Search Documents

By Yonggang Liu

Microstructure and precipitates in hot rolled low carbon steel sheet by CSP were investigated in this paper. It is pointed out the precipitates in low carbon steel sheet by CSP are different with that by traditional hot rolling. The bainites were found in CSP hot rolled steel sheet by TEM testing and these bainites could maintain in the sheets even after batch annealing. The selected area electron diffraction analyzing indicated that there were many CrB2BN and FeB4BN phases precipitated in hot rolled steel sheet and no AlN grains precipitated. The nitrides forming can limit AlN grains precipitating during the batch annealing processing, and this could do harm to the texture pipeline along orientation line forming with formed properties.

Jan 1, 2006

By R. F. Hammen

Copper is one of the most widely used metals in industrial processes and is also present in most mining operations. Extraction of copper from solutions often proves difficult due to the presence of complexing agents. ChromatoChem, Inc. has developed a Solid Phase Extraction (SPE) support (HiPAC) for removal and recovery of metals from wastewater. The HiPAC SPE support employs chelating agents covalently coupled to a long linker molecule. Several solutions containing copper and complexing agents were tested including 1) copper and carbonate, pH 9.8, 2) mixed metals and anions with copper and cyanide, pH 11, and 3) copper and the chelating agent EDTA, pH 11. The copper was extracted from solutions one and two at high pH, but the EDTA containing solution needed the pH lowered to make the copper available for capture. In each example, the copper concentration was significantly reduced by HiPAC SPE treatment.

Jan 1, 1994

By H. Masuda

The lijima Zinc Refinery started operation in 1972, and has today an annual capacity of 200, 000+-Zn. The hematite process was employed for the first time and the ideal of waste-free refinery has been pursued for 30 years. In recent years, however, only half of the hematite produced would be sold to the cement industry and hence a reduction of arsenic level has been necessary in order to sell the entire amount produced, The arsenic cementation process with zinc powder, developed through a long time laboratory research was found among some options as the best for the hematite process. The construction work started in 2000 and the facility was put into operation in 200 I. As a result in the same year all hematite were sold to the cement industry. The outline of this project, present operations and technical issue are reported in this paper.

Jan 1, 2003

By Hai-Peng Guo, Lu Jiang, Xiao-Man Yan, Bing Xie, Hong-Yi Li

Traditional, calcium compounds cannot be used in vanadium extraction processing due to the limitation of sodium roasting technology, which results in unsatisfied dephosphorization for vanadium-containing hot metal in converter and thus increasing the dephosphorization burden for subsequent steelmaking. The calcium roasting technology is an alternative for vanadium extraction and allows adding lime into vanadium slag in converter. In the present study, vanadium was leached by soda from roasted vanadium slag with high calcium content. Effects of roasting temperature and time, leaching temperature, Na2CO3 concentration andliquid to solid ratio on vanadium leaching rate were studied. The results show that 94% of vanadium was extracted by roasting the vanadium slag at 950℃ for 2.5h and then leaching in 160g/L Na2CO3 liquid at 95℃ for 1h with liquid to solid ratio of 10:1 ml/g. Impurities of Si and P reacted with calcium and formed insoluble Ca2SiO4 and Ca3(PO4)2 respectively.

Jan 1, 2015

By Arthur G. Hunt

Smelting using the direct-to-blister process commenced at Olympic Dam on 31 July 1988. The unique nature of the Olympic Dam ore body led to the selection of the direct to blister smelting process. Significant improvement in the design of the furnace and the understanding of the fundamentals of the process and its operation has occurred in the 10 years of operation. The paper will discuss the operation of the #1 Smelter and the design, preparation for start up and early operating experience of the #2 Smelter.

Jan 1, 1999

By Jackson Jenkins

The second survey of world copper SXEW plants has been completed. Solvent extraction and electrowinning data published in 1996 has been updated and leach data from seventeen plants is now included. The following pages list the results of the thirty- two plants that responded to the survey. Selected information is summarized in graphical form.

