Search Documents

By W. F. Ranson, R. C. Progelhof

"I. THE PROBLEM: MANUFACTURING PRODUCTIVITYThe 1985 President's Commission [I] on Industrial Competitiveness found compelling evidence of the declining economic position of the United States in world markets. The annual rate of increase in the United States productivity is approximately one-seventh that of our major trading partners over the last decade: profit levels in manufacturing investments are below those of the mid-1960's; an increasingly negative trade balance since 1971; and a sharp decline in the United States share of world trade in manufactured goods for more than two decades. A particularly dramatic example of the shifting economic balance is the fact that Japanese productivity growth has been five times greater than that of this country since 1960. In face, Japan's productivity now exceeds that of the United States in such critical industries as steel, transportation equipment, electronics and electrical machinery.American employees have experienced the competitive consequences of this nation's lagging industrial performance. Between 1980 and 1984 alone, the population of non-farm employees engaged in manufacturing dropped from 22.4% to 20.6%. This reduction in manufacturing must be arrested.Commissions RecommendationsThe comprehensive set of recommendations offered by the President's Commission recognized the nation's ""key competitive advantages"", technology and human resources, and calls for their strengthening. Particular emphasis is placed on manufacturing technology and the fact that this country does not translate research into new technologies rapidly and fully.""Perhaps the most glaring deficiency in America's technological capabilities has been our failure to devote enough attention to manufacturing or 'process' technology. It does us little good to design state-of-the-art products if within a short time our foreign competitors can manufacture them more cheaply. The United States has failed to apply its own technologies to manufacturing. Robotics automation and statistical quality control were all first developed in the United States but in recent years they have been more effectively applied elsewhere""."

Jan 1, 1988

By Hector M. Henao

In order to provide the thermochemical data regarding the slag system, which are of importance for sulfide smelting and metallurgical processes but still lacking, an experimental study was carried out on the phase relations and activity of iron oxide in the FeOX-CaO-SiO2 system at temperatures between 1300 and 1400 °C and partial pressures of oxygen between 10-9 and 10-4atm. First, the solubility of CaO and SiO2 in the solid FeO were obtained and the tie lines connecting between the solid wustite (FeO) or magnetite (Fe3O4) phase and the liquid phase were determined. Secondly, iso-activity lines for FeO in the homogeneous liquid region were determined, based on the activity of iron in the Pt-crucible used in the equilibrium experiments. The activity coefficient of FeO in this region was also derived from the composition of FeO and FeO1.5 in the liquid region. Finally, the effect of (CaO/SiO2) ratio in the system and partial pressure of oxygen on these thermochemical quantities is discussed.

Jan 1, 2006

By Toshihide Takenaka, Takashi Matsui, Nao Murakami, Masahiro Kawakami

"Electrowinning of Ti have been investigated in a LiF-NaF-KF melt including K2TiF6 at 773-923K by applying electrochemical oxidation ofH2 gas as an anodic reaction. The cathodic behavior of titanium and the anodic behavior of H2 gas were studied by voltammetry in detail to clarify the electrolytic condition for the process. The electrowinning of Ti was carried out by potentiostatic _electrolysis. Steady electrolysis was achieved under the suitable electrolytic condition without breaking out the anode effect. Titanium metal was electrodeposited on a Ti cathode though the deposits were usually powdery. It is concluded that this process is potential if the morphology of the deposit can be improved.IntroductionTitanium has such good properties as high specific strength and high corrosion resistance. However, the availability of Ti has been limited because the price of Ti is much higher than those of other common metals, such as Fe and Al. The production process of Ti ingot from its ore is rather intricate so that the production cost is high. If the simpler process is developed, the production cost should be retrenched. Titanium metal is usually produced by the Kroll process, which consists of the electrowinning of Mg metal in molten salt and the chemical reduction of TiCl.i by Mg metal. The Kroll process is very elabrate, but not simple. Because the chemical reduction ofTiCl4 by Mg metal is highly exothermic, a considerable amount of energy is wasted.Titanium metal can be electrowon in molten salt bath in principle. A simpler and more effective process than the Kroll process may be realized by the direct electrowinning so that the electrowinning of Ti metal has been studied widely[ 1]. Some researchs progressed to a pilot plant stages [2], but the electrowinning of Ti has not been industrialized yet."

