the use of high temperatures to break down the bonds between the metals and other elements. Normally, the raw metals produced from smelting require refining, which is often carried out in the molten state. As new energy sources have been established, new furnace designs have evolved to incorporate the latest technology. Although solar energy has existed longer than all the current energy sources, it has not yet been incorporated into any industrial smelting; refining or melting processes. The solar radiation reaching the earth’s atmosphere, called the “Solar Constant” (SC), is defined as the rate at which solar energy is incident on a surface normal to the sun’s rays at the outer edge of the atmosphere when the earth is at its mean distance from the sun. The currently accepted value is 1367 W/m2 [1]. The earth intercepts only a small amount of this and 30% is reflected back into space, 47% is converted to low-temperature heat and reradiated into space and 23% powers the evaporative and precipitation cycle of the biosphere [2]. As a result, the solar energy reaching the earth’s surface is weakened considerably to about 1000 W/m2 or one sun, on a clear day and much lower on cloudy or smoggy days [3]. The thermodynamic limit for solar concentration is determined from the inverse square law [4] by the factor sin2? = 46,764 sun’s [5] where ? is the angular size of the sun and equals 0.0093 radians [7]. This would produce a steady state temperature equal to that of the sun’s surface of approximately 5800oC. In practice however much lower concentrations are achieved due to geometrical and optical imperfections, shading effects and tracking inaccuracies. Optical configurations based on parabolic-shaped mirrors are commercially available for large-scale collection and concentration of solar energy for the generation of electrical power. The most common configurations used for concentration of the sun’s energy in solar thermal applications are parabolic troughs, solar towers and parabolic dishes [8,9]."

Jan 1, 2014

By W. L. Dalmijn

The processing of scrap and scrap cars starts with size reduction by a hammermill, or shredder. After the liberation the magnetic fraction is removed. The remaining non¬magnetic fraction mixed with other materials is screened and each fraction is processed separately. The increased use of plastic has a negative effect on the recovery of metals and waste production. At Huron Valley, Belleville Michigen, USA, the non-ferrous fraction from 5 million obsolete cars per year, containing 200,000 tons of non-ferrous metal, is processed. Aluminium Is recovered with a heavy medium separation process and concentrated with eddy current separators. The remaining heavy non-ferrous fraction is concentrated by a new combination of eddy current separation and image processing. After this separation process the zinc fraction is melted and refined and the copper, brass, stainless steel and other high-quality concentrates are sold to the secondary industries. The recycling of car scrap has become an important source of metals and materials for the secondary. materials processing industry.

Jan 1, 1995

By J. Y. Hwang

The relationship between coal characterization and physical cleaning has not been well understood due to the complex nature of coal. Therefore, it is difficult to apply the results of coal characterization to predict and evaluate the performance of a physical separation (e.g. flotation). Eight U.S. bituminous coals were analyzed and studied petrographically in conjunction with washability and flotation tests. The results show that grindability correlates to ash and fixed carbon contents; liberation determined directly by petrographic techniques is close to liberation determined indirectly by washability; and an ideal separation efficiency can be determined by measuring the inertinite content and the washability separation efficiency using a heavy liquid with a density of 1.4. The ideal separation efficiency was attained for most coals by packed column flotation. The ideal separation efficiency can be used for comparing process technologies and process parameters.

Jan 1, 1988

By D. Papazoglou

This work was undertaken to investigate the thermodynamic and kinetic feasibility of using hot sulfur dioxide bearing gases from smelting processes to selectively sulfate the nickel in nickel laterite ores for subsequent extraction in water. The environmental benefits ofthis approach, as opposed to releasing the gas to the atmosphere, and the economic benefit of directly utilizing the S02 rather than converting it to sulfuric acid are strong drivers for such a process. A thermodynamic analysis indicated that selective sulfation of the nickel could be feasible under appropriate conditions and these were explored through a series of laboratory scale experiments. Laterite samples were reacted at temperatures between 500 and 800°C with an equilibrated mixture of sulfur dioxide, oxygen and nitrogen in a fixed bed reactor. Tests were conducted on saprolitic ore from Bulong, Western Australia, limonitic ore from New Caledonia and garnieritic ore from Indonesia. Nickel extractions were highest from the limonite and relatively low from the other ores. The maximum selective extraction of nickel from the limonite in a single stage sulfation was 73%. Sulfation of other elements present in the laterites was also examined. A two-stage process was also identified which involved sulfation using a strong sulfation potential followed by weaker sulfation potential to attempt to convert ferric sulfate formed in the first stage to ferric oxide. This increased the extraction for the limonite ore to around 84% Ni, 95% Co and 2% Fe. Direct sulfation of laterite could be feasible in locations where sulfide smelting or roasting operations are relatively close to laterite deposits.