Jan 1, 1999

By Akira Yazawa

Oxidic dissolution loss of metal in slag is discussed thermodynamically in terms of oxygen potential, activity coefficient and equilibrium constant. To understand basic principle, regular solution model is applied for model calculation of the activity behaviour of metal oxide in FeO-SiO2-CaO slag, and effects of slag composition, temperature, and basicity of oxide on dissolution loss are demonstrated. As: a simplified but practical conclusion, the dissolved metal loss in slag is inversely proportional to activity coefficient of metal oxide, and also to FeO content in slag when amount of slag is taken account.

Jan 1, 1994

By E. A. Trillo, L. E. Murr, R. D. Flores, J. C. McClure, B. M. Nowak

Complex vortex and swirl-like solid-state flow phenomena have been observed in the residual microstructures characterizing the friction-stir welding (FSW) of copper to 6061 aluminum; 2024 aluminum to 6061aluminum,2024 aluminum to 1100 aluminum, 2024 aluminum to 7039 aluminum and 2024 aluminum to 2195 aluminum. These flow phenomena are characterized by intercalation lamellae composed of dynamically recrystallized grain structures of the dissimilar metals which provide a super-plastic-like mechanism for the FSW flow in the solid state; there is no melting and temperatures at the weld center do not exceed about 0.8 TM (where TM is the absolute melting temperature (K)). In experiments to be described and illustrated, optical or light metallography (LM), scanning electron microscopy (SEM) and transmission electron microscopy (TEM) techniques are utilized in examining residual FSW microstructures corresponding to tool rotation (stirring) speeds ranging from 400 to 1200 rpm, and traverse (or actual welding) speeds of 1 to 2 mrn/s.

Jan 1, 1999

By Per Anders Eidem, Merete Tangstad, Jens Davidsen

"During excavations of submerged arc furnaces producing silicomanganese, silicon carbide (SiC) has been found. Contributing to the size of the inactive area of the furnace, the active area of the furnace where reactions occur will decrease, thus reducing the potential for pre-reduction in the furnace.This work studied the formation of SiC from the liquid-solid reaction between slag, metal, and metallurgical coke. Slags and metals with different levels of silica (S1O2) and silicon (Si) have been studied. The slag and metal has been heated together with coke, and the samples investigated by microprobe. The results show that SiC was formed on the coke particle through reactions with both slag and metal. For the metal, the carbon most likely diffused through the SiC to react with Si in the alloy. SiC formation with slag is likely to go through the reduction of Si02 to Si.IntroductionToday, Silicomanganese (SiMn) is produced in submerged arc furnaces (SAF) by reduction of S1O2 and manganese oxides, mainly with metallurgical cokes. Typically, the tapped metal has a silicon content of 17 - 20 wt.%. To achieve higher levels of Si, the metal can be refined by adding off-grade silicon metal, yielding low carbon SiMn. [1]. What is believed to be SiC that has been found during dig-outs of SiMn furnaces producing high silicon alloy. It is possible that excess amounts of SiC in the furnace cause operational problems, since SiC will occupy furnace volume. As SiC accumulates, the active volume of the furnace will decrease, increasing the flow of material and gas in the active areas of the furnace. Formation of SiC is inevitable, so it is desired to keep the formation as low as possible. To be able to control the formation of SiC, one has to understand the basic mechanisms."

Jan 1, 2012

By Marshall Khan

The Goodfellow Expert Furnace System Optimization Process (Goodfellow EFSOP?) is a proprietary process that uses real-time and continuous off-gas analysis, along with process monitoring to optimize the operation of electric arc furnaces (EAF) for steelmaking. With the exception of off-gas composition, dynamic process measurements within the EAF are not possible due to the harsh operating environment. The Goodfellow EFSOP? system provides a dynamic indication of the operating conditions within the EAF. Continuous measurement of furnace off-gas composition, along with other furnace operating parameters is used to elucidate the fate of chemical energy usage within the EAF including: the evolution of carbon from the molten steel bath; the in-leakage of air into the furnace; the extent of combustion above the molten steel bath and the occurrence of dangerous water-leaks from the furnace cooling system. The ability to measure the process reliably and continuously enables Techint Goodfellow Technologies Inc (TGTI) to implement dynamic process control of combustion within the electric arc furnace and to optimize the overall operation through adjustments to the EAF process based on off-gas measurement. This paper discusses the methodology and results achieved from several recent Goodfellow EFSOP? installations in South East Asia.