Jan 1, 2000

By A. M. Alfantazi, M. Boissoneault, D. B. Dreisinger, J. Synnott

"The effects of five commercially available foaming reagents (range of 0 to 25 ppm) namely Dowfroth 250, Saponin, Yucca, Licorice and Meta-Para Cresol on acid mist control, current efficiency, polarization behavior, and deposit morphology and orientation were investigated. The deposition was carried out using a bench scale electrolysis apparatus (cell volume 3L) at 500 Nm-2 and 38°C for 3 hours from Kidd Creek zinc electrolyte. The acid mist control capability of the various reagents was studied and compared by characterizing the foam layer generated during actual electrowinning conditions and by direct quantitative measurements of acid mist levels on top of the electrowinning cells. Within the range considered, the addition of these reagents reduced the current efficiency, refined the grain size of the deposit, and changed to preferred orientation of most of the deposits. Among the reagents tested, acid mist measurements indicated that Licorice and Dowfroth 250 were the best acid mist suppressant at emissions of 0.30 mglm3 and 031 mg/m3 respectively while Yucca and MPC produced the most mist at 3.0 mg/m3 and 33 mg/m3 emission rates, respectively.IntroductionMost of the world's primary zinc is produced via a combined roast-Ieach-purificationelectrowinning process. Depending on the electrolysis conditions, several additives may be added to the electrolyte. Some (e.g. glue, antimony, sodium carbonate) are added to mainly counteract the detrimental effects caused by impurities while others (e.g. licorice, Saponin) are used as foaming reagents to prevent excessive acid mist formation. Acid mist emission is a problem in many electrolysis operations because it corrodes the equipment and is a health hazard to the workers in the tankhouse as well as it pollutes the environment. Due to recent trends towards more environmental protection and more stringent in-plant hygiene, there is an increasing need to minimize these aerosols. In order to eliminate or minimize these aerosols foaming agents are usually added to the electrolyte to produce a foam layer on top of the electrolyte, thus trapping most of the mist. The ideal foaming agent would trap all of the mist and would not interfere with the electrowinning process. It is also evident that the reagent toxicology, cost and availability are important factors that need to be considered.Review of the available literature clearly indicated that very little work has been done in the past on the subject of acid mist control in electrowinning operations particularly in the area of foaming and anti-misting properties of surfactants. Two papers [1,2] have reviewed briefly the existing technologies for acid mist control. Recently, most of the work in this area has focused on the development of special mechanical devices that could be attached to the electrodes and control the mist generation at the source before it is emitted to the cellhouse [2-5]. On the other hand, extensive body of literature exists that deals with the effects of anti-misting reagents on the electrowinning aspects [6-7]."

Jan 1, 1997

By Mingmei Zhu, Xin Qiu, Xiaofei Dou, Yu Wang, Tiancheng Lin, Bing Xie

In this study, the slag forming route of the single-slag steel melting when smelting medium phosphorus hot metal was investigated. The CaO-SiO2-FeO-MgO-MnO-P2O5 as hexahydric slag system was adopted in the converter. The effect of slag composition on liquidus was calculated by FactSage, the isogram of phosphorus distribution ratio was calculated by using the regular ion solution model, combining these two tasks, the theoretical slag forming route was obtained. Through experiments, the actual melting point ofthe corresponding components on theoretical slag forming route was obtained, in this way, the theoretical slag forming route was confirmed. Then, the theoretical slag forming route was applied to industrial test in a 210t BOF. After using the new slag formating route, the dephosphorization ratio was increased 3.6% while the auxiliary materials consumption was reduced, and the cost of steelmaking was reduced.

Jan 1, 2015

By C. M. Diaz

The chemistry of the main unit processes in nickel extractive pyrometallurgy is reviewed. Key re1a ions between smelter feed composition and process selection are discussed, with particular reference to operating conditions, energy requirements and products. The paper a1 so includes a brief discussion of current nickel smelters, based on the results of a recent survey carried out by TMS.