Jan 1, 2003

By P. A. Rusin

Many manganiferous silver deposits remain undeveloped because standard chemical extraction methods yield poor recoveries or are &apos; environmentally unacceptable. Biotreatment of such ore deposits in our laboratory resulted in manganese and silver recoveries of greater than 90%. Ore and sediment samples were collected from mining sites in Colorado and Arizona. Portions of samples were incubated in a semi-solid mineral salts medium amended with 20 mM glucose mid manganese dioxide (Mn medium). The cultures were incubated at 3(fC until manganese reduction was detected by a .color change fr:om .black to clear. Bacteria from these cultures were purified on Tryptic Soy Agar and individual isolates were retested for Mn reduction by an agar overlay method. Bacteria were identified according to Bergefs Manual ?of Systematic . Bacteriology. Most of the Mn-reducing bacteria are Bacillus species. Bacterial manganese reduction kinetic experiments were performed in 52 ml mineral salts broth supplemented with manganiferous silver ore instead of manganese dioiide. These cultures were incubated with agitation for 16 d. Aliquots were removed periodically and analyzed for solubilized manganese by atoniic absorption (AA). Cyanide (1,0 M) Vias added to the remaining ore-medium mixture for a 24 h bottle roll. The supernatant was analyzed for soluble silver by AA. Similar experiments were conducted on a larger scale using 15% pulp density. After bfotreatment of the ore, standard bottle rolls were performed. The pregnant solutions and the residues were analyzed for manganese and silver?using AA or fire assay as appropriate. In sterile. controls-which received no biotreatment, manganese and silver recoveries were 0.3% and 10% respectively; During biotreatment, total manganese solubilizatiori was as high as 99.8%. The reduced manganese could . be stripped from ?the growth medium using hydrometallurgical techniques. Silver recovery vaned from 70% to 92.5%. Microbial treatment of refractory mangairlferous ores can result in high recoveries of manganese and silver. Retention time varies depending upon the relative concentrations of manganese, silver, and other metals in the ore with only two days required in some cases, The biotreatment of ore is environmentally&apos; acceptable while the use. of chemicals such as sulfur dioxide is less so.

Jan 1, 1991

By Toshio Suzuki, Machiko Ode, Won Tae Kim, Seong Gyoon Kim

"The Ostwald ripening and growth and coarsening of the secondary dendrite arm are studied using a phase-field model. The phase-field parameters are obtained at a thin interface limit proposed by Kim et al. In Ostwald ripening analysis, the difference of the concentration due ·to· the curvature effect is shown. The third power of the average particle radius Rav is proportional to time and the ripening constant shows a good agreement with the value by Deppers et al. The particle radii distribution shows the transition behavior to attain a self-similar stationary shape. The growth and coarsening behavior of the secondary dendrite arm is also analyzed using a phase-field model. The estimated arm spacing and its dependence on time are in good agreements with experimental data.IntroductionThe ripening or coarsening process controls the microstructure during the late stage of solidification. The ripening phenomena are recognized firstly by the Ostwald [1]. The first quantitative analysis for the Ostwald ripening in the limit of vanishing solid fraction was provided by Lifshitz, Slyozov and Wagner (LSW) [2,3]. In their study, that the mean radius grows proportional to the cubic root of time and the size distribution of precipitations shows a ""self-similar"" shape are shown. Most of the studies for the Ostwald ripening confirm or predict these two general rules above. In case of finite solid fraction, the general rules are observed but the ripening constant is larger and the self-similar shape is wider than the LSW prediction respectively [4-6]. To analyze· the high solid fraction system, the theories that consider the solute field correlation are proposed [4,7-8]. In the theory, however, since the particle is treated as the point, the effect of the concentration field deviation from the monopole field should be taken into account. Recently the numerical simulation, in which not only diffusive transportation of solute but also convection effect is considered, has been done using a phase-field model [9]."

Jan 1, 2000