Jan 1, 2006

By Ralph P. Hackl

Bacterial leaching of the Doe Run Company?s cobalt/nickel-containing copper concentrate at low pH (pH 1.0-1.2) and high redox potential (>750 mV vs. SHE) enabled the cobalt and nickel to be preferentially dissolved over copper and iron due to the rapid passivation of the chalcopyrite component. Selective leaching of the cobalt and nickel was achieved with a mesophilic culture comprised mainly of Leptospirillum-like bacteria and Acidithiobacillus thiooxidans. This finding led to the conception of a novel hydrometallurgical process for passivating chalcopyrite and recovering the cobalt and nickel. The bacterial leaching process was tested extensively at the bench and pilot plant scales during 1997-1998. A pilot plant containing four leaching stages processed 30-40 kg/day of chalcopyrite concentrate continuously for 87 days. The cobalt extraction ranged from 75% to 86% during 6- and 8-day retention times respectively, whereas the copper extraction was limited to about 9%

Jan 1, 2003

By K. Suseelan Nair

Magnesium alloys containing rare earths are finding increasing applications in space programmes. A number of alloys have been developed and e good data base an the mechanical properties of these alloys is available. However details on metallurgical aspects are found to be sparse in, literature. This paper, at first, briefly reviews the available data on these alloys and subsequently presents the microstructural investigations conducted on quatenary fig-4.9% Zn-1% Rare earth-0.5% Zr cast alley, using optical metallic-graphy, electron probe micro-analysis and X-ray diffraction techniques.

Jan 1, 1989

By P. S. Dunn, A. D. Rollett, H. D. Lewis

"The results of preliminary work on the modeling and measurement of the heat transfer coefficients of metal/mold interfaces is reported. The system investigated is the casting of uranium in graphite molds. The motivation for the work is primarily to improve the accuracy of process modeling of prototype mold designs at the Los Alamos Foundry. The evolution in design of a suitable mold for unidirectional solidification is described, illustrating the value of simulating mold designs prior to use. Experiment indicated a heat transfer coefficient of 2 kW/m /K both with and without superheat. It was possible to distinguish between solidification due to the mold and that due to radiative heat loss. This permitted an experimental estimate of the emissivity, ~ = 0.2, of the solidified metal.IntroductionA feature that distinguishes casting processes from welding processes is the presence of an interface with a low heat transfer coefficient between the mold and the casting. Especially when chill casting, the interface delays the start of solidification and increases freezing times significantly. By comparison welds can be assumed to have a very high heat transfer coefficient. The heat transfer coefficient controls such phenomena as folds and laps on the surface of castings which can be crucial to the acceptability of a casting. The time delay for the start of solidification influences the occurrence of cold shut defects. The standard mold material for uranium casting is high quality graphite which is an excellent refractory when used in vacuum and coated with a refractory wash. Graphite is an effective chill material and has a thermal diffusivity approximately twice that of uranium. Experience has shown that practicable superheat without mold pre-heat is not sufficient for avoiding cold shut defects when casting in graphite molds.TheoryIt is possible to calculate the position of the freeze front s, as a function of time, t, the superheat and interface heat transfer coefficient, h, [1]. However, the value of h cannot be obtained explicitly. The Virtual Adjunct Method (VAM) [2] offers a method for extending the standard equation for an insulating mold where s is proportional to the square root of time. By considering the effect of the interface to be equivalent to finite thicknesses of mold and metal, the following quadratic equation is obtained,"