Jan 1, 1988

By Lijun Liu, Yingwei Li, Jianhua Liu, Jinhui Peng

"As essential equipment in the metallurgical industry, current air heat exchangers cannot meet the requirements of high temperature heat transfer. In this paper, an energy efficient air heat exchanger, based on accumulation of the heat generated by microwave absorbing materials, is presented according to heat transfer theory and principles of the microwave field. A tubular shaped heat exchanger was designed and built up through temperature-rising curve, and experimental research of microwave high-temperature air heat exchangers was carried out. It was found from experiments that the tubular shaped heat exchanger fabricated using material B could be used for high temperature heat transfer system, and equilibrium temperatures could reach up to 457—485?.IntroductionHeating or cooling of air by heat exchangers is commonly practiced in a wide range of industries including construction, chemical, machinery, textile, printing, and dyeing [1-3]. Generally such heating or cooling of air is achieved in pipe heat exchangers. There are several drawbacks for such heat exchangers, namely, (i) the limitation of temperature to which the pipes can be heated, (ii) tendency to oxidize at high temperature, and (iii) poor strength of metallic pipes at high temperature. These limitations do not allow pipe heat exchangers to be operated at high temperatures [4-6].Microwave heating of inert solids, which are stable at high temperature, is a possible solution to achieve high temperature of the medium in air heat exchangers. It is well-known that microwave heating is an efficient, clean, safe, easy-to-control heating method. Microwave heating utilizes the dielectric and magnetic properties of a material. When microwaves penetrate and spread into the dielectric material, electrons, ions, etc move in the internal electromagnetic field, while the elasticity of inertia and friction impede these movements. This results in a significant thermal effect, increasing the surface temperature rapidly [7-8]. This paper studies mainly design and experimental research of microwave high-temperature air heat exchanger."

Jan 1, 2011

By H. Fukushima, T. Ohgai, N. Baba

The electrodeposition behavior of Zn and the morphology of the deposited Zn were studied in electrowinning solutions containing polymer additives such as gelatin and polyethylene glycol (PEG). The cathode potential was shifted in a less noble direction and the polarization resistance for Zn deposition increased with increasing concentrations and molecular weights of both gelatin and PEG added to the electrolytic solutions. However, when the molecular weights of these additives exceeded about lxlO4, the cathode was depolarized and the polarization resistance for Zn deposition decreased with increasing molecular weight. The crystal grain size and the (002) orientation of the deposited Zn became smaller when the concentration and molecular weight of the additives increased, and the cathode was polarized.

Jan 1, 2000

By Zviad Kovziridze

It is stated that the specific character of SPHTS specimens of TiCx consists in crystal lattice strength reflecting the condition of synthesis in ?burning wave?. The use of roentgenographic and other methods of analysis allow to estimate the effect of the conditions of synthesis causing the carbon sablattice defect on the grinding intensity of TiCx -phases. The study of the kinetics of vibratory grinding of TiCx -phases in ethanol and benzene medium allows to establish high grinding intensity of the phases close to stoichiometry and the possibility of producing high dispersion powders (Ssp 4.5-6 m2/g).

Jan 1, 2006

By Ping Long, Bin Yang, Jian Wu, Xiumin Chen, Wenli Zhang

In this study, the analysis method of trace element in pure indium using glow discharge mass spectrometry (GD-MS) has been established by correcting the analysis result, which was obtained from non-standard quantitative method of GD-MS. The effect of instrument operating parameters, the resolution and isotopes and the pre-sputtering time on the determination results were investigated respectively. The optimized operating parameters of the instrument were obtained as follows: the discharge current was 37.5mA and discharge airflow was 475ml/min. Mass spectral interferences have been eliminated using selected resolution and isotope. The pre-sputtering time was 30 min. 4 trace elements in two pure samples were determined for 6 times. The RSD were less than 20%. The content of trace elements in indium samples was determined by GD-MS and Chemical Analysis Method of Indium which is tested by inductively coupled plasma atomic emission spectrometry, respectively. The results were consistent with each other.

Jan 1, 2016

By Mônica Suede Santos Silva

This work describes characterization of the performance of the tundish of a six strand continuous casting unit of the Companhia Siderurgica Belgo Mineira, Joao Monlevade, Brazil using physical modeling. Permanent and transient conditions, due to ladle metal composition changes are considered. Pulse and step tracer addition techniques are employed to assess the control variables. For transient conditions the degree of inter-mixing and the minimum residence time are determined with a view to optimize the process especially during the grade changes of steel.