Jan 1, 1986

By David E. Hardt

"One of the critical variables to be controlled during arc welding is the size or geometry of the weld pool. The measurement of pool geometry has become an increasingly important problem with the advance of welding automation and control, and this paper addresses that problem. The basic concept of pool size estimation via measurement of pool dynamics is presented. The theory underlying this concept is discussed and is followed by a review of the current work in this area. It is concluded that pool dynamics can be characterized by natural frequencies of oscillation, for stationary welds, and that these can be measured by appropriate signal processing performed on the arc voltage. However, it appears that only full penetration welds show a strong correlation between weld size and natural frequency. Also, the extension of these results to the realistic case of moving welds has yet to be considered in detail. Nonetheless, this method of in-process measurement for real-time weld process control is still quite attractive where applicable since it can be accomplished simply by modifying the arc current schedule and by signal processing of the arc voltage.INTRODUCTUIONThe study of welding process control has been dominated by research into methods of in processing sensing of the weld pool geometry. While it has been shown feasible to measure the topside pool geometry using video methods [1,2], the penetration or backside bead width have remained elusive quantities. This is particularly true if a topside sensor location is required.The concept of using weld pool motion as a pool geometry sensing method was proposed by Hardt et al. [3] and later demonstrated by Hardt and Zacksenhouse [5] and Richardson and Renwick [6]. The concept is based on the fluid dynamics of a pool constrained by a solid container and by significant surface tension forces (i.e. a small shallow pool, not a ""pond"" or ""lake""). Such a pool, if subjected to external forces, will exhibit a surface motion is a function of that force, the properties of the fluid, the surface tension, and the shape of the container. Thus, if this motion can be excited and measured, and the relationship to the pool geometry determined, a means of sensing pool shape will exist."

Jan 1, 1986

Testing is in progress to address compatibility issues with regard to long term storage of plutonium in contact with two different intermetallic systems. The two intermetallic systems are: 1. dental amalgam, i.e., mercury plus silver alloy powder, and 2. liquid gallium alloy plus copper powder. Both of these are plasto-metallic materials that undergo a solidification reaction at room temperature. Each system is allowed to react in contact with both high-purity alpha plutonium and a delta stabilized plutonium alloy at varying temperatures in an argon atmosphere. Wetting characteristics and possible interaction will be studied metallographically in the post-mortem condition. Complete results including metallographic examinations will be presented.

Jan 1, 1995

By Hye-Sung Kim, Dong-Wha Kum, Gyeungho Kim

"Mechanical alloying is an effective way to finely distribute inert dispersoids in AI-TM (TM is a transition metal element) systems. It is considered that high melting point aluminides are formed by precipitation from the supersaturated aluminum matrix. The analysis is based on the fact that much higher content of TM than the solubility limit can be dissolved in alpha aluminum during the high energy ball milling. Nonetheless, the role of undissolved TM particles affecting the formation of aluminides is not suitably considered. In this paper, authors present experimental observation on the formation of Ab3Ti particles from mechanically alloyed AI-Ti alloys in the hyper-peritectic region. This study showed that, in the mechanically alloyed AI-20wt%Ti specimen, intermediate phase of cubic Ab3Ti and tetragonal AIz4Tis formed at 300 - 400°C and 400 - 500°C, respectively, before the MA-state reaches to the global equilibrium at higher temperatures. The formation behavior of Lh- Ab3Ti is interpreted by interdiffusion of Al and Ti in solid state based on the fact that large amount of nano-sized Ti particles exist in the milled powder. Present analysis indicated undissolved Ti particles of nanosize should have played an important role initiating the formation of Ab3Ti phase during annealing.IntroductionInterest in the hyper-peritectic AI-Ti alloys is based on industrial demand for high-modulus and high-temperature aluminum alloys. Earlier works on hyper-peritectic AI-Ti alloys with 4 to 12wt%Ti show that these alloys are strong at ambient temperature and maintain high strength above 300°C when titanium-trialuminide (e.g., Ab3Ti) is finely distributed in the aluminum matrix [1,2]. High melting point and high stiffness with low density of AbTi make the AI-Ti alloys strong with greater thermal stability while keeping weight savings as much as possible. Titanium in aluminum shares other merits of transition metal additions because Ti solubility in Al is low (i.e., 1.l5wt%Ti at 665°C and virtually zero below 400°C), and fine dispersion of Ab3Ti particles is readily accomplished and resists grain coarsening effectively."

Jan 1, 1996

By Tarek M. Abd El Hamid, Suzane Ali

"Treatment of industrial waste materials is created serious problem in Egypt. Aluminium sludge is generated as a by-product from aluminium household industry which contains significantly high alumina content exceeding 90%. This by-product randomly disposed and creates serious environment problems to locate community. To develop the treatment process of this material, the recovery of high purity alumina and identify the potential application is being the primary objective, This paper represents the recovery process of alumina process waste sludge High purity alumina material <99.8% aluminium oxide with originate particle size 0.125-0.420mm and apparent density 0.39g/cm3 was obtained with a specific surface area 139m2/g. Alumina produced was modified by cerium oxide doped alumina. The catalytic activity and selectivity was investigated in conversion of iso-propanol via dehydrogenation reaction yielding only acetone indicating an excellent selectivity the dehydrogenation. The presence of 10% CeO2 increase in the catalytic activity of 82% for the originated alumina. Introduction Approximately 20 thousand tons of aluminium waste produced in Egypt in 2006 with increasing amounts expected in succeeding years. A part of this waste contains organics impurities which coexisted with aluminium waste as a result of manufacture final aluminium products, waste usually content <1 to 2 wt% of organic carbon. It's generally admitted that the organic species are present in the form of lubricant oils used in rolling and pressing equipments for aluminium sheet. Both industry and government face possible high-cost disposal problems that more magnified by large volume of waste produced. The alumina recovery leachable study conduct in this paper had the following objectives: 1- Develop a process that can provide an environmentally acceptable residue and also recover the available alumina. 2- Evaluate the alumina produced in terms of grade and catalytic application."

Jan 1, 2008

By Stephen R. Brown

Current conditions in the copper market demand that mine and plant operators make budgeted production targets at the lowest possible unit costs. For those companies bringing new production capacity on-line, achieving budgeted production levels as quickly as possible after start-up is vitally important to minimize unit costs and to begin a positive cash flow. Whether the objective is to simply improve unit costs or successfully start-up a new, complex plant, success will be strongly influenced by .the skill levels of the operators :and supervisors. The only way to assure return on plant investment, and to survive during depressed metal prices, is to ensure that plant operators have the knowledge to effectively run the plant. Technology available in computer-based, multimedia training systems, including: interactive animation, videos, voice-overs, schematics, and text can now be used to train operators at their own pace using plant-specific information. Additionally, it has been shown that learning through multimedia provides a higher degree of long term retention than more traditional learning methods.

Jan 1, 1999

By Kazuteru Tozcwa

The oxidation of several sulfide minerals in aqueous ammoniacal solution is discussed thermodynamically. The region in which Cu(NH3)2 4+ is stable has been estimated as a function of pH and concentration of total ammonia, {[NH3) + [NH4)}. In ammonia leaching when copper in sulfides is assumed to be extracted in the form of Cu(NH3)2 which will be rapidly converted to cupric ammine, thermodynamic data predict that such minerals are oxidized readily in the following order, CuS, Cu2S, CuFeS2, ZnS, NiS, Ag2S. This agrees with investigations on ammonia leaching of sulfide minerals, reported previously. The leaching of copper sulfide concentrate has been examined experimentally. Copper in a copper sulfide concentrate, in which the main constituents were chalcopyrite and pyrite, was effective¬ly extracted. The copper extraction was affected by factors such as (1) agitation intensity, (2) oxygen partial pressure, (3) NH3/Cu molar ratio, (4) leaching temperature and (5) addition of ammonium sulfate. From the results obtained in this work, it is concluded that mass transfer of oxygen plays the most important role in ammonia leaching of copper sulfide minerals.

Jan 1, 1976

By V. Vergara

Four copper composites were obtained by mechanical alloying, using as dispersed phases of four carbide powders; they were: boron carbide, chromium carbide, silicon carbide and zirconium carbide. The purpose of this work was to study some characteristics of these compounds and their feasibility for use as materials for electrical equipment. Raw materials used were copper powder finer than 150 mesh, and 2-4 vol % of powder carbides finer than 325 mesh. The alloying process was carried out using both a Spex 800-D mill with tungsten jars and balls and a hardened stainless steel jar and balls, the purpose of which was to measure the degree of contamination induced by the milling media. The changes in particle size, morphology and microstructure of copper alloys were studied with SEM and TEM for each alloyed powder. The degree of saturation of copper by the carbides was measured by X-ray diffraction. Sound samples were obtained by hot isostatic pressing at 1073°K. The best characteristics were obtained for the compound copper-chromium carbide, based on their hardness, tensile strength and electrical conductivity values. The other alloys failed due to their excessive brittleness after hot pressing.

Jan 1, 1999