Jan 1, 2003

By Akira Yazawa

The continuous converting has attractive advantages, but further experimental studies on the slag are required, when the process is considered thermodynamically. The summarized experimental results, obtained with iron silicate slag and with ferrite slag and results relating to actual operation are described and discussed in this paper. At first, equilibrium relations at controlled oxygen potentials among three melts of silica-saturated iron silicate slag, white metal and copper are investigated. The results obtained for slag agreed with the thermo-dynamical predictions. Namely, to suppress a magnetite separation, the system should be at high temperature; in the case of the S02 gas of 10 kPa, for example, magnetite did not separate from the slag at 1300°C, but at 1250 and 1200°C the slag was saturated with magnetite even at lower SO2 pressure. Copper losses caused by dissolution of its oxide increased with increasing 5O2 pressure, and were slightly lower than those reported in previous papers without the matte phase. When the continuous converting slag does not contain any appreciable amount of silica - in contrast to the conventional smelting slag ferrite slag would form, but there was no published fundamental work on-ferrite slags. Hence, the melting behavior and activities of the system CaO-Cu2O-Fe2O3 have been investigated. The liquidus diagram in nitrogen atmosphere was, constructed using both thermal analysis and quenching method. The low liquidus temperature region without magnetite separation was found in the part of low content of Cu2O in the section Cu2O-CaO-Fe2O3 and Cu2O?Fe2O3¬CaO?Fe2O3. The activity of Cu2O in the system was also measured. Slags, composed-of CaO, Cu2O and Fe2O3, in platinum crucibles were equilibrated at 1250°C and controlled oxygen pressures. After quenching, the-composition of slag and platinum crucible were determined qualitatively. On the thermo-dynamic analysis of the results, iso-activity lines were drawn, and it was shown that the slag in the converting furnace of the Mitsubishi process exists in an adequate region of the composition triangle.

Jan 1, 1976

By Jefferson Caponero

The tire is an expressive component of Municipal Solid Waste, manly when its occupied volume is considered. Its treatment by pyrolysis stands for a list of advantages, such as: landfill releasing and a production of a high quality fuel. The exploitation of new natural resources is becoming more difficult each day, basically due to the environmental damages caused by this type of activity. This work presents a study on the thermal behaviour of Brazilian tires using thermogravimetric analysis and differential thermal analysis, in order to optimise the pyrolysis process of tires. Samples of I to 2 mm were investigated at atmospheres of nitrogen, argon, oxygen and mixtures of these gases at temperatures up to 1273K, under heating rates between 1 to 50 Klmin . The results showed that the behaviour of each sample is related to both the atmosphere composition and the heating rate.

Jan 1, 2001

By Natasa Mitevska

The statistical analysis of the slag composition influence on copper losses to discard slag in the reverberatory furnaces No.1 and No.2 in the RTB BOR, Copper Smelter and Refinery (Yugoslavia) is presented in this paper. The model for the slag basicity calculation is determined, and connected to the copper distribution coefficients between the matte and slag phase. The influence of all components on the slag structure is also illustrated.

Jan 1, 2003

By V. L. Stolyarova

As part of an effort to develop the fluoride electrolysis route for the production of rare earth metals and alloys, a study of the thermodynamic properties of DyF3 has been carried out by Knudsen cell mass spectrometry. A quadrupole mass spectrometer QMS 420 was used in conjunction with the Knudsen cell arrangement. The experiments were carried out in the temperature range 1280-1440 K. Vaporization was carried out from platinum, molybdenum and tantalum cells. The Dy*, DyF+, DyF2+ fragment ions and the DyF3 parent ion were identified in the mass spectrum of the DyF3 vapour. The DyF, vapour pressure was obtained by the complete isothermal vaporizadon method as well as the ion current comparison method, and the enthalpy of sublimation of DyF3 was evaluated. From the DyF3 vapour pressure data obtained at different temperatures, the enthalpies of formation of DyF3 in the gaseous as well as condensed phases have been evaluated. The experimental data are compared with the thermodynamic information available in literature.

Jan 1, 1995

By Marco Pasetto

The possibility to re-use marginal materials (by-products) deriving from industrial activities in the construction of road infrastructures, as total or partial substitution of natural aggregates, successfully combines demands for economy and environmental sustainability. The paper presents the results of a laboratory study, conducted at the Experimental Road Laboratory of the University of Padova, to verify the suitability of a particular type of electric arc furnace slag to be recycled in the lithic skeleton of high-performance asphalt mixes (porous asphalt, high modulus mixes, stone mastic asphalt, nonskid surfacings) for road and airport flexible pavements. the process of transformation of iron and steel slag into a product that can be used in road building is described, along with the characterisation of the mixtures, plus an analysis of the results of a wide battery of mechanical-performance tests. This study forms part of wider theoretical ? experimental research being done at the University of Padova in order to improve knowledge of the characteristics of succedaneum materials and check their possible applications in road and airport construction.

Jan 1, 2006

By D. T. Smith, L. M. Hsiung, J. J. Schmitt, J. W. Golz, R. L. Lankey, H. N. G. Wadley, J. Z. Zhang, B. L. Halpern

"The microstructure and mechanical properties of Al/AI2O 3 metal-oxide nanolaminates fabricated by' a novel Jet Vapor Deposition (JVD) process at substrate temperatures of ~25° and -250°C have been investigated using transmission electron microscopy (TEM) and nanoindentation methods. The thickness of the oxide layer was held constant between 2 and 5 nm, whilst the Al layer thickness was systematically varied from -3 to -50 nm. Continuity of the Al layers was significantly improved when the nanolaminates were deposited at an elevated substrate temperature (-250°C). The yield strength of the nanolamintes with Al layers greater than -25 nm follows a Hall-Petch type relationship, whereas that of the nanolaminates with Al layers less than -25 nm is better predicted by a Koehler-Lehoczky strengthening model. IntroductionAluminum-aluminum oxide (presumably A12O3) nanolaminates have been recently fabricated using a novel Jet Vapor Deposition (ND) process developed and patented by Jet Process Corporation [1-4]. ND uses sonic, high purity helium (He) gas jets to entrain atomically dispersed vapor and deposit films. It is of interest here because it can deposit multilayered structures (laminates) inexpensively at high rates. Materials with a thin, multilayer structure are of interest because they potentially offer novel mechanical and physical properties [5]. Koehler in 1970 used an image force model to investigate the strength of laminated materials and proposed the use of alternating layers of high and low shear modulus metals to produce high strength composite materials [6]. He predicted that dislocations would have to overcome a large repulsive image force in order to move from metal layer B of lower shear modulus (uB) into metal layer A of higher shear modulus (uA)' The image force (F) is given by the relation:"

Jan 1, 1994

By Heikki Jalkanen

Oxygen converting of hot metal (LD/BOF) is contemplated as an object of simulation. Oxygen converting is a highly complex thermo-chemical process comprising a series of matter and energy transformation and transportation steps that makes the simulation very challenging. The basic principles of CONSIM 5 oxygen converter simulator are presented. Simulator is a comprehensive combination of a physical model with several empirical submodels describing all properties and processes that affect the final result of a converter blow, final mass and composition of steel, slag, dust and converter gas as well as the end temperature of steel. CONSIM simulator is used for simulation of series of high and low carbon steel blows. Simulated steel temperatures, oxygen consumption, blow time and iron oxide content of slag are compared with measured values. Problems of simulation and requirements for quantitative simulation of oxygen converter process are discussed.

Jan 1, 2006

By Xiaodi Huang, Matthew Andriese, Zheng Zhang, Jiann-Yang Hwang, Zhiwei Peng

"The thermal decomposition and regeneration behaviors of wüstite were investigated by in situ high temperature X-ray diffraction (HT-XRD) under non-isothermal condition at heating rate of 4 K min-1 in vacuum ranging from 294 K to 973 K. Wüstite on heating decomposes to magnetite and iron up to 823 K, above which it exhibits marked tendency to regenerate. Investigation of thermal stability of the reaction system shows that the decomposition proceeds under kinetic reaction control while the regeneration is under thermodynamic control. Kinetics study based on the Coats-Redfern integral approximation method indicates that the decomposition reaction follows a Komatsu-Uemura model-based diffusion-controlled kinetics with activation energy of 32.860 kJ mol-1. The thermodynamics analysis of regeneration reaction demonstrates that wüstite regenerates at lower temperature than stoichiometric ferrous oxide.IntroductionOwing to its importance in preparing various magnetic ceramic/metal nanocompostites or nanocrystals with high values of coercivity for the application as recording media, wüstite (non-stoichiometric ferrous oxide) has been attracting the attention of scientists over a long period [1-6]. The thermal behavior of wüstite was investigated by several researchers and phase transformations due to thermal decomposition and regeneration of wüstite during the heating in a specific temperature range was observed [7-9]. In spite of wüstite being found to dissociate to magnetite and iron at temperatures lower than 848 K and then regenerates at higher temperature, a clear understanding of the reaction mechanisms is clearly lacking [9]."

Jan 1, 2012

By Matti Hämäläinen

Outokumpu has developed a new chloride leaching process, HydroCopper?, for copper concentrates. The process utilizes the cupric ion as oxidant, which is able to dissolve chalcopyrite. After solution purification monovalent copper is precipitated as cuprous oxide, Cu2O, using sodium hydroxide. Copper product is produced from Cu2O by reduction, melting and casting. An essential part of the new process is chlor-alkali electrolysis, which regenerates the reagents used. All impurity metals are removed before Cu2O precipitation, because otherwise they would report to the copper product, impairing its quality. A multistage solution purification scheme has been developed consisting of firstly, chemical precipitation of impurity metals by pH increase, secondly, cementation of silver and thirdly, removal of trace multivalent ions using ion exchange. This paper describes the characteristics of solution purification in the HydroCopper? process based on the laboratory tests and pilot runs made by Outokumpu Research Oy.

Jan 1, 